LAN client cannot connect
-
Ok, great so pfSense cannot connect out.
So in the pfSense webgui check Status > Gateways.
I assume it shows 192.168.1.1 as the gateway?
Does it show the gateway as down?Go to Diag > Routes.
Does it show a default route for IPv4? -
@Spectrum wan WAN_DHCP6 (default) gateway: xxxxxxx status connect
WAN_DHCP gateway: 192.168.1.xxx status connect
LANGW gateway: 192.168.100.1 status suspended -
@Spectrum said in Hardware driver:
192.168.1.xxx
That is a private IP address there is no need to obscure it.
@Spectrum said in Hardware driver:
LANGW gateway: 192.168.100.1 status suspended
You should not have a gateway on LAN. Go to Interfaces > LAN and remove it.
-
@stephenw10 -General Configuration: enable interface
-Static IPv4 configuration: IPv4 address.
192.168.100.1/24
IPv4 Upstream gateway: none
-Reserved networks: Block private networks and loopback addresses and Block bogon networks (not active).What exactly should I remove from these?
-
@stephenw10 i find how to eliminate gateway lan.. and i do. but pc is offline, life before rete5
-
Ok upstream gateway is correct.
Go to System > Routing > Gateways.
Make sure there is only WAN gateway. Remove a LAN gateway if it shows there.
-
@stephenw10 now i see only wan, not see lan in the System > Routing > Gateways.
-
Go to Diag > Routes.
Does it show a default route for IPv4 via the WAN gateway? -
@stephenw10
i see default re0 (lan)
i dont see default in re1 (wan)but
if i see ipv6 .. re1 (wan) is default
-
@Spectrum said in Hardware driver:
i see default re0 (lan)
Ok, that's bad. That's why it's broken.
Set the IPv4 default gateway to WAN_DHCP.
The delete the LAN gateway.
-
@stephenw10 good morning. last night i turned off pfsense and unplugged the wan cable, today i turned on and plugged the cable in and it gives me connected. i went into the settings it said and it no longer gives me re0 (lan) as default. i don't know what is going on in my settings, but i am sure if i turn off or reboot now it will give me the problem again. how can i save these settings?
IPv4 route
127.0.0.X lo0
192.168.1.X/24 re1 (wan)
192.168.1.XXX lo0
192.168.100.X/24 re0 (lan)
192.168.100.X lo0Now only in ipv6 I see the wan in default, like this:
IPv6 route
default xxxxxxxx%re1 re1 (wan) -
@Spectrum although it tells me "connected" pero any site comes up as impossible to access
-
@stephenw10 ok, now i set ipv4 and ipv6 gateway on the wan and it is no longer automatic.
-
Ok that's good. When it's set to automatic it may choose the LAN if the WAN goes down.
But you should not have a LAN gateway at all. You should delete it from there anyway.
-
@stephenw10 sistem/routing/gateway
WAN_DHCP Default (IPv4) WAN
WAN_DHCP6 Default (IPv6) WAN -
@stephenw10 diag/routes
Route IPv4
default 192.168.1.xxx re1 (wan)
127.0.0.x lo0
192.168.1.x/24 re1 (wan)
192.168.1.xxx lo0
192.168.100.x/24 re0 (lan)
192.168.100.x lo0
Rotte IPv6
default xxxxxxxxxxxxxxxre1 re1 (wan) -
@stephenw10 Status/Gateways
Gateways
WAN_DHCP (default) 192.168.1.xxx 192.168.1.xxx Connected Interface WAN_DHCP Gateway
WAN_DHCP6 (default) xxxx::xxx:xxxx:xxxx:xxxx%re1 xxxx::xxx:xxxx:xxxx:xxxx%re1 Connected Interface WAN_DHCP6 Gateway -
@Spectrum do you suggest to delete this option in the lan network (re0)?
-
I'm only suggesting you delete any gateways defined on LAN in System > Routing > Gateways.
However it should be working as it is?
-
@stephenw10 sistem / routing / gateway have only wan . lan no longer appears. the pc is connected pero many sites can't access. i'm thinking maybe i need to see if it accepts both http and https. am i doing the thinking wrong?
