Intel 82599ES; GPON SFP module not working

stephenw10

Hmm, no error there. There's not really much that can be set for those NICs beyond what you tried already.

Does really only show an active link when the upstream fiber is disconnected?

milindhvijay

@stephenw10 Yes, only shows active when ISP fiber is disconnected?

Would updating the driver help? If so, how can I do it?

stephenw10

I doubt it would make any difference but you could try to either build it yourself or install the kmod port for ixgbe. It may be marginally newer. Finding a version that loads can be challenging though since it has to closely match the kernel.

When the optic is disconnected do both modules show as active?

In that state can you connect to their cli through pfSense?

milindhvijay

No, Hisense-Leox LXT-010S-H shows active and power(green) and activity(amber) indication light is constantly ON when optic is disconnected. With optic connected, lights come ON in constant intervals, stays ON for 2-3 seconds and turns OFF. Without optics I am able to get into the admin page and telnet works.

HSGQ-XPON-Stick shows no carrier with or without optic. Even the power/activity lights are off always. Never even seen (rxpause, txpause) in interfaces. If I remember right, it always stay on autoselect.

I think HSGQ-XPON-Stick does not work because it is a 2.5G stick and AFAIK Intel x520 supports only 1G and 10G. I've tried forcing it to 1G but no luck.

stephenw10

Indeed only the x550 support N-Base and I think it's only N-BaseT. I don't have one to test with.

You can try setting the advertise speeds to 1G only in the negotiation:

[24.03-DEVELOPMENT][root@8200.stevew.lan]/root: sysctl -d dev.ix.0.advertise_speed
dev.ix.0.advertise_speed: 
Control advertised link speed using these flags:
	0x1 - advertise 100M
	0x2 - advertise 1G
	0x4 - advertise 10G
	0x8 - advertise 10M

	0x10  - advertise 2.5G
	0x20  - advertise 5G

	100M and 10M are only supported on certain adapters.

That still requires a compatible module though so may not allow it.

milindhvijay

[2.7.2-RELEASE][admin@Gaia.home]/root: sysctl -d dev.ix.0.advertise_speed
dev.ix.0.advertise_speed:
Control advertised link speed using these flags:
	0x1 - advertise 100M
	0x2 - advertise 1G
	0x4 - advertise 10G
	0x8 - advertise 10M

	0x10  - advertise 2.5G
	0x20  - advertise 5G

	100M and 10M are only supported on certain adapters.

How do I set the flag?

stephenw10

Like:

[24.03-DEVELOPMENT][root@8200.stevew.lan]/root: sysctl dev.ix.2.advertise_speed=1
dev.ix.2.advertise_speed: 11 -> 1

But it has to have a device that supports those speeds. ix2 there is a combo port so it supports 1G, 100M, 10M baseT.

milindhvijay

[2.7.2-RELEASE][admin@Gaia.home]/root: sysctl dev.ix.0.advertise_speed=1
dev.ix.0.advertise_speed: 0
sysctl: dev.ix.0.advertise_speed=1: Invalid argument

stephenw10

Mmm, it may not work. You would need to set it to 2 there though. 1 is 100M which is almost certainly not supported on that NIC.

milindhvijay

Any option would return invalid argument. I tried this a couple days ago.

stephenw10

Mmm, I suspected as much. That option depends on the NIC/module combination and it's not seeing anything as valid with that module present.

bunneo

@milindhvijay hey did you figure this out?
having same issue, HSGQ-XPON-Stick shows no carrier, no lights.

milindhvijay

@bunneo Nope