LAN client cannot connect

stephenw10

192.168.1.xxx

That is a private IP address there is no need to obscure it.

LANGW gateway: 192.168.100.1 status suspended

You should not have a gateway on LAN. Go to Interfaces > LAN and remove it.

Spectrum

@stephenw10 -General Configuration: enable interface
-Static IPv4 configuration: IPv4 address.
192.168.100.1/24
IPv4 Upstream gateway: none
-Reserved networks: Block private networks and loopback addresses and Block bogon networks (not active).

What exactly should I remove from these?

Spectrum

@stephenw10 i find how to eliminate gateway lan.. and i do. but pc is offline, life before rete5

stephenw10

Ok upstream gateway is correct.

Go to System > Routing > Gateways.

Make sure there is only WAN gateway. Remove a LAN gateway if it shows there.

Spectrum

@stephenw10 now i see only wan, not see lan in the System > Routing > Gateways.

stephenw10

Go to Diag > Routes.
Does it show a default route for IPv4 via the WAN gateway?

Spectrum

@stephenw10
i see default re0 (lan)
i dont see default in re1 (wan)

but

if i see ipv6 .. re1 (wan) is default

stephenw10

@Spectrum said in Hardware driver:

i see default re0 (lan)

Ok, that's bad. That's why it's broken.

Set the IPv4 default gateway to WAN_DHCP.

The delete the LAN gateway.

Spectrum

@stephenw10 good morning. last night i turned off pfsense and unplugged the wan cable, today i turned on and plugged the cable in and it gives me connected. i went into the settings it said and it no longer gives me re0 (lan) as default. i don't know what is going on in my settings, but i am sure if i turn off or reboot now it will give me the problem again. how can i save these settings?

IPv4 route
127.0.0.X lo0
192.168.1.X/24 re1 (wan)
192.168.1.XXX lo0
192.168.100.X/24 re0 (lan)
192.168.100.X lo0

Now only in ipv6 I see the wan in default, like this:
IPv6 route
default xxxxxxxx%re1 re1 (wan)

Spectrum

@Spectrum although it tells me "connected" pero any site comes up as impossible to access

Spectrum

@stephenw10 ok, now i set ipv4 and ipv6 gateway on the wan and it is no longer automatic.

stephenw10

Ok that's good. When it's set to automatic it may choose the LAN if the WAN goes down.

But you should not have a LAN gateway at all. You should delete it from there anyway.

Spectrum

@stephenw10 sistem/routing/gateway
WAN_DHCP Default (IPv4) WAN
WAN_DHCP6 Default (IPv6) WAN

Spectrum

@stephenw10 diag/routes
Route IPv4
default 192.168.1.xxx re1 (wan)
127.0.0.x lo0
192.168.1.x/24 re1 (wan)
192.168.1.xxx lo0
192.168.100.x/24 re0 (lan)
192.168.100.x lo0
Rotte IPv6
default xxxxxxxxxxxxxxxre1 re1 (wan)

Spectrum

@stephenw10 Status/Gateways

Gateways
WAN_DHCP (default) 192.168.1.xxx 192.168.1.xxx Connected Interface WAN_DHCP Gateway
WAN_DHCP6 (default) xxxx::xxx:xxxx:xxxx:xxxx%re1 xxxx::xxx:xxxx:xxxx:xxxx%re1 Connected Interface WAN_DHCP6 Gateway

Spectrum

@Spectrum do you suggest to delete this option in the lan network (re0)?

stephenw10

I'm only suggesting you delete any gateways defined on LAN in System > Routing > Gateways.

However it should be working as it is?

Spectrum

@stephenw10 sistem / routing / gateway have only wan . lan no longer appears. the pc is connected pero many sites can't access. i'm thinking maybe i need to see if it accepts both http and https. am i doing the thinking wrong?

Spectrum

@stephenw10 Unable to reach the site
Unable to find the IP address of the server of en.wikipedia.org.

Try:
Checking the connection
Checking the proxy, firewall, and DNS configuration
Running the Windows Network Diagnostics tool
ERR_NAME_NOT_RESOLVED

this i see when visite web like wikipedia

stephenw10

Can you ping 8.8.8.8 from pfSense?