Watchguard XTM 5 Series

Moose0

Keep in mind that the XTM box BIOS defaults to IDE mode on SATA, not AHCI. If you installed pfSense on a machine in AHCI mode then perhaps it chokes on the XTM in IDE mode… I don't know enough about pfSense driver implementation to be able to talk intelligently about this. Hopefully someone else can chip in.

I did notice the system was in AHCI mode when I was installing to the hard drive. I swapped it to IDE and then booted to a DVD of pfsense and then reinstalled to the drive but I'm getting the same results. I'll test creating the installation media in IDE as well.

Scorch95

If you’re wanting to unlock the bios I would remove the CF card and run straight from the ssd and get it working first. Then follow the instructions on page three of this forum. I believe I used putty and fetched it directly and then updated the bios that way.

@stephenw10:

Investigating the XTM8 box caused me to re-investigate the various bios editing tools available and I have now found that newer versions of amibcp are able to correctly edit the SuperIO tables without corrupting the bios in the process. So now we can have the bios correctly configure the SIO chip for gpio use and set the arm/disarm LED to red at boot, which seems like the way it should have been all along.

Flashing the bios is always a risk and I have bricked my own box doing it many times! However it was always due to a corrupt bios file rather than the flashing process itself and it is possible to recover from a bad flash (see earlier posts here). So the modified bios file is here. Flash at your own risk!

Modifications are:
Bios setup menus are unlocked and some aditional menus are unhidden.
LCD now reports 'pfSense V1.8' at boot time.
Speedstep is unlocked and enabled if you have a compatible CPU.
Arm/Disarm LED is now red from boot.

Probably the safest way to get this file, least chance of corruption, is to fetch it straight to the box.
[2.1-BETA1][root@pfsense.localdomain]/tmp(10): fetch https://sites.google.com/site/pfsensefirebox/home/xtm5_83.rom
xtm5_83.rom                                   100% of 1024 kB 1957 kBps
You can then also check its MD5 sum is correct:
[2.1-BETA1][root@pfsense.localdomain]/tmp(11): md5 xtm5_83.rom
MD5 (xtm5_83.rom) = e75bc93ca2db547a3facb8d611f0d441
Then write it with flashrom from there:
[2.1-BETA1][root@pfsense.localdomain]/tmp(13): flashrom -w xtm5_83.rom
flashrom v0.9.5.2-r1515 on FreeBSD 8.3-RELEASE-p8 (i386), built with libpci 3.1.9, GCC 4.2.1 20070719  [FreeBSD], little endian
flashrom is free software, get the source code at http://www.flashrom.org

Calibrating delay loop... OK.
Found chipset "Intel ICH7/ICH7R". Enabling flash write... OK.
Found ST flash chip "M25P80" (1024 kB, SPI) at physical address 0xfff00000.
Flash image seems to be a legacy BIOS. Disabling coreboot-related checks.
Reading old flash chip contents... done.
Erasing and writing flash chip... Erase/write done.
Verifying flash... VERIFIED.
It may be necessary to reset the CMOS with the on board jumper to get access to the bios menus. My box has been unlocked for so long I can't remember if I had to and I have no easy way to test. ::)

Steve

t-rexky

I made some additional BIOS tweaks and I think I am now done. One thing I was still unable to get working is the password protection of the BIOS - no matter what I tried the unit always bypasses the password check when entering BIOS setup. It has been this way ever since I unlocked it. Here is the list of changes:

ACPI_AML version 0x03:
Introduced independent BIOS minor version codes for ACPI_AML revisions
BIOS branch x.x.An for E3400 CPU, where n is the ACPI_AML revision
BIOS branch x.x.Bn for Q9505S CPU, where n is the ACPI_AML revision
Changed 'Sign On Message' to include 'Unlocked v1.9.A3 / E3400 PT'.
Changed 'Sign On Message' to include 'Unlocked v1.9.B3 / Q9505S PT'.

XTM515-BIOS1.3-UNLOCKED1.9:
Modified BIOS Strings from 'Fan confiruration' to 'Fan configuration'
Modified DVMT BIOS String "This setting is only available for WinXp." to "This setting is only for WindowsXP." & introduced line breaks.
Changed Failsafe and Optimal IDE mode to AHCI (00 -> 02)
Changed Failsafe and Optimal 'Remote Access Term Type' to VT100 (00 -> 01)
Changed Failsafe and Optimal 'Always CF Card Boot' to Disable
Changed 'Sign On Message' to include 'Unlocked v1.9 PT'.

XTM515-BIOS1.3-UNLOCKED1.8b:
Corrected all ACPI_AML iasl Warnings based on "Internet wisdom"
Corrected all applicable ACPI_AML iasl Remarks, 17 benign Remarks remain
Introduced all eight P-states in ACPI_AML for E3400 CPU
Corrected P-sate power consumption values based on XTM5 power measurements
Changed 'Sign On Message' to include 'Unlocked v1.8b PT / E3400'.
Changed 'Sign On Message' to include 'Unlocked v1.8b PT / Q9505S'.

XTM515-BIOS1.3-UNLOCKED1.8a:
Implemented P-state dependencies _PSD in ACPI_AML.
Changed 'Sign On Message' to include 'Unlocked v1.8a PT / E3400'.
Changed 'Sign On Message' to include 'Unlocked v1.8a PT / Q9505S'.

XTM515-BIOS1.3-UNLOCKED1.8:
Changed 'Sign On Message' to include 'Unlocked v1.8 PT / E3400'.
Corrected ACPI version help string line breaks in "Enabled RSDP pointers to 64-bit [...]".

XTM515-BIOS1.3-UNLOCKED1.7:
Changed 'Sign On Message' to include 'Unlocked v1.7 PT / E3400'.
Modified LCD boot string from "WG BIOS 1.3" to "Firewall UTM" in module 1B (Single Link Arch BIOS).

XTM515-BIOS1.3-UNLOCKED1.6:
Changed 'Sign On Message' to include 'Unlocked v1.6 E3400 PT'.
Created two ROM branches, one for E3400 CPU and one for Q9505S CPU.

XTM515-BIOS1.3-UNLOCKED1.5:
Changed 'Sign On Message' to include 'Unlocked v1.5 PT'.
Enabled 'PCIPnP' and 'Chipset' menus.
Enabled 'CPU Configuration' submenu in 'Advanced' menu.
Enabled 'ACPI Configuration' submenu in 'Advanced' menu.

XTM515-BIOS1.3-UNLOCKED1.4:
Updated platform 11 CPUID 1067a microcode to version a0b.

XTM515-BIOS1.3-UNLOCKED1.3:
Disabled 'Lan ByPass Control' submenu in 'Advanced' menu.
Modified BIOS Strings from 'Port0 AHCI Speed limit to' to 'Port0 AHCI Speed limit' for Port0 to Port3.

XTM515-BIOS1.3-UNLOCKED1.2:
Changed 'Aways CF Card Boot' to 'Show' in 'Advanced' menu.

XTM515-BIOS1.3-UNLOCKED1.1:
Unlocked the BIOS by changing 'User Access Level' to 03 in 'Security' menu.

And those who are interested can download it from here:

https://www.dropbox.com/s/icnp3jloiw5rnyb/XTM515-BIOS-v1.9.zip?dl=0

As before, I included the factory and the modified ACPI tables in source format (.dsl) and compiled format (.aml).

DISCLAIMER: These work great for me, but please USE AT YOUR OWN RISK.

stephenw10

Did you add the code to set the ARM LED red? Don't think I can live without that now. ;)

Steve

Moose0

@t-rexky:

Keep in mind that the XTM box BIOS defaults to IDE mode on SATA, not AHCI. If you installed pfSense on a machine in AHCI mode then perhaps it chokes on the XTM in IDE mode… I don't know enough about pfSense driver implementation to be able to talk intelligently about this. Hopefully someone else can chip in.

Figured out what my problem was… I was trying to boot on a GPT partition scheme.. I know what I'm doing, I swear!

t-rexky

@stephenw10:

Did you add the code to set the ARM LED red? Don't think I can live without that now. ;)

Steve

Unfortunately no, this is one of the features that I personally did not require. I presume it's fairly trivial to implement?

stephenw10

Yes just add the registers and values to the bootblock SIO table.

| Register | Value | Description |
| 07 | 08 | Logical device to 8, GPIO2 |
| 30 | 01 | Enable GPIO2 as GPIO |
| f0 | cf | Set bits 4 & 5 as output |
| f1 | 20 | Set bit 5 high, Red |

t-rexky

Looks pretty straight forward, thanks for the info! I also looked up the data sheets to confirm I understand what this is changing.

stephenw10

I spent more hours than I care to admit reading that datasheet! ;)
Finding those values when the GPIOs are not enabled by default required a lot of trial and error.

Steve

t-rexky

I can only imagine how many hours you spent on this! Reverse-engineering can be a lot of fun, but with a general purpose chip and so many possibilities this must have been labour of love…

I modified the most recent version of my unlocked BIOS to implement the LED initialization to red and the adventurous can obtain the file from my dropbox:

https://www.dropbox.com/s/o09qcz21apu4dk6/xtm515-bios1.3-unlocked1.9.led.rom.zip?dl=0

This has been tested on one of my units and it works fine. Please note that this version does not implement any SpeedStep definitions - it is effectively the unlocked WatchGuard factory BIOS with all my other tweaks.

Peter.

t-rexky

Back once more with a little bit of the BIOS modifying information that I promised a while ago. Unfortunately I do not have the time to write elaborate instructions, but in any case there is a minimum amount of knowledge required in order to be successful, so just a few pointers should be enough.

Fundamentally, a few software tools and files are required that one can locate on the "net" with a little bit of effort. As always, be cautious about the source and do the required virus checks, etc., especially for items 1 and 2 below:

AmiBCP-3.51.zip
MMTool_322_1B_21Fix.zip
Intel IASL compiler tools for platform of your choice (I compiled it for my Mac) to modify the ACPI module
Any hex editor if you would like to change the string displayed on the LCD
Intel microcode update files for your CPU

The AmiBCP program is used to unlock the BIOS, modify the displayed menus, enable the red LED, change boot version string, change any other BIOS strings, etc.

The MMTool program is used to extract/insert/replace individual modules within the BIOS. For example, you can use it to replace the microcode for the specific platform and cpuid, or you can replace the ACPI_AML module with one that contains the Speedstep configuration specific to your CPU.

For a little bit more information I would refer you to the ~~realm~~ readme file in my unlocked BIOS archive that I posted a little bit ago. I tried to be a little bit more descriptive in it and indicate where the changes are being made. It should be a good starting point.

Peter.

StlCardsFanJR

I've successfully upgraded an XTM 505 and 515 using the following DIMMs.
XTM 505: CRUCIAL CT25664AA800.K16F (2 GB 240-PIN DDR2 DIMM UNBUFFERED)
XTM 515: G.SKILL F2-6400CL5D-4GBPQ (DDR2 2GB PC2-6400 CL5-5-5-15 1.8V-1.9V) @wildio:

Hi everyone! Thanks for all the info in here. With it, I've managed to convert an XTM 515 to a very nice Sophos box. However, I keep getting stuck on upgrading the memory. I've tried everything I see here and nothing is working. Does anyone have a link or part number for the memory I will need? Would be super awesome! Don't think Amazon is going to let me return anything else for another 10 years probably.

XTM-505_DIMMs.jpg_thumb

XTM-515_DIMMs.jpg_thumb

TraderX

Hi All,

First post with plenty of reading ahead so glad to have found this forum and great to see such a strong community.

Very much rookie status so looking for basics of what I'm missing to get going again.

So far Ive done the following:

Upgraded both XTM530's with ram 4gb and c2d e8400 proc's
Burnt 2 4gb cf cards one with pfsense 2.43 serial image and freedos1.2 using win32disk
Using putty and usb/rj45 fdti chip console cable to connect via console port

Using tab I can access locked bios and navigate through menus, however when I let either
box with either card boot with burnt images 530 boxes seem to freeze with no sign
of OS's running, only cursor in top left or centre of screen unresponsive.

AMIBIOS(C)2006 American Megatrends, Inc.
MB-7580 Ver.WD0 04/26/2010
CPU : Intel(R) Core(TM)2 Duo CPU E8400 @ 3.00GHz
Speed : 3.00 GHz

Press DEL to run Setup (F4 on Remote Keyboard)
Press n if you want to boot from the network
Press F11 for BBS POPUP (F3 on Remote Keyboard)
The MCH is operating with DDR2 667
DRAM Timing: Tcl:5/Tras:15/Trp:5/Trcd:5/Twr:5/Trfc:44/Twtr:3/Trrd:3/Trtp:3
Initializing USB Controllers .. Done.
4062MB OK

Have I missed step or could there be something wrong with hardware or images burnt?

Lastly CPU seems to be running unusually hot at 65 degrees celius so could this be related?

thanks

stephenw10

What exact image did you use? At what point does it appear to freeze?

65C does seem very hot. How are you measuring that? Is the heatsink seated correctly? Fans running?

Steve

TraderX

Hi Steve.

Googled after posting and 65deg seems to be mid range for that proc where the second box
with slower proc runs cooler at 38deg.

conflicting results from further testing??

Both boxes "seem" to freeze after the controller cards loads the CF card images
pfSense-CE-memstick-serial-2.4.3-RELEASE-amd64.img

AMIBIOS(C)2006 American Megatrends, Inc.
MB-7580 Ver.WD0 04/26/2010
CPU : Intel(R) Core(TM)2 Duo CPU E8400 @ 3.00GHz
Speed : 3.00 GHz

Press DEL to run Setup (F4 on Remote Keyboard)
Press n if you want to boot from the network
Press F11 for BBS POPUP (F3 on Remote Keyboard)
The MCH is operating with DDR2 667
DRAM Timing: Tcl:5/Tras:15/Trp:5/Trcd:5/Twr:5/Trfc:44/Twtr:3/Trrd:3/Trtp:3
Initializing USB Controllers .. Done.
4062MB OK

Auto-Detecting Pri Master..IDE Hard Disk
Pri Master : SanDisk SDCFH-004G HDX 6.03
Ultra DMA Mode-2
Auto-detecting USB Mass Storage Devices ..
00 USB mass storage devices found and configured.

0078

However the orig watchguard CF card doesnt seems to freeze still running after 7-10mins

Though strangly after in the bios for 3-5mins it freezes

Freeze.jpg_thumb

stephenw10

Hmm, my box with that same CPU rarely gets above 45C. However that's mostly idle and booted into the OS where it's running various CPU halt features to reduce usage. The BIOS setup does not do that.

Also your CPU target temperature is 70C so the fans are probably not spooling up.

I would expect it to boot that image if it's written to the CF card correctly (I recommend using Etcher) but that's an install image meant for installing to something else like an SSD maybe.

You might try booting a Nano image as a test: https://nyifiles.pfsense.org/mirror/downloads/pfSense-CE-2.3.5-RELEASE-2g-amd64-nanobsd.img.gz

Steve

TraderX

I've removed cleaned and repasted the E8400 proc with similar bios temps
but guessing that is secondary at this stage.

the second box runs at 45dec Celsius so will look at first box temps

Swapped out ram, hdd, switched sata ports, replaced drive, removed partitions but cf card with image above still
wont boot BUT can confirm both boxes boot and work from nana image using etcher which
confirmed was burned sucessfully.

Downloaded last image from pfsense NY USA site where first image was pfsense asia

Will try 2.35 serial amd64 installer but doesnt seem likely will work given 2.43 is stable

Running out of idea of than that?

EDIT: sigh 2.35 did start and installed to hdd so back to troubleshooting why 2.43 wont install on my XTM530?

stephenw10

Did you verify the file checksum?

Allow Etcher to extract the file? (write the img.gz file directly).

I have done exactly that on my box here and it worked fine.

You can always just update from 2.3.5.

Steve

TraderX

didnt know etcher could extract the img.gz file but great feature.

In hindsight may have well been a checksum error, as again downloaded 2.43
serial from another pfsense site and it installed last night.

We learn the most "doing" through our own and other peoples experiences so
thanks so much Steve and hope others will benefit from this.

TraderX

Next ;) would like to unlock the bios with added features, from your experience which is the
latest safe image I could upgrade too?

And the cpu fans are definitely spinning up high then slows which I repasted the cpu heatsink, what else could
be causing the high temps. The heatsink sheild are warm to hot so transfer seems effective.