WAN only connects on unplug and plug back in
-
@randombits said in WAN only connects on unplug and plug back in:
Does pfSense assume the WAN is vtnet0 or vtnet1 ?
It has no preset config for vtnet, the user has to assign those interfaces manually.
If you have em NICs it will initially use em0 as WAN unless you set it differently.
vmstat is used by a package you have installed so probably darkstat or Banwidthd. If you resave the config in that package it should remove those old NIC references.
-
@stephenw10 I removed both darkstat & bandwidthd and reinstalled them but the orphaned interfaces are still in the log.
I just looked in config.xml and there's no reference to emX.XXX etc only vtnet's
Just spotted this, but not sure how relevant it is
Aug 20 18:28:30 php-cgi 453 rc.bootup: Default gateway setting Interface WAN_DHCP Gateway as default. Aug 20 18:28:30 php-cgi 453 rc.bootup: The command '/sbin/route -n6 get 'default' 2>/dev/null | /usr/bin/egrep 'flags: <.*PROTO.*>'' returned exit code '1', the output was '' Aug 20 18:28:31 kernel done. Aug 20 18:28:34 php-cgi 453 rc.bootup: sync unbound done. Aug 20 18:28:35 kernel done.One thing, many thanks for bearing with me - I do very much appreciate it !
-
Yes, that's what I pointed out above. It may or may not be the issue but it's certainly suspicious.
What interface references are you seeing now?
What packages do you still have installed?
-
@stephenw10 Packages
And these still hanging around
Aug 20 18:29:28 vnstatd 41582 vnStat daemon 2.11 (pid:41582 uid:0 gid:0, SQLite 3.43.1) Aug 20 18:29:28 vnstatd 41582 Data retention: 48 5MinuteHours, 4 HourlyDays, 62 DailyDays, 25 MonthlyMonths, -1 YearlyYears, 20 TopDayEntries Aug 20 18:29:28 vnstatd 41582 Monitoring (22): vtnet1 (10000 Mbit) vtnet0.999 (10000 Mbit) vtnet0.40 (10000 Mbit) vtnet0.30 (10000 Mbit) vtnet0.20 (10000 Mbit) vtnet0.10 (10000 Mbit) vtnet0 (10000 Mbit) tun_wg1 (1000 Mbit) tun_wg0 (1000 Mbit) pppoe0 (1000 Mbit) pfsync0 (1000 Mbit) pflog0 (1000 Mbit) ovpns1 (1000 Mbit) ovpnc2 (1000 Mbit) enc0 (1000 Mbit) em1 (1000 Mbit) em0.999 (1000 Mbit) em0.40 (1000 Mbit) em0.30 (1000 Mbit) em0.20 (1000 Mbit) em0.10 (1000 Mbit) em0 (1000 Mbit) Aug 20 18:29:28 vnstatd 45241 Error: pidfile "/var/run/vnstat/vnstat.pid" lock failed (Resource temporarily unavailable), exiting. Aug 20 18:29:28 vnstatd 41582 Interface "tun_wg1" disabled. Aug 20 18:29:28 vnstatd 41582 Interface "tun_wg0" disabled. Aug 20 18:29:28 vnstatd 41582 Interface "pppoe0" disabled. Aug 20 18:29:28 vnstatd 41582 Interface "em1" disabled. Aug 20 18:29:28 vnstatd 41582 Interface "em0.999" disabled. Aug 20 18:29:28 vnstatd 41582 Interface "em0.40" disabled. Aug 20 18:29:28 vnstatd 41582 Interface "em0.30" disabled. Aug 20 18:29:28 vnstatd 41582 Interface "em0.20" disabled. Aug 20 18:29:28 vnstatd 41582 Interface "em0.10" disabled. Aug 20 18:29:28 vnstatd 41582 Interface "em0" disabled. Aug 20 18:29:28 tail_pfb 46393 [pfBlockerNG] Firewall Filter Service stopped Aug 20 18:29:29 php_pfb 47122 [pfBlockerNG] filterlog daemon stopped Aug 20 18:29:29 tail_pfb 53027 [pfBlockerNG] Firewall Filter Service started Aug 20 18:29:29 root 53976 Bootup complete -
Do you still see those is Bandwidthd and darkstat are disabled?
-
@stephenw10 yes, I removed both packages and not reinstalled and the interface references are still there after a reboot
-
Hmm, and still from vnstatd?
I'd backup the config and search it directly for em references.
-
@stephenw10 yes vmstatd, bit difficult on a phone atm, I'll save and look at the config.
-
Right then, No reference to em interfaces at all only vtnet ones.
Ah-ha ! I removed Traffic totals and rebooted and the vnstatd interfaces references have gone.
Although the rebooting WAN issues remains
-
Ah, you may need to clear the traffic totals data then if you still need that. Though it clearly isn't what's preventing the default route.
-
@stephenw10 The traffic totals cleared themselves but I also reset them.
For clarity here is the log now.
------------- pfSense rebooted ------------ Aug 21 12:37:54 kernel Features2=0x82b82201<SSE3,SSSE3,CX16,SSE4.1,SSE4.2,x2APIC,POPCNT,AESNI,HV> Aug 21 12:37:54 kernel AMD Features=0x20100800<SYSCALL,NX,LM> Aug 21 12:37:54 kernel AMD Features2=0x1<LAHF> Aug 21 12:37:54 kernel Hypervisor: Origin = "KVMKVMKVM" Aug 21 12:37:54 kernel intsmb0: <Intel PIIX4 SMBUS Interface> irq 9 at device 1.3 on pci0 Aug 21 12:37:54 kernel intsmb0: intr IRQ 9 enabled revision 0 Aug 21 12:37:54 kernel smbus0: <System Management Bus> on intsmb0 Aug 21 12:37:54 kernel aesni0: <AES-CBC,AES-CCM,AES-GCM,AES-ICM,AES-XTS> Aug 21 12:37:54 kernel lo0: link state changed to UP Aug 21 12:37:54 kernel vtnet0: link state changed to UP Aug 21 12:37:54 kernel vlan0: changing name to 'vtnet0.10' Aug 21 12:37:54 php-cgi 453 rc.bootup: The command '/sbin/ifconfig 'vtnet1' inet6 delete' returned exit code '1', the output was 'ifconfig: ioctl (SIOCDIFADDR): Can't assign requested address' Aug 21 12:37:54 kernel vlan1: changing name to 'vtnet0.20' Aug 21 12:37:54 kernel vlan2: changing name to 'vtnet0.30' Aug 21 12:37:54 kernel vlan3: changing name to 'vtnet0.40' Aug 21 12:37:54 kernel vlan4: changing name to 'vtnet0.999' Aug 21 12:37:54 kernel vtnet1: link state changed to UP Aug 21 12:37:54 check_reload_status 428 Linkup starting vtnet1 Aug 21 12:37:54 php-cgi 453 rc.bootup: The command '/sbin/ifconfig 'vtnet1' media 'autoselect'' returned exit code '1', the output was 'ifconfig: SIOCSIFMEDIA (media): Operation not supported' Aug 21 12:37:54 kernel [fib_algo] inet.0 (bsearch4#28) rebuild_fd_flm: switching algo to radix4_lockless Aug 21 12:37:54 check_reload_status 428 rc.newwanip starting vtnet1 Aug 21 12:37:55 php-fpm 396 /rc.linkup: Ignoring link event during boot sequence. Aug 21 12:37:55 php-fpm 397 /rc.newwanip: rc.newwanip: Info: starting on vtnet1. Aug 21 12:37:55 php-fpm 397 /rc.newwanip: rc.newwanip: on (IP address: x.x.x.x) (interface: WAN[wan]) (real interface: vtnet1). Aug 21 12:37:56 check_reload_status 428 starting sshd Aug 21 12:37:56 php-cgi 453 rc.bootup: Resyncing OpenVPN instances. Aug 21 12:37:56 kernel done. Aug 21 12:37:56 kernel tun1: changing name to 'ovpns1' Aug 21 12:37:57 kernel ovpns1: link state changed to UP Aug 21 12:37:57 kernel tun2: changing name to 'ovpnc2' Aug 21 12:37:57 check_reload_status 428 rc.newwanip starting ovpns1 Aug 21 12:37:57 sshd 77964 Server listening on :: port 22. Aug 21 12:37:57 sshd 77964 Server listening on 0.0.0.0 port 22. Aug 21 12:37:57 sshguard 78881 Now monitoring attacks. Aug 21 12:37:58 kernel pflog0: promiscuous mode enabled Aug 21 12:37:58 php-fpm 396 /rc.newwanip: rc.newwanip: Info: starting on ovpns1. Aug 21 12:37:58 php-fpm 396 /rc.newwanip: Interface is disabled, nothing to do. Aug 21 12:38:01 kernel .done. Aug 21 12:38:01 kernel done. Aug 21 12:38:03 php-cgi 453 rc.bootup: Default gateway setting Interface WAN_DHCP Gateway as default. Aug 21 12:38:03 php-cgi 453 rc.bootup: The command '/sbin/route -n6 get 'default' 2>/dev/null | /usr/bin/egrep 'flags: <.*PROTO.*>'' returned exit code '1', the output was '' Aug 21 12:38:03 kernel done. Aug 21 12:38:07 php-cgi 453 rc.bootup: sync unbound done. Aug 21 12:38:07 kernel done. Aug 21 12:38:09 kernel done. Aug 21 12:38:39 kernel done. Aug 21 12:38:39 php-cgi 453 rc.bootup: NTPD is starting up. Aug 21 12:38:39 kernel done. Aug 21 12:38:40 check_reload_status 428 Updating all dyndns Aug 21 12:38:40 kernel done. Aug 21 12:38:41 kernel . Aug 21 12:38:41 kernel .. Aug 21 12:38:42 php-cgi 453 rc.bootup: The command '/usr/local/sbin/strongswanrc stop' returned exit code '1', the output was 'strongswan not running? (check /var/run/daemon-charon.pid).' Aug 21 12:38:42 kernel .done. Aug 21 12:38:46 php-cgi 453 rc.bootup: The command '/sbin/camcontrol standby da0 -t 0.5' returned exit code '1', the output was 'camcontrol: ATA STANDBY via pass_16 failed' Aug 21 12:38:46 php-cgi 453 rc.bootup: Creating rrd update script Aug 21 12:38:46 php-cgi 453 rc.bootup: The command '/usr/sbin/powerd -b 'min' -a 'min' -n 'min'' returned exit code '69', the output was 'powerd: no cpufreq(4) support -- aborting: No such file or directory' Aug 21 12:38:46 kernel done. Aug 21 12:38:47 syslogd exiting on signal 15 Aug 21 12:38:47 syslogd kernel boot file is /boot/kernel/kernel Aug 21 12:38:47 kernel done. Aug 21 12:38:47 php-cgi 92079 notify_monitor.php: Could not send the message to alert@XXXXXXXX.com -- Error: Failed to connect to ssl://smtp.googlemail.com:465 [SMTP: Failed to connect socket: php_network_getaddresses: getaddrinfo for smtp.googlemail.com failed: Name does not resolve (code: -1, response: )] Aug 21 12:38:47 php-fpm 397 /rc.start_packages: Restarting/Starting all packages. Aug 21 12:38:48 lighttpd_pfb 14154 [pfBlockerNG] DNSBL Webserver stopped Aug 21 12:38:48 lighttpd_pfb 15549 [pfBlockerNG] DNSBL Webserver started Aug 21 12:38:48 php 16207 [pfBlockerNG] DNSBL parser daemon started Aug 21 12:38:50 php-fpm 397 [pfBlockerNG] Starting firewall filter daemon Aug 21 12:38:50 tail_pfb 6980 [pfBlockerNG] Firewall Filter Service stopped Aug 21 12:38:50 php_pfb 7757 [pfBlockerNG] filterlog daemon stopped Aug 21 12:38:50 tail_pfb 9955 [pfBlockerNG] Firewall Filter Service started Aug 21 12:38:50 php_pfb 10695 [pfBlockerNG] filterlog daemon started Aug 21 12:38:50 vnstatd 16176 vnStat daemon 2.11 (pid:16176 uid:0 gid:0, SQLite 3.43.1) Aug 21 12:38:50 vnstatd 16176 Monitoring (12): vtnet1 (10000 Mbit) vtnet0.999 (10000 Mbit) vtnet0.40 (10000 Mbit) vtnet0.30 (10000 Mbit) vtnet0.20 (10000 Mbit) vtnet0.10 (10000 Mbit) vtnet0 (10000 Mbit) pfsync0 (1000 Mbit) pflog0 (1000 Mbit) ovpns1 (1000 Mbit) ovpnc2 (1000 Mbit) enc0 (1000 Mbit) Aug 21 12:38:53 arpwatch 18952 listening on vtnet0.10 Aug 21 12:38:53 kernel vtnet0: promiscuous mode enabled Aug 21 12:38:53 kernel vtnet0.10: promiscuous mode enabled Aug 21 12:38:53 arpwatch 18794 listening on vtnet0 Aug 21 12:38:53 arpwatch 19547 listening on vtnet0.30 Aug 21 12:38:53 kernel vtnet0.30: promiscuous mode enabled Aug 21 12:38:53 arpwatch 19188 listening on vtnet0.20 Aug 21 12:38:53 kernel vtnet0.20: promiscuous mode enabled Aug 21 12:38:53 arpwatch 20053 Link layer type 0 not ethernet or fddi Aug 21 12:38:53 kernel ovpnc2: promiscuous mode enabled Aug 21 12:38:54 kernel ovpnc2: promiscuous mode disabled Aug 21 12:38:54 kernel vtnet0.999: promiscuous mode enabled Aug 21 12:38:53 arpwatch 20289 listening on vtnet0.999 Aug 21 12:38:54 arpwatch 20571 pcap open : : No such device exists (No such device exists) Aug 21 12:38:54 arpwatch 20902 listening on vtnet1 Aug 21 12:38:54 kernel vtnet1: promiscuous mode enabled Aug 21 12:38:58 php-fpm 43380 /index.php: Successful login for user 'admin' from: 192.168.2.21 (Local Database) Aug 21 12:38:58 sshguard 26469 Now monitoring attacks. Aug 21 12:39:01 vnstatd 17978 Error: pidfile "/var/run/vnstat/vnstat.pid" lock failed (Resource temporarily unavailable), exiting. Aug 21 12:39:01 vnstatd 20270 Error: pidfile "/var/run/vnstat/vnstat.pid" lock failed (Resource temporarily unavailable), exiting. Aug 21 12:39:01 lighttpd_pfb 21446 [pfBlockerNG] DNSBL Webserver stopped Aug 21 12:39:01 tail_pfb 22424 [pfBlockerNG] Firewall Filter Service stopped Aug 21 12:39:01 php_pfb 22989 [pfBlockerNG] filterlog daemon stopped Aug 21 12:39:01 lighttpd_pfb 26879 [pfBlockerNG] DNSBL Webserver started Aug 21 12:39:01 tail_pfb 28083 [pfBlockerNG] Firewall Filter Service started Aug 21 12:39:01 php_pfb 28887 [pfBlockerNG] filterlog daemon started Aug 21 12:39:01 php 31423 [pfBlockerNG] DNSBL parser daemon started Aug 21 12:39:27 vnstatd 16176 SIGTERM received, exiting. Aug 21 12:39:27 root 27425 Bootup complete Aug 21 12:39:29 login 67823 login on ttyv0 as root Aug 21 12:39:33 arpwatch 18794 bogon 0.0.0.0 fc:b4:67:d4:db:b0 Aug 21 12:39:33 arpwatch 18794 bogon 0.0.0.0 fc:b4:67:d4:db:b0 Aug 21 12:39:34 arpwatch 18794 bogon 0.0.0.0 fc:b4:67:d4:db:b0 ----------- TOGGLED WAN DOWN TO UP ------------ Aug 21 12:45:48 kernel vtnet1: link state changed to DOWN Aug 21 12:45:48 check_reload_status 428 Linkup starting vtnet1 Aug 21 12:45:49 php-fpm 397 /rc.linkup: Hotplug event detected for WAN(wan) dynamic IP address (4: dhcp) Aug 21 12:45:49 php-fpm 397 /rc.linkup: DEVD Ethernet detached event for wan Aug 21 12:45:50 check_reload_status 428 updating dyndns WAN_DHCP Aug 21 12:45:50 check_reload_status 428 Restarting IPsec tunnels Aug 21 12:45:50 check_reload_status 428 Restarting OpenVPN tunnels/interfaces Aug 21 12:45:50 check_reload_status 428 Reloading filter Aug 21 12:45:50 rc.gateway_alarm 13675 >>> Gateway alarm: WAN_DHCP (Addr:x.x.x.x Alarm:down RTT:0ms RTTsd:0ms Loss:100%) Aug 21 12:45:51 php-fpm 396 /rc.openvpn: The command '/sbin/route -n6 get 'default' 2>/dev/null | /usr/bin/egrep 'flags: <.*PROTO.*>'' returned exit code '1', the output was '' Aug 21 12:45:51 php-fpm 396 /rc.openvpn: OpenVPN: One or more OpenVPN tunnel endpoints may have changed IP addresses. Reloading endpoints that may use WAN_DHCP. Aug 21 12:45:53 check_reload_status 428 Linkup starting vtnet1 Aug 21 12:45:53 kernel vtnet1: link state changed to UP Aug 21 12:46:00 php-cgi 55521 servicewatchdog_cron.php: Service Watchdog detected service dpinger stopped. Restarting dpinger (Gateway Monitoring Daemon) Aug 21 12:46:00 php-cgi 57907 notify_monitor.php: Could not send the message to alert@xxxxxxx.com -- Error: Failed to connect to ssl://smtp.googlemail.com:465 [SMTP: Failed to connect socket: php_network_getaddresses: getaddrinfo for smtp.googlemail.com failed: Name does not resolve (code: -1, response: )] Aug 21 12:46:01 check_reload_status 428 Reloading filter Aug 21 12:46:01 php-fpm 396 /rc.linkup: Hotplug event detected for WAN(wan) dynamic IP address (4: dhcp) Aug 21 12:46:01 php-fpm 396 /rc.linkup: DEVD Ethernet attached event for wan Aug 21 12:46:01 php-fpm 396 /rc.linkup: HOTPLUG: Configuring interface wan Aug 21 12:46:01 php-fpm 396 /rc.linkup: The command '/sbin/ifconfig 'vtnet1' media 'autoselect'' returned exit code '1', the output was 'ifconfig: SIOCSIFMEDIA (media): Operation not supported' Aug 21 12:46:02 check_reload_status 428 rc.newwanip starting vtnet1 Aug 21 12:46:02 php-fpm 396 /rc.linkup: Default gateway setting Interface WAN_DHCP Gateway as default. Aug 21 12:46:02 php-fpm 396 /rc.linkup: The command '/sbin/route -n6 get 'default' 2>/dev/null | /usr/bin/egrep 'flags: <.*PROTO.*>'' returned exit code '1', the output was '' Aug 21 12:46:02 check_reload_status 428 Restarting IPsec tunnels Aug 21 12:46:03 php-fpm 397 /rc.newwanip: rc.newwanip: Info: starting on vtnet1. Aug 21 12:46:03 php-fpm 397 /rc.newwanip: rc.newwanip: on (IP address: x.x.x.x) (interface: WAN[wan]) (real interface: vtnet1). Aug 21 12:46:04 arpwatch 20902 bogon x.x.x.x d4:5a:3f:3c:db:09 Aug 21 12:46:12 kernel ovpnc2: link state changed to UP Aug 21 12:46:12 check_reload_status 428 rc.newwanip starting ovpnc2 Aug 21 12:46:13 php-fpm 907 /rc.newwanip: rc.newwanip: Info: starting on ovpnc2. Aug 21 12:46:13 php-fpm 907 /rc.newwanip: rc.newwanip: on (IP address: 10.16.0.2) (interface: PROTONVPN_NL[opt4]) (real interface: ovpnc2). Aug 21 12:46:37 php-fpm 397 /rc.newwanip: The command '/sbin/route -n6 get 'default' 2>/dev/null | /usr/bin/egrep 'flags: <.*PROTO.*>'' returned exit code '1', the output was '' Aug 21 12:46:37 php-fpm 397 /rc.newwanip: IP Address has changed, killing states on former IP Address 0.0.0.0. Aug 21 12:46:40 php-fpm 907 /rc.newwanip: The command '/sbin/route -n6 get 'default' 2>/dev/null | /usr/bin/egrep 'flags: <.*PROTO.*>'' returned exit code '1', the output was '' Aug 21 12:46:47 check_reload_status 428 updating dyndns wan Aug 21 12:46:47 check_reload_status 428 Reloading filter Aug 21 12:46:48 arpwatch 20902 bogon x.x.x.x d4:5a:3f:3c:db:09 Aug 21 12:47:16 php-fpm 397 /rc.newwanip: Resyncing OpenVPN instances for interface WAN. Aug 21 12:47:16 php-fpm 397 OpenVPN terminate old pid: 66100 Aug 21 12:47:16 kernel ovpns1: link state changed to DOWN Aug 21 12:47:19 pfSctl 64586 could not finish read in a reasonable time. Action of event might not be completed. Aug 21 12:47:20 php-fpm 397 /rc.newwanip: OpenVPN ID server1 PID 66100 still running, killing. Aug 21 12:47:20 php-fpm 397 OpenVPN PID written: 81805 Aug 21 12:47:20 kernel ovpns1: link state changed to UP Aug 21 12:47:22 check_reload_status 428 Reloading filter Aug 21 12:47:22 check_reload_status 428 Reloading filter Aug 21 12:47:22 check_reload_status 428 rc.newwanip starting ovpns1 Aug 21 12:47:22 php-fpm 397 OpenVPN terminate old pid: 83659 Aug 21 12:47:23 php-fpm 49815 /rc.newwanip: rc.newwanip: Info: starting on ovpns1. Aug 21 12:47:23 php-fpm 49815 /rc.newwanip: Interface is disabled, nothing to do. Aug 21 12:47:23 kernel ovpnc2: link state changed to DOWN Aug 21 12:47:23 check_reload_status 428 Reloading filter Aug 21 12:47:24 php-fpm 397 OpenVPN PID written: 24831 Aug 21 12:47:24 php-fpm 397 /rc.newwanip: Creating rrd update script Aug 21 12:47:26 kernel ovpnc2: link state changed to UP Aug 21 12:47:26 check_reload_status 428 rc.newwanip starting ovpnc2 Aug 21 12:47:26 php-fpm 397 /rc.newwanip: pfSense package system has detected an IP change or dynamic WAN reconnection - 0.0.0.0 -> x.x.x.x - Restarting packages. Aug 21 12:47:26 check_reload_status 428 Starting packages Aug 21 12:47:27 php-fpm 43380 /rc.newwanip: rc.newwanip: Info: starting on ovpnc2. Aug 21 12:47:27 php-fpm 43380 /rc.newwanip: rc.newwanip: on (IP address: 10.22.0.3) (interface: PROTONVPN_NL[opt4]) (real interface: ovpnc2). Aug 21 12:47:27 php-fpm 396 /rc.start_packages: Restarting/Starting all packages. Aug 21 12:47:38 rc.gateway_alarm 92417 >>> Gateway alarm: PROTONVPN_NL_VPNV4 (Addr:10.16.0.2 Alarm:1 RTT:8.006ms RTTsd:49.594ms Loss:21%) Aug 21 12:47:38 check_reload_status 428 updating dyndns PROTONVPN_NL_VPNV4 Aug 21 12:47:38 check_reload_status 428 Restarting IPsec tunnels Aug 21 12:47:38 check_reload_status 428 Restarting OpenVPN tunnels/interfaces Aug 21 12:47:38 check_reload_status 428 Reloading filter Aug 21 12:47:39 php-fpm 397 /rc.openvpn: The command '/sbin/route -n6 get 'default' 2>/dev/null | /usr/bin/egrep 'flags: <.*PROTO.*>'' returned exit code '1', the output was '' Aug 21 12:47:39 php-fpm 397 /rc.openvpn: OpenVPN: One or more OpenVPN tunnel endpoints may have changed IP addresses. Reloading endpoints that may use PROTONVPN_NL_VPNV4. Aug 21 12:47:52 php-fpm 907 /rc.newwanip: The command '/usr/local/sbin/unbound -c /var/unbound/unbound.conf' returned exit code '1', the output was '[1724240872] unbound[45808:0] error: bind: address already in use [1724240872] unbound[45808:0] fatal error: could not open ports' Aug 21 12:47:53 php-fpm 43380 /rc.newwanip: The command '/sbin/route -n6 get 'default' 2>/dev/null | /usr/bin/egrep 'flags: <.*PROTO.*>'' returned exit code '1', the output was '' Aug 21 12:47:53 php-fpm 43380 /rc.newwanip: IP Address has changed, killing states on former IP Address 10.16.0.2. Aug 21 12:47:53 php-fpm 907 /rc.newwanip: Creating rrd update script Aug 21 12:47:55 php-fpm 907 /rc.newwanip: pfSense package system has detected an IP change or dynamic WAN reconnection - 10.16.0.2 -> 10.16.0.2 - Restarting packages. Aug 21 12:48:00 check_reload_status 428 Starting packages Aug 21 12:48:00 check_reload_status 428 Reloading filter Aug 21 12:48:01 php-fpm 45571 /rc.start_packages: Skipping STARTing packages process because previous/another instance is already running Aug 21 12:48:31 php-fpm 43380 /rc.newwanip: Creating rrd update script Aug 21 12:48:33 kernel vtnet0.10: promiscuous mode disabled Aug 21 12:48:33 kernel vtnet1: promiscuous mode disabled Aug 21 12:48:33 kernel vtnet0.30: promiscuous mode disabled Aug 21 12:48:33 kernel vtnet0.20: promiscuous mode disabled Aug 21 12:48:33 kernel vtnet0.999: promiscuous mode disabled Aug 21 12:48:33 vnstatd 94480 vnStat daemon 2.11 (pid:94480 uid:0 gid:0, SQLite 3.43.1) Aug 21 12:48:33 vnstatd 94480 Data retention: 48 5MinuteHours, 4 HourlyDays, 62 DailyDays, 25 MonthlyMonths, -1 YearlyYears, 20 TopDayEntries Aug 21 12:48:33 vnstatd 94480 Monitoring (12): vtnet1 (10000 Mbit) vtnet0.999 (10000 Mbit) vtnet0.40 (10000 Mbit) vtnet0.30 (10000 Mbit) vtnet0.20 (10000 Mbit) vtnet0.10 (10000 Mbit) vtnet0 (10000 Mbit) pfsync0 (1000 Mbit) pflog0 (1000 Mbit) ovpns1 (1000 Mbit) ovpnc2 (1000 Mbit) enc0 (1000 Mbit) Aug 21 12:48:33 php-fpm 43380 /rc.newwanip: pfSense package system has detected an IP change or dynamic WAN reconnection - 10.16.0.2 -> 10.22.0.3 - Restarting packages. Aug 21 12:48:33 check_reload_status 428 Starting packages Aug 21 12:48:33 check_reload_status 428 Reloading filter Aug 21 12:48:34 php-fpm 397 /rc.start_packages: Skipping STARTing packages process because previous/another instance is already running Aug 21 12:48:36 arpwatch 33916 listening on vtnet0 Aug 21 12:48:36 kernel vtnet0.10: promiscuous mode enabled Aug 21 12:48:36 arpwatch 34087 listening on vtnet0.10 Aug 21 12:48:36 kernel vtnet0.20: promiscuous mode enabled Aug 21 12:48:36 arpwatch 34436 listening on vtnet0.20 Aug 21 12:48:36 arpwatch 35139 Link layer type 0 not ethernet or fddi Aug 21 12:48:36 kernel vtnet0.30: promiscuous mode enabled Aug 21 12:48:36 kernel ovpnc2: promiscuous mode enabled Aug 21 12:48:36 kernel ovpnc2: promiscuous mode disabled Aug 21 12:48:36 arpwatch 34681 listening on vtnet0.30 Aug 21 12:48:36 arpwatch 35875 pcap open : : No such device exists (No such device exists) Aug 21 12:48:36 kernel vtnet0.999: promiscuous mode enabled Aug 21 12:48:36 kernel vtnet1: promiscuous mode enabled Aug 21 12:48:36 arpwatch 35559 listening on vtnet0.999 Aug 21 12:48:36 arpwatch 35992 listening on vtnet1 Aug 21 12:48:43 vnstatd 94480 SIGTERM received, exiting. Aug 21 12:48:43 vnstatd 50165 vnStat daemon 2.11 (pid:50165 uid:0 gid:0, SQLite 3.43.1) Aug 21 12:48:43 vnstatd 50165 Data retention: 48 5MinuteHours, 4 HourlyDays, 62 DailyDays, 25 MonthlyMonths, -1 YearlyYears, 20 TopDayEntries Aug 21 12:48:43 vnstatd 50165 Monitoring (12): vtnet1 (10000 Mbit) vtnet0.999 (10000 Mbit) vtnet0.40 (10000 Mbit) vtnet0.30 (10000 Mbit) vtnet0.20 (10000 Mbit) vtnet0.10 (10000 Mbit) vtnet0 (10000 Mbit) pfsync0 (1000 Mbit) pflog0 (1000 Mbit) ovpns1 (1000 Mbit) ovpnc2 (1000 Mbit) enc0 (1000 Mbit) Aug 21 12:48:43 vnstatd 52656 Error: pidfile "/var/run/vnstat/vnstat.pid" lock failed (Resource temporarily unavailable), exiting. Aug 21 12:48:43 lighttpd_pfb 53425 [pfBlockerNG] DNSBL Webserver stopped Aug 21 12:48:43 tail_pfb 55087 [pfBlockerNG] Firewall Filter Service stopped Aug 21 12:48:43 php_pfb 55982 [pfBlockerNG] filterlog daemon stopped Aug 21 12:48:43 tail_pfb 58619 [pfBlockerNG] Firewall Filter Service started Aug 21 12:48:43 lighttpd_pfb 60520 [pfBlockerNG] DNSBL Webserver started Aug 21 12:48:43 php_pfb 59060 [pfBlockerNG] filterlog daemon started Aug 21 12:48:43 php 61611 [pfBlockerNG] DNSBL parser daemon started Aug 21 12:49:00 php-cgi 67732 servicewatchdog_cron.php: Service Watchdog detected service telegraf stopped. Restarting telegraf (Telegraf daemon) Aug 21 12:49:06 php-cgi 70303 notify_monitor.php: Message sent to alert@xxxxxx.com OK Aug 21 12:50:00 php-fpm 45571 /status_logs.php: Configuration Change: admin@192.168.2.21 (Local Database): Log Display Settings Saved (no backup, no sync): General -
@randombits said in WAN only connects on unplug and plug back in:
Aug 21 12:37:54 php-cgi 453 rc.bootup: The command '/sbin/ifconfig 'vtnet1' inet6 delete' returned exit code '1', the output was 'ifconfig: ioctl (SIOCDIFADDR): Can't assign requested address'
Just spotted this I wonder if it's a issue ?
-
Unlikely, it probably doesn't have an IPv6 address.
Which pfSense version is this?
-
@stephenw10 I just remembered I did briefly enable IPv6 in the WAN basically to see if it would pick up an address from my ISP it did. But I undid it. I'm using version
pfSense CE version 2.7.2-RELEASE (amd64) built on Wed Dec 6 20:10:00 GMT 2023 FreeBSD 14.0-CURRENT -
Hmm what do you see if you run?:
[2.7.2-RELEASE][admin@cedev-6.stevew.lan]/root: /sbin/route -n6 get 'default' route: route has not been found: No error: 0For some reason that is returning 1 for you during bootup which is probably preventing the rest of the script running.
-
@stephenw10 When it's working ok the same as you
[2.7.2-RELEASE][root@pfSense.localdomain]/root: /sbin/route -n6 get 'default' route: route has not been found: No error: 0I need to wait a bit before I can reboot and take the internet down as I'm up and downloading....
Just rebooted and it's the (no internet)
[2.7.2-RELEASE][root@pfSense.localdomain]/root: /sbin/route -n6 get 'default' route: route has not been found: No error: 0 -
OK, so that's the no default IPv4 route situation?
-
@stephenw10 indeed, until WAN up-down
-
Hmm, curious. Try setting the IPv6 default gateway to something, WAN_DHCPv6 for example. That should remove the error at least.
-
@stephenw10 Well, As a sanity(in) check I installed another pfSense (VM) and lo and behold that has the same issue !
What I have is Proxmox with a single ethernet port with Proxmox provides the two NIC's for pfSense, the WAN NIC is on vlan 1000 and the switch splits that of into to ports. The ONT port is untagged 1000 solely (no vlan 1 internal to the switch) and LAN and other vlans are on one of the other ports
g1 Trunk 1 1U g2 Trunk 1 1U g3 Trunk 1 1U g4 Trunk 1 1U g5 Trunk 1 1U,10T,20T,999T g6 Trunk 1 1U,10T,20T,999T,1000T g7 Access 1000 1000U g8 Trunk 1 1U,10T,20T,999T Switch ports 1 - 1U 2 - 1U 3 - 1U 4 SPA 1U 5 AP 1U,10T,20T,999T 6 Server 1U,10T,20T,999T,1000T 7 Modem 1000U 8 - 1U,10T,20T,999T
