1.2.3 upgrade to 2.0 Now USB doesn't work



  • Hi All

    I managed to install and configure pfSence 1.2.3 (i'm a newbie really) with dual wan fail over and load balance and I'm thoroughly impressed with the pfSense team creation. Realising the possibilities I upgraded to:

    FreeBSD pfsense.local 8.1-RELEASE-p2 FreeBSD 8.1-RELEASE-p2 #1: Tue Dec  7 05:16:35 EST 2010
    sullrich@FreeBSD_8.0_pfSense_2.0-snaps.pfsense.org:/usr/obj.pfSense/usr/pfSensesrc/src/sys/pfSense_SMP.8  i386
    

    as I wanted support for a huawei usb modem and also open-vm-tools. The upgrade went smooth. but now USB is not working, could anyone help with a solution? Would I be correct in saying the usb controller is being detected as manufacturer ATI when it is infact Intel?

    Below is dmesg output, loader.conf and pciconf.

    Thanks in advance
    Best regards

    dmesg

    Copyright (c) 1992-2010 The FreeBSD Project.
    Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
    	The Regents of the University of California. All rights reserved.
    FreeBSD is a registered trademark of The FreeBSD Foundation.
    FreeBSD 8.1-RELEASE-p2 #1: Tue Dec  7 05:16:35 EST 2010
        sullrich@FreeBSD_8.0_pfSense_2.0-snaps.pfsense.org:/usr/obj.pfSense/usr/pfSensesrc/src/sys/pfSense_SMP.8 i386
    Timecounter "i8254" frequency 1193182 Hz quality 0
    CPU: Intel(R) Pentium(R) 4 CPU 3.20GHz (3200.14-MHz 686-class CPU)
      Origin = "GenuineIntel"  Id = 0xf41  Family = f  Model = 4  Stepping = 1
      Features=0xbfebfbff <fpu,vme,de,pse,tsc,msr,pae,mce,cx8,apic,sep,mtrr,pge,mca,cmov,pat,pse36,clflush,dts,acpi,mmx,fxsr,sse,sse2,ss,htt,tm,pbe>Features2=0x441d <sse3,dtes64,mon,ds_cpl,cnxt-id,xtpr>AMD Features=0x100000 <nx>TSC: P-state invariant
    real memory  = 1073741824 (1024 MB)
    avail memory = 898641920 (857 MB)
    ACPI APIC Table: <intel  d11020m="">FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs
    FreeBSD/SMP: 1 package(s) x 1 core(s) x 2 HTT threads
     cpu0 (BSP): APIC ID:  0
     cpu1 (AP/HT): APIC ID:  1
    ioapic0: Changing APIC ID to 4
    ioapic0 <version 2.1="">irqs 0-23 on motherboard
    wlan: mac acl policy registered
    kbd1 at kbdmux0
    cryptosoft0: <software crypto="">on motherboard
    padlock0: No ACE support.
    acpi0: <intel d11020m="">on motherboard
    acpi0: Overriding SCI Interrupt from IRQ 9 to IRQ 21
    acpi0: [ITHREAD]
    acpi0: Power Button (fixed)
    unknown: I/O range not supported
    acpi0: reservation of 0, a0000 (3) failed
    acpi0: reservation of 100000, 37f00000 (3) failed
    Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
    acpi_timer0: <32-bit timer at 3.579545MHz> port 0x408-0x40b on acpi0
    cpu0: <acpi cpu="">on acpi0
    cpu1: <acpi cpu="">on acpi0
    acpi_button0: <power button="">on acpi0
    pcib0: <acpi host-pci="" bridge="">port 0xcf8-0xcff iomem 0xfff00000-0xffffffff on acpi0
    pci0: <acpi pci="" bus="">on pcib0
    pcib1: <acpi pci-pci="" bridge="">at device 1.0 on pci0
    pci1: <acpi pci="" bus="">on pcib1
    vgapci0: <vga-compatible display="">port 0x2000-0x20ff mem 0x40000000-0x4fffffff,0x60100000-0x6010ffff irq 17 at device 5.0 on pci1
    atapci0: <ati ixp400="" sata150="" controller="">port 0x3068-0x306f,0x3084-0x3087,0x3060-0x3067,0x3080-0x3083,0x3030-0x303f mem 0x60207600-0x602077ff irq 23 at device 17.0 on pci0
    atapci0: [ITHREAD]
    ata2: <ata 0="" channel="">on atapci0
    ata2: [ITHREAD]
    ata3: <ata 1="" channel="">on atapci0
    ata3: [ITHREAD]
    atapci1: <ati ixp400="" sata150="" controller="">port 0x3058-0x305f,0x307c-0x307f,0x3050-0x3057,0x3078-0x307b,0x3020-0x302f mem 0x60207400-0x602075ff irq 22 at device 18.0 on pci0
    atapci1: [ITHREAD]
    ata4: <ata 0="" channel="">on atapci1
    ata4: [ITHREAD]
    ata5: <ata 1="" channel="">on atapci1
    ata5: [ITHREAD]
    ohci0: <ati sb400="" usb="" controller="">mem 0x80000000-0x80000fff irq 19 at device 19.0 on pci0
    ohci0: [ITHREAD]
    usbus0: <ati sb400="" usb="" controller="">on ohci0
    ohci1: <ati sb400="" usb="" controller="">mem 0x80000000-0x80000fff irq 19 at device 19.1 on pci0
    ohci1: Could not map memory
    device_attach: ohci1 attach returned 6
    ehci0: <ati sb400="" usb="" 2.0="" controller="">mem 0x80000000-0x80000fff irq 19 at device 19.2 on pci0
    ehci0: Could not map memory
    device_attach: ehci0 attach returned 6
    pci0: <serial bus,="" smbus="">at device 20.0 (no driver attached)
    atapci2: <ati ixp400="" udma133="" controller="">port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0x3000-0x300f at device 20.1 on pci0
    ata0: <ata 0="" channel="">on atapci2
    ata0: [ITHREAD]
    ata1: <ata 1="" channel="">on atapci2
    ata1: [ITHREAD]
    pci0: <multimedia, hda="">at device 20.2 (no driver attached)
    isab0: <pci-isa bridge="">at device 20.3 on pci0
    isa0: <isa bus="">on isab0
    pcib2: <acpi pci-pci="" bridge="">at device 20.4 on pci0
    pci2: <acpi pci="" bus="">on pcib2
    rl0: <realtek 10="" 8139="" 100basetx="">port 0x1200-0x12ff mem 0x60001100-0x600011ff irq 21 at device 2.0 on pci2
    miibus0: <mii bus="">on rl0
    rlphy0: <realtek internal="" media="" interface="">PHY 0 on miibus0
    rlphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
    rl0: [ITHREAD]
    rl1: <accton 10="" 5030="" 5038="" mpx="" 100basetx="">port 0x1100-0x11ff mem 0x60001000-0x600010ff irq 16 at device 3.0 on pci2
    miibus1: <mii bus="">on rl1
    rlphy1: <realtek internal="" media="" interface="">PHY 0 on miibus1
    rlphy1:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
    rl1: [ITHREAD]
    sis0: <sis 10="" 900="" 100basetx="">port 0x1000-0x10ff mem 0x60000000-0x60000fff irq 17 at device 4.0 on pci2
    miibus2: <mii bus="">on sis0
    ukphy0: <generic ieee="" 802.3u="" media="" interface="">PHY 0 on miibus2
    ukphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
    sis0: [ITHREAD]
    atrtc0: <at realtime="" clock="">port 0x70-0x71 on acpi0
    atkbdc0: <keyboard controller="" (i8042)="">port 0x60,0x64 irq 1 on acpi0
    atkbd0: <at keyboard="">irq 1 on atkbdc0
    kbd0 at atkbd0
    atkbd0: [GIANT-LOCKED]
    atkbd0: [ITHREAD]
    psm0: <ps 2="" mouse="">irq 12 on atkbdc0
    psm0: [GIANT-LOCKED]
    psm0: [ITHREAD]
    psm0: model IntelliMouse, device ID 3
    ppc0: <parallel port="">port 0x378-0x37f irq 7 on acpi0
    ppc0: Generic chipset (EPP/NIBBLE) in COMPATIBLE mode
    ppc0: [ITHREAD]
    ppbus0: <parallel port="" bus="">on ppc0
    plip0: <plip network="" interface="">on ppbus0
    plip0: [ITHREAD]
    lpt0: <printer>on ppbus0
    lpt0: [ITHREAD]
    lpt0: Interrupt-driven port
    ppi0: <parallel i="" o="">on ppbus0
    uart0: <16550 or compatible> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0
    uart0: [FILTER]
    pmtimer0 on isa0
    orm0: <isa option="" rom="">at iomem 0xc0000-0xcbfff pnpid ORM0000 on isa0
    sc0: <system console="">at flags 0x100 on isa0
    sc0: VGA <16 virtual consoles, flags=0x300>
    vga0: <generic isa="" vga="">at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
    p4tcc0: <cpu frequency="" thermal="" control="">on cpu0
    p4tcc1: <cpu frequency="" thermal="" control="">on cpu1
    RTC BIOS diagnostic error 80 <clock_battery>Timecounters tick every 1.000 msec
    IPsec: Initialized Security Association Processing.
    usbus0: 12Mbps Full Speed USB v1.0
    ugen0.1: <ati>at usbus0
    uhub0: <ati 1="" 9="" ohci="" root="" hub,="" class="" 0,="" rev="" 1.00="" 1.00,="" addr="">on usbus0
    uhub_attach: getting hub descriptor failed,error=USB_ERR_SHORT_XFER
    device_attach: uhub0 attach returned 6
    uhub0: <ati 1="" 9="" ohci="" root="" hub,="" class="" 0,="" rev="" 1.00="" 1.00,="" addr="">on usbus0
    uhub_attach: getting hub descriptor failed,error=USB_ERR_SHORT_XFER
    device_attach: uhub0 attach returned 6
    usbus0: Root HUB problem, error=USB_ERR_NO_ROOT_HUB
    acd0: CDRW <lite-on combo="" sohc-4832k="" oqkb="">at ata0-master UDMA40 
    ad8: DMA limited to UDMA33, device found non-ATA66 cable
    ad8: 76319MB <seagate st380013as="" 3.43="">at ata4-master UDMA33 
    SMP: AP CPU #1 Launched!
    Trying to mount root from ufs:/dev/ad8s1a
    pflog0: promiscuous mode enabled
    sis0: link state changed to UP
    rl0: link state changed to UP
    rl1: link state changed to UP</seagate></lite-on></ati></ati></ati></clock_battery></cpu></cpu></generic></system></isa></parallel></printer></plip></parallel></parallel></ps></at></keyboard></at></generic></mii></sis></realtek></mii></accton></realtek></mii></realtek></acpi></acpi></isa></pci-isa></multimedia,></ata></ata></ati></serial></ati></ati></ati></ati></ata></ata></ati></ata></ata></ati></vga-compatible></acpi></acpi></acpi></acpi></power></acpi></acpi></intel></software></version></intel></nx></sse3,dtes64,mon,ds_cpl,cnxt-id,xtpr></fpu,vme,de,pse,tsc,msr,pae,mce,cx8,apic,sep,mtrr,pge,mca,cmov,pat,pse36,clflush,dts,acpi,mmx,fxsr,sse,sse2,ss,htt,tm,pbe> 
    

    loader.conf

    kern.cam.boot_delay=10000
    legal.intel_ipw.license_ack=1
    legal.intel_wpi.license_ack=1
    

    pciconf -lv

    hostb0@pci0:0:0:0:	class=0x060000 card=0xd6018086 chip=0x5a331002 rev=0x01 hdr=0x00
        class      = bridge
        subclass   = HOST-PCI
    pcib1@pci0:0:1:0:	class=0x060400 card=0x5a3f1002 chip=0x5a3f1002 rev=0x00 hdr=0x01
        class      = bridge
        subclass   = PCI-PCI
    atapci0@pci0:0:17:0:	class=0x01018f card=0xd6018086 chip=0x437a1002 rev=0x80 hdr=0x00
        class      = mass storage
        subclass   = ATA
    atapci1@pci0:0:18:0:	class=0x01018f card=0xd6018086 chip=0x43791002 rev=0x80 hdr=0x00
        class      = mass storage
        subclass   = ATA
    ohci0@pci0:0:19:0:	class=0x0c0310 card=0xd6018086 chip=0x43741002 rev=0x80 hdr=0x00
        class      = serial bus
        subclass   = USB
    ohci1@pci0:0:19:1:	class=0x0c0310 card=0xd6018086 chip=0x43751002 rev=0x80 hdr=0x00
        class      = serial bus
        subclass   = USB
    ehci0@pci0:0:19:2:	class=0x0c0320 card=0xd6018086 chip=0x43731002 rev=0x80 hdr=0x00
        class      = serial bus
        subclass   = USB
    none0@pci0:0:20:0:	class=0x0c0500 card=0xd6018086 chip=0x43721002 rev=0x81 hdr=0x00
        class      = serial bus
        subclass   = SMBus
    atapci2@pci0:0:20:1:	class=0x01018a card=0xd6018086 chip=0x43761002 rev=0x80 hdr=0x00
        class      = mass storage
        subclass   = ATA
    none1@pci0:0:20:2:	class=0x040300 card=0xd6018086 chip=0x437b1002 rev=0x01 hdr=0x00
        class      = multimedia
        subclass   = HDA
    isab0@pci0:0:20:3:	class=0x060100 card=0xd6018086 chip=0x43771002 rev=0x80 hdr=0x00
        class      = bridge
        subclass   = PCI-ISA
    pcib2@pci0:0:20:4:	class=0x060401 card=0x00000000 chip=0x43711002 rev=0x80 hdr=0x01
        class      = bridge
        subclass   = PCI-PCI
    vgapci0@pci0:1:5:0:	class=0x030000 card=0xd6018086 chip=0x5a611002 rev=0x00 hdr=0x00
        class      = display
        subclass   = VGA
    rl0@pci0:2:2:0:	class=0x020000 card=0xd6018086 chip=0x813910ec rev=0x10 hdr=0x00
        class      = network
        subclass   = ethernet
    rl1@pci0:2:3:0:	class=0x020000 card=0x12111113 chip=0x12111113 rev=0x10 hdr=0x00
        class      = network
        subclass   = ethernet
    sis0@pci0:2:4:0:	class=0x020000 card=0x09001039 chip=0x09001039 rev=0x02 hdr=0x00
        class      = network
        subclass   = ethernet
    
    


  • @PDA:

    but now USB is not working, could anyone help with a solution? Would I be correct in saying the usb controller is being detected as manufacturer ATI when it is infact Intel?

    I can't help with a solution but I can help with a diagnosis. The real problem is shown in the dmesg snippet:

    
    ohci0: <ati sb400="" usb="" controller="">mem 0x80000000-0x80000fff irq 19 at device 19.0 on pci0
    ohci0: [ITHREAD]
    usbus0: <ati sb400="" usb="" controller="">on ohci0
    ohci1: <ati sb400="" usb="" controller="">mem 0x80000000-0x80000fff irq 19 at device 19.1 on pci0
    ohci1: Could not map memory
    device_attach: ohci1 attach returned 6
    ehci0: <ati sb400="" usb="" 2.0="" controller="">mem 0x80000000-0x80000fff irq 19 at device 19.2 on pci0
    ehci0: Could not map memory
    device_attach: ehci0 attach returned 6</ati></ati></ati></ati> 
    

    The BIOS has apparently initialised all three USB controllers so that their device registers are at exactly the same memory address. This is a error.

    As for the Intel/AMD thing: the pciconf output shows a number of PCI devices apparently claiming the chips were made by ATI and the subsystem was made by Intel. Though this is possible it seems to me to be rather unlikely. This is some kind of virtualised environment? I suggest a cold restart.



  • Hi Wallabybob thanks for your help.

    I have tried a cold boot with no change. I have confirmed the manufacturer is ATI for the chipset, Could the below thread be the same problem?

    http://www.mail-archive.com/freebsd-acpi@freebsd.org/msg00367.html

    Below is dmesg with verbose boot.

    Copyright (c) 1992-2010 The FreeBSD Project.
    Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
    	The Regents of the University of California. All rights reserved.
    FreeBSD is a registered trademark of The FreeBSD Foundation.
    FreeBSD 8.1-RELEASE-p2 #1: Tue Dec  7 05:16:35 EST 2010
        sullrich@FreeBSD_8.0_pfSense_2.0-snaps.pfsense.org:/usr/obj.pfSense/usr/pfSensesrc/src/sys/pfSense_SMP.8 i386
    Preloaded elf kernel "/boot/kernel/kernel" at 0xc1367000.
    Timecounter "i8254" frequency 1193182 Hz quality 0
    Calibrating TSC clock ... TSC clock: 3200132328 Hz
    CPU: Intel(R) Pentium(R) 4 CPU 3.20GHz (3200.13-MHz 686-class CPU)
      Origin = "GenuineIntel"  Id = 0xf41  Family = f  Model = 4  Stepping = 1
      Features=0xbfebfbff <fpu,vme,de,pse,tsc,msr,pae,mce,cx8,apic,sep,mtrr,pge,mca,cmov,pat,pse36,clflush,dts,acpi,mmx,fxsr,sse,sse2,ss,htt,tm,pbe>Features2=0x441d <sse3,dtes64,mon,ds_cpl,cnxt-id,xtpr>AMD Features=0x100000 <nx>TSC: P-state invariant
    
    Instruction TLB: 4 KB, 2 MB or 4 MB pages, fully associative, 64 entries
    Data TLB: 4 KB or 4 MB pages, fully associative, 64 entries
    1st-level data cache: 16 KB, 8-way set associative, sectored cache, 64 byte line size
    Trace cache: 12K-uops, 8-way set associative
    2nd-level cache: 1 MB, 8-way set associative, sectored cache, 64 byte line size
    L2 cache: 1024 kbytes, 8-way associative, 64 bytes/line
    real memory  = 1073741824 (1024 MB)
    Physical memory chunk(s):
    0x0000000000001000 - 0x000000000009efff, 647168 bytes (158 pages)
    0x0000000000100000 - 0x00000000003fffff, 3145728 bytes (768 pages)
    0x0000000001426000 - 0x0000000036d23fff, 898621440 bytes (219390 pages)
    0x0000000037d1f000 - 0x0000000037da8fff, 565248 bytes (138 pages)
    0x0000000037dad000 - 0x0000000037e3efff, 598016 bytes (146 pages)
    avail memory = 898641920 (857 MB)
    Table 'FACP' at 0x37efd000
    Table 'APIC' at 0x37ef8000
    APIC: Found table at 0x37ef8000
    MP Configuration Table version 1.4 found at 0xc00fe6b0
    APIC: Using the MADT enumerator.
    MADT: Found CPU APIC ID 0 ACPI ID 1: enabled
    SMP: Added CPU 0 (AP)
    MADT: Found CPU APIC ID 1 ACPI ID 2: enabled
    SMP: Added CPU 1 (AP)
    MADT: Found CPU APIC ID 1 ACPI ID 3: disabled
    MADT: Found CPU APIC ID 3 ACPI ID 4: disabled
    ACPI APIC Table: <intel  d11020m="">FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs
    FreeBSD/SMP: 1 package(s) x 1 core(s) x 2 HTT threads
     cpu0 (BSP): APIC ID:  0
     cpu1 (AP/HT): APIC ID:  1
    x86bios:   IVT 0x000000-0x0004ff at 0xc0000000
    x86bios:  SSEG 0x010000-0x01ffff at 0xc4174000
    x86bios:  EBDA 0x09f000-0x09ffff at 0xc009f000
    x86bios:   ROM 0x0a0000-0x0effff at 0xc00a0000
    APIC: CPU 0 has ACPI ID 1
    APIC: CPU 1 has ACPI ID 2
    pnpbios: Found PnP BIOS data at 0xc00fe0e0
    pnpbios: Entry = f0000:a6db  Rev = 1.0
    pnpbios: OEM ID 8224744e
    Other BIOS signatures found:
    ULE: setup cpu 0
    ULE: setup cpu 1
    ACPI: RSDP 0xfe020 00014 (v0 INTEL )
    ACPI: RSDT 0x37efe038 00030 (v1 INTEL  D11020M  00000429      01000013)
    ACPI: FACP 0x37efd000 00074 (v1 INTEL  D11020M  00000429 MSFT 01000013)
    ACPI: DSDT 0x37ef9000 03474 (v1 INTEL  D11020M  00000429 MSFT 01000013)
    ACPI: FACS 0x37eac000 00040
    ACPI: APIC 0x37ef8000 00084 (v1 INTEL  D11020M  00000429 MSFT 01000013)
    ACPI: MCFG 0x37ef7000 0003C (v1 INTEL  D11020M  00000429 MSFT 01000013)
    MADT: Found IO APIC ID 4, Interrupt 0 at 0xfec00000
    ioapic0: Changing APIC ID to 4
    ioapic0: Routing external 8259A's -> intpin 0
    MADT: Interrupt override: source 0, irq 2
    ioapic0: Routing IRQ 0 -> intpin 2
    MADT: Interrupt override: source 9, irq 21
    ioapic0: intpin 9 disabled
    lapic0: Routing NMI -> LINT1
    lapic0: LINT1 trigger: edge
    lapic0: LINT1 polarity: high
    lapic1: Routing NMI -> LINT1
    lapic1: LINT1 trigger: edge
    lapic1: LINT1 polarity: high
    MADT: Ignoring local NMI routed to ACPI CPU 3
    MADT: Ignoring local NMI routed to ACPI CPU 4
    ioapic0 <version 2.1="">irqs 0-23 on motherboard
    cpu0 BSP:
         ID: 0x00000000   VER: 0x00050014 LDR: 0x00000000 DFR: 0xffffffff
      lint0: 0x00010700 lint1: 0x00000400 TPR: 0x00000000 SVR: 0x000001ff
      timer: 0x000100ef therm: 0x00010000 err: 0x000000f0 pmc: 0x00010400
    firmware: 'iwn5150fw' version 0: 337400 bytes loaded at 0xc1094aa4
    firmware: 'iwn6000fw' version 0: 462280 bytes loaded at 0xc10e7114
    firmware: 'ipw_bss' version 130: 209190 bytes loaded at 0xc0f2a0b0
    firmware: 'ipw_ibss' version 130: 201138 bytes loaded at 0xc0f5d250
    wlan: mac acl policy registered
    firmware: 'mw88W8363fw' version 0: 94940 bytes loaded at 0xc115dbc4
    firmware: 'mwlboot' version 0: 2280 bytes loaded at 0xc1174ea0
    firmware: 'mxge_eth_z8e' version 367564: 116477 bytes loaded at 0xc1175980
    wlan: <802.11 Link Layer>
    firmware: 'mxge_ethp_z8e' version 377876: 117102 bytes loaded at 0xc1192100
    firmware: 'mxge_rss_eth_z8e' version 553468: 154580 bytes loaded at 0xc11aeb00
    firmware: 'mxge_rss_ethp_z8e' version 563868: 155786 bytes loaded at 0xc11d4760
    firmware: 'ipw_monitor' version 130: 196458 bytes loaded at 0xc0f8e47c
    firmware: 'iwn1000fw' version 0: 335056 bytes loaded at 0xc0fbea50
    firmware: 'rt2561fw' version 0: 8192 bytes loaded at 0xc11fe0f0
    firmware: 'rt2561sfw' version 0: 8192 bytes loaded at 0xc1200168
    firmware: 'wpifw' version 2144: 149652 bytes loaded at 0xc1247990
    firmware: 'rt2661fw' version 0: 8192 bytes loaded at 0xc12021e0
    firmware: 'rt2860fw' version 0: 8192 bytes loaded at 0xc1204258
    firmware: 'iwn4965fw' version 0: 187972 bytes loaded at 0xc1010798
    firmware: 'iwn5000fw' version 0: 353240 bytes loaded at 0xc103e654
    null: <null device,="" zero="" device="">random: <entropy source,="" software,="" yarrow="">nfslock: pseudo-device
    crypto: <crypto core="">kbd: new array size 4
    kbd1 at kbdmux0
    mem: <memory>Pentium Pro MTRR support enabled
    io: _hptrr: RocketRAID 17xx/2xxx SATA controller driver v1.2
    npx0: INT 16 interface
    cryptosoft0: <software crypto="">on motherboard
    crypto: assign cryptosoft0 driver id 0, flags 100663296
    crypto: cryptosoft0 registers alg 1 flags 0 maxoplen 0
    crypto: cryptosoft0 registers alg 2 flags 0 maxoplen 0
    crypto: cryptosoft0 registers alg 3 flags 0 maxoplen 0
    crypto: cryptosoft0 registers alg 4 flags 0 maxoplen 0
    crypto: cryptosoft0 registers alg 5 flags 0 maxoplen 0
    crypto: cryptosoft0 registers alg 16 flags 0 maxoplen 0
    crypto: cryptosoft0 registers alg 6 flags 0 maxoplen 0
    crypto: cryptosoft0 registers alg 7 flags 0 maxoplen 0
    crypto: cryptosoft0 registers alg 18 flags 0 maxoplen 0
    crypto: cryptosoft0 registers alg 19 flags 0 maxoplen 0
    crypto: cryptosoft0 registers alg 20 flags 0 maxoplen 0
    crypto: cryptosoft0 registers alg 8 flags 0 maxoplen 0
    crypto: cryptosoft0 registers alg 15 flags 0 maxoplen 0
    crypto: cryptosoft0 registers alg 9 flags 0 maxoplen 0
    crypto: cryptosoft0 registers alg 10 flags 0 maxoplen 0
    crypto: cryptosoft0 registers alg 13 flags 0 maxoplen 0
    crypto: cryptosoft0 registers alg 14 flags 0 maxoplen 0
    crypto: cryptosoft0 registers alg 11 flags 0 maxoplen 0
    crypto: cryptosoft0 registers alg 21 flags 0 maxoplen 0
    crypto: cryptosoft0 registers alg 17 flags 0 maxoplen 0
    padlock0: No ACE support.
    acpi0: <intel d11020m="">on motherboard
    PCIe: Memory Mapped configuration base @ 0xe0000000
    pcibios: No call entry point
    acpi0: Overriding SCI Interrupt from IRQ 9 to IRQ 21
    ioapic0: routing intpin 21 (PCI IRQ 21) to lapic 0 vector 48
    acpi0: [MPSAFE]
    acpi0: [ITHREAD]
    acpi0: Power Button (fixed)
    acpi0: wakeup code va 0xc416e000 pa 0x1000
    acpi_bus_number: root bus has no _BBN, assuming 0
    AcpiOsDerivePciId: \\_SB_.PCI0.MREG -> bus 0 dev 0 func 0
    acpi_bus_number: root bus has no _BBN, assuming 0
    AcpiOsDerivePciId: \\_SB_.PCI0.SMBS.IRQF -> bus 0 dev 20 func 0
    unknown: I/O range not supported
    acpi0: reservation of 0, a0000 (3) failed
    acpi0: reservation of 100000, 37f00000 (3) failed
    ACPI timer: 1/1 1/1 1/1 1/1 1/1 1/1 1/1 1/1 1/1 1/1 -> 10
    Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
    acpi_timer0: <32-bit timer at 3.579545MHz> port 0x408-0x40b on acpi0
    cpu0: <acpi cpu="">on acpi0
    cpu0: switching to generic Cx mode
    cpu1: <acpi cpu="">on acpi0
    pci_link0:        Index  IRQ  Rtd  Ref  IRQs
      Initial Probe       0  255   N     0  3 4 5 7 10 11 12 14 15
      Validation          0  255   N     0  3 4 5 7 10 11 12 14 15
      After Disable       0  255   N     0  3 4 5 7 10 11 12 14 15
    pci_link1:        Index  IRQ  Rtd  Ref  IRQs
      Initial Probe       0  255   N     0  3 4 5 7 10 11 12 14 15
      Validation          0  255   N     0  3 4 5 7 10 11 12 14 15
      After Disable       0  255   N     0  3 4 5 7 10 11 12 14 15
    pci_link2:        Index  IRQ  Rtd  Ref  IRQs
      Initial Probe       0  255   N     0  3 4 5 7 10 11 12 14 15
      Validation          0  255   N     0  3 4 5 7 10 11 12 14 15
      After Disable       0  255   N     0  3 4 5 7 10 11 12 14 15
    pci_link3:        Index  IRQ  Rtd  Ref  IRQs
      Initial Probe       0  255   N     0  3 4 5 7 10 11 12 14 15
      Validation          0  255   N     0  3 4 5 7 10 11 12 14 15
      After Disable       0  255   N     0  3 4 5 7 10 11 12 14 15
    pci_link4:        Index  IRQ  Rtd  Ref  IRQs
      Initial Probe       0  255   N     0  3 4 5 7 10 11 12 14 15
      Validation          0  255   N     0  3 4 5 7 10 11 12 14 15
      After Disable       0  255   N     0  3 4 5 7 10 11 12 14 15
    pci_link5:        Index  IRQ  Rtd  Ref  IRQs
      Initial Probe       0  255   N     0  3 4 5 7 10 11 12 14 15
      Validation          0  255   N     0  3 4 5 7 10 11 12 14 15
      After Disable       0  255   N     0  3 4 5 7 10 11 12 14 15
    pci_link6:        Index  IRQ  Rtd  Ref  IRQs
      Initial Probe       0  255   N     0  3 4 5 7 10 11 12 14 15
      Validation          0  255   N     0  3 4 5 7 10 11 12 14 15
      After Disable       0  255   N     0  3 4 5 7 10 11 12 14 15
    pci_link7:        Index  IRQ  Rtd  Ref  IRQs
      Initial Probe       0  255   N     0  3 4 5 7 10 11 12 14 15
      Validation          0  255   N     0  3 4 5 7 10 11 12 14 15
      After Disable       0  255   N     0  3 4 5 7 10 11 12 14 15
    acpi_button0: <power button="">on acpi0
    pcib0: <acpi host-pci="" bridge="">port 0xcf8-0xcff iomem 0xfff00000-0xffffffff on acpi0
    pci0: <acpi pci="" bus="">on pcib0
    pci0: domain=0, physical bus=0
    found->	vendor=0x1002, dev=0x5a33, revid=0x01
    	domain=0, bus=0, slot=0, func=0
    	class=06-00-00, hdrtype=0x00, mfdev=0
    	cmdreg=0x0006, statreg=0x2220, cachelnsz=0 (dwords)
    	lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
    found->	vendor=0x1002, dev=0x5a3f, revid=0x00
    	domain=0, bus=0, slot=1, func=0
    	class=06-04-00, hdrtype=0x01, mfdev=0
    	cmdreg=0x0007, statreg=0x0230, cachelnsz=0 (dwords)
    	lattimer=0x40 (1920 ns), mingnt=0x08 (2000 ns), maxlat=0x00 (0 ns)
    found->	vendor=0x1002, dev=0x437a, revid=0x80
    	domain=0, bus=0, slot=17, func=0
    	class=01-01-8f, hdrtype=0x00, mfdev=0
    	cmdreg=0x0007, statreg=0x02b0, cachelnsz=16 (dwords)
    	lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
    	intpin=a, irq=10
    	powerspec 2  supports D0 D1 D2 D3  current D0
    	MSI supports 1 message
    	map[10]: type I/O Port, range 32, base 0x3068, size  3, enabled
    	map[14]: type I/O Port, range 32, base 0x3084, size  2, enabled
    	map[18]: type I/O Port, range 32, base 0x3060, size  3, enabled
    	map[1c]: type I/O Port, range 32, base 0x3080, size  2, enabled
    	map[20]: type I/O Port, range 32, base 0x3030, size  4, enabled
    	map[24]: type Memory, range 32, base 0x60207600, size  9, enabled
    pcib0: matched entry for 0.17.INTA
    pcib0: slot 17 INTA hardwired to IRQ 23
    found->	vendor=0x1002, dev=0x4379, revid=0x80
    	domain=0, bus=0, slot=18, func=0
    	class=01-01-8f, hdrtype=0x00, mfdev=0
    	cmdreg=0x0007, statreg=0x02b0, cachelnsz=16 (dwords)
    	lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
    	intpin=a, irq=11
    	powerspec 2  supports D0 D1 D2 D3  current D0
    	MSI supports 1 message
    	map[10]: type I/O Port, range 32, base 0x3058, size  3, enabled
    	map[14]: type I/O Port, range 32, base 0x307c, size  2, enabled
    	map[18]: type I/O Port, range 32, base 0x3050, size  3, enabled
    	map[1c]: type I/O Port, range 32, base 0x3078, size  2, enabled
    	map[20]: type I/O Port, range 32, base 0x3020, size  4, enabled
    	map[24]: type Memory, range 32, base 0x60207400, size  9, enabled
    pcib0: matched entry for 0.18.INTA
    pcib0: slot 18 INTA hardwired to IRQ 22
    found->	vendor=0x1002, dev=0x4374, revid=0x80
    	domain=0, bus=0, slot=19, func=0
    	class=0c-03-10, hdrtype=0x00, mfdev=1
    	cmdreg=0x0000, statreg=0x02b0, cachelnsz=16 (dwords)
    	lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
    	intpin=a, irq=11
    	MSI supports 1 message
    	map[10]: type Memory, range 32, base 0, size 12, memory disabled
    pcib0: matched entry for 0.19.INTA
    pcib0: slot 19 INTA hardwired to IRQ 19
    unknown: Lazy allocation of 0x1000 bytes rid 0x10 type 3 at 0x80000000
    unknown: Reserved 0x1000 bytes for rid 0x10 type 3 at 0x80000000
    found->	vendor=0x1002, dev=0x4375, revid=0x80
    	domain=0, bus=0, slot=19, func=1
    	class=0c-03-10, hdrtype=0x00, mfdev=0
    	cmdreg=0x0000, statreg=0x02a0, cachelnsz=16 (dwords)
    	lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
    	intpin=a, irq=11
    	map[10]: type Memory, range 32, base 0, size 12, memory disabled
    pcib0: matched entry for 0.19.INTA
    pcib0: slot 19 INTA hardwired to IRQ 19
    unknown: Lazy allocation of 0x1000 bytes rid 0x10 type 3 at 0x80000000
    unknown: Reserved 0x1000 bytes for rid 0x10 type 3 at 0x80000000
    found->	vendor=0x1002, dev=0x4373, revid=0x80
    	domain=0, bus=0, slot=19, func=2
    	class=0c-03-20, hdrtype=0x00, mfdev=0
    	cmdreg=0x0000, statreg=0x02b0, cachelnsz=16 (dwords)
    	lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
    	intpin=a, irq=11
    	powerspec 2  supports D0 D1 D2 D3  current D0
    	MSI supports 1 message
    	map[10]: type Memory, range 32, base 0, size 12, memory disabled
    pcib0: matched entry for 0.19.INTA
    pcib0: slot 19 INTA hardwired to IRQ 19
    unknown: Lazy allocation of 0x1000 bytes rid 0x10 type 3 at 0x80000000
    unknown: Reserved 0x1000 bytes for rid 0x10 type 3 at 0x80000000
    ehci early: SMM active, request owner change
    ehci early: SMM does not respond
    found->	vendor=0x1002, dev=0x4372, revid=0x81
    	domain=0, bus=0, slot=20, func=0
    	class=0c-05-00, hdrtype=0x00, mfdev=1
    	cmdreg=0x0003, statreg=0x0220, cachelnsz=0 (dwords)
    	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
    	map[10]: type I/O Port, range 32, base 0x3010, size  4, enabled
    	map[14]: type Memory, range 32, base 0x60207000, size 10, enabled
    found->	vendor=0x1002, dev=0x4376, revid=0x80
    	domain=0, bus=0, slot=20, func=1
    	class=01-01-8a, hdrtype=0x00, mfdev=0
    	cmdreg=0x0015, statreg=0x0230, cachelnsz=0 (dwords)
    	lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
    	intpin=a, irq=255
    	MSI supports 1 message
    	map[20]: type I/O Port, range 32, base 0x3000, size  4, enabled
    found->	vendor=0x1002, dev=0x437b, revid=0x01
    	domain=0, bus=0, slot=20, func=2
    	class=04-03-00, hdrtype=0x00, mfdev=0
    	cmdreg=0x0006, statreg=0x0410, cachelnsz=8 (dwords)
    	lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
    	intpin=a, irq=11
    	powerspec 2  supports D0 D3  current D0
    	MSI supports 1 message, 64 bit
    	map[10]: type Memory, range 64, base 0x60200000, size 14, enabled
    pcib0: matched entry for 0.20.INTA
    pcib0: slot 20 INTA hardwired to IRQ 16
    found->	vendor=0x1002, dev=0x4377, revid=0x80
    	domain=0, bus=0, slot=20, func=3
    	class=06-01-00, hdrtype=0x00, mfdev=1
    	cmdreg=0x000f, statreg=0x0220, cachelnsz=0 (dwords)
    	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
    found->	vendor=0x1002, dev=0x4371, revid=0x80
    	domain=0, bus=0, slot=20, func=4
    	class=06-04-01, hdrtype=0x01, mfdev=1
    	cmdreg=0x0007, statreg=0x02a0, cachelnsz=0 (dwords)
    	lattimer=0x40 (1920 ns), mingnt=0x04 (1000 ns), maxlat=0x00 (0 ns)
    pcib1: <acpi pci-pci="" bridge="">at device 1.0 on pci0
    pcib1:   domain            0
    pcib1:   secondary bus     1
    pcib1:   subordinate bus   1
    pcib1:   I/O decode        0x2000-0x2fff
    pcib1:   memory decode     0x60100000-0x601fffff
    pcib1:   prefetched decode 0x40000000-0x5fffffff
    pci1: <acpi pci="" bus="">on pcib1
    pci1: domain=0, physical bus=1
    found->	vendor=0x1002, dev=0x5a61, revid=0x00
    	domain=0, bus=1, slot=5, func=0
    	class=03-00-00, hdrtype=0x00, mfdev=0
    	cmdreg=0x0007, statreg=0x02b0, cachelnsz=16 (dwords)
    	lattimer=0x40 (1920 ns), mingnt=0x08 (2000 ns), maxlat=0x00 (0 ns)
    	intpin=a, irq=11
    	powerspec 2  supports D0 D1 D2 D3  current D0
    	MSI supports 1 message
    	map[10]: type Prefetchable Memory, range 32, base 0x40000000, size 28, enabled
    pcib1: requested memory range 0x40000000-0x4fffffff: good
    	map[14]: type I/O Port, range 32, base 0x2000, size  8, enabled
    pcib1: requested I/O range 0x2000-0x20ff: in range
    	map[18]: type Memory, range 32, base 0x60100000, size 16, enabled
    pcib1: requested memory range 0x60100000-0x6010ffff: good
    pcib1: matched entry for 1.5.INTA
    pcib1: slot 5 INTA hardwired to IRQ 17
    vgapci0: <vga-compatible display="">port 0x2000-0x20ff mem 0x40000000-0x4fffffff,0x60100000-0x6010ffff irq 17 at device 5.0 on pci1
    atapci0: <ati ixp400="" sata150="" controller="">port 0x3068-0x306f,0x3084-0x3087,0x3060-0x3067,0x3080-0x3083,0x3030-0x303f mem 0x60207600-0x602077ff irq 23 at device 17.0 on pci0
    atapci0: Reserved 0x10 bytes for rid 0x20 type 4 at 0x3030
    ioapic0: routing intpin 23 (PCI IRQ 23) to lapic 0 vector 49
    atapci0: [MPSAFE]
    atapci0: [ITHREAD]
    ata2: <ata 0="" channel="">on atapci0
    atapci0: Reserved 0x8 bytes for rid 0x10 type 4 at 0x3068
    atapci0: Reserved 0x4 bytes for rid 0x14 type 4 at 0x3084
    ata2: reset tp1 mask=02 ostat0=fe ostat1=00
    ata2: stat1=0x00 err=0x00 lsb=0x00 msb=0x00
    ata2: reset tp2 stat0=00 stat1=00 devices=0x0
    ata2: [MPSAFE]
    ata2: [ITHREAD]
    ata3: <ata 1="" channel="">on atapci0
    atapci0: Reserved 0x8 bytes for rid 0x18 type 4 at 0x3060
    atapci0: Reserved 0x4 bytes for rid 0x1c type 4 at 0x3080
    ata3: reset tp1 mask=02 ostat0=fe ostat1=00
    ata3: stat1=0x00 err=0x00 lsb=0x00 msb=0x00
    ata3: reset tp2 stat0=00 stat1=00 devices=0x0
    ata3: [MPSAFE]
    ata3: [ITHREAD]
    atapci1: <ati ixp400="" sata150="" controller="">port 0x3058-0x305f,0x307c-0x307f,0x3050-0x3057,0x3078-0x307b,0x3020-0x302f mem 0x60207400-0x602075ff irq 22 at device 18.0 on pci0
    atapci1: Reserved 0x10 bytes for rid 0x20 type 4 at 0x3020
    ioapic0: routing intpin 22 (PCI IRQ 22) to lapic 0 vector 50
    atapci1: [MPSAFE]
    atapci1: [ITHREAD]
    ata4: <ata 0="" channel="">on atapci1
    atapci1: Reserved 0x8 bytes for rid 0x10 type 4 at 0x3058
    atapci1: Reserved 0x4 bytes for rid 0x14 type 4 at 0x307c
    ata4: reset tp1 mask=03 ostat0=50 ostat1=00
    ata4: stat0=0x50 err=0x01 lsb=0x00 msb=0x00
    ata4: stat1=0x00 err=0x01 lsb=0x00 msb=0x00
    ata4: reset tp2 stat0=50 stat1=00 devices=0x1
    ata4: [MPSAFE]
    ata4: [ITHREAD]
    ata5: <ata 1="" channel="">on atapci1
    atapci1: Reserved 0x8 bytes for rid 0x18 type 4 at 0x3050
    atapci1: Reserved 0x4 bytes for rid 0x1c type 4 at 0x3078
    ata5: reset tp1 mask=02 ostat0=fe ostat1=00
    ata5: stat1=0x00 err=0x00 lsb=0x00 msb=0x00
    ata5: reset tp2 stat0=00 stat1=00 devices=0x0
    ata5: [MPSAFE]
    ata5: [ITHREAD]
    ohci0: <ati sb400="" usb="" controller="">mem 0x80000000-0x80000fff irq 19 at device 19.0 on pci0
    ioapic0: routing intpin 19 (PCI IRQ 19) to lapic 0 vector 51
    ohci0: [MPSAFE]
    ohci0: [ITHREAD]
    usbus0: <ati sb400="" usb="" controller="">on ohci0
    ohci1: <ati sb400="" usb="" controller="">mem 0x80000000-0x80000fff irq 19 at device 19.1 on pci0
    ohci1: Could not map memory
    device_attach: ohci1 attach returned 6
    ehci0: <ati sb400="" usb="" 2.0="" controller="">mem 0x80000000-0x80000fff irq 19 at device 19.2 on pci0
    ehci0: Could not map memory
    device_attach: ehci0 attach returned 6
    pci0: <serial bus,="" smbus="">at device 20.0 (no driver attached)
    atapci2: <ati ixp400="" udma133="" controller="">port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0x3000-0x300f at device 20.1 on pci0
    atapci2: Reserved 0x10 bytes for rid 0x20 type 4 at 0x3000
    ata0: <ata 0="" channel="">on atapci2
    atapci2: Reserved 0x8 bytes for rid 0x10 type 4 at 0x1f0
    atapci2: Reserved 0x1 bytes for rid 0x14 type 4 at 0x3f6
    ata0: reset tp1 mask=03 ostat0=50 ostat1=00
    ata0: stat0=0x00 err=0x01 lsb=0x14 msb=0xeb
    ata0: stat1=0x00 err=0x00 lsb=0x00 msb=0x00
    ata0: reset tp2 stat0=00 stat1=00 devices=0x10000
    ioapic0: routing intpin 14 (ISA IRQ 14) to lapic 0 vector 52
    ata0: [MPSAFE]
    ata0: [ITHREAD]
    ata1: <ata 1="" channel="">on atapci2
    atapci2: Reserved 0x8 bytes for rid 0x18 type 4 at 0x170
    atapci2: Reserved 0x1 bytes for rid 0x1c type 4 at 0x376
    ata1: reset tp1 mask=03 ostat0=7f ostat1=7f
    ata1: stat0=0x7f err=0x7f lsb=0x7f msb=0x7f
    ata1: stat0=0x7f err=0x7f lsb=0x7f msb=0x7f
    ata1: stat0=0x7f err=0x7f lsb=0x7f msb=0x7f
    ata1: stat0=0x7f err=0x7f lsb=0x7f msb=0x7f
    ata1: stat0=0x7f err=0x7f lsb=0x7f msb=0x7f
    ata1: stat0=0x7f err=0x7f lsb=0x7f msb=0x7f
    ata1: stat0=0x7f err=0x7f lsb=0x7f msb=0x7f
    ata1: stat0=0x7f err=0x7f lsb=0x7f msb=0x7f
    ata1: stat0=0x7f err=0x7f lsb=0x7f msb=0x7f
    ata1: stat0=0x7f err=0x7f lsb=0x7f msb=0x7f
    ata1: stat0=0x7f err=0x7f lsb=0x7f msb=0x7f
    ata1: stat0=0x7f err=0x7f lsb=0x7f msb=0x7f
    ata1: stat1=0x7f err=0x7f lsb=0x7f msb=0x7f
    ata1: reset tp2 stat0=ff stat1=ff devices=0x0
    ioapic0: routing intpin 15 (ISA IRQ 15) to lapic 0 vector 53
    ata1: [MPSAFE]
    ata1: [ITHREAD]
    pci0: <multimedia, hda="">at device 20.2 (no driver attached)
    isab0: <pci-isa bridge="">at device 20.3 on pci0
    isa0: <isa bus="">on isab0
    pcib2: <acpi pci-pci="" bridge="">at device 20.4 on pci0
    pcib2:   domain            0
    pcib2:   secondary bus     2
    pcib2:   subordinate bus   2
    pcib2:   I/O decode        0x1000-0x1fff
    pcib2:   memory decode     0x60000000-0x600fffff
    pcib2:   no prefetched decode
    pcib2:   Subtractively decoded bridge.
    pci2: <acpi pci="" bus="">on pcib2
    pci2: domain=0, physical bus=2
    found->	vendor=0x10ec, dev=0x8139, revid=0x10
    	domain=0, bus=2, slot=2, func=0
    	class=02-00-00, hdrtype=0x00, mfdev=0
    	cmdreg=0x0007, statreg=0x0290, cachelnsz=0 (dwords)
    	lattimer=0x40 (1920 ns), mingnt=0x20 (8000 ns), maxlat=0x40 (16000 ns)
    	intpin=a, irq=11
    	powerspec 2  supports D0 D1 D2 D3  current D0
    	map[10]: type I/O Port, range 32, base 0x1200, size  8, enabled
    pcib2: requested I/O range 0x1200-0x12ff: in range
    	map[14]: type Memory, range 32, base 0x60001100, size  8, enabled
    pcib2: requested memory range 0x60001100-0x600011ff: good
    pcib2: matched entry for 2.2.INTA
    pcib2: slot 2 INTA hardwired to IRQ 21
    found->	vendor=0x1113, dev=0x1211, revid=0x10
    	domain=0, bus=2, slot=3, func=0
    	class=02-00-00, hdrtype=0x00, mfdev=0
    	cmdreg=0x0007, statreg=0x0290, cachelnsz=0 (dwords)
    	lattimer=0x40 (1920 ns), mingnt=0x20 (8000 ns), maxlat=0x40 (16000 ns)
    	intpin=a, irq=11
    	powerspec 2  supports D0 D1 D2 D3  current D0
    	map[10]: type I/O Port, range 32, base 0x1100, size  8, enabled
    pcib2: requested I/O range 0x1100-0x11ff: in range
    	map[14]: type Memory, range 32, base 0x60001000, size  8, enabled
    pcib2: requested memory range 0x60001000-0x600010ff: good
    pcib2: matched entry for 2.3.INTA
    pcib2: slot 3 INTA hardwired to IRQ 16
    found->	vendor=0x1039, dev=0x0900, revid=0x02
    	domain=0, bus=2, slot=4, func=0
    	class=02-00-00, hdrtype=0x00, mfdev=0
    	cmdreg=0x0207, statreg=0x0290, cachelnsz=0 (dwords)
    	lattimer=0x40 (1920 ns), mingnt=0x34 (13000 ns), maxlat=0x0b (2750 ns)
    	intpin=a, irq=11
    	powerspec 2  supports D0 D1 D2 D3  current D0
    	map[10]: type I/O Port, range 32, base 0x1000, size  8, enabled
    pcib2: requested I/O range 0x1000-0x10ff: in range
    	map[14]: type Memory, range 32, base 0x60000000, size 12, enabled
    pcib2: requested memory range 0x60000000-0x60000fff: good
    pcib2: matched entry for 2.4.INTA
    pcib2: slot 4 INTA hardwired to IRQ 17
    rl0: <realtek 10="" 8139="" 100basetx="">port 0x1200-0x12ff mem 0x60001100-0x600011ff irq 21 at device 2.0 on pci2
    rl0: Reserved 0x100 bytes for rid 0x10 type 4 at 0x1200
    miibus0: <mii bus="">on rl0
    rlphy0: <realtek internal="" media="" interface="">PHY 0 on miibus0
    rlphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
    rl0: bpf attached
    rl0: [MPSAFE]
    rl0: [ITHREAD]
    rl1: <accton 10="" 5030="" 5038="" mpx="" 100basetx="">port 0x1100-0x11ff mem 0x60001000-0x600010ff irq 16 at device 3.0 on pci2
    rl1: Reserved 0x100 bytes for rid 0x10 type 4 at 0x1100
    miibus1: <mii bus="">on rl1
    rlphy1: <realtek internal="" media="" interface="">PHY 0 on miibus1
    rlphy1:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
    rl1: bpf attached
    ioapic0: routing intpin 16 (PCI IRQ 16) to lapic 0 vector 54
    rl1: [MPSAFE]
    rl1: [ITHREAD]
    sis0: <sis 10="" 900="" 100basetx="">port 0x1000-0x10ff mem 0x60000000-0x60000fff irq 17 at device 4.0 on pci2
    sis0: Reserved 0x100 bytes for rid 0x10 type 4 at 0x1000
    miibus2: <mii bus="">on sis0
    ukphy0: <generic ieee="" 802.3u="" media="" interface="">PHY 0 on miibus2
    ukphy0: OUI 0x000760, model 0x0000, rev. 0
    ukphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
    sis0: bpf attached
    ioapic0: routing intpin 17 (PCI IRQ 17) to lapic 0 vector 55
    sis0: [MPSAFE]
    sis0: [ITHREAD]
    atrtc0: <at realtime="" clock="">port 0x70-0x71 on acpi0
    atrtc0: registered as a time-of-day clock (resolution 1000000us)
    atkbdc0: <keyboard controller="" (i8042)="">port 0x60,0x64 irq 1 on acpi0
    atkbd0: <at keyboard="">irq 1 on atkbdc0
    kbd0 at atkbd0
    kbd0: atkbd0, generic (0), config:0x0, flags:0x3f0000
    ioapic0: routing intpin 1 (ISA IRQ 1) to lapic 0 vector 56
    atkbd0: [GIANT-LOCKED]
    atkbd0: [ITHREAD]
    psm0: unable to allocate IRQ
    psmcpnp0: <ps 2="" mouse="" port="">irq 12 on acpi0
    psm0: current command byte:0067
    psm0: <ps 2="" mouse="">irq 12 on atkbdc0
    ioapic0: routing intpin 12 (ISA IRQ 12) to lapic 0 vector 57
    psm0: [GIANT-LOCKED]
    psm0: [ITHREAD]
    psm0: model IntelliMouse, device ID 3-00, 3 buttons
    psm0: config:00000000, flags:00000008, packet size:4
    psm0: syncmask:08, syncbits:00
    ppc0: using extended I/O port range
    ppc0: SPP EPP
    ppc0: <parallel port="">port 0x378-0x37f irq 7 on acpi0
    ppc0: Generic chipset (EPP/NIBBLE) in COMPATIBLE mode
    ioapic0: routing intpin 7 (ISA IRQ 7) to lapic 0 vector 58
    ppc0: [MPSAFE]
    ppc0: [ITHREAD]
    ppbus0: <parallel port="" bus="">on ppc0
    plip0: <plip network="" interface="">on ppbus0
    plip0: bpf attached
    plip0: [MPSAFE]
    plip0: [ITHREAD]
    lpt0: <printer>on ppbus0
    lpt0: [MPSAFE]
    lpt0: [ITHREAD]
    lpt0: Interrupt-driven port
    ppi0: <parallel i="" o="">on ppbus0
    uart0: <16550 or compatible> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0
    ioapic0: routing intpin 4 (ISA IRQ 4) to lapic 0 vector 59
    uart0: [FILTER]
    uart0: fast interrupt
    ex_isa_identify()
    pnp_identify: Trying Read_Port at 203
    pnp_identify: Trying Read_Port at 243
    pnp_identify: Trying Read_Port at 283
    pnp_identify: Trying Read_Port at 2c3
    pnp_identify: Trying Read_Port at 303
    pnp_identify: Trying Read_Port at 343
    pnp_identify: Trying Read_Port at 383
    pnp_identify: Trying Read_Port at 3c3
    PNP Identify complete
    unknown: status reg test failed ff
    unknown: status reg test failed ff
    unknown: status reg test failed ff
    unknown: status reg test failed ff
    unknown: status reg test failed ff
    unknown: status reg test failed ff
    ahc_isa_probe 0: ioport 0xc00 alloc failed
    isa_probe_children: disabling PnP devices
    pmtimer0 on isa0
    ata: ata0 already exists; skipping it
    ata: ata1 already exists; skipping it
    atkbdc: atkbdc0 already exists; skipping it
    atrtc: atrtc0 already exists; skipping it
    ppc: ppc0 already exists; skipping it
    sc: sc0 already exists; skipping it
    uart: uart0 already exists; skipping it
    isa_probe_children: probing non-PnP devices
    orm0: <isa option="" rom="">at iomem 0xc0000-0xcbfff pnpid ORM0000 on isa0
    sc0: <system console="">at flags 0x100 on isa0
    sc0: VGA <16 virtual consoles, flags=0x300>
    sc0: fb0, kbd1, terminal emulator: scteken (teken terminal)
    vga0: <generic isa="" vga="">at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
    fdc0 failed to probe at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
    uart1: <ns8250>failed to probe at port 0x2f8-0x2ff irq 3 on isa0
    isa_probe_children: probing PnP devices
    p4tcc0: <cpu frequency="" thermal="" control="">on cpu0
    p4tcc1: <cpu frequency="" thermal="" control="">on cpu1
    Device configuration finished.
    procfs registered
    RTC BIOS diagnostic error 80 <clock_battery>lapic: Divisor 2, Frequency 100004138 Hz
    Timecounter "TSC" frequency 3200132328 Hz quality -100
    Timecounters tick every 1.000 msec
    vlan: initialized, using hash tables with chaining
    crypto: <crypto device="">IPsec: Initialized Security Association Processing.
    pflog0: bpf attached
    enc0: bpf attached
    lo0: bpf attached
    pfsync0: bpf attached
    hptrr: no controller detected.
    ata0: Identifying devices: 00010000
    ata0: New devices: 00010000
    usbus0: 12Mbps Full Speed USB v1.0
    ata0-master: pio=PIO4 wdma=WDMA2 udma=UDMA40 cable=80 wire
    acd0: setting UDMA40
    ugen0.1: <ati>at usbus0
    uhub0: <ati 1="" 9="" ohci="" root="" hub,="" class="" 0,="" rev="" 1.00="" 1.00,="" addr="">on usbus0
    uhub_attach: getting hub descriptor failed,error=USB_ERR_SHORT_XFER
    device_attach: uhub0 attach returned 6
    uhub0: <ati 1="" 9="" ohci="" root="" hub,="" class="" 0,="" rev="" 1.00="" 1.00,="" addr="">on usbus0
    uhub_attach: getting hub descriptor failed,error=USB_ERR_SHORT_XFER
    device_attach: uhub0 attach returned 6
    usbus0: Root HUB problem, error=USB_ERR_NO_ROOT_HUB
    acd0: <lite-on combo="" sohc-4832k="" oqkb="">CDRW drive at ata0 as master
    acd0:  2048KB buffer, UDMA40 
    acd0: Reads: CDR, CDRW, CDDA stream, DVDROM, DVDR, packet
    acd0: Writes: CDR, CDRW, test write, burnproof
    acd0: Audio: play, 255 volume levels
    acd0: Mechanism: ejectable tray, unlocked
    acd0: Medium: no/blank disc
    ata1: Identifying devices: 00000000
    ata1: New devices: 00000000
    ata2: Identifying devices: 00000000
    ata2: New devices: 00000000
    ata3: Identifying devices: 00000000
    ata3: New devices: 00000000
    ata4: Identifying devices: 00000001
    ata4: New devices: 00000001
    ata4-master: pio=PIO4 wdma=WDMA2 udma=UDMA100 cable=40 wire
    ad8: DMA limited to UDMA33, device found non-ATA66 cable
    ad8: setting UDMA33
    ad8: 76319MB <seagate st380013as="" 3.43="">at ata4-master UDMA33 
    ad8: 156301488 sectors [155061C/16H/63S] 16 sectors/interrupt 1 depth queue
    GEOM: new disk ad8
    ad8: Silicon Image check3 failed
    ad8: Adaptec check1 failed
    ad8: LSI (v3) check1 failed
    ad8: LSI (v2) check1 failed
    ad8: FreeBSD check1 failed
    ata5: Identifying devices: 00000000
    ata5: New devices: 00000000
    ATA PseudoRAID loaded
    SMP: AP CPU #1 Launched!
    cpu1 AP:
         ID: 0x01000000   VER: 0x00050014 LDR: 0x00000000 DFR: 0xffffffff
      lint0: 0x00010700 lint1: 0x00000400 TPR: 0x00000000 SVR: 0x000001ff
      timer: 0x000200ef therm: 0x00010000 err: 0x000000f0 pmc: 0x00010400
    Trying to mount root from ufs:/dev/ad8s1a
    ct_to_ts([2010-12-08 17:21:47]) = 1291828907.000000000
    start_init: trying /sbin/init
    pflog0: promiscuous mode enabled
    sis0: link state changed to UP
    rl0: link state changed to UP
    rl1: link state changed to UP
    ts_to_ct(1291828920.282646955) = [2010-12-08 17:22:00]</seagate></lite-on></ati></ati></ati></crypto></clock_battery></cpu></cpu></ns8250></generic></system></isa></parallel></printer></plip></parallel></parallel></ps></ps></at></keyboard></at></generic></mii></sis></realtek></mii></accton></realtek></mii></realtek></acpi></acpi></isa></pci-isa></multimedia,></ata></ata></ati></serial></ati></ati></ati></ati></ata></ata></ati></ata></ata></ati></vga-compatible></acpi></acpi></acpi></acpi></power></acpi></acpi></intel></software>_</memory></crypto></entropy></null></version></intel></nx></sse3,dtes64,mon,ds_cpl,cnxt-id,xtpr></fpu,vme,de,pse,tsc,msr,pae,mce,cx8,apic,sep,mtrr,pge,mca,cmov,pat,pse36,clflush,dts,acpi,mmx,fxsr,sse,sse2,ss,htt,tm,pbe> 
    


  • Either your BIOS is broken (it should allocate distinct memory address ranges to each PCI device) OR it is erroneously configured to boot a 'plug and play' operating system (doing its own PCI device resource allocation). pfSense (FreeBSD) assumes the BIOS will do the PCI resource allocation.


Log in to reply