Netgate Discussion Forum
    • Categories
    • Recent
    • Tags
    • Popular
    • Users
    • Search
    • Register
    • Login

    pfSense not enabling port

    General pfSense Questions
    4
    145
    9.2k
    Loading More Posts
    • Oldest to Newest
    • Newest to Oldest
    • Most Votes
    Reply
    • Reply as topic
    Log in to reply
    This topic has been deleted. Only users with topic management privileges can see it.
    • georgelzaG
      georgelza @Gblenn
      last edited by

      @Gblenn

      after the above.

      what i have noticed though, my port on the switch has gone red, complaining of packet loss etc.
      wonder if we need to go back to auto negotiate.
      ip a
      i did have to bring the interfaces up, both the vlan30 that sits on vmbr0 and vmbr40 was down.

      1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default qlen 1000
    link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
    inet 127.0.0.1/8 scope host lo
       valid_lft forever preferred_lft forever
    inet6 ::1/128 scope host noprefixroute
       valid_lft forever preferred_lft forever
2: enp2s0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq master vmbr0 state UP group default qlen 1000
    link/ether a8:b8:e0:02:a3:71 brd ff:ff:ff:ff:ff:ff
3: enp3s0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN group default qlen 1000
    link/ether a8:b8:e0:02:a3:72 brd ff:ff:ff:ff:ff:ff
4: enp5s0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN group default qlen 1000
    link/ether a8:b8:e0:02:a3:73 brd ff:ff:ff:ff:ff:ff
5: enp6s0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN group default qlen 1000
    link/ether a8:b8:e0:02:a3:74 brd ff:ff:ff:ff:ff:ff
8: vmbr0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP group default qlen 1000
    link/ether a8:b8:e0:02:a3:71 brd ff:ff:ff:ff:ff:ff
    inet 172.16.10.50/24 scope global vmbr0
       valid_lft forever preferred_lft forever
    inet6 fe80::aab8:e0ff:fe02:a371/64 scope link
       valid_lft forever preferred_lft forever
9: vmbr40: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP group default qlen 1000
    link/ether a8:b8:e0:05:f0:91 brd ff:ff:ff:ff:ff:ff
    inet6 fe80::aab8:e0ff:fe05:f091/64 scope link
       valid_lft forever preferred_lft forever
10: tap100i0: <BROADCAST,MULTICAST,PROMISC,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast master fwbr100i0 state UNKNOWN group default qlen 1000
    link/ether c6:2d:5a:7a:41:d7 brd ff:ff:ff:ff:ff:ff
11: fwbr100i0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP group default qlen 1000
    link/ether da:0c:52:e1:39:89 brd ff:ff:ff:ff:ff:ff
12: fwpr100p0@fwln100i0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue master vmbr0 state UP group default qlen 1000
    link/ether 76:c4:56:d3:6a:93 brd ff:ff:ff:ff:ff:ff
13: fwln100i0@fwpr100p0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue master fwbr100i0 state UP group default qlen 1000
    link/ether da:0c:52:e1:39:89 brd ff:ff:ff:ff:ff:ff
14: tap100i1: <BROADCAST,MULTICAST,PROMISC,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast master fwbr100i1 state UNKNOWN group default qlen 1000
    link/ether 76:c9:86:22:cc:30 brd ff:ff:ff:ff:ff:ff
15: fwbr100i1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP group default qlen 1000
    link/ether 52:9a:1c:4d:76:a6 brd ff:ff:ff:ff:ff:ff
16: fwpr100p1@fwln100i1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue master vmbr0 state UP group default qlen 1000
    link/ether 26:2d:af:5a:9a:b4 brd ff:ff:ff:ff:ff:ff
17: fwln100i1@fwpr100p1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue master fwbr100i1 state UP group default qlen 1000
    link/ether 52:9a:1c:4d:76:a6 brd ff:ff:ff:ff:ff:ff
18: tap100i2: <BROADCAST,MULTICAST,PROMISC,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast master fwbr100i2 state UNKNOWN group default qlen 1000
    link/ether c2:9f:1f:4e:c6:2e brd ff:ff:ff:ff:ff:ff
19: fwbr100i2: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP group default qlen 1000
    link/ether 7a:a8:67:a9:29:14 brd ff:ff:ff:ff:ff:ff
20: fwpr100p2@fwln100i2: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue master vmbr40 state UP group default qlen 1000
    link/ether 72:43:cc:4b:b3:40 brd ff:ff:ff:ff:ff:ff
21: fwln100i2@fwpr100p2: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue master fwbr100i2 state UP group default qlen 1000
    link/ether 7a:a8:67:a9:29:14 brd ff:ff:ff:ff:ff:ff
22: vlan30@vmbr0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP group default qlen 1000
    link/ether a8:b8:e0:02:a3:71 brd ff:ff:ff:ff:ff:ff
    inet6 fe80::aab8:e0ff:fe02:a371/64 scope link
       valid_lft forever preferred_lft forever
23: enp4s0f0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN group default qlen 1000
    link/ether a8:b8:e0:05:f0:91 brd ff:ff:ff:ff:ff:ff
24: enp4s0f1: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN group default qlen 1000
    link/ether a8:b8:e0:05:f0:92 brd ff:ff:ff:ff:ff:ff

      dmesg | grep ixgbe

      [19185.217533] ixgbe 0000:04:00.0 enp4s0f0: NIC Link is Up 10 Gbps, Flow Control: RX/TX
[19185.321424] ixgbe 0000:04:00.0 enp4s0f0: NIC Link is Down
[19185.529459] ixgbe 0000:04:00.0 enp4s0f0: NIC Link is Up 10 Gbps, Flow Control: RX/TX
[19185.633445] ixgbe 0000:04:00.0 enp4s0f0: NIC Link is Down
[19185.862491] ixgbe 0000:04:00.1: complete
[19185.862751] ixgbe 0000:04:00.0: removed PHC on enp4s0f0
[19185.922172] ixgbe 0000:04:00.0 enp4s0f0 (unregistering): left allmulticast mode
[19185.922174] ixgbe 0000:04:00.0 enp4s0f0 (unregistering): left promiscuous mode
[19185.984591] ixgbe 0000:04:00.0: complete
[19186.014865] ixgbe: Intel(R) 10 Gigabit PCI Express Network Driver
[19186.014867] ixgbe: Copyright (c) 1999-2016 Intel Corporation.
[19186.183424] ixgbe 0000:04:00.0: Multiqueue Enabled: Rx Queue count = 12, Tx Queue count = 12 XDP Queue count = 0
[19186.183731] ixgbe 0000:04:00.0: 16.000 Gb/s available PCIe bandwidth, limited by 5.0 GT/s PCIe x4 link at 0000:00:1c.4 (capable of 32.000 Gb/s with 5.0 GT/s PCIe x8 link)
[19186.183816] ixgbe 0000:04:00.0: MAC: 2, PHY: 19, SFP+: 5, PBA No: FFFFFF-0FF
[19186.183817] ixgbe 0000:04:00.0: a8:b8:e0:05:f0:91
[19186.184842] ixgbe 0000:04:00.0: Intel(R) 10 Gigabit Network Connection
[19186.195416] ixgbe 0000:04:00.0 enp4s0f0: renamed from eth0
[19187.336359] ixgbe 0000:04:00.1: Multiqueue Enabled: Rx Queue count = 12, Tx Queue count = 12 XDP Queue count = 0
[19187.336664] ixgbe 0000:04:00.1: 16.000 Gb/s available PCIe bandwidth, limited by 5.0 GT/s PCIe x4 link at 0000:00:1c.4 (capable of 32.000 Gb/s with 5.0 GT/s PCIe x8 link)
[19187.336749] ixgbe 0000:04:00.1: MAC: 2, PHY: 1, PBA No: FFFFFF-0FF
[19187.336750] ixgbe 0000:04:00.1: a8:b8:e0:05:f0:92
[19187.337749] ixgbe 0000:04:00.1: Intel(R) 10 Gigabit Network Connection
[19187.353403] ixgbe 0000:04:00.1 enp4s0f1: renamed from eth0
      georgelzaG 1 Reply Last reply Reply Quote 0
      • georgelzaG
        georgelza @georgelza
        last edited by

        on my switch side i run

        172.16.10.0/24 as my primary on the physical port
        then have the following vlans defined atm
        (running on the same above physical port)
        vlan20 - 172.16.20.0/24 -> all wifi devices
        vlan30 - 172.16.30.0/24 -> will be "vmotion/k8s cluster interconnect"

        vlan40 - 172.16.40.0/24 -> will be storage/io to be used by all to access the TrueNAS. 10GbE based on dedicated port.

        i've configured vmbr0 and vmbr40.
        i ended configuring vlan30 as a vlan on vmbr0.

        G

        G 1 Reply Last reply Reply Quote 0
        • G
          Gblenn @georgelza
          last edited by

          @georgelza Did you unplug the module from the SPF+ port on the Proxmox machine? What happens if you plug it in again, only the Proxmox side and leave the switch side hanging. Anything new that shows up from dmesg?

          georgelzaG 1 Reply Last reply Reply Quote 0
          • georgelzaG
            georgelza @Gblenn
            last edited by

            @Gblenn

            did not touch the physical side.

            i've since rechecked the switch and reset to manual and redefined it as 10GbE DFX

            re-issued the ethtool command on the pmox level.

            G

            georgelzaG 1 Reply Last reply Reply Quote 0
            • georgelzaG
              georgelza @georgelza
              last edited by georgelza

              @georgelza

              ok, got it back active on the switch.

              noticed that in pmox under network it was active=no, switched it to autostart and it seemed to have figured out to start itself.

              G

              root@ubuntu-01:~# ifconfig -a
docker0: flags=4099<UP,BROADCAST,MULTICAST>  mtu 1500
        inet 172.17.0.1  netmask 255.255.0.0  broadcast 172.17.255.255
        ether 02:42:cb:d9:fb:26  txqueuelen 0  (Ethernet)
        RX packets 0  bytes 0 (0.0 B)
        RX errors 0  dropped 0  overruns 0  frame 0
        TX packets 0  bytes 0 (0.0 B)
        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0

ens18: flags=4163<UP,BROADCAST,RUNNING,MULTICAST>  mtu 1500
        inet 172.16.10.51  netmask 255.255.255.0  broadcast 172.16.10.255
        inet6 fe80::be24:11ff:fec0:e81e  prefixlen 64  scopeid 0x20<link>
        ether bc:24:11:c0:e8:1e  txqueuelen 1000  (Ethernet)
        RX packets 124398  bytes 94163032 (94.1 MB)
        RX errors 0  dropped 64  overruns 0  frame 0
        TX packets 22096  bytes 2425895 (2.4 MB)
        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0

ens19: flags=4163<UP,BROADCAST,RUNNING,MULTICAST>  mtu 1500
        inet6 fe80::be24:11ff:fe81:2ccb  prefixlen 64  scopeid 0x20<link>
        ether bc:24:11:81:2c:cb  txqueuelen 1000  (Ethernet)
        RX packets 22  bytes 1566 (1.5 KB)
        RX errors 0  dropped 0  overruns 0  frame 0
        TX packets 15  bytes 1146 (1.1 KB)
        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0

ens20: flags=4163<UP,BROADCAST,RUNNING,MULTICAST>  mtu 1500
        inet6 fe80::be24:11ff:fe1e:20ac  prefixlen 64  scopeid 0x20<link>
        ether bc:24:11:1e:20:ac  txqueuelen 1000  (Ethernet)
        RX packets 0  bytes 0 (0.0 B)
        RX errors 0  dropped 0  overruns 0  frame 0
        TX packets 15  bytes 1146 (1.1 KB)
        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0

lo: flags=73<UP,LOOPBACK,RUNNING>  mtu 65536
        inet 127.0.0.1  netmask 255.0.0.0
        inet6 ::1  prefixlen 128  scopeid 0x10<host>
        loop  txqueuelen 1000  (Local Loopback)
        RX packets 128  bytes 11444 (11.4 KB)
        RX errors 0  dropped 0  overruns 0  frame 0
        TX packets 128  bytes 11444 (11.4 KB)
        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0

root@ubuntu-01:~

              ip a

              root@ubuntu-01:~# ip a
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default qlen 1000
    link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
    inet 127.0.0.1/8 scope host lo
       valid_lft forever preferred_lft forever
    inet6 ::1/128 scope host
       valid_lft forever preferred_lft forever
2: ens18: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc fq_codel state UP group default qlen 1000
    link/ether bc:24:11:c0:e8:1e brd ff:ff:ff:ff:ff:ff
    inet 172.16.10.51/24 metric 100 brd 172.16.10.255 scope global dynamic ens18
       valid_lft 5917sec preferred_lft 5917sec
    inet6 fe80::be24:11ff:fec0:e81e/64 scope link
       valid_lft forever preferred_lft forever
3: ens19: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc fq_codel state UP group default qlen 1000
    link/ether bc:24:11:81:2c:cb brd ff:ff:ff:ff:ff:ff
    inet6 fe80::be24:11ff:fe81:2ccb/64 scope link
       valid_lft forever preferred_lft forever
4: ens20: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc fq_codel state UP group default qlen 1000
    link/ether bc:24:11:1e:20:ac brd ff:ff:ff:ff:ff:ff
    inet6 fe80::be24:11ff:fe1e:20ac/64 scope link
       valid_lft forever preferred_lft forever
5: docker0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc noqueue state DOWN group default
    link/ether 02:42:cb:d9:fb:26 brd ff:ff:ff:ff:ff:ff
    inet 172.17.0.1/16 brd 172.17.255.255 scope global docker0
       valid_lft forever preferred_lft forever
root@ubuntu-01:~#

              dmesg, flapping again

              [23193.684199] ixgbe 0000:04:00.0 enp4s0f0: NIC Link is Down
[23196.284232] ixgbe 0000:04:00.0 enp4s0f0: NIC Link is Up 10 Gbps, Flow Control: RX/TX
[23196.492219] ixgbe 0000:04:00.0 enp4s0f0: NIC Link is Down
[23196.700248] ixgbe 0000:04:00.0 enp4s0f0: NIC Link is Up 10 Gbps, Flow Control: RX/TX
[23196.804186] ixgbe 0000:04:00.0 enp4s0f0: NIC Link is Down
[23197.012247] ixgbe 0000:04:00.0 enp4s0f0: NIC Link is Up 10 Gbps, Flow Control: RX/TX
[23197.116191] ixgbe 0000:04:00.0 enp4s0f0: NIC Link is Down
[23197.325189] ixgbe 0000:04:00.0 enp4s0f0: NIC Link is Up 10 Gbps, Flow Control: RX/TX
[23197.428371] ixgbe 0000:04:00.0 enp4s0f0: NIC Link is Down
[23199.924253] ixgbe 0000:04:00.0 enp4s0f0: NIC Link is Up 10 Gbps, Flow Control: RX/TX
[23200.028227] ixgbe 0000:04:00.0 enp4s0f0: NIC Link is Down
[23200.756251] ixgbe 0000:04:00.0 enp4s0f0: NIC Link is Up 10 Gbps, Flow Control: RX/TX
[23200.860223] ixgbe 0000:04:00.0 enp4s0f0: NIC Link is Down
[23200.964189] ixgbe 0000:04:00.0 enp4s0f0: NIC Link is Up 10 Gbps, Flow Control: RX/TX
[23201.068135] ixgbe 0000:04:00.0 enp4s0f0: NIC Link is Down
[23201.172183] ixgbe 0000:04:00.0 enp4s0f0: NIC Link is Up 10 Gbps, Flow Control: RX/TX
[23201.276115] ixgbe 0000:04:00.0 enp4s0f0: NIC Link is Down
[23201.484251] ixgbe 0000:04:00.0 enp4s0f0: NIC Link is Up 10 Gbps, Flow Control: RX/TX
[23201.588222] ixgbe 0000:04:00.0 enp4s0f0: NIC Link is Down
[23203.668163] ixgbe 0000:04:00.0 enp4s0f0: NIC Link is Up 10 Gbps, Flow Control: RX/TX
[23203.772131] ixgbe 0000:04:00.0 enp4s0f0: NIC Link is Down
[23204.916258] ixgbe 0000:04:00.0 enp4s0f0: NIC Link is Up 10 Gbps, Flow Control: RX/TX
[23205.020120] ixgbe 0000:04:00.0 enp4s0f0: NIC Link is Down
[23205.228162] ixgbe 0000:04:00.0 enp4s0f0: NIC Link is Up 10 Gbps, Flow Control: RX/TX
[23205.332137] ixgbe 0000:04:00.0 enp4s0f0: NIC Link is Down
[23205.540156] ixgbe 0000:04:00.0 enp4s0f0: NIC Link is Up 10 Gbps, Flow Control: RX/TX
[23205.644121] ixgbe 0000:04:00.0 enp4s0f0: NIC Link is Down
[23205.748154] ixgbe 0000:04:00.0 enp4s0f0: NIC Link is Up 10 Gbps, Flow Control: RX/TX
[23205.956212] ixgbe 0000:04:00.0 enp4s0f0: NIC Link is Down
[23206.060156] ixgbe 0000:04:00.0 enp4s0f0: NIC Link is Up 10 Gbps, Flow Control: RX/TX
[23206.268107] ixgbe 0000:04:00.0 enp4s0f0: NIC Link is Down

              then issued the ethtool command, which made my switch port go red.

              then dmesg changed to

              [23352.570211] ixgbe 0000:04:00.0: complete
[23352.608227] ixgbe: Intel(R) 10 Gigabit PCI Express Network Driver
[23352.608229] ixgbe: Copyright (c) 1999-2016 Intel Corporation.
[23352.776181] ixgbe 0000:04:00.0: Multiqueue Enabled: Rx Queue count = 12, Tx Queue count = 12 XDP Queue count = 0
[23352.776488] ixgbe 0000:04:00.0: 16.000 Gb/s available PCIe bandwidth, limited by 5.0 GT/s PCIe x4 link at 0000:00:1c.4 (capable of 32.000 Gb/s with 5.0 GT/s PCIe x8 link)
[23352.776573] ixgbe 0000:04:00.0: MAC: 2, PHY: 19, SFP+: 5, PBA No: FFFFFF-0FF
[23352.776574] ixgbe 0000:04:00.0: a8:b8:e0:05:f0:91
[23352.777559] ixgbe 0000:04:00.0: Intel(R) 10 Gigabit Network Connection
[23352.785028] ixgbe 0000:04:00.0 enp4s0f0: renamed from eth0
[23353.930084] ixgbe 0000:04:00.1: Multiqueue Enabled: Rx Queue count = 12, Tx Queue count = 12 XDP Queue count = 0
[23353.930388] ixgbe 0000:04:00.1: 16.000 Gb/s available PCIe bandwidth, limited by 5.0 GT/s PCIe x4 link at 0000:00:1c.4 (capable of 32.000 Gb/s with 5.0 GT/s PCIe x8 link)
[23353.930472] ixgbe 0000:04:00.1: MAC: 2, PHY: 1, PBA No: FFFFFF-0FF
[23353.930473] ixgbe 0000:04:00.1: a8:b8:e0:05:f0:92
[23353.931466] ixgbe 0000:04:00.1: Intel(R) 10 Gigabit Network Connection
[23353.947017] ixgbe 0000:04:00.1 enp4s0f1: renamed from eth0
[23367.436987] ixgbe 0000:04:00.1: complete
[23367.446889] ixgbe 0000:04:00.0: complete
[23367.483630] ixgbe: Intel(R) 10 Gigabit PCI Express Network Driver
[23367.483632] ixgbe: Copyright (c) 1999-2016 Intel Corporation.
[23367.652922] ixgbe 0000:04:00.0: Multiqueue Enabled: Rx Queue count = 12, Tx Queue count = 12 XDP Queue count = 0
[23367.653228] ixgbe 0000:04:00.0: 16.000 Gb/s available PCIe bandwidth, limited by 5.0 GT/s PCIe x4 link at 0000:00:1c.4 (capable of 32.000 Gb/s with 5.0 GT/s PCIe x8 link)
[23367.653313] ixgbe 0000:04:00.0: MAC: 2, PHY: 19, SFP+: 5, PBA No: FFFFFF-0FF
[23367.653314] ixgbe 0000:04:00.0: a8:b8:e0:05:f0:91
[23367.654319] ixgbe 0000:04:00.0: Intel(R) 10 Gigabit Network Connection
[23367.662770] ixgbe 0000:04:00.0 enp4s0f0: renamed from eth0
[23368.800920] ixgbe 0000:04:00.1: Multiqueue Enabled: Rx Queue count = 12, Tx Queue count = 12 XDP Queue count = 0
[23368.801226] ixgbe 0000:04:00.1: 16.000 Gb/s available PCIe bandwidth, limited by 5.0 GT/s PCIe x4 link at 0000:00:1c.4 (capable of 32.000 Gb/s with 5.0 GT/s PCIe x8 link)
[23368.801311] ixgbe 0000:04:00.1: MAC: 2, PHY: 1, PBA No: FFFFFF-0FF
[23368.801311] ixgbe 0000:04:00.1: a8:b8:e0:05:f0:92
[23368.802549] ixgbe 0000:04:00.1: Intel(R) 10 Gigabit Network Connection
[23368.812911] ixgbe 0000:04:00.1 enp4s0f1: renamed from eth0
              1 Reply Last reply Reply Quote 0
              • georgelzaG
                georgelza
                last edited by

                thinking need to figure out how to address the port...

                tried

                options ixgbe allow_unsupported_sfp=1
                and
                options ixgbe allow_unsupported_sfp=1.1
                and
                options ixgbe allow_unsupported_sfp=0.1
                and
                options ixgbe allow_unsupported_sfp=0.0

                1 Reply Last reply Reply Quote 0
                • georgelzaG
                  georgelza
                  last edited by georgelza

                  i'm starting to question if the 10GbE is actually up...
                  i'm thinking when i ping the gw from pmox or the ubuntu-01 image it actually goes out the default gw over the vmbr0 bridge. and not out via the SFP+

                  for some reason i'm also not getting a ip on vlan30 on the guest vm, vlan30 runs over vmbr0

                  well let me add... if i make some changes on the pmox side it does break the switch side so the physical link is there, and there is some level of comm, or is that disagreement.

                  G

                  1 Reply Last reply Reply Quote 0
                  • georgelzaG
                    georgelza
                    last edited by

                    note to self, when de-configuring something to check something... dont reconfigure your main/only interface... especially if machines are 10foot of the ground on a shelve with no Kvm in place. ;)

                    can confirm that the green and orange light on the SFP+ port is having a party, matching on switch is just flickering red.

                    G

                    1 Reply Last reply Reply Quote 0
                    • stephenw10S
                      stephenw10 Netgate Administrator
                      last edited by

                      @Gblenn said in pfSense not enabling port:

                      ixgbe allow_unsupported_sfp=1

                      The allow_unsupported option can only be 1 or 0, it's on or off. It applies to all ixgbe attached devices applied there.

                      Nothing posted here so far looks like it's linking correctly to me.

                      Did you ever try just linking the two SFP+ ports directly to see if it would link up and be stable?

                      georgelzaG 1 Reply Last reply Reply Quote 0
                      • georgelzaG
                        georgelza
                        last edited by

                        ok... my assumption confirmed...

                        even though there is light travelling down the fiber link it's not working.

                        the pings was going out the default gw.

                        i disabled the vlan0/172.16.10.51 interface on ubuntu-01 and tried to ping out on all networks, all failed, the second i re-enabled it all worked.

                        G

                        1 Reply Last reply Reply Quote 0
                        • georgelzaG
                          georgelza @stephenw10
                          last edited by

                          @stephenw10 said in pfSense not enabling port:

                          Did you ever try just linking the two SFP+ ports directly to see if it would link up and be stable?

                          explain.

                          ok, corrected mod_probe, set to =1.
                          executed the reload.

                          below is the output, port on switch has gone red now.
                          wondering if it might sense to get the port and the interface to be back on auto negotiate.

                          G

                          [31585.664382] ixgbe 0000:04:00.0 enp4s0f0: NIC Link is Up 10 Gbps, Flow Control: RX/TX
[31585.769298] ixgbe 0000:04:00.0 enp4s0f0: NIC Link is Down
[31585.873330] ixgbe 0000:04:00.0 enp4s0f0: NIC Link is Up 10 Gbps, Flow Control: RX/TX
[31585.888669] ixgbe 0000:04:00.1: complete
[31585.889282] ixgbe 0000:04:00.0: removed PHC on enp4s0f0
[31585.949971] ixgbe 0000:04:00.0 enp4s0f0 (unregistering): left allmulticast mode
[31585.949974] ixgbe 0000:04:00.0 enp4s0f0 (unregistering): left promiscuous mode
[31586.012658] ixgbe 0000:04:00.0: complete
[31586.041780] ixgbe: Intel(R) 10 Gigabit PCI Express Network Driver
[31586.041782] ixgbe: Copyright (c) 1999-2016 Intel Corporation.
[31586.217345] ixgbe 0000:04:00.0: Multiqueue Enabled: Rx Queue count = 12, Tx Queue count = 12 XDP Queue count = 0
[31586.217650] ixgbe 0000:04:00.0: 16.000 Gb/s available PCIe bandwidth, limited by 5.0 GT/s PCIe x4 link at 0000:00:1c.4 (capable of 32.000 Gb/s with 5.0 GT/s PCIe x8 link)
[31586.217734] ixgbe 0000:04:00.0: MAC: 2, PHY: 19, SFP+: 5, PBA No: FFFFFF-0FF
[31586.217735] ixgbe 0000:04:00.0: a8:b8:e0:05:f0:91
[31586.218736] ixgbe 0000:04:00.0: Intel(R) 10 Gigabit Network Connection
[31586.234395] ixgbe 0000:04:00.0 enp4s0f0: renamed from eth0
[31587.366524] ixgbe 0000:04:00.1: Multiqueue Enabled: Rx Queue count = 12, Tx Queue count = 12 XDP Queue count = 0
[31587.366829] ixgbe 0000:04:00.1: 16.000 Gb/s available PCIe bandwidth, limited by 5.0 GT/s PCIe x4 link at 0000:00:1c.4 (capable of 32.000 Gb/s with 5.0 GT/s PCIe x8 link)
[31587.366913] ixgbe 0000:04:00.1: MAC: 2, PHY: 1, PBA No: FFFFFF-0FF
[31587.366914] ixgbe 0000:04:00.1: a8:b8:e0:05:f0:92
[31587.367921] ixgbe 0000:04:00.1: Intel(R) 10 Gigabit Network Connection
[31587.378331] ixgbe 0000:04:00.1 enp4s0f1: renamed from eth0
                          georgelzaG stephenw10S 2 Replies Last reply Reply Quote 0
                          • georgelzaG
                            georgelza @georgelza
                            last edited by

                            :(

                            disabled auto negotiate on interface,

                            did a if reload -a

                            dmesg results in flapping again. port on switch has gone from red to grey/no errors.

                            [31747.031303] ixgbe 0000:04:00.0 enp4s0f0: NIC Link is Up 10 Gbps, Flow Control: RX/TX
[31747.135279] ixgbe 0000:04:00.0 enp4s0f0: NIC Link is Down
[31748.071313] ixgbe 0000:04:00.0 enp4s0f0: NIC Link is Up 10 Gbps, Flow Control: RX/TX
[31748.279274] ixgbe 0000:04:00.0 enp4s0f0: NIC Link is Down
[31749.007315] ixgbe 0000:04:00.0 enp4s0f0: NIC Link is Up 10 Gbps, Flow Control: RX/TX
[31749.111264] ixgbe 0000:04:00.0 enp4s0f0: NIC Link is Down
[31751.815311] ixgbe 0000:04:00.0 enp4s0f0: NIC Link is Up 10 Gbps, Flow Control: RX/TX
[31751.919316] ixgbe 0000:04:00.0 enp4s0f0: NIC Link is Down
[31752.439315] ixgbe 0000:04:00.0 enp4s0f0: NIC Link is Up 10 Gbps, Flow Control: RX/TX
[31752.543250] ixgbe 0000:04:00.0 enp4s0f0: NIC Link is Down
[31752.751293] ixgbe 0000:04:00.0 enp4s0f0: NIC Link is Up 10 Gbps, Flow Control: RX/TX
[31752.855259] ixgbe 0000:04:00.0 enp4s0f0: NIC Link is Down
[31753.167301] ixgbe 0000:04:00.0 enp4s0f0: NIC Link is Up 10 Gbps, Flow Control: RX/TX
[31753.271254] ixgbe 0000:04:00.0 enp4s0f0: NIC Link is Down
[31753.895300] ixgbe 0000:04:00.0 enp4s0f0: NIC Link is Up 10 Gbps, Flow Control: RX/TX
[31753.999229] ixgbe 0000:04:00.0 enp4s0f0: NIC Link is Down
[31754.935184] ixgbe 0000:04:00.0 enp4s0f0: NIC Link is Up 10 Gbps, Flow Control: RX/TX
[31755.039143] ixgbe 0000:04:00.0 enp4s0f0: NIC Link is Down
[31756.287172] ixgbe 0000:04:00.0 enp4s0f0: NIC Link is Up 10 Gbps, Flow Control: RX/TX
[31756.391041] ixgbe 0000:04:00.0 enp4s0f0: NIC Link is Down
[31758.055259] ixgbe 0000:04:00.0 enp4s0f0: NIC Link is Up 10 Gbps, Flow Control: RX/TX
[31758.159230] ixgbe 0000:04:00.0 enp4s0f0: NIC Link is Down
[31761.591166] ixgbe 0000:04:00.0 enp4s0f0: NIC Link is Up 10 Gbps, Flow Control: RX/TX
[31761.695076] ixgbe 0000:04:00.0 enp4s0f0: NIC Link is Down
[31761.903216] ixgbe 0000:04:00.0 enp4s0f0: NIC Link is Up 10 Gbps, Flow Control: RX/TX
[31762.007245] ixgbe 0000:04:00.0 enp4s0f0: NIC Link is Down
[31762.215038] ixgbe 0000:04:00.0 enp4s0f0: NIC Link is Up 10 Gbps, Flow Control: RX/TX
[31762.319061] ixgbe 0000:04:00.0 enp4s0f0: NIC Link is Down
[31762.943117] ixgbe 0000:04:00.0 enp4s0f0: NIC Link is Up 10 Gbps, Flow Control: RX/TX
[31763.047212] ixgbe 0000:04:00.0 enp4s0f0: NIC Link is Down
[31764.503186] ixgbe 0000:04:00.0 enp4s0f0: NIC Link is Up 10 Gbps, Flow Control: RX/TX
[31764.607154] ixgbe 0000:04:00.0 enp4s0f0: NIC Link is Down
[31764.919363] ixgbe 0000:04:00.0 enp4s0f0: NIC Link is Up 10 Gbps, Flow Control: RX/TX
[31765.023138] ixgbe 0000:04:00.0 enp4s0f0: NIC Link is Down
[31765.127138] ixgbe 0000:04:00.0 enp4s0f0: NIC Link is Up 10 Gbps, Flow Control: RX/TX
[31765.231280] ixgbe 0000:04:00.0 enp4s0f0: NIC Link is Down
                            1 Reply Last reply Reply Quote 0
                            • georgelzaG
                              georgelza
                              last edited by georgelza

                              just tried something, disabled the vmbr40 bridge, by removing the physical device.

                              configured a ip directly onto physical device.

                              can't ping the 172.16.40.1 gw.

                              it's saying no_carrier when i do a

                              ip a

                              G

                              1 Reply Last reply Reply Quote 0
                              • stephenw10S
                                stephenw10 Netgate Administrator @georgelza
                                last edited by

                                @georgelza said in pfSense not enabling port:

                                explain.

                                I mean just link the two SFP ports on the Topton together to see if it will link without flapping. You obviously won't be able to pass any traffic but if it shows a stable link on both ports in that situation it's probably some low level issue between the ix ports and the switch.

                                Though thinking more you could set that up in proxmox so you could pass traffic between them by having them on separate bridges.

                                georgelzaG 1 Reply Last reply Reply Quote 1
                                • georgelzaG
                                  georgelza @stephenw10
                                  last edited by

                                  @stephenw10 will try tomorrow.

                                  received a package bout 30min, ago, havent opened it, but think it could be the DAC cable and the 2nd Transceiver.

                                  G

                                  1 Reply Last reply Reply Quote 1
                                  • georgelzaG
                                    georgelza
                                    last edited by georgelza

                                    Ran the following on the pfSense host:

                                     pciconf -lcv ix0

ix0@pci0:4:0:0:	class=0x020000 rev=0x01 hdr=0x00 vendor=0x8086 device=0x10fb subvendor=0xffff subdevice=0xffff
    vendor     = 'Intel Corporation'
    device     = '82599ES 10-Gigabit SFI/SFP+ Network Connection'
    class      = network
    subclass   = ethernet
    cap 01[40] = powerspec 3  supports D0 D3  current D0
    cap 05[50] = MSI supports 1 message, 64 bit, vector masks
    cap 11[70] = MSI-X supports 64 messages, enabled
                 Table in map 0x20[0x0], PBA in map 0x20[0x2000]
    cap 10[a0] = PCI-Express 2 endpoint max data 256(512) FLR RO NS
                 max read 512
                 link x4(x8) speed 5.0(5.0) ASPM disabled(L0s)
    cap 03[e0] = VPD
    ecap 0001[100] = AER 1 0 fatal 0 non-fatal 1 corrected
    ecap 0003[140] = Serial 1 a8b8e0ffff05ef51
    ecap 000e[150] = ARI 1
    ecap 0010[160] = SR-IOV 1 IOV disabled, Memory Space disabled, ARI disabled
                     0 VFs configured out of 64 supported
                     First VF RID Offset 0x0180, VF RID Stride 0x0002
                     VF Device ID 0x10ed
                     Page Sizes: 4096 (enabled), 8192, 65536, 262144, 1048576, 4194304
                                    georgelzaG 1 Reply Last reply Reply Quote 0
                                    • georgelzaG
                                      georgelza @georgelza
                                      last edited by georgelza

                                      sweeeeeet... so ye that delivery was 1 x DAC, 1 x other brand SFP+ Transciever.

                                      plugged the DAC in between switch and pfsense SFP+ port 0
                                      plugged the new Transceiver into pmox SFP+ port0
                                      both started flashing...
                                      go onto unifi network controller, both SFP+ ports immediately changed colour to hey we got something we recognise, vs grey or red.

                                      in pmox console,

                                      dmesg =>

                                      [78378.314597] ixgbe 0000:04:00.0 enp4s0f0: detected SFP+: 5
[78433.681346] ixgbe 0000:04:00.0 enp4s0f0: NIC Link is Up 10 Gbps, Flow Control: RX/TX

                                      and ip a

                                      ip a
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default qlen 1000
    link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
    inet 127.0.0.1/8 scope host lo
       valid_lft forever preferred_lft forever
    inet6 ::1/128 scope host noprefixroute
       valid_lft forever preferred_lft forever
2: enp2s0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq master vmbr0 state UP group default qlen 1000
    link/ether a8:b8:e0:02:a3:71 brd ff:ff:ff:ff:ff:ff
3: enp3s0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN group default qlen 1000
    link/ether a8:b8:e0:02:a3:72 brd ff:ff:ff:ff:ff:ff
4: enp5s0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN group default qlen 1000
    link/ether a8:b8:e0:02:a3:73 brd ff:ff:ff:ff:ff:ff
5: enp6s0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN group default qlen 1000
    link/ether a8:b8:e0:02:a3:74 brd ff:ff:ff:ff:ff:ff
8: vmbr0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP group default qlen 1000
    link/ether a8:b8:e0:02:a3:71 brd ff:ff:ff:ff:ff:ff
    inet 172.16.10.50/24 scope global vmbr0
       valid_lft forever preferred_lft forever
    inet6 fe80::aab8:e0ff:fe02:a371/64 scope link
       valid_lft forever preferred_lft forever
9: vmbr40: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP group default qlen 1000
    link/ether a8:b8:e0:05:f0:91 brd ff:ff:ff:ff:ff:ff
    inet6 fe80::aab8:e0ff:fe05:f091/64 scope link
       valid_lft forever preferred_lft forever
10: tap100i0: <BROADCAST,MULTICAST,PROMISC,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast master fwbr100i0 state UNKNOWN group default qlen 1000
    link/ether c6:2d:5a:7a:41:d7 brd ff:ff:ff:ff:ff:ff
11: fwbr100i0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP group default qlen 1000
    link/ether da:0c:52:e1:39:89 brd ff:ff:ff:ff:ff:ff
12: fwpr100p0@fwln100i0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue master vmbr0 state UP group default qlen 1000
    link/ether 76:c4:56:d3:6a:93 brd ff:ff:ff:ff:ff:ff
13: fwln100i0@fwpr100p0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue master fwbr100i0 state UP group default qlen 1000
    link/ether da:0c:52:e1:39:89 brd ff:ff:ff:ff:ff:ff
14: tap100i1: <BROADCAST,MULTICAST,PROMISC,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast master fwbr100i1 state UNKNOWN group default qlen 1000
    link/ether 76:c9:86:22:cc:30 brd ff:ff:ff:ff:ff:ff
15: fwbr100i1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP group default qlen 1000
    link/ether 52:9a:1c:4d:76:a6 brd ff:ff:ff:ff:ff:ff
16: fwpr100p1@fwln100i1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue master vmbr0 state UP group default qlen 1000
    link/ether 26:2d:af:5a:9a:b4 brd ff:ff:ff:ff:ff:ff
17: fwln100i1@fwpr100p1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue master fwbr100i1 state UP group default qlen 1000
    link/ether 52:9a:1c:4d:76:a6 brd ff:ff:ff:ff:ff:ff
18: tap100i2: <BROADCAST,MULTICAST,PROMISC,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast master fwbr100i2 state UNKNOWN group default qlen 1000
    link/ether c2:9f:1f:4e:c6:2e brd ff:ff:ff:ff:ff:ff
19: fwbr100i2: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP group default qlen 1000
    link/ether 7a:a8:67:a9:29:14 brd ff:ff:ff:ff:ff:ff
20: fwpr100p2@fwln100i2: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue master vmbr40 state UP group default qlen 1000
    link/ether 72:43:cc:4b:b3:40 brd ff:ff:ff:ff:ff:ff
21: fwln100i2@fwpr100p2: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue master fwbr100i2 state UP group default qlen 1000
    link/ether 7a:a8:67:a9:29:14 brd ff:ff:ff:ff:ff:ff
39: enp4s0f0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq master vmbr40 state UP group default qlen 1000
    link/ether a8:b8:e0:05:f0:91 brd ff:ff:ff:ff:ff:ff
40: enp4s0f1: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN group default qlen 1000
    link/ether a8:b8:e0:05:f0:92 brd ff:ff:ff:ff:ff:ff

                                      now to reconfigure vlan40 from the igc0.40 onto ix0

                                      ip a
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default qlen 1000
    link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
    inet 127.0.0.1/8 scope host lo
       valid_lft forever preferred_lft forever
    inet6 ::1/128 scope host
       valid_lft forever preferred_lft forever
2: ens18: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc fq_codel state UP group default qlen 1000
    link/ether bc:24:11:c0:e8:1e brd ff:ff:ff:ff:ff:ff
    inet 172.16.10.51/24 metric 100 brd 172.16.10.255 scope global dynamic ens18
       valid_lft 4206sec preferred_lft 4206sec
    inet6 fe80::be24:11ff:fec0:e81e/64 scope link
       valid_lft forever preferred_lft forever
3: ens19: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc fq_codel state UP group default qlen 1000
    link/ether bc:24:11:81:2c:cb brd ff:ff:ff:ff:ff:ff
    inet6 fe80::be24:11ff:fe81:2ccb/64 scope link
       valid_lft forever preferred_lft forever
4: ens20: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc fq_codel state UP group default qlen 1000
    link/ether bc:24:11:1e:20:ac brd ff:ff:ff:ff:ff:ff
    inet6 fe80::be24:11ff:fe1e:20ac/64 scope link
       valid_lft forever preferred_lft forever
5: docker0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc noqueue state DOWN group default
    link/ether 02:42:cb:d9:fb:26 brd ff:ff:ff:ff:ff:ff
    inet 172.17.0.1/16 brd 172.17.255.255 scope global docker0
       valid_lft forever preferred_lft forever

                                      happiness, making progress in right direction...

                                      i configured my pfSense console to be accessible via 2nd address on 172.16.40.1. reconfigured that via primary 172.16.10.1 interface to now be serviced/routed via ix0, then connected to console via new 2nd, working so have a back door ;)

                                      connected via back door and went and reconfigured vlan0, vlan20, vlan30 to now be routed via ix0 also. hit refresh on my browser which access console via 172.16.10.1 and did same for 172.16.40.1, still accessible.
                                      at this point the below picture reflect pfsense config.

                                      f2e38015-af35-4898-add4-8f71fb865586-image.png

                                      16636561-0b1c-480f-8052-4e3ff1d844bb-image.png

                                      95573970-c2a3-4cfa-adf9-a2e905191da9-image.png

                                      Ok, this seemed good. but (once i unplugged the 2.5 igc1 cat6 cable between ProMax port24 and pfSense ) now found i could not access anything else that sat on 172.16.10.0/24 network.

                                      At this point wondering... am i trying to get something to work and whats the value of it... does it make sense...

                                      To fix the above I reconfigured onto this.

                                      bd1c80f0-8694-484a-b8ea-b7a1109788ee-image.png

                                      65e7497c-373b-4f02-8b6c-6ef14cf3e31e-image.png
                                      b9f16f4d-7eb6-4490-8740-34e31c401c71-image.png

                                      Maybe leave vlan0, vlan20, vlan30 and vlan100 on igc1 as all the device that connect to that themself are either wifi, 1GbE or 2.5GbE based.
                                      then leave vlan40 on ix0 and the device that will on there is 10GbE based.
                                      I got an aggregation on the way anyhow. so SFP+ port 2 on pfSense will go into aggregation and the pmox and TrueNAS will go into that.

                                      some comments, view's

                                      note, on ubuntu-01 i still dont have a ip assigned to the vlan30 and vlan40 interfaces... so thats i guess the last to be fixed...

                                      G

                                      stephenw10S 1 Reply Last reply Reply Quote 0
                                      • georgelzaG
                                        georgelza
                                        last edited by georgelza

                                        for reference, here is my pmox datacenter

                                        41f81967-e175-4d58-8f92-59626d7e033a-image.png

                                        and pmox1 server network configuration.

                                        94b5e93f-97a8-43c7-9bd6-b02db7354487-image.png

                                        interesting enough, without telling my unifi environment, this is what it's showing.

                                        529e43bc-3835-4ee8-a037-e96564d01c5a-image.png

                                        <note the MAC addresses assigned to net1 and net2 has been dhcp reserved in pfsense on the respective vlans as 172.16.30.11 and 172.16.40.11

                                        <interesting take away, the unifi has no problem with the Dell/EMC SFP+ (dell emc ftlx8574d3bnl-fc) Transcievers, it's on the Topton side where they are not liked, I have found a thread on lawrenceIT that points to the following transceivers working also>

                                        10Gtek 10GBase-SR SFP+ LC Transceiver, 10G 850nm Multimode SFP Moduledell emc ftlx8574d3bnl-fc

                                        1 Reply Last reply Reply Quote 0
                                        • stephenw10S
                                          stephenw10 Netgate Administrator @georgelza
                                          last edited by

                                          @georgelza said in pfSense not enabling port:

                                          Ok, this seemed good. but (once i unplugged the 2.5 igc1 cat6 cable between ProMax port24 and pfSense ) now found i could not access anything else that sat on 172.16.10.0/24 network.

                                          Unclear exactly what you are testing to and from in that scenario. Just disconnecting the cable won't start routing via some other subnet if it still has an IP address directly in the subnet.

                                          georgelzaG 1 Reply Last reply Reply Quote 0
                                          • georgelzaG
                                            georgelza @stephenw10
                                            last edited by

                                            @stephenw10

                                            I wanted all traffic between the ProMax & pfSense to flow over the DAC.

                                            why i reconfigured all vlan GW's to then sit on the Ix0 interface.

                                            in the end what i got is vlan0, vlan20, vlan30 and vlan100 which is "low" bandwidth traffic get to the fSense via igb1 / 2.5GbE and then all traffic from vlan40, will sit on ix0,

                                            G

                                            1 Reply Last reply Reply Quote 0
                                            • First post
                                              Last post
                                            Copyright 2025 Rubicon Communications LLC (Netgate). All rights reserved.