Intel NIC I-226V

stephenw10

No.
However what is seemingly quite common with those N100/N200 CPUs is the speed/power values passed by the BIOS result in slow running. Check the CPU frequency reported during the test.

Antibiotic

@stephenw10 during speed test result:
Intel(R) N100
Current: 2922 MHz, Max: 806 MHz
4 CPUs: 1 package(s) x 4 core(s)
AES-NI CPU Crypto: Yes (active)

Antibiotic

@stephenw10 Power Savings - Intel Speed Shift
Speed ShiftEnable Speed Shift

Current State: Active
Control Level
Core Level Control (Recommended)

Core-level control is the best practice in most cases, especially for hardware with only a single physical CPU. Changing this setting requires a reboot.

Current Active Level: Core
Power PreferencePerformanceEnergy Efficiency
50

stephenw10

Mmm, OK. That seems good.
I'd also try runing top -HaSP whist testing to see the per core CPU load at the time.

Antibiotic

@stephenw10 Power Savings - PowerD
PowerD Disabled
AC Power
Hiadaptive
Battery Power
Hiadaptive
Unknown Power
Hiadaptive

Antibiotic

@stephenw10 last pid: 68860; load averages: 1.30, 1.05, 0.95 up 0+02:02:23 16:41:57
387 threads: 5 running, 358 sleeping, 24 waiting
CPU 0: 13.8% user, 0.0% nice, 25.2% system, 4.3% interrupt, 56.7% idle
CPU 1: 19.7% user, 0.0% nice, 18.1% system, 9.1% interrupt, 53.1% idle
CPU 2: 23.6% user, 0.0% nice, 17.3% system, 5.9% interrupt, 53.1% idle
CPU 3: 15.4% user, 0.0% nice, 21.7% system, 9.4% interrupt, 53.5% idle
Mem: 513M Active, 1025M Inact, 2057M Wired, 56K Buf, 12G Free
ARC: 539M Total, 270M MFU, 248M MRU, 1661K Anon, 2880K Header, 15M Other
461M Compressed, 1156M Uncompressed, 2.51:1 Ratio
Swap: 1024M Total, 1024M Free

Antibiotic

@stephenw10 Thermal Sensors
Intel Core* CPU on-die thermal sensor

stephenw10

You have SpeedShift enabled?

Be good to see more of that top output so we know what's generating that CPU load.

Antibiotic

@stephenw10

PID USERNAME    PRI NICE   SIZE    RES STATE    C   TIME    WCPU COMMAND
   11 root        187 ki31     0B    64K CPU2     2 122:26  58.07% [idle{idle: cpu2}]
   11 root        187 ki31     0B    64K CPU1     1 122:25  57.91% [idle{idle: cpu1}]
   11 root        187 ki31     0B    64K RUN      3 122:21  57.13% [idle{idle: cpu3}]
   11 root        187 ki31     0B    64K CPU0     0 124:38  56.37% [idle{idle: cpu0}]
69815 root         24    0   855M   469M select   3   0:57  17.04% /usr/local/bin/suricata --netmap -D -c /usr/local/etc/suricata/suricata_12484_igc1/suricata.yaml --pidfile /var/run/suric
69815 root         24    0   855M   469M select   3   0:58  16.84% /usr/local/bin/suricata --netmap -D -c /usr/local/etc/suricata/suricata_12484_igc1/suricata.yaml --pidfile /var/run/suric
69815 root         23    0   855M   469M select   3   0:50  15.64% /usr/local/bin/suricata --netmap -D -c /usr/local/etc/suricata/suricata_12484_igc1/suricata.yaml --pidfile /var/run/suric
69815 root         23    0   855M   469M select   2   1:05  14.86% /usr/local/bin/suricata --netmap -D -c /usr/local/etc/suricata/suricata_12484_igc1/suricata.yaml --pidfile /var/run/suric
69815 root         24    0   855M   469M select   2   1:05  14.11% /usr/local/bin/suricata --netmap -D -c /usr/local/etc/suricata/suricata_12484_igc1/suricata.yaml --pidfile /var/run/suric
   12 root        -60    -     0B   320K WAIT     3   0:22  10.66% [intr{swi1: netisr 1}]
69815 root         23    0   855M   469M select   0   1:24   9.82% /usr/local/bin/suricata --netmap -D -c /usr/local/etc/suricata/suricata_12484_igc1/suricata.yaml --pidfile /var/run/suric
69815 root         21    0   855M   469M select   0   1:32   7.52% /usr/local/bin/suricata --netmap -D -c /usr/local/etc/suricata/suricata_12484_igc1/suricata.yaml --pidfile /var/run/suric
56778 root         21    0   550M   390M bpf      1   0:43   7.41% /usr/local/bin/ntopng -d /var/db/ntopng -G /var/run/ntopng.pid -s -e -w 0 -W 3000 -i igc1 -i igc0 --dns-mode 0 --local-ne
56778 root         21    0   550M   390M bpf      0   0:52   7.24% /usr/local/bin/ntopng -d /var/db/ntopng -G /var/run/ntopng.pid -s -e -w 0 -W 3000 -i igc1 -i igc0 --dns-mode 0 --local-ne
    0 root        -60    -     0B  1808K -        0   0:39   6.15% [kernel{if_io_tqg_0}]
   12 root        -60    -     0B   320K WAIT     0   0:28   6.06% [intr{swi1: netisr 0}]
    0 root        -60    -     0B  1808K RUN      1   0:34   6.03% [kernel{if_io_tqg_1}]
    0 root        -60    -     0B  1808K -        3   0:39   5.93% [kernel{if_io_tqg_3}]
   12 root        -60    -     0B   320K WAIT     2   0:42   5.76% [intr{swi1: netisr 2}]
    0 root        -64    -     0B  1808K -        0   0:22   5.58% [kernel{dummynet}]
   12 root        -60    -     0B   320K WAIT     1   0:33   5.44% [intr{swi1: netisr 3}]
    0 root        -60    -     0B  1808K -        2   0:49   4.18% [kernel{if_io_tqg_2}]
69815 root         20    0   855M   469M select   0   1:23   2.37% /usr/local/bin/suricata --netmap -D -c /usr/local/etc/suricata/suricata_12484_igc1/suricata.yaml --pidfile /var/run/suric
69815 root         20    0   855M   469M uwait    3   0:45   0.24% /usr/local/bin/suricata --netmap -D -c /usr/local/etc/suricata/suricata_12484_igc1/suricata.yaml --pidfile /var/run/suric
56778 root         20    0   550M   390M nanslp   2   0:30   0.21% /usr/local/bin/ntopng -d /var/db/ntopng -G /var/run/ntopng.pid -s -e -w 0 -W 3000 -i igc1 -i igc0 --dns-mode 0 --local-ne
 6263 root         20    0  1411M   136M uwait    1   0:07   0.17% /usr/local/bin/crowdsec -c /usr/local/etc/crowdsec/config.yaml{crowdsec}
 6263 root         20    0  1411M   136M kqread   2   0:07   0.12% /usr/local/bin/crowdsec -c /usr/local/etc/crowdsec/config.yaml{crowdsec}
56778 root         20    0   550M   390M uwait    3   0:00   0.12% /usr/local/bin/ntopng -d /var/db/ntopng -G /var/run/ntopng.pid -s -e -w 0 -W 3000 -i igc1 -i igc0 --dns-mode 0 --local-ne
30798 unbound      20    0   355M   305M kqread   0   0:13   0.08% /usr/local/sbin/unbound -c /var/unbound/unbound.conf{unbound}
    2 root        -60    -     0B    64K WAIT     2   0:02   0.08% [clock{clock (2)}]
    8 root        -16    -     0B    16K -        3   0:02   0.08% [rand_harvestq]
    2 root        -60    -     0B    64K WAIT     3   0:01   0.07% [clock{clock (3)}]
56712 root         20    0    36M    12M kqread   1   0:05   0.07% redis-server: /usr/local/bin/redis-server 127.0.0.1:6379 (redis-server){redis-server}
    2 root        -60    -     0B    64K WAIT     0   0:02   0.07% [clock{clock (0)}]
37116 root         20    0    14M  4468K CPU1     1   0:01   0.07% top -HaSP
    2 root        -60    -     0B    64K WAIT     1   0:01   0.06% [clock{clock (1)}]
69815 root         20    0   855M   469M nanslp   1   0:49   0.06% /usr/local/bin/suricata --netmap -D -c /usr/local/etc/suricata/suricata_12484_igc1/suricata.yaml --pidfile /var/run/suric
56778 root         20    0   550M   390M uwait    0   0:00   0.05% /usr/local/bin/ntopng -d /var/db/ntopng -G /var/run/ntopng.pid -s -e -w 0 -W 3000 -i igc1 -i igc0 --dns-mode 0 --local-ne

Antibiotic

@stephenw10 Yes Speed Shift enabled

stephenw10

Ok so all Suricata load basically. If you disable it as a test without any other changes do you get full bandwidth?

Antibiotic

@stephenw10 Yes, exactly, if suricata disabled speed test show as should be about 95% of max capacity as set in traffic shaping limiters!

stephenw10

Hmm. Do you see the same in legacy and in-line mode?

Antibiotic

@stephenw10 Use in-line mode, don't use legacy mode. Do you want to test in legacy mode?

stephenw10

Yes, test legacy mode. See if there is any change.

Antibiotic

@stephenw10 In legacy mode looks like speed as should be

stephenw10

Hmm, so possibly some netmap issue. If you run sysctl dev.netmap.admode=1 it should prevent netmap running in emulated mode which is very slow. However that does mean it can only run in native mode so may break if that's not possible for some reason.

Antibiotic

@stephenw10 I will try to set in native mode, but also have net.bpf.zerocopy_enable=1 is it not a problem?

stephenw10

I wouldn't expect that to make any difference there if netmap is working. Why do you have that set?

Antibiotic

@stephenw10 During suricata installation at the end was this tip and I did)))