2.8.2_1 blazer_usb, nutdrv_qx
This topic was forked from NUT Package (2.8.1 and above)
dennypage
-
Yes, I tried that, but without success.
After installing the old packages, as described by @incith, the UPS is immediately reconnected.
My current configuration is in the post above.
In addition, user=root is required. -
@LanterIT What specific packages do you have installed?
pkg info | grep nutDo you have any log entries for usbhid-ups from when you were running the current package?
-
pkg info | grep nut
nut-devel-2023.10.07_1 Network UPS Tools
pfSense-pkg-nut-2.8.2 Network UPS Tools -
less /var/log/dmesg.boot | grep usb usbus0 on xhci0 usbus0: 5.0Gbps Super Speed USB v3.0 ugen0.1: <Intel XHCI root HUB> at usbus0 uhub0 on usbus0 uhub0: <Intel XHCI root HUB, class 9/0, rev 3.00/1.00, addr 1> on usbus0 Root mount waiting for: usbus0 CAM ugen0.2: <PPC USB UPS> at usbus0 uhid0: <PPC USB UPS, class 0/0, rev 2.00/0.01, addr 1> on usbus0 ugen0.3: <vendor 0x0557 product 0x7000> at usbus0 uhub1: <vendor 0x0557 product 0x7000, class 9/0, rev 2.00/0.00, addr 2> on usbus0 Root mount waiting for: usbus0 CAM ugen0.4: <vendor 0x0557 product 0x2419> at usbus0 ukbd0: <vendor 0x0557 product 0x2419, class 0/0, rev 1.10/1.00, addr 3> on usbus0if there were more, where would the log entries be found?
-
@LanterIT said in NUT Package (2.8.1 and above):
if there were more, where would the log entries be found?
grep usbhid-ups /var/log/system.log -
no results
-
@LanterIT Sorry, my bad. I didn't notice that you had explicitly chosen the blazer driver.
grep blazer_usb /var/log/system.logBtw, I assume that you know that the blazer driver is deprecated and no longer being maintained post NUT 2.7.4 (April 2022). It is replaced by nutdrv_qx.
I would recommend that you switch to nutdrv_qx. And unless you have multiple UPSs attached to the system, you should be able to remove all the other settings in the Extra Arguments section other than pollinterval.
-
I have read that this driver is no longer supported.
So, I updated NUT package back to 2.8.2_1 and tried with the other driver as you suggested.
I only get the following error:
Poll UPS [ABB] failed - Driver not connectedDo you have any further advice on getting the UPS to work with the new driver?
In the meantime, I will revert to the old packages and settings.
-
@LanterIT said in NUT Package (2.8.1 and above):
So, I updated NUT package back to 2.8.2_1 and tried with the other driver as you suggested.
Have you tried the nutdrv_qx driver in 2.8.2?
What is the UPS you are using?
Can you post the output of "usbconfig -v" please?Thanks
-
@dennypage, thank you for your support!
Yes, I have tried it with version 2.8.2 and nutdrv_qx without success.
It is an ABB PowerValue 11 RT, as described in post 173.
usbconfig -v ugen0.1: <Intel XHCI root HUB> at usbus0, cfg=0 md=HOST spd=SUPER (5.0Gbps) pwr=SAVE (0mA) ugen0.1.0: uhub0: <Intel XHCI root HUB, class 9/0, rev 3.00/1.00, addr 1> bLength = 0x0012 bDescriptorType = 0x0001 bcdUSB = 0x0300 bDeviceClass = 0x0009 <HUB> bDeviceSubClass = 0x0000 bDeviceProtocol = 0x0003 bMaxPacketSize0 = 0x0009 idVendor = 0x0000 idProduct = 0x0000 bcdDevice = 0x0100 iManufacturer = 0x0001 <Intel> iProduct = 0x0002 <XHCI root HUB> iSerialNumber = 0x0000 <no string> bNumConfigurations = 0x0001 Configuration index 0 bLength = 0x0009 bDescriptorType = 0x0002 wTotalLength = 0x001f bNumInterfaces = 0x0001 bConfigurationValue = 0x0001 iConfiguration = 0x0000 <no string> bmAttributes = 0x0040 bMaxPower = 0x0000 Interface 0 bLength = 0x0009 bDescriptorType = 0x0004 bInterfaceNumber = 0x0000 bAlternateSetting = 0x0000 bNumEndpoints = 0x0001 bInterfaceClass = 0x0009 <HUB> bInterfaceSubClass = 0x0000 bInterfaceProtocol = 0x0000 iInterface = 0x0000 <no string> Endpoint 0 bLength = 0x0007 bDescriptorType = 0x0005 bEndpointAddress = 0x0081 <IN> bmAttributes = 0x0003 <INTERRUPT> wMaxPacketSize = 0x0002 bInterval = 0x00ff bRefresh = 0x0000 bSynchAddress = 0x0000 Additional Descriptor bLength = 0x06 bDescriptorType = 0x30 bDescriptorSubType = 0x00 RAW dump: 0x00 | 0x06, 0x30, 0x00, 0x00, 0x00, 0x00 ugen0.3: <vendor 0x0557 product 0x7000> at usbus0, cfg=0 md=HOST spd=HIGH (480Mbps) pwr=SAVE (100mA) ugen0.3.0: uhub1: <vendor 0x0557 product 0x7000, class 9/0, rev 2.00/0.00, addr 2> bLength = 0x0012 bDescriptorType = 0x0001 bcdUSB = 0x0200 bDeviceClass = 0x0009 <HUB> bDeviceSubClass = 0x0000 bDeviceProtocol = 0x0001 bMaxPacketSize0 = 0x0040 idVendor = 0x0557 idProduct = 0x7000 bcdDevice = 0x0000 iManufacturer = 0x0000 <no string> iProduct = 0x0000 <no string> iSerialNumber = 0x0000 <no string> bNumConfigurations = 0x0001 Configuration index 0 bLength = 0x0009 bDescriptorType = 0x0002 wTotalLength = 0x0019 bNumInterfaces = 0x0001 bConfigurationValue = 0x0001 iConfiguration = 0x0000 <no string> bmAttributes = 0x00e0 bMaxPower = 0x0032 Interface 0 bLength = 0x0009 bDescriptorType = 0x0004 bInterfaceNumber = 0x0000 bAlternateSetting = 0x0000 bNumEndpoints = 0x0001 bInterfaceClass = 0x0009 <HUB> bInterfaceSubClass = 0x0000 bInterfaceProtocol = 0x0000 iInterface = 0x0000 <no string> Endpoint 0 bLength = 0x0007 bDescriptorType = 0x0005 bEndpointAddress = 0x0081 <IN> bmAttributes = 0x0003 <INTERRUPT> wMaxPacketSize = 0x0001 bInterval = 0x000c bRefresh = 0x0000 bSynchAddress = 0x0000 ugen0.4: <vendor 0x0557 product 0x2419> at usbus0, cfg=0 md=HOST spd=LOW (1.5Mbps) pwr=ON (160mA) ugen0.4.0: ukbd0: <vendor 0x0557 product 0x2419, class 0/0, rev 1.10/1.00, addr 3> bLength = 0x0012 bDescriptorType = 0x0001 bcdUSB = 0x0110 bDeviceClass = 0x0000 <Probed by interface class> bDeviceSubClass = 0x0000 bDeviceProtocol = 0x0000 bMaxPacketSize0 = 0x0008 idVendor = 0x0557 idProduct = 0x2419 bcdDevice = 0x0100 iManufacturer = 0x0000 <no string> iProduct = 0x0000 <no string> iSerialNumber = 0x0000 <no string> bNumConfigurations = 0x0001 Configuration index 0 bLength = 0x0009 bDescriptorType = 0x0002 wTotalLength = 0x003b bNumInterfaces = 0x0002 bConfigurationValue = 0x0001 iConfiguration = 0x0000 <no string> bmAttributes = 0x00e0 bMaxPower = 0x0050 Interface 0 bLength = 0x0009 bDescriptorType = 0x0004 bInterfaceNumber = 0x0000 bAlternateSetting = 0x0000 bNumEndpoints = 0x0001 bInterfaceClass = 0x0003 <HID device> bInterfaceSubClass = 0x0001 bInterfaceProtocol = 0x0001 iInterface = 0x0000 <no string> Additional Descriptor bLength = 0x09 bDescriptorType = 0x21 bDescriptorSubType = 0x00 RAW dump: 0x00 | 0x09, 0x21, 0x00, 0x01, 0x00, 0x01, 0x22, 0x40, 0x08 | 0x00 Endpoint 0 bLength = 0x0007 bDescriptorType = 0x0005 bEndpointAddress = 0x0081 <IN> bmAttributes = 0x0003 <INTERRUPT> wMaxPacketSize = 0x0008 bInterval = 0x000a bRefresh = 0x0000 bSynchAddress = 0x0000 Interface 1 bLength = 0x0009 bDescriptorType = 0x0004 bInterfaceNumber = 0x0001 bAlternateSetting = 0x0000 bNumEndpoints = 0x0001 bInterfaceClass = 0x0003 <HID device> bInterfaceSubClass = 0x0001 bInterfaceProtocol = 0x0002 iInterface = 0x0000 <no string> Additional Descriptor bLength = 0x09 bDescriptorType = 0x21 bDescriptorSubType = 0x00 RAW dump: 0x00 | 0x09, 0x21, 0x00, 0x01, 0x00, 0x01, 0x22, 0x4f, 0x08 | 0x00 Endpoint 0 bLength = 0x0007 bDescriptorType = 0x0005 bEndpointAddress = 0x0082 <IN> bmAttributes = 0x0003 <INTERRUPT> wMaxPacketSize = 0x0006 bInterval = 0x0005 bRefresh = 0x0000 bSynchAddress = 0x0000 ugen0.2: <PPC USB UPS> at usbus0, cfg=0 md=HOST spd=FULL (12Mbps) pwr=ON (100mA) bLength = 0x0012 bDescriptorType = 0x0001 bcdUSB = 0x0200 bDeviceClass = 0x0000 <Probed by interface class> bDeviceSubClass = 0x0000 bDeviceProtocol = 0x0000 bMaxPacketSize0 = 0x0008 idVendor = 0x06da idProduct = 0x0005 bcdDevice = 0x0001 iManufacturer = 0x0001 <PPC> iProduct = 0x0002 <USB UPS > iSerialNumber = 0x0004 <retrieving string failed> bNumConfigurations = 0x0001 Configuration index 0 bLength = 0x0009 bDescriptorType = 0x0002 wTotalLength = 0x0022 bNumInterfaces = 0x0001 bConfigurationValue = 0x0001 iConfiguration = 0x0000 <no string> bmAttributes = 0x00c0 bMaxPower = 0x0032 Interface 0 bLength = 0x0009 bDescriptorType = 0x0004 bInterfaceNumber = 0x0000 bAlternateSetting = 0x0000 bNumEndpoints = 0x0001 bInterfaceClass = 0x0003 <HID device> bInterfaceSubClass = 0x0000 bInterfaceProtocol = 0x0000 iInterface = 0x0000 <no string> Additional Descriptor bLength = 0x09 bDescriptorType = 0x21 bDescriptorSubType = 0x11 RAW dump: 0x00 | 0x09, 0x21, 0x11, 0x01, 0x00, 0x01, 0x22, 0x1b, 0x08 | 0x00 Endpoint 0 bLength = 0x0007 bDescriptorType = 0x0005 bEndpointAddress = 0x0081 <IN> bmAttributes = 0x0003 <INTERRUPT> wMaxPacketSize = 0x0008 bInterval = 0x000a bRefresh = 0x0000 bSynchAddress = 0x0000And the last entry of usbconfig dump_device_quirks | grep HID_IGNORE
correspond the vendor and product ID:VID=0x06da PID=0x0005 REVLO=0x0000 REVHI=0xffff QUIRK=UQ_HID_IGNORE -
@LanterIT said in NUT Package (2.8.1 and above):
I have tried it with version 2.8.2 and nutdrv_qx without success.
Can you show the logs please?
grep nutdrv_qx /var/log/system.logThanks
-
output of grep nutdrv_qx /var/log/system.log:
Feb 18 20:46:46 gw1 upsd[95065]: Can't connect to UPS [ABB] (nutdrv_qx-ABB): No such file or directory Feb 18 20:48:15 gw1 upsd[13980]: Can't connect to UPS [ABB] (nutdrv_qx-ABB): No such file or directory Feb 18 20:50:52 gw1 upsd[97140]: Can't connect to UPS [ABB] (nutdrv_qx-ABB): No such file or directory Feb 18 20:54:33 gw1 upsd[90641]: Can't connect to UPS [ABB] (nutdrv_qx-ABB): No such file or directory Feb 18 21:01:24 gw1 upsd[82217]: Can't connect to UPS [ABB] (nutdrv_qx-ABB): No such file or directory Feb 18 21:06:13 gw1 upsd[73902]: Can't connect to UPS [ABB] (nutdrv_qx-ABB): No such file or directory Feb 18 21:09:43 gw1 upsd[67092]: Can't connect to UPS [ABB] (nutdrv_qx-ABB): No such file or directory Feb 18 21:14:36 gw1 upsd[5940]: Can't connect to UPS [ABB] (nutdrv_qx-ABB): No such file or directory Feb 18 21:15:59 gw1 upsd[20566]: Can't connect to UPS [ABB] (nutdrv_qx-ABB): No such file or directory Feb 18 21:16:34 gw1 upsd[68768]: Can't connect to UPS [ABB] (nutdrv_qx-ABB): No such file or directory Feb 18 21:20:15 gw1 upsd[599]: Can't connect to UPS [ABB] (nutdrv_qx-ABB): No such file or directory Feb 19 10:31:13 gw1 upsd[22401]: Can't connect to UPS [ABB] (nutdrv_qx-ABB): No such file or directory Feb 19 10:31:43 gw1 upsd[99457]: Can't connect to UPS [ABB] (nutdrv_qx-ABB): No such file or directory Feb 19 10:32:41 gw1 upsd[7578]: Can't connect to UPS [ABB] (nutdrv_qx-ABB): No such file or directory Feb 19 18:07:05 gw1 upsd[28139]: Can't connect to UPS [ABB] (nutdrv_qx-ABB): No such file or directoryThanks
-
@LanterIT Unfortunately there are no log entries from the nutdrv_qx process. If you are comfortable with it, could you try the following please?
First, this insures that the nut service is running:
/usr/local/etc/rc.d/nut.sh restartThis kills any driver that may be running:
killall nutdrv_qxThis starts the nutdrv_qx driver in debug mode:
/usr/local/libexec/nut/nutdrv_qx -D -a ABBThe driver will output debug information in the shell. Let it run for a few seconds, then you can kill it. Please post the output. Thanks.
-
The driver stops after a few seconds. Output with triple D:
/usr/local/libexec/nut/nutdrv_qx -DDD -a ABB Network UPS Tools - Generic Q* USB/Serial driver 0.36 (2.8.1.1) USB communication driver (libusb 1.0) 0.46 0.000000 [D3] main_arg: var='driver' val='nutdrv_qx' 0.000037 [D3] main_arg: var='port' val='auto' 0.000083 [D3] main_arg: var='pollinterval' val='10' 0.000096 [D1] testval_reloadable: setting 'pollinterval' exists and differs: new value '10' vs. '2' 0.000135 [D1] Network UPS Tools version 2.8.1.1 (release/snapshot of 2.8.1.1) built with FreeBSD clang version 16.0.6 (https://github.com/llvm/llvm-project.git llvmorg-16.0.6-0-g7cbf1a259152); Target: x86_64-unknown-freebsd14.0; Thread model: posix and configured with flags: --sysconfdir=/usr/local/etc/nut --program-transform-name= --localstatedir=/var/db/nut --datadir=/usr/local/etc/nut --with-devd-dir=/usr/local/etc/devd --with-drvpath=/usr/local/libexec/nut --with-statepath=/var/db/nut --with-altpidpath=/var/db/nut --with-pidpath=/var/db/nut --with-pkgconfig-dir=/usr/local/libdata/pkgconfig --with-user=nut --with-group=nut --with-python=/usr/local/bin/python3.11 --without-python2 --with-python3=/usr/local/bin/python3.11 --without-nut_monitor --with-ltdl --with-nut-scanner --with-avahi --with-cgi --with-cgipath=/usr/local/www/cgi-bin/nut --with-htmlpath=/usr/local/www/nut --with-gd-includes=-I/usr/local/include --with-gd-libs='-L/usr/local/lib -lgd' --without-dev --with-freeipmi --without-ipmi --with-doc=no --with-modbus --with-neon --without-nss --with-openssl --with-powerman --with-serial --with-snmp --with-usb=auto --prefix=/usr/local --mandir=/usr/local/man --disable-silent-rules --infodir=/usr/local/share/info/ --build=amd64-portbld-freebsd14.0 0.000156 [D1] debug level is '3' 0.000861 [D1] Succeeded to become_user(nut): now UID=316 GID=316 0.000956 [D1] upsdrv_initups... 0.001271 [D2] Checking device 1 of 1 (06DA/0005) 0.003392 [D1] nut_libusb_open get iSerialNumber failed, retrying... 0.004140 [D1] nut_libusb_open get iSerialNumber failed, retrying... 0.004766 [D1] nut_libusb_open get iSerialNumber failed, retrying... 0.004770 [D2] - VendorID: 06da 0.004772 [D2] - ProductID: 0005 0.004774 [D2] - Manufacturer: PPC 0.004776 [D2] - Product: USB UPS 0.004778 [D2] - Serial Number: unknown 0.004780 [D2] - Bus: 000 0.004782 [D2] - Bus Port: 007 0.004784 [D2] - Device: 002 0.004786 [D2] - Device release number: 0001 0.004788 [D2] Trying to match device 0.004791 [D3] match_function_regex: matching a device... 0.004794 [D2] Device matches 0.004796 [D2] Reading configuration descriptor 1 of 1 0.004823 [D3] libusb_kernel_driver_active() returned 0: Success 0.004827 [D2] Claimed interface 0 successfully 0.004830 [D3] nut_usb_set_altinterface: skipped libusb_set_interface_alt_setting(udev, 0, 0) 0.005027 [D3] send: QGS 0.049762 [D3] read: 0.049799 [D2] qx_process_answer: short reply (input.voltage) 0.050013 [D3] send: QGS 0.089767 [D3] read: 0.089777 [D2] qx_process_answer: short reply (input.voltage) 0.089979 [D3] send: QGS 0.129766 [D3] read: 0.129778 [D2] qx_process_answer: short reply (input.voltage) 0.129981 [D3] send: M 0.153762 [D3] read: 0.153784 [D2] voltronic_qs_protocol: invalid protocol [] 0.153991 [D3] send: M 0.177763 [D3] read: 0.177774 [D2] voltronic_qs_protocol: invalid protocol [] 0.177986 [D3] send: M 0.201763 [D3] read: 0.201773 [D2] voltronic_qs_protocol: invalid protocol [] 0.201986 [D3] send: M 0.225765 [D3] read: 0.225788 [D2] voltronic_qs_hex_protocol: invalid protocol [] 0.225985 [D3] send: M 0.249776 [D3] read: 0.249791 [D2] voltronic_qs_hex_protocol: invalid protocol [] 0.249988 [D3] send: M 0.273768 [D3] read: 0.273782 [D2] voltronic_qs_hex_protocol: invalid protocol [] 0.273982 [D3] send: QS 0.313767 [D3] read: 0.313797 [D2] qx_process_answer: short reply (input.voltage) 0.314003 [D3] send: QS 0.353768 [D3] read: 0.353780 [D2] qx_process_answer: short reply (input.voltage) 0.353996 [D3] send: QS 0.393768 [D3] read: 0.393778 [D2] qx_process_answer: short reply (input.voltage) 0.393988 [D3] send: D 0.425762 [D3] read: 0.425781 [D2] qx_process_answer: short reply (input.voltage) 0.425981 [D3] send: D 0.457770 [D3] read: 0.457781 [D2] qx_process_answer: short reply (input.voltage) 0.457990 [D3] send: D 0.489781 [D3] read: 0.489802 [D2] qx_process_answer: short reply (input.voltage) 0.490024 [D3] send: Q1 0.721777 [D3] read: 0.721795 [D2] qx_process_answer: input.voltage - invalid start character [00], expected [28] 0.722003 [D3] send: Q1 0.953777 [D3] read: 0.953800 [D2] qx_process_answer: input.voltage - invalid start character [00], expected [28] 0.954010 [D3] send: Q1 1.185762 [D3] read: 1.185783 [D2] qx_process_answer: input.voltage - invalid start character [00], expected [28] 1.185993 [D3] send: Q1 1.417766 [D3] read: 1.417800 [D2] qx_process_answer: input.voltage - invalid start character [00], expected [28] 1.418004 [D3] send: Q1 1.649787 [D3] read: 1.649811 [D2] qx_process_answer: input.voltage - invalid start character [00], expected [28] 1.650018 [D3] send: Q1 1.881787 [D3] read: 1.881813 [D2] qx_process_answer: input.voltage - invalid start character [00], expected [28] 1.882028 [D3] send: Q1 2.113780 [D3] read: 2.113818 [D2] qx_process_answer: input.voltage - invalid start character [00], expected [28] 2.114032 [D3] send: Q1 2.345805 [D3] read: 2.345826 [D2] qx_process_answer: input.voltage - invalid start character [00], expected [28] 2.346033 [D3] send: Q1 2.577789 [D3] read: 2.577811 [D2] qx_process_answer: input.voltage - invalid start character [00], expected [28] 2.578025 [D3] send: Q1 2.809783 [D3] read: 2.809816 [D2] qx_process_answer: input.voltage - invalid start character [00], expected [28] 2.810032 [D3] send: Q1 3.041789 [D3] read: 3.041813 [D2] qx_process_answer: input.voltage - invalid start character [00], expected [28] 3.042029 [D3] send: Q1 3.273790 [D3] read: 3.273808 [D2] qx_process_answer: input.voltage - invalid start character [00], expected [28] 3.274022 [D3] send: WH 3.313764 [D3] read: 3.313794 [D2] qx_process_answer: short reply (experimental.series) 3.313802 [D2] claim: cannot process experimental.series 3.314007 [D3] send: WH 3.353785 [D3] read: 3.353796 [D2] qx_process_answer: short reply (experimental.series) 3.353802 [D2] claim: cannot process experimental.series 3.354023 [D3] send: WH 3.393800 [D3] read: 3.393816 [D2] qx_process_answer: short reply (experimental.series) 3.393824 [D2] claim: cannot process experimental.series 3.394039 [D3] send: Q1 3.625780 [D3] read: 3.625821 [D2] qx_process_answer: input.voltage - invalid start character [00], expected [28] 3.626044 [D3] send: Q1 3.857800 [D3] read: 3.857818 [D2] qx_process_answer: input.voltage - invalid start character [00], expected [28] 3.858031 [D3] send: Q1 4.089798 [D3] read: 4.089820 [D2] qx_process_answer: input.voltage - invalid start character [00], expected [28] 4.090036 [D3] send: Q1 4.321792 [D3] read: 4.321831 [D2] qx_process_answer: input.voltage - invalid start character [00], expected [28] 4.322044 [D3] send: Q1 4.553794 [D3] read: 4.553810 [D2] qx_process_answer: input.voltage - invalid start character [00], expected [28] 4.554013 [D3] send: Q1 4.785797 [D3] read: 4.785820 [D2] qx_process_answer: input.voltage - invalid start character [00], expected [28] 4.786030 [D3] send: Q1 5.017814 [D3] read: 5.017856 [D2] qx_process_answer: input.voltage - invalid start character [00], expected [28] 5.018080 [D3] send: Q1 5.249798 [D3] read: 5.249816 [D2] qx_process_answer: input.voltage - invalid start character [00], expected [28] 5.250031 [D3] send: Q1 5.481806 [D3] read: 5.481827 [D2] qx_process_answer: input.voltage - invalid start character [00], expected [28] 5.481836 Device not supported! 5.481843 Device not supported! 5.481892 upsnotify: failed to notify about state 4: no notification tech defined, will not spam more about it -
@LanterIT said in NUT Package (2.8.1 and above):
The driver stops after a few seconds. Output with triple D:
Very useful. When you tried the nutdrv_qx driver, did you still have anything in the "Extra Arguments to driver" section?
Assuming not, can you test with this content in the "Extra Arguments to driver" section please?
vendorid=06da productid=0005 subdriver = "phoenix" protocol = "megatec" -
Thank you for your help.
I am pleased that you have found the cause in the tripplite_usb driver.First only the pollinterval, then with all "old" arguments.
Could it also be related to the serial number?
0.003392 [D1] nut_libusb_open get iSerialNumber failed, retrying... 0.004140 [D1] nut_libusb_open get iSerialNumber failed, retrying... 0.004766 [D1] nut_libusb_open get iSerialNumber failed, retrying... -
@LanterIT said in NUT Package (2.8.1 and above):
And the last entry of usbconfig dump_device_quirks | grep HID_IGNORE
correspond the vendor and product ID:VID=0x06da PID=0x0005 REVLO=0x0000 REVHI=0xffff QUIRK=UQ_HID_IGNORE
Btw, a quirk is only necessary if the device is HID compliant. The quirk prevents the OS from attaching a default HID driver. If the UPS is actually HID compliant, usbhid-ups would be the preferred driver. I assume that the usbhid-ups driver did not work, correct?
-
@LanterIT said in NUT Package (2.8.1 and above):
First only the pollinterval, then with all "old" arguments.
Just with the content above please, and the test you ran previously:
/usr/local/libexec/nut/nutdrv_qx -DDD -a ABBThanks
-
/usr/local/libexec/nut/nutdrv_qx -DDD -a ABB Network UPS Tools - Generic Q* USB/Serial driver 0.36 (2.8.0.1) USB communication driver (libusb 1.0) 0.46 0.000000 [D3] main_arg: var='driver' val='nutdrv_qx' 0.000033 [D3] main_arg: var='port' val='auto' 0.000050 [D3] main_arg: var='vendorid' val='06da' 0.000074 [D3] main_arg: var='productid' val='0005' 0.000092 [D3] main_arg: var='subdriver' val='phoenix' 0.000108 [D3] main_arg: var='protocol' val='megatec' 0.000144 [D1] Network UPS Tools version 2.8.0.1 (release/snapshot of 2.8.0.1) built with FreeBSD clang version 16.0.6 (https://github.com/llvm/llvm-project.git llvmorg-16.0.6-0-g7cbf1a259152); Target: x86_64-unknown-freebsd14.0; Thread model: posix and configured with flags: --sysconfdir=/usr/local/etc/nut --program-transform-name= --localstatedir=/var/db/nut --datadir=/usr/local/etc/nut --with-devd-dir=/usr/local/etc/devd --with-drvpath=/usr/local/libexec/nut --with-statepath=/var/db/nut --with-altpidpath=/var/db/nut --with-pidpath=/var/db/nut --with-pkgconfig-dir=/usr/local/libdata/pkgconfig --with-user=nut --with-group=nut --with-python=/usr/local/bin/python3.11 --without-python2 --with-python3=/usr/local/bin/python3.11 --with-ltdl --with-nut-scanner --with-avahi --with-cgi --with-cgipath=/usr/local/www/cgi-bin/nut --with-htmlpath=/usr/local/www/nut --with-gd-includes=-I/usr/local/include --with-gd-libs='-L/usr/local/lib -lgd' --without-dev --with-freeipmi --without-ipmi --with-doc=no --with-modbus --with-neon --without-nss --with-openssl --with-powerman --with-serial --with-snmp --with-usb=auto --prefix=/usr/local --mandir=/usr/local/man --disable-silent-rules --infodir=/usr/local/share/info/ --build=amd64-portbld-freebsd14.0 0.000163 [D1] debug level is '3' 0.000845 [D1] Succeeded to become_user(nut): now UID=316 GID=316 0.000936 [D1] upsdrv_initups... 0.001331 [D2] Checking device 1 of 1 (06DA/0005) 0.001525 [D1] nut_libusb_open: invalid libusb bus number 0 0.003757 [D1] nut_libusb_open get iSerialNumber failed, retrying... 0.004506 [D1] nut_libusb_open get iSerialNumber failed, retrying... 0.005134 [D1] nut_libusb_open get iSerialNumber failed, retrying... 0.005144 [D2] - VendorID: 06da 0.005151 [D2] - ProductID: 0005 0.005157 [D2] - Manufacturer: PPC 0.005163 [D2] - Product: USB UPS 0.005169 [D2] - Serial Number: unknown 0.005175 [D2] - Bus: ▒▒▒▒▒▒▒▒002 0.005182 [D2] - Bus Port: 007 0.005187 [D2] - Device: 002 0.005193 [D2] - Device release number: 0001 0.005199 [D2] Trying to match device 0.005205 [D3] match_function_regex: matching a device... 0.005234 [D2] Device matches 0.005240 [D2] Reading first configuration descriptor 0.005304 [D3] libusb_kernel_driver_active() returned 0: Success 0.005316 [D2] Claimed interface 0 successfully 0.005325 [D3] nut_usb_set_altinterface: skipped libusb_set_interface_alt_setting(udev, 0, 0) 0.005355 [D2] Skipping protocol Voltronic 0.08 0.005362 [D2] Skipping protocol Voltronic-QS 0.09 0.005368 [D2] Skipping protocol Voltronic-QS-Hex 0.10 0.005374 [D2] Skipping protocol Mustek 0.08 0.005381 [D2] Skipping protocol Megatec/old 0.08 0.005387 [D2] Skipping protocol BestUPS 0.07 0.005393 [D2] Skipping protocol Mecer 0.08 0.062217 [D3] send: Q1 0.294022 [D3] read: (225.4 225.4 229.9 050 50.0 2.18 28.2 00000001 1.310822 [D3] flush: Timeout (-7) 1.311048 [D3] send: I 1.366114 [D3] read: 1.366148 [D2] qx_process_answer: short reply (ups.firmware) 1.430347 [D3] send: Q1 1.662015 [D3] read: (225.4 225.4 230.4 047 49.9 2.18 28.2 00000001 2.695886 [D3] flush: Timeout (-7) 2.696121 [D3] send: I 2.758125 [D3] read: 2.758151 [D2] qx_process_answer: short reply (ups.firmware) 2.822248 [D3] send: Q1 3.054034 [D3] read: (225.9 225.9 229.7 047 49.9 2.18 28.2 00000001 4.064734 [D3] flush: Timeout (-7) 4.064958 [D3] send: I 4.126133 [D3] read: 4.126151 [D2] qx_process_answer: short reply (ups.firmware) 4.126167 [D2] Skipping protocol Zinto 0.07 4.126175 [D2] Skipping protocol Masterguard 0.02 4.126181 [D2] Skipping protocol Hunnox 0.02 4.126188 [D2] Skipping protocol Ablerex 0.01 4.126194 [D2] Skipping protocol Q1 0.08 4.126200 Device not supported! 4.126206 Device not supported! 4.126247 upsnotify: failed to notify about state 4: no notification tech defined, will not spam more about itlet me upgrade to the new package...
-
... and with version 2.8.2_1:
/usr/local/libexec/nut/nutdrv_qx -DDD -a ABB Network UPS Tools - Generic Q* USB/Serial driver 0.36 (2.8.1.1) USB communication driver (libusb 1.0) 0.46 0.000000 [D3] main_arg: var='driver' val='nutdrv_qx' 0.000012 [D3] main_arg: var='port' val='auto' 0.000017 [D3] main_arg: var='vendorid' val='06da' 0.000025 [D3] main_arg: var='productid' val='0005' 0.000031 [D3] main_arg: var='subdriver' val='phoenix' 0.000036 [D3] main_arg: var='protocol' val='megatec' 0.000046 [D1] Network UPS Tools version 2.8.1.1 (release/snapshot of 2.8.1.1) built with FreeBSD clang version 16.0.6 (https://github.com/llvm/llvm-project.git llvmorg-16.0.6-0-g7cbf1a259152); Target: x86_64-unknown-freebsd14.0; Thread model: posix and configured with flags: --sysconfdir=/usr/local/etc/nut --program-transform-name= --localstatedir=/var/db/nut --datadir=/usr/local/etc/nut --with-devd-dir=/usr/local/etc/devd --with-drvpath=/usr/local/libexec/nut --with-statepath=/var/db/nut --with-altpidpath=/var/db/nut --with-pidpath=/var/db/nut --with-pkgconfig-dir=/usr/local/libdata/pkgconfig --with-user=nut --with-group=nut --with-python=/usr/local/bin/python3.11 --without-python2 --with-python3=/usr/local/bin/python3.11 --without-nut_monitor --with-ltdl --with-nut-scanner --with-avahi --with-cgi --with-cgipath=/usr/local/www/cgi-bin/nut --with-htmlpath=/usr/local/www/nut --with-gd-includes=-I/usr/local/include --with-gd-libs='-L/usr/local/lib -lgd' --without-dev --with-freeipmi --without-ipmi --with-doc=no --with-modbus --with-neon --without-nss --with-openssl --with-powerman --with-serial --with-snmp --with-usb=auto --prefix=/usr/local --mandir=/usr/local/man --disable-silent-rules --infodir=/usr/local/share/info/ --build=amd64-portbld-freebsd14.0 0.000053 [D1] debug level is '3' 0.000241 [D1] Succeeded to become_user(nut): now UID=316 GID=316 0.000268 [D1] upsdrv_initups... 0.000387 [D2] Checking device 1 of 1 (06DA/0005) 0.002373 [D1] nut_libusb_open get iSerialNumber failed, retrying... 0.002998 [D1] nut_libusb_open get iSerialNumber failed, retrying... 0.003622 [D1] nut_libusb_open get iSerialNumber failed, retrying... 0.003625 [D2] - VendorID: 06da 0.003627 [D2] - ProductID: 0005 0.003628 [D2] - Manufacturer: PPC 0.003630 [D2] - Product: USB UPS 0.003632 [D2] - Serial Number: unknown 0.003634 [D2] - Bus: 000 0.003636 [D2] - Bus Port: 007 0.003637 [D2] - Device: 002 0.003639 [D2] - Device release number: 0001 0.003641 [D2] Trying to match device 0.003643 [D3] match_function_regex: matching a device... 0.003652 [D2] Device matches 0.003654 [D2] Reading configuration descriptor 1 of 1 0.003671 [D3] libusb_kernel_driver_active() returned 0: Success 0.003675 [D2] Claimed interface 0 successfully 0.003677 [D3] nut_usb_set_altinterface: skipped libusb_set_interface_alt_setting(udev, 0, 0) 0.003686 [D2] Skipping protocol Voltronic 0.08 0.003688 [D2] Skipping protocol Voltronic-QS 0.09 0.003691 [D2] Skipping protocol Voltronic-QS-Hex 0.10 0.003693 [D2] Skipping protocol Mustek 0.08 0.003695 [D2] Skipping protocol Megatec/old 0.08 0.003696 [D2] Skipping protocol BestUPS 0.07 0.003698 [D2] Skipping protocol Mecer 0.08 0.066547 [D3] send: Q1 0.306233 [D3] read: (225.0 225.0 229.7 048 49.9 2.18 28.3 00000001 1.317829 [D3] flush: Timeout (-7) 1.318054 [D3] send: I 1.378224 [D3] read: 1.378268 [D2] qx_process_answer: short reply (ups.firmware) 1.442558 [D3] send: Q1 1.682233 [D3] read: (224.8 224.8 229.7 048 49.9 2.18 28.3 00000001 2.702010 [D3] flush: Timeout (-7) 2.702232 [D3] send: I 2.762328 [D3] read: 2.762343 [D2] qx_process_answer: short reply (ups.firmware) 2.826570 [D3] send: Q1 3.066243 [D3] read: (225.0 225.0 229.1 047 49.9 2.18 28.3 00000001 4.081737 [D3] flush: Timeout (-7) 4.081959 [D3] send: I 4.146236 [D3] read: 4.146251 [D2] qx_process_answer: short reply (ups.firmware) 4.146266 [D2] Skipping protocol Zinto 0.07 4.146274 [D2] Skipping protocol Masterguard 0.02 4.146281 [D2] Skipping protocol Hunnox 0.02 4.146287 [D2] Skipping protocol Ablerex 0.01 4.146294 [D2] Skipping protocol Q1 0.08 4.146299 Device not supported! 4.146305 Device not supported! 4.146346 upsnotify: failed to notify about state 4: no notification tech defined, will not spam more about itlooks pretty much the same.
