Problem booting netgate 2100

Benito 0 · Jan 29, 2024, 11:58 AM

Hello team, today I encountered an error where my Netgate 2100 was not loading and was stuck at a blinking blue light on the circle LED.
Since am not tech-savvy I just connected to the console port and rebooted the device and the following boot log appeared with an error. any help would be highly appreciated thanks.

OK reboot
resetting ...
TIM-1.0
WTMI-devel-1.0.0-1115f12
WTMI: system early-init
SVC REV: 5, CPU VDD voltage: 1.237V
NOTICE: Booting Trusted Firmware
NOTICE: BL1: v1.5(release):ROGUE2-01.00.00.01-cpu1_2G-0-g06b570a8d (Marvell-release-1.3.0)
NOTICE: BL1: Built : 14:34:11, Feb 7 2020
NOTICE: BL1: Booting BL2
console comconsole failed to initialize0.00.01-cpu1_2G-0-g06b570a8d (Marvell-release-1.3.0)
Consoles: EFI console 4:34:13, Feb 7 2020
Reading loader env vars from /efi/freebsd/loader.env
Setting currdev to disk1p1:):ROGUE2-01.00.00.01-cpu1_2G-0-g06b570a8d (Marvell-release-1.3.0)
FreeBSD/arm64 EFI loader, Revision 1.1
(Fri Feb 10 20:26:39 UTC 2023 root@freebsd)
U-Boot 2018.03-devel-1.2.0ROGUE2-01.00.00.02+ (Feb 07 2020 - 14:33:22 -0500)
Command line arguments: loader.efi
Image base: 0x1000000
EFI version: 2.70[MHz]
EFI Firmware: Das U-Boot (rev 0.00)
Console: efi,comconsole (0)
Load Path: /\efi\boot\bootaa64.efi
Load Device: /VenHw(e61d73b9-a384-4acc-aeab-82e828f3628b)/Scsi(0,0)/HD(1,0x01,0,0x1,0x64000)
Trying ESP: /VenHw(e61d73b9-a384-4acc-aeab-82e828f3628b)/Scsi(0,0)/HD(1,0x01,0,0x1,0x64000)
Setting currdev to disk1p1:25 Gbps
Trying: /VenHw(e61d73b9-a384-4acc-aeab-82e828f3628b)/Scsi(0,0)/HD(2,0x01,0,0x64001,0x1117c)
Setting currdev to disk1p2:bps
Trying: /VenHw(e61d73b9-a384-4acc-aeab-82e828f3628b)/Scsi(0,0)/HD(3,0x01,0,0x7517d,0x3b2dd33)
Setting currdev to disk1p3:
ERROR: cannot open /boot/lua/loader.lua: no such file or directory. ofdata clock 200000000, frequency 20000000
SF: Detected w25q32bv with page size 256 Bytes, erase size 4 KiB, total 4 MiB
OK
Type '?' for a list of commands, 'help' for more detailed help.
OK : eth0: neta@30000 [PRIME], eth1: neta@40000
Hit any key to stop autoboot: 0
Setting bus to 1
** No partition table - mmc 0 **

Reset SCSI
scanning bus for devices...
Bus 0
Device 0: (0:0) Vendor: ATA Prod.: ATP SATA III M.2 Rev: SBFM
Type: Hard Disk
Capacity: 30533.8 MB = 29.8 GB (62533296 x 512)
12725 armada-3720-netgate-1100.dtb
12725 armada-3720-sg1100.dtb
12948 armada-3720-netgate-2100.dtb
12948 armada-3720-sg2100.dtb

4 file(s), 0 dir(s)

12948 bytes read in 4 ms (3.1 MiB/s)
839196 bytes read in 24 ms (33.3 MiB/s)

Starting EFI application at 01000000 ...

Scanning disk sdhci@d8000.blk...
Scanning disk ahci_scsi.id0lun0...
Found 5 disks

Benito 0 · Jan 29, 2024, 2:15 PM

Update: Was able to contact negate support and they assisted me thanks.