LCDProc 0.5.4-dev
-
@tix:
Well in 24 hours of running, I've had no issues running with only this screen enabled with the "standard" .92 package.
Hi Tix,
yes, everything worked with 1 screen only, because in that case there were no "extra messages" (activate/ignore/etc.) from LCDd that caused a buffer overflow after some hour.With the new version of the package we should not have this problem anymore…
Can you confirm it?
Thanks,
Michele -
I have downloaded the new package and enabled the following screens:
-Uptime
-Load
-States
-Mbuf
-Interface Traffic(WAN)
None of these scroll left/right.I installed the package and rebooted to have a clean start. I noticed that load seemed a little higher than usual on startup and took a little bit longer to "calm down" but I'm not entirely sure it's related to LCDproc.
I will post later today or tomorrow if there is anything to report as I'm hoping we have this corrected. :)
Thanks so much for the effort Michele!!!
-
So far so good.. i'm using the picolcd.so driver, 20x2 display
The following is enabled:
Time
Uptime
System
Disk
Load
States (Not sure if other notice, it doesn't show the correct max, always 10000)
Interfaces (scrolls thru them)
Mbuf
Interface Traffic (WAN)one day I'll swap to a different case so I can have a 20/4
-
Testing now.
One thing I have noticed that I didn't expect is:[2.0.1-RELEASE][root@pfsense.fire.box]/root(2): ps aux|grep lcd root 4965 0.0 0.3 3656 1520 ?? I 8:27PM 0:00.01 /bin/sh /usr/local/etc/rc.d/lcdproc.sh start root 6483 0.0 3.4 46428 17476 ?? SN 8:27PM 0:01.11 /usr/local/bin/php -f /usr/local/pkg/lcdproc_client.phpI didn't expect to see lcdproc.sh running, not that it's a problem.
Steve
Edit: I also so that the version of the sdeclcd driver is that with real time process priority set. Is that deliberate? That too should be no problem.
-
Hehe!
You're welcome Tix, let's see how much this version resists… I didn't have any problems since two days with 2 servers since almost 48h, but we need to share the data to consider it stable.
on both machines I use as driver sureelect, 1 second refresh, 8 screens on one and just 1 screen on the other one. The other options are left as default...
Ciao,
Michele -
Testing now.
One thing I have noticed that I didn't expect is:[2.0.1-RELEASE][root@pfsense.fire.box]/root(2): ps aux|grep lcd root 4965 0.0 0.3 3656 1520 ?? I 8:27PM 0:00.01 /bin/sh /usr/local/etc/rc.d/lcdproc.sh start root 6483 0.0 3.4 46428 17476 ?? SN 8:27PM 0:01.11 /usr/local/bin/php -f /usr/local/pkg/lcdproc_client.phpI didn't expect to see lcdproc.sh running, not that it's a problem.
Steve
Edit: I also so that the version of the sdeclcd driver is that with real time process priority set. Is that deliberate? That too should be no problem.
Hi Steve,
well, I removed the "lcdproc_client.sh" script, the one that managed the error counter for the client. lcdproc.sh is the one run to start/stop/restart the package. I honestly don't know why it is still running after it's launched to start the client, but it should not do anything.For the sdeclcd driver, we need to ask to fmertz if he asked to update the binary driver under files.pfsense.org, I guess not if it's not the last version. Anyway, probably after this message he will ask to update it.
Ciao,
Michele -
Hi Cino,
States (Not sure if other notice, it doesn't show the correct max, always 10000)
one day I'll swap to a different case so I can have a 20/4on my x86 pfSense 2.0.1 shows correctly 500000. I am afraid some char is hidden, but with a 20x2 display it should not… :S
Looking at the code, it looks it's able to read $config['system']['maximumstates']. How much did you set?
If you run on the the command prompt, php console, the following commands (copy/paste both), what result do you get?global $config; echo($config['system']['maximumstates']);Thanks,
Michele -
Not sure what went wrong but I went to add some additional screens and upon clicking save, the log shows the stopping and restarting but then stops again 1 sec later. This happens each time I enable/disable any screen.
Log capture:
Feb 10 18:23:42 pfsense LCDd: Client on socket 11 disconnected Feb 10 18:23:42 pfsense LCDd: sock_send: socket write error Feb 10 18:23:44 pfsense LCDd: Server shutting down on SIGTERM Feb 10 18:23:46 pfsense LCDd: LCDd version 0.5.3 starting Feb 10 18:23:46 pfsense LCDd: Using Configuration File: /usr/local/etc/LCDd.conf Feb 10 18:23:46 pfsense LCDd: Listening for queries on 127.0.0.1:13666 Feb 10 18:23:47 pfsense LCDd: Server shutting down on SIGTERM Feb 10 18:23:58 pfsense php: lcdproc: Failed to connect to LCDd process Operation timed out (60) Feb 10 18:24:09 pfsense php: lcdproc: Failed to connect to LCDd process Operation timed out (60) Feb 10 18:24:20 pfsense php: lcdproc: Failed to connect to LCDd process Operation timed out (60) Feb 10 18:24:31 pfsense php: lcdproc: Failed to connect to LCDd process Operation timed out (60)Trying to restart via the GUI does nothing (which I think is correct functionality) but running the start script from the shell seems to start the process again.
[root@pfsense]/root(2): /bin/sh /usr/local/etc/rc.d/lcdproc.sh start [root@pfsense]/root(6): ps aux | grep lcd <no results="">[root@pfsense]/root(7): ps aux | grep LCD root 25426 0.0 0.5 3524 1280 1 S+ 6:25PM 0:00.00 grep LCD [root@pfsense]/root(8): clog /var/log/system.log | grep LCD <snip>Feb 10 18:31:25 pfsense LCDd: LCDd version 0.5.3 starting Feb 10 18:31:25 pfsense LCDd: Using Configuration File: /usr/local/etc/LCDd.conf Feb 10 18:31:25 pfsense LCDd: Listening for queries on 127.0.0.1:13666 Feb 10 18:31:27 pfsense LCDd: Connect from host 127.0.0.1:49169 on socket 6</snip></no>So I'm now running these screens:
-Time
-Uptime
-Disk
-Load
-States
-Mbuf
-Interface Traffic (WAN)and these settings:
-ComPort=/dev/lpt0
-Display Size=2x20 display
-Driver=Firebox SDEC
-Refresh=5 sec
-All other settings are "default"Also, the Load average is staying higher around between 0.60 and 1.4 where prior to this update it stayed less than 0.80 (even when updating RRD). Again not sure it's related but I don't think it's anything to worry about.
Will continue to monitor…
-
the results were blank. I dont have anything set, left it for the system to decide. The dashboard says 299000.. I'll set a value and see what happens. Its been awhile since I looked at the lcdproc code, but I'm thinking there was default 10000 if nothing is set via the gui now that i think about it a little more
-
@tix
I can see from your logs that you still have 0.53 version of LCDd. So who knows what version of other files you have.
From my experience the 'reinstall package' button in the GUI does not seem to re download everything.
I suggest un-installing the package completely, checking for any left over files and then re-installing it.Steve
-
@tix
I can see from your logs that you still have 0.53 version of LCDd. So who knows what version of other files you have.
From my experience the 'reinstall package' button in the GUI does not seem to re download everything.
I suggest un-installing the package completely, checking for any left over files and then re-installing it.Steve
Well aren't I the idiot? :P Didn't even notice that….
Ok so I've now uninstalled the package, cleaned all the various references to LCDd, lcdproc, sdeclcd.so that the "find" command could locate. Then I reinstalled the package except LCDd is missing... Isn't this supplied by the lcdproc-dev package or am I being an idiot again?
-
@tix:
@tix
I can see from your logs that you still have 0.53 version of LCDd. So who knows what version of other files you have.
From my experience the 'reinstall package' button in the GUI does not seem to re download everything.
I suggest un-installing the package completely, checking for any left over files and then re-installing it.Steve
Well aren't I the idiot? :P Didn't even notice that….
Ok so I've now uninstalled the package, cleaned all the various references to LCDd, lcdproc, sdeclcd.so that the "find" command could locate. Then I reinstalled the package except LCDd is missing... Isn't this supplied by the lcdproc-dev package or am I being an idiot again?
Tix, LCDd is inside the package, very strange you don't have it… maybe a reboot between the uninstall and the reinstall could help..
-
the results were blank. I dont have anything set, left it for the system to decide. The dashboard says 299000.. I'll set a value and see what happens. Its been awhile since I looked at the lcdproc code, but I'm thinking there was default 10000 if nothing is set via the gui now that i think about it a little more
Ok, I've understood what happens… if there is nothing set the function just return 10000 as a constant.
I will fix this on the new version.Ciao,
Michele -
Hi Tix
@tix:Also, the Load average is staying higher around between 0.60 and 1.4 where prior to this update it stayed less than 0.80 (even when updating RRD). Again not sure it's related but I don't think it's anything to worry about.
Will continue to monitor…
well… as more screens you add, as more the client and LCDd have to work. If you only enable one screen the load should fall. The variables that affect the load are: number of screens, refresh rate.
Ciao,
Michele -
Hi Guys
Is it possible to ad this Lcd to
http://allnet.de/1577.html?&tx_mmallnetproductplugin_pi1[showUid]=421433&cHash=949c8a38a8
ftp://212.18.29.48/ftp/pub/allnet/utility-server/fw8888/lcm_server_1.0.tar.bz2i,m trying this for some time but with no success, see other posts from me
thx max
-
Hi Guys
Is it possible to ad this Lcd to
http://allnet.de/1577.html?&tx_mmallnetproductplugin_pi1[showUid]=421433&cHash=949c8a38a8
ftp://212.18.29.48/ftp/pub/allnet/utility-server/fw8888/lcm_server_1.0.tar.bz2i,m trying this for some time but with no success, see other posts from me
thx max
Hi Max (easyhugo),
it's impossible to know for me which driver this LCD panel uses… do you know the chipset? Can it use one of the drivers already made or you need another driver?Ciao,
Michele -
My German is very bad! :-[ (Only beaten by my non-existant Italian! ::))
However, according to [url=http://www.ipcop-forum.de/forum/viewtopic.php?f=22&t=26948#p231301]this post by IPCop ledgend Wintermute the display in the FW8888 is an LCM-162.
This doesn't appear to be supported directly by LCDproc but this blog post seems to show it is possible. That's quite old now so support maybe better integrated.
What drivers/versions have you tried?
Steve
Edit: This post confirms this.
-
Tix, LCDd is inside the package, very strange you don't have it… maybe a reboot between the uninstall and the reinstall could help..
I've tried multiple times to get LCDd to install and all fail. I must have broken something with the various versions and/or updates. I'll try a clean install later this weekend maybe….
In any case, I have the updated files now. I did a clean install to VMware Player and installed the package and then scp'd the file over to my real pfsense.
So far so good as I've exceeded my 10 hour limit and everything is working with the screens and settings I mentioned in the previous post.
-
@tix:
So far so good as I've exceeded my 10 hour limit and everything is working with the screens and settings I mentioned in the previous post.
hehe! on my machines I am running it from thursday with a refresh of 1second, and it's still working great… maybe I am too much optimist, but I think we made it... ;) at least for this specific problem!
-
Yes I think you have definitely solved the LCDd 100% problem. 48hours+ for me on two boxes running sdeclcd driver, 1second refresh, and screens: time, uptime and load.
Looking good. :)However I think the other problem is still present.
At boot or restarting packages when an IP change is detected the lcdproc package ends up being started and stopped multiple times. Before this could result in multiple clients running. I think this has been solved thanks to your kill loop. However today I switched on my resurected X-Core box and at the end of boot the LCDd daemon is running twice but with no client! :-\[2.0.1-RELEASE][root@x-core.localdomain]/root(2): ps aux | grep lcd root 17691 0.0 0.6 3656 1356 ?? IN 4:21PM 0:00.01 /bin/sh /usr/local/etc/rc.d/lcdproc.sh start [2.0.1-RELEASE][root@x-core.localdomain]/root(3): ps aux | grep LCD root 24707 0.0 0.5 3352 1148 ?? IN 4:21PM 0:00.01 /usr/local/sbin/LCDd -c /usr/local/etc/LCDd.conf nobody 24902 0.0 0.6 3368 1408 ?? SNs 4:21PM 0:00.21 /usr/local/sbin/LCDd -c /usr/local/etc/LCDd.confHere is the relavent section of the boot log:
Feb 12 16:22:33 apinger: Error while feeding rrdtool: Broken pipe Feb 12 16:21:52 LCDd: Listening for queries on 127.0.0.1:13666 Feb 12 16:21:52 LCDd: Using Configuration File: /usr/local/etc/LCDd.conf Feb 12 16:21:52 LCDd: LCDd version 0.5.5 starting Feb 12 16:21:49 LCDd: Server shutting down on SIGTERM Feb 12 16:21:49 LCDd: Listening for queries on 127.0.0.1:13666 Feb 12 16:21:49 LCDd: Using Configuration File: /usr/local/etc/LCDd.conf Feb 12 16:21:49 LCDd: LCDd version 0.5.5 starting Feb 12 16:21:47 php: lcdproc: Sync: End package sync Feb 12 16:21:47 php: lcdproc: Sync: Begin package sync Feb 12 16:21:47 LCDd: Server shutting down on SIGTERM Feb 12 16:21:47 php: lcdproc: Sync: End package sync Feb 12 16:21:45 LCDd: sock_send: socket write error Feb 12 16:21:45 LCDd: sock_send: socket write error Feb 12 16:21:45 LCDd: sock_send: socket write error Feb 12 16:21:45 LCDd: Client on socket 11 disconnected Feb 12 16:21:45 php: lcdproc: Sync: Restarting the service Feb 12 16:21:45 php: lcdproc: Sync: Begin package sync Feb 12 16:21:45 php: : Restarting/Starting all packages. Feb 12 16:21:42 check_reload_status: Reloading filter Feb 12 16:21:42 LCDd: Connect from host 127.0.0.1:11554 on socket 11 Feb 12 16:21:42 sshlockout[51329]: sshlockout/webConfigurator v3.0 starting up Feb 12 16:21:42 login: login on console as root Feb 12 16:21:41 php: lcdproc: Start client procedure. Error counter: (0) Feb 12 16:21:40 php: : IPSEC: One or more IPsec tunnel endpoints has changed its IP. Refreshing. Feb 12 16:21:40 LCDd: Listening for queries on 127.0.0.1:13666 Feb 12 16:21:40 LCDd: Using Configuration File: /usr/local/etc/LCDd.conf Feb 12 16:21:40 LCDd: LCDd version 0.5.5 starting Feb 12 16:21:39 check_reload_status: Starting packages Feb 12 16:21:39 php: : pfSense package system has detected an ip change 0.0.0.0 -> ... Restarting packages. Feb 12 16:21:39 php: : OpenNTPD is starting up. Feb 12 16:21:39 dnsmasq[44759]: ignoring nameserver 127.0.0.1 - local interface Feb 12 16:21:39 dnsmasq[44759]: ignoring nameserver 127.0.0.1 - local interface Feb 12 16:21:39 dnsmasq[44759]: using nameserver 192.168.1.1#53 Feb 12 16:21:39 dnsmasq[44759]: reading /etc/resolv.conf Feb 12 16:21:39 php: : The command '/usr/bin/killall 'ntpd'' returned exit code '1', the output was 'killall: warning: kill -TERM 51784: No such process' Feb 12 16:21:38 php: : Creating rrd update script Feb 12 16:21:38 php: : Resyncing OpenVPN instances for interface WAN. Feb 12 16:21:38 php: lcdproc: Sync: End package sync Feb 12 16:21:38 php: lcdproc: Sync: Begin package sync Feb 12 16:21:38 php: lcdproc: Sync: End package sync Feb 12 16:21:38 php: lcdproc: Sync: Begin package sync Feb 12 16:21:38 php: : Restarting/Starting all packages.It ends up starting and stopping 3 times.
Restarting the service again manually brings it back to normal.
Steve
