I need help choosing hardware for pfsense
-
but I run gigabit network to 50-60 clients on the local network?
How many interfaces do you use?
If you will need 1Gbps throughput then yes you will need a more powerful box.
Any i3 or i5 cpu will handle that. Even a low end Pentium or Celeron Sandy Bridge CPU will push 1Gbps.
For example: http://forum.pfsense.org/index.php/topic,45439.0.htmlSteve
-
There could also be some QoS upstream that you have no control over. And replacing your router will not change that.
UPDATE:
Here's a good read on the ISP QoS subject:
http://www.dslreports.com/forum/r27252457-Internet-Frontier-FIOS-Latency-and-QoS-Where-they-fail -
Hello and thank you for answering my question =)
I have two 24 port gigabit switches + 1 16 port switch Gigbit
these branches to about 40 different outlets in the house and the rest goes to the neighbor.
(all are not used) then it's a number of wireless clients that use the 5GHz band with N and ac connection.so i3 is good but should I use a dual intel card or two single or something else?
/ Chali
-
So you have three switches but how many NICs do you have in the pfSense box?
If you have each switch connected via a different NIC then traffic between them has to be routed by pfSense placing additional load on the box. If you only a single LAN NIC then only WAN<>LAN traffic is routed.It makes little difference to performance whether you use single or dual port NICs if you are using PCI-e cards. Single port NICs are usually far cheaper so if you have space for them use that.
The best regarded NICs are Intel server cards. You don't want to get one that is only recently released because there is a good chance it won't yet be supported by pfSense.
Steve
-
Hi
ok thanks for the answers =)
I connect the switches outside the router ( from switch to switch)
but you think it is ok to run on a i3 cpu? (type 3220 or 3240)
googled a bit on it and it seems that several had problems with i3 and pfsense 64-bit
I do not know if it whas old i3 or what vertion of pfsense./ Chali
-
There was a problem with the 64bit graphics driver for those cpus with built in gpu but I thought it had been fixed. You may have to run 2.1 Beta to get that. Otherwise just run 32bit. I'd be very suprised if you need more than 4GB RAM.
Read through the thread I linked to above. That user was able to get his full line speed (close to 1Gbps) using a Celeron G530 which is quite a bit less powerful than any i3.I have not built a box that powerful, I can only dream of getting a 1Gbps connection here! ;)
Steve
-
Hi igen
I got these following components.
(a bit exaggerated, but should hold for a while)Server MB Supermicro MBD-X9SCL-FO. (2xgig nic)
Intel Core i3-3240 Ivy Bridge - Box
8-gig ddr3 ram
80-gig ssd
And it is water cooled (really cool to say that the router is water cooled;-) )Now I'd like to het help finding a good gigabit NICs.
I understand that intel is preferable but which?
I would like to have 2-4 extra connections (two cards I guess) . but which have the smallest laytense?
(I play fps games and have a movie server that friends and family stream movies from)server I used before raised my laytense with 20-25 even when no one streamed movie.
and I do not want to have that again.(old server is this if it helps)
HP ProLiant DL380 G4:
2x Intel Xeon - 3,2GHz / 2M / 800FSB (64-bit)
3 GB DDR2 ECC
4x 36 GB Hotswap SCSI
Intel E7520 Chipset
2x 1 GB nicI can't afford like the worlds best nic (the budget is a bitt low)
I think I can afford around 400-500 dollars for 2 x 2 giga nic but as I said what should I choose?
(preferably cheaper only they can keep laytense at a low level and be stable)I am very grateful for any suggestions (I've been doing and fiddling with this for a long time, and it would be nice to get a solution to it finally)
Ps: im using google translate so sorry for the poor grammar
/ Sincerely Chali -
server I used before raised my laytense with 20-25
Do you mean latency rather than "laytense".
20-25 what? microseconds? milli seconds? seconds? etc
It is unlikely you would notice even 25 milli seconds.
-
Hi :)
Of course I mean milliseconds (I'll write it next time so everyone understands).
and yes it is ping / latency I mean.
for me it is absolutely noticeable whed such increase. (I usually have 20 in ping). but Whatever now, it is not that i am asking , but my question is simply what nic with the lowest latency for the amount I wrote.
(I'll still build so why not try to get it as good as possible?)Which of this do you think is best? (http://www.prisjakt.nu/produkt.php?j=928457,79419,785748)
ps: I use google translate as usual, so excuse the bad grammar and any errors in abbreviations that may exist.
/ Chali
-
Hi
I fonde this on the intel site (http://ark.intel.com/compare/50496,50490,50484,50483,50481,50398,50488,50486,50482,50497,50494,50491,50489,22191,22192,50495,50397,50396,49186,49185,49187,49184,59063,59062,59065,59064,68668)
I'm guessing that the i350 is the best way to go?
Butt is 1xt4. Better then 2xt2 cards?I have ordered two of these cards I hope it will be good http://www.proshop.se/Natverkskort-(adaptrar-osv.)/Intel-ETHERNET-I350-T2-SERVER-CTLR-2281784.html
/chali