Did you try to open it with curl like I showed above?

@Unoptanio said in ARP TABLE Refresh time for Wake On Lan: just add it in the /etc/sysctl.conf file? Nope, pfSense doesn't use that. The system tunables table replaces it so add it there if you need to.

@stephenw10 - Right? Thanks for all the help!!

There are several threads about boxes with N100 CPUs specifically where the default power settings in the BIOS interact unexpectedly with the speedshift driver in FreeBSD/pfSense.

@DominikHoffmann said in The oldest Netgate hardware still running pfSense+ 24.03?: it’s good to know that in 15 years my Netgate... By that time you may need a 128bit processor!

Responded in chat.

You would usually add VIPs (IPAlias) on the WAN for each additional public IP. Then change the outbound NAT rules to manual and add rules for the internal subnets via the appropriate VIP. https://docs.netgate.com/pfsense/en/latest/firewall/additional-ip-addresses.html#single-ip-subnet-on-wan Steve

@stephenw10 Memories! Nokia ip530

@Gertjan Thanks , the trick at the end was "just " the cert , it is not mentionned explicilty in the post with the command but part of the actions to make. For benefice of the Forum Q, command to run is certctl rehash This info is from PFsense Troublehoosting Manual Solved ! Thanks !

Mostly it gives you access to the pfSense Pus pkg repos. It's the entry level subscription that does so.

I rediscovered this today restoring two 3100 configs to 2100s. Short version, clicking Save before clicking Apply does work. Clicking Apply first results in an inaccessible router (aside from console).

@JeremyJ-0 said in how to stop logging blocked LAN IGMP?: Is there some part of the firewall that reads the rules on startup and does not re-read on a filter reload? Not that I am aware of. The reload of rules failing would explain your results however.

@Bob-Dig Sure, thanks. I plan to re-evaluate my values and start from scratch.

That fixed it the Gateway change did not transfer over to the floating traffic shaper access control lists so I had to resave them after that error is gone.

@Antibiotic said in ns8250: UART FCR is broken duirng boot OS: What did you add? I just used a 2 spare NAND gates to toggle one bit on board select. BTW, this is going back over 40 years to when I did that. The IMSAI was an S-100 bus computer. Various makes of S-100 bus computers were popular in the late 70s, until the IBM PC came out. They were generally used to run the CP/M operating system. BTW, I built that IMSAI from a kit, which was essentially bags of parts that had to be soldered to the circuit boards and then the system assembled.

@dgall Are you set to the 24.03 branch? If so, see https://docs.netgate.com/pfsense/en/latest/troubleshooting/upgrades.html#upgrade-not-offered-library-errors

@jeff3820 said in So why is my firewall logs full of mDNS pings that should pass??: Still looking for the sources... You most likely will need to sniff and see the mac address of the sender, then you should be able to at least get a clue to who it is by the maker via the first 3 of the mac, if its wired you can track that down to what port its plugged into. Wireless can block the mac and see who screams or what device stops working. You could do the same on pfsense, once you know the mac you can see what actual IP it has and that can be helpful, maybe it registered a name with dhcp, etc.

@stephenw10 Thanks again! I was able to change the config of lnav, so that it uses sh instead of bash. Now it is working!

I mean when you ran the pcap was it capturing all traffic or was it filtering by just a limited set of MAC addresses or IP addresses for example?