WPA_Supplicant

GPz1100

@stephenw10 ^^I believe it was 23.09 that introduced the new openssl.

It's unclear why the OP was unsuccessful with 2.70, given it does include the vlan0 patched wpa_supplicant with the same wpa_supplicant.conf

@AiC0315 said in WPA_Supplicant:

Failed to connect to non-global ctrl_ifname: (nil) error: No such file or directory

This error suggests a missing conf parameter in wpa_supplicant.conf, specifically

ctrl_interface=DIR=/var/run/wpa_supplicant

This goes ABOVE the "network={" array.

AiC0315

@GPz1100

I'll add that parameter when i have time and see what happens.

Thank you both for helping me try to figure this out

AiC0315

@GPz1100
Had time to mess with this last night. using this config.

ctrl_interface=DIR=/var/run/wpa_supplicant

eapol_version=1
ap_scan=0
fast_reauth=1
network={
ca_cert="/root/WPA/Certs/CA.pem"
client_cert="/root/WPA/Certs/Client.pem"
eap=TLS..
eapol_flags=0
identity="XX:XX:XX:XX:XX:XX" # Internet (ONT) interface MAC address must match this value
key_mgmt=IEEE8021X
phase1="allow_canned_success=1"
private_key="/root/WPA/Certs/PrivateKey.pem"
}
Works perfectly on 23.05.1 but does not get an IP on 2.7.0. Im using the wpa_supplicant posted on the dslforum link.
At this point I'm about to give up. Now I just have to dercide if I want to pay for plus from here on out

stephenw10

You tried using the included wpa_supplicant? 2.7 should have the patch to accept vlan0 by default.

GPz1100

@AiC0315 Where/when are you initializing wpa_supplicant?

AiC0315

@stephenw10
Yes, I used the wpa_supplicant file posted in the dslreports post

AiC0315

@GPz1100
/sbin/ifconfig igb0 ether "XX:XX:XX:XX:XX:XX" && /root/WPA/wpa_supplicant -B -Dwired -i igb0 -c /root/WPA/wpa_supplicant.conf -P/var/run/wpa_supplicant.pid && sleep 10 && /usr/sbin/wpa_cli logon. (early shellcmd)

wpa_cli logoff && sleep 10 && wpa_cli logon (shellcmd)

GPz1100

@AiC0315

What's the result of wpa_cli status in shell?

It should look something like this.

AiC0315

@GPz1100
Thanks,
I will take a look when I am able to install 2.7.0 back on my machine.

stephenw10

@AiC0315 said in WPA_Supplicant:

Yes, I used the wpa_supplicant file posted in the dslreports post

Yes I meant did you try the default wpa_supplicant version that's included in 2.7?

zC

@GPz1100 said in WPA_Supplicant:

@stephenw10 ^^I believe it was 23.09 that introduced the new openssl.

It's unclear why the OP was unsuccessful with 2.70, given it does include the vlan0 patched wpa_supplicant with the same wpa_supplicant.conf

@AiC0315 said in WPA_Supplicant:

Failed to connect to non-global ctrl_ifname: (nil) error: No such file or directory

This error suggests a missing conf parameter in wpa_supplicant.conf, specifically

ctrl_interface=DIR=/var/run/wpa_supplicant

This goes ABOVE the "network={" array.

What about

Failed to connect to non-global ctrl-ifname: (nil) error: Success

AiC0315

@stephenw10

Here is the output of wpa_cli status:

Selected interface 'igb0'
bssid=01:80:c2:00:00:03
freq=0
ssid=
id=0
mode=station
pairwise_cipher=NONE
group_cipher=NONE
key_mgmt=IEEE 802.1X (no WPA)
wpa_state=ASSOCIATED
address=
Supplicant PAE state=HELD
suppPortStatus=Unauthorized
EAP state=FAILURE
uuid=59fbef4f-

this was using the wpa_supplicant in 2.7.0.

henryzhou

Sorry for reopen such an old thread.
I'm running 24.03 but my eap tls authentication always failed.

My wpa_supplicant.conf is the same as the op (except the mac address)
I'm using the system build-in wpa_supplicant.

henryzhou

I also tried 23.09.1 and got the same result.
wpa_cli status shows
wpa_state=associated
supplicant pae state=held
suppPortStatus=Unauthorized
EAP state=FAILURE

Same certificate set works on Mikrotik.
I've checked the identity mac address which are the same.

Please help, it really drives me crazy

stephenw10

You are also trying to connect to AT&T?

henryzhou

@stephenw10 Yes, AT&T U-verse fiber. I confirm it's gpon not xgspon.

I also notice that the system has two wpa_supplicant. one is under /usr/sbin, the other under /usr/local/sbin. Both are version 2.10 and both failed the 1x authentication.

The system was originally running CE 2.7.2 and then upgrade to 23.09.1/24.03.

GPz1100

@henryzhou https://www.reddit.com/r/PFSENSE/comments/18jz0uc/installing_att_bypass_on_a_clean_install_of/

Follow the guide above. Additional settings are needed as pfsense 24.03 (and possibly earlier) uses openssl 3.0. Att's certs do not meet the minimum security standards so weaker ciphers must be allowed.

stephenw10

@GPz1100 said in WPA_Supplicant:

Att's certs do not meet the minimum security standards

Nice!

henryzhou

@GPz1100 Thank you so much.

After adding openssl_ciphers=DEFAULT@SECLEVEL=0 to my wpa_supplicant.conf and set OPENSSL_CONF to a customized config file it works.

I do appreciate your help. All of you.

GPz1100

@stephenw10 said in WPA_Supplicant:

Nice!

Don't shoot the messenger :). Technically, these certs are for internal use. I suppose these could be updated via firmware, but like most things att, doing so will probably create more damage than it solves.

Eventually gpon/eapol may fade away in favor of xgs and newer technologies.