APU-1D board throughput

astro_75

Hi all

Thank you for your feedbacks.

Yes you're right, there is no more CF Card for APU. I was wrong.

So the SD Card or mSata Drive have to be installed outside the enclosure (SD via USB). Is it right?
No more memory devices (SD, etc…) inside the enclosure?

Of course a fresh config after a fresh new installation would be the best solution.
But i have a lot of configs and want to use the Backup/Restore feature to spend a lot of time.

Tuning for the mbuf perhaps, enable PowerD is a must be!

Here you are over my knowledge about pfsense and nano. What is this exactly? ;-)

Many thanks
Astro

dotdash

@astro_75:

So the SD Card or mSata Drive have to be installed outside the enclosure (SD via USB). Is it right?
No more memory devices (SD, etc…) inside the enclosure?

The APU has an SD card slot. The procedure is the same as loading a CF card for an Alix- Use physdiskwrite or similar and insert the card into the unit, then assign interfaces via serial. I usually use the x64 nano version.

astro_75

Thanks!

I ordered this today:

1 apu1d4
APU.1D4 system board 4GB

1 case1d2blku
Enclosure 3 LAN, black, USB

1 ac12veur2
AC adapter 12V 2A euro for IT equipment

1 msata16d
SSD M-Sata 16GB MLC Phison

1 cr2032
Batt Li CR2032 w/ solder tails

And i will try to migrate from Alix to Apu. If it fails, i will config everything, step by step.

Just q new question now:

How can I/Should I install PfSense on the SSD?

With "Live CD with installer (On USB Memstick)" and this kind of nanoBSD Image: pfSense-memstick-serial-2.2.3-RELEASE-amd64.img.gz.
Is it right?

Thanks
Regards
Astro

Guest

With "Live CD with installer

On the mSATA or SSD

This kind of nanoBSD Image: pfSense-memstick-serial-2.2.3-RELEASE-amd64.img.gz

On the USB stick according to this two HowTo´s;

So it would be the best, led you by thoos HowTo`s to gain your goal, but the very best at first would be;

Windows, Linux or MacOS based Laptop or PC
serial to USB adapter or cable
USB stick
SD card
Win32DiskImager software
Putty or Kitty

If something fails or goes wrong, often this things would bring you out of the trap.
Nice to have, but not a must be, pfSense book from amazon and Internet connection for crawling pfSense Doc`s.

M_Devil

@astro_75: Did you receive your order and where you able to set it up?

Looking for likewise setup, so please share your expierence.

Guest

If it fails, i will config everything, step by step.

This would be also a really good choice, mostly not beloved by users, but the cleanest way.

How can I/Should I install PfSense on the SSD?

USB Stick or CD via PXE or TFT server.

astro_75

Hi Guys

Some news!

All HW received yesterday. As allways, tip top from pcengines.ch.

Today:

HW Assembly, msata Disk plugged, cooling installation (delivred with). (About 15 minits)
Installation of "pfSense-memstick-serial-2.2.3-RELEASE-amd64.img" on a USB Drive with Win32DiskImager-0.9.5 (About 22 seconds!)
Serial Console Access with PuTTy @115200 (15 seconds)
Booting the APU Board with USB Drive (Choose F12 to boot on it…) (15 seconds)
Following the instruction (2 minits)
Installation of PfSense on the msata Drive successfull (5 minits)
Configuration of the WAN Interface on rc0 (No other choice, unable to configure LAN and OPT Interfaces via console at this stage). (30 seconds)
Reboot! (30 seconds!)
Login as admin via https!
Enabling and configuring LAN and OPT Interfaces via webgui. (30 seconds)

Next step: Restore of ALL Settings!

2 ways: Restore via Recovery feature or manually (Probably proper and performance problem less)

Keep in touch.

One last thing for now: This APU Bord rocks! It is a Ferrari vs ALIX Board! ;-)

Guest

One last thing for now: This APU Bord rocks! It is a Ferrari vs ALIX Board! ;-)

setting up the baud rate fix to 115200on putty, at the Aolix APU and pfSnese comes with this even.
Activating TRIM Support
Activating PowerD with adaptive or high adaptive mode
perhaps if needed setting up higher mbufs numbers (3% till 4% of RAM is then in use)

astro_75

@astro_75:

2 ways: Restore via Recovery feature or manually (Probably proper and performance problem less)

3 ways actually!

I use the 3rd one: Using "High Avail. Sync" feature (Under Menu->System).

I sync the settings between the current Main FW (Alix Pfsense v2.2.2) and the new next one FW (APU Pfsense 2.2.3).
It works awesome!

The rest is done manually. Take some times, but refresh all the many features that Pfsense has!

astro_75

APU is now online as master. Alix as backup, in case of!
And it rocks!

Thanks all for your help!
Astro