Watchguard Firebox XTM 8 Series

stephenw10

Right, that's what I mentioned earlier. The nanobsd_vga images have DMA enabled because of a specific device but many CF card slots do not have enough pins. Probably that's what's happening here.
Interrupt the boot process at the loader menu and do this:
http://doc.pfsense.org/index.php/Booting_Options#Disable_DMA_for_IDE_drives

Steve

wallabybob

My suspicion, based on the high LBA reported, is that your 4GB card is a bit short of providing 4GiB (1024 x 1024 x 1024) and the 4G image didn't quite fit. Some people have had to put a 2GB image on a "4GB" card/stick. Note the card is reported having 3815MB which would allow a LBA of up to around 7630000 which is a bit short of the reported LBAs.

If I recall correctly, the FreeBSD GEOM component goes looking for a GEOM signature on the apparent last sector or two of the disk.

Eams

I put a 2g nano_vga 64bit image on the same card and got the same LBA error.

Did the set hw.ata.atapi_dma=0 thing too which stopped the LBA errors, however got a different LBA error!

ad7: 3815MB <sandisk sdcfh-004g="" hdx="" 7.07="">at ata3-slave PIO4 SATA 1.5Gb/s
ad7: FAILURE - READ status=51 <ready,dsc,error>error=10 <nid_not_found>LBA=7813117
ad7: FAILURE - READ status=51 <ready,dsc,error>error=10 <nid_not_found>LBA=7813119
ad7: FAILURE - READ status=51 <ready,dsc,error>error=10 <nid_not_found>LBA=7813103
ad7: FAILURE - READ status=51 <ready,dsc,error>error=10 <nid_not_found>LBA=7813116
ad7: FAILURE - READ status=51 <ready,dsc,error>error=10 <nid_not_found>LBA=7813119
ad7: FAILURE - READ status=51 <ready,dsc,error>error=10 <nid_not_found>LBA=7813119
SMP: AP CPU #2 Launched!
SMP: AP CPU #1 Launched!
SMP: AP CPU #3 Launched!
ugen0.u1g:ue gn <e2i.nn11t.:e 1l:<="">I <naittne ltue="">s lb>au ts a0tus
ubsubsu2s
u1h
ub0: <intel 1="" 9="" uhci="" root="" hub,="" class="" 0,="" rev="" 1.00="" 1.00,="" addr="">on usbus0
uhub1: <intel 1="" 9="" ehci="" root="" hub,="" class="" 0,="" rev="" 2.00="" 1.00,="" addr="">on usbus2
uhub2: <intel 1="" 9="" uhci="" root="" hub,="" class="" 0,="" rev="" 1.00="" 1.00,="" addr="">on usbus1
ad7: FAILURE - READ status=51 <ready,dsc,error>error=10 <nid_not_found>LBA=7813119
Root mount waiting for: usbus2 usbus1 usbus0
uhub2: 2 ports with 2 removable, self powered
uhub0: 2 ports with 2 removable, self powered
Root mount waiting for: usbus2
uhub1: 4 ports with 4 removable, self powered
Trying to mount root from ufs:/dev/ufs/pfsense0
ad7: FAILURE - SETFEATURES 0x85 status=51 <ready,dsc,error>error=4 <aborted>ugen0.2: <chicony>at usbus0
ukbd0: <chicony 0="" 2="" usb="" keyboard,="" class="" 0,="" rev="" 2.00="" 1.57,="" addr="">on usbus0
kbd2 at ukbd0
pflog0: promiscuous mode enabled
ad7: FAILURE - READ status=51 <ready,dsc,error>error=10 <nid_not_found>LBA=7813119
ad7: FAILURE - READ status=51 <ready,dsc,error>error=10 <nid_not_found>LBA=7813119
ad7: FAILURE - READ status=51 <ready,dsc,error>error=10 <nid_not_found>LBA=7813119
ad7: FAILURE - READ status=51 <ready,dsc,error>error=10 <nid_not_found>LBA=7813119
ad7: FAILURE - READ status=51 <ready,dsc,error>error=10 <nid_not_found>LBA=7813119
ad7: FAILURE - READ status=51 <ready,dsc,error>error=10 <nid_not_found>LBA=7813119
ad7: FAILURE - READ status=51 <ready,dsc,error>error=10 <nid_not_found>LBA=7813119
ad7: FAILURE - READ status=51 <ready,dsc,error>error=10 <nid_not_found>LBA=7813119
ad7: FAILURE - READ status=51 <ready,dsc,error>error=10 <nid_not_found>LBA=7813119
ad7: FAILURE - READ status=51 <ready,dsc,error>error=10 <nid_not_found>LBA=7813119

Burning 2g nano_vga 32bit gives the same error on the same card (4gig SanDisk Ultra)

Booting up on the no name cf card with the same 32bit 2g nano_vga image gives no errors - no ser hw.ata.ata_dma=0 performed - wierd;

ad7: 3639MB <cf card="" ver5.04="">at ata3-slave UDMA33 SATA 1.5Gb/s
SMP: AP CPU #2 Launched!
SMP: AP CPU #1 Launched!
SMP: AP CPU #3 Launched!
ugen0u.1g:e n<2I.n1t:e l<>I natte l>u saubtu guss0beuns1
2.1
: <intel>at usbus1
uhub0: <intel 1="" 9="" uhci="" root="" hub,="" class="" 0,="" rev="" 1.00="" 1.00,="" addr="">on usbus0
uhub1: <intel 1="" 9="" uhci="" root="" hub,="" class="" 0,="" rev="" 1.00="" 1.00,="" addr="">on usbus1
uhub2: <intel 1="" 9="" ehci="" root="" hub,="" class="" 0,="" rev="" 2.00="" 1.00,="" addr="">on usbus2
Root mount waiting for: usbus2 usbus1 usbus0
uhub1: 2 ports with 2 removable, self powered
uhub0: 2 ports with 2 removable, self powered
Root mount waiting for: usbus2
uhub2: 4 ports with 4 removable, self powered
Trying to mount root from ufs:/dev/ufs/pfsense0
ugen0.2: <chicony>at usbus0
ukbd0: <chicony 0="" 2="" usb="" keyboard,="" class="" 0,="" rev="" 2.00="" 1.57,="" addr="">on usbus0
kbd2 at ukbd0
pflog0: promiscuous mode enabled

How very bizarre.

Eamon</chicony></chicony></intel></intel></intel></intel></cf></nid_not_found></ready,dsc,error></nid_not_found></ready,dsc,error></nid_not_found></ready,dsc,error></nid_not_found></ready,dsc,error></nid_not_found></ready,dsc,error></nid_not_found></ready,dsc,error></nid_not_found></ready,dsc,error></nid_not_found></ready,dsc,error></nid_not_found></ready,dsc,error></nid_not_found></ready,dsc,error></chicony></chicony></aborted></ready,dsc,error></nid_not_found></ready,dsc,error></intel></intel></intel></naittne></e2i.nn11t.:e></nid_not_found></ready,dsc,error></nid_not_found></ready,dsc,error></nid_not_found></ready,dsc,error></nid_not_found></ready,dsc,error></nid_not_found></ready,dsc,error></nid_not_found></ready,dsc,error></sandisk>

stephenw10

The 'nid not found' error is common and nothing to worry about:
http://doc.pfsense.org/index.php/DMA_and_LBA_Errors

I would guess that your no-name card is not DMA capable so didn't cause the problem.

Did it boot successfully then?

Steve

Eams

Damn I bought the exact same cf card that's in that link! I guess that's that error sorted then.

Yes it did boot, even with the LBA errors, looks like it was a combination of both errors mentioned by yourself and wallabybob.
Its pretty nippy to say the least ;)
I gotta figure out how to set it up now. At least 10x GbE ports gives me plenty to play with haha!

I've contacted Lanner to see if I can get the BIOS for the 8750 this is based on, that would help even further.

Eamon

fmertz

@Eams:

The LCD seems to be the same as previous models as you say so should be ok.

There is an arm/disarm led on the front, it hasn't lit up yet.

There is some useful info there about the FW-8750 of which this board seems to be from:

Platform
Chipset: Intel Q35 + ICH9D0

Eamon

The LCD code assumes parallel port, so, at a minimum, the sdeclcd driver part of the lcdproc package should run. Might even work, too.

For the LEDs, the driver code supports the various models based on standard PCI detection of the ICH. We definitely need to add an entry for this ICH9 in the driver code. Once you guys get around to it, can you confirm this is, in fact, an ICH9D0, identified by Vendor x8086, device x2914 (the numbers are listed on page 12 of the "Intel I/O Controller Hub 9 (ICH9) Family Specification Update")?

Generally, the LEDs can be wired off of the GPIO device part of this ICH (like in the older models), but, more likely, they are wired off of the SuperIO chip (like the XTM 5). A further screen shot seems to list an ITE8718. This is where the research comes in to identify which line these LEDs are wired off of. I'll be happy to code this in when it is discovered.

stephenw10

Commence experimental probing! ;D

Since you don't have the Watchguard OS we can't look for clues in it's boot messages.

Not using a Winbond sio chip, interesting.

You could extract the bios code with flashrom and look at it for hidden menus.

Steve

Edit: Looks to be supported by superiotool as well.

Eams

fmertz:
Ok, fired up lcdproc, but nothing seems to happen :(

The boot up screen shows 'Starting package LCDproc…done.'

Under Status: Services it shows as Stopped. Clicking to start it doesn't change it's status.

ICH9 Chipset - think you were right, experimental probe..:

$ pciconf -lc
hostb0@pci0:0:0:0: class=0x060000 card=0x29b08086 chip=0x29b08086 rev=0x02 hdr=0x00
cap 09[e0] = vendor (length 11) Intel cap 11 version 1
pcib1@pci0:0:1:0: class=0x060400 card=0x29b18086 chip=0x29b18086 rev=0x02 hdr=0x01
cap 0d[88] = PCI Bridge card=0x29b18086
cap 01[80] = powerspec 3 supports D0 D3 current D0
cap 05[90] = MSI supports 1 message
cap 10[a0] = PCI-Express 1 root port max data 128(128) link x4(x16)
vgapci0@pci0:0:2:0: class=0x030000 card=0x29b28086 chip=0x29b28086 rev=0x02 hdr=0x00
cap 05[90] = MSI supports 1 message
cap 01[d0] = powerspec 2 supports D0 D3 current D0
em4@pci0:0:25:0: class=0x020000 card=0x00008086 chip=0x10bd8086 rev=0x02 hdr=0x00
cap 01[c8] = powerspec 2 supports D0 D3 current D0
cap 05[d0] = MSI supports 1 message, 64 bit enabled with 1 message
cap 13[e0] = PCI Advanced Features: FLR TP
pcib9@pci0:0:28:0: class=0x060400 card=0x29408086 chip=0x29408086 rev=0x02 hdr=0x01
cap 10[40] = PCI-Express 1 root port max data 128(128) link x1(x1)
cap 05[80] = MSI supports 1 message
cap 0d[90] = PCI Bridge card=0x29408086
cap 01[a0] = powerspec 2 supports D0 D3 current D0
pcib10@pci0:0:28:1: class=0x060400 card=0x29428086 chip=0x29428086 rev=0x02 hdr=0x01
cap 10[40] = PCI-Express 1 root port max data 128(128) link x1(x1)
cap 05[80] = MSI supports 1 message
cap 0d[90] = PCI Bridge card=0x29428086
cap 01[a0] = powerspec 2 supports D0 D3 current D0
pcib11@pci0:0:28:2: class=0x060400 card=0x29448086 chip=0x29448086 rev=0x02 hdr=0x01
cap 10[40] = PCI-Express 1 root port max data 128(128) link x1(x1)
cap 05[80] = MSI supports 1 message
cap 0d[90] = PCI Bridge card=0x29448086
cap 01[a0] = powerspec 2 supports D0 D3 current D0
pcib12@pci0:0:28:3: class=0x060400 card=0x29468086 chip=0x29468086 rev=0x02 hdr=0x01
cap 10[40] = PCI-Express 1 root port max data 128(128) link x1(x1)
cap 05[80] = MSI supports 1 message
cap 0d[90] = PCI Bridge card=0x29468086
cap 01[a0] = powerspec 2 supports D0 D3 current D0
pcib13@pci0:0:28:4: class=0x060400 card=0x29488086 chip=0x29488086 rev=0x02 hdr=0x01
cap 10[40] = PCI-Express 1 root port max data 128(128) link x1(x1)
cap 05[80] = MSI supports 1 message
cap 0d[90] = PCI Bridge card=0x29488086
cap 01[a0] = powerspec 2 supports D0 D3 current D0
uhci0@pci0:0:29:0: class=0x0c0300 card=0x29348086 chip=0x29348086 rev=0x02 hdr=0x00
cap 13[50] = PCI Advanced Features: FLR TP
uhci1@pci0:0:29:1: class=0x0c0300 card=0x29358086 chip=0x29358086 rev=0x02 hdr=0x00
cap 13[50] = PCI Advanced Features: FLR TP
ehci0@pci0:0:29:7: class=0x0c0320 card=0x293a8086 chip=0x293a8086 rev=0x02 hdr=0x00
cap 01[50] = powerspec 2 supports D0 D3 current D0
cap 0a[58] = EHCI Debug Port at offset 0xa0 in map 0x14
cap 13[98] = PCI Advanced Features: FLR TP
pcib14@pci0:0:30:0: class=0x060401 card=0x244e8086 chip=0x244e8086 rev=0x92 hdr=0x01
cap 0d[50] = PCI Bridge card=0x244e8086
isab0@pci0:0:31:0: class=0x060100 card=0x29148086 chip=0x29148086 rev=0x02 hdr=0x00
cap 09[e0] = vendor (length 12) Intel cap 1 version 0
features: SATA RAID-5, 4 PCI-e x1 slots
atapci0@pci0:0:31:2: class=0x01018f card=0x29208086 chip=0x29208086 rev=0x02 hdr=0x00
cap 01[70] = powerspec 3 supports D0 D3 current D0
cap 13[b0] = PCI Advanced Features: FLR TP
none0@pci0:0:31:3: class=0x0c0500 card=0x29308086 chip=0x29308086 rev=0x02 hdr=0x00
atapci1@pci0:0:31:5: class=0x010185 card=0x29268086 chip=0x29268086 rev=0x02 hdr=0x00
cap 01[70] = powerspec 3 supports D0 D3 current D0
cap 13[b0] = PCI Advanced Features: FLR TP
pcib2@pci0:7:0:0: class=0x060400 card=0x862410b5 chip=0x862410b5 rev=0xbb hdr=0x01
cap 01[40] = powerspec 3 supports D0 D3 current D0
cap 05[48] = MSI supports 4 messages, 64 bit, vector masks
cap 10[68] = PCI-Express 2 upstream port max data 128(2048) link x4(x4)
cap 0d[a4] = PCI Bridge card=0x862410b5
pcib3@pci0:8:0:0: class=0x060400 card=0x862410b5 chip=0x862410b5 rev=0xbb hdr=0x01
cap 01[40] = powerspec 3 supports D0 D3 current D0
cap 05[48] = MSI supports 4 messages, 64 bit, vector masks
cap 10[68] = PCI-Express 2 downstream port max data 128(2048) link x4(x4)
cap 0d[a4] = PCI Bridge card=0x862410b5
pcib4@pci0:8:1:0: class=0x060400 card=0x862410b5 chip=0x862410b5 rev=0xbb hdr=0x01
cap 01[40] = powerspec 3 supports D0 D3 current D0
cap 05[48] = MSI supports 4 messages, 64 bit, vector masks
cap 10[68] = PCI-Express 2 downstream port max data 128(2048) link x1(x4)
cap 0d[a4] = PCI Bridge card=0x862410b5
pcib5@pci0:8:4:0: class=0x060400 card=0x862410b5 chip=0x862410b5 rev=0xbb hdr=0x01
cap 01[40] = powerspec 3 supports D0 D3 current D0
cap 05[48] = MSI supports 4 messages, 64 bit, vector masks
cap 10[68] = PCI-Express 2 downstream port max data 128(2048) link x0(x8)
cap 0d[a4] = PCI Bridge card=0x862410b5
pcib6@pci0:8:6:0: class=0x060400 card=0x862410b5 chip=0x862410b5 rev=0xbb hdr=0x01
cap 01[40] = powerspec 3 supports D0 D3 current D0
cap 05[48] = MSI supports 4 messages, 64 bit, vector masks
cap 10[68] = PCI-Express 2 downstream port max data 128(2048) link x1(x4)
cap 0d[a4] = PCI Bridge card=0x862410b5
pcib7@pci0:8:8:0: class=0x060400 card=0x862410b5 chip=0x862410b5 rev=0xbb hdr=0x01
cap 01[40] = powerspec 3 supports D0 D3 current D0
cap 05[48] = MSI supports 4 messages, 64 bit, vector masks
cap 10[68] = PCI-Express 2 downstream port max data 128(2048) link x1(x4)
cap 0d[a4] = PCI Bridge card=0x862410b5
pcib8@pci0:8:9:0: class=0x060400 card=0x862410b5 chip=0x862410b5 rev=0xbb hdr=0x01
cap 01[40] = powerspec 3 supports D0 D3 current D0
cap 05[48] = MSI supports 4 messages, 64 bit, vector masks
cap 10[68] = PCI-Express 2 downstream port max data 128(2048) link x1(x4)
cap 0d[a4] = PCI Bridge card=0x862410b5
none1@pci0:14:0:0: class=0x100000 card=0x0001177d chip=0x0010177d rev=0x01 hdr=0x00
cap 01[40] = powerspec 3 supports D0 D3 current D0
cap 05[50] = MSI supports 1 message, 64 bit
cap 10[70] = PCI-Express 1 endpoint max data 128(256) link x4(x4)
em0@pci0:13:0:0: class=0x020000 card=0x00008086 chip=0x10d38086 rev=0x00 hdr=0x00
cap 01[c8] = powerspec 2 supports D0 D3 current D0
cap 05[d0] = MSI supports 1 message, 64 bit
cap 10[e0] = PCI-Express 1 endpoint max data 128(256) link x1(x1)
cap 11[a0] = MSI-X supports 3 messages in map 0x1c enabled
em1@pci0:11:0:0: class=0x020000 card=0x00008086 chip=0x10d38086 rev=0x00 hdr=0x00
cap 01[c8] = powerspec 2 supports D0 D3 current D0
cap 05[d0] = MSI supports 1 message, 64 bit
cap 10[e0] = PCI-Express 1 endpoint max data 128(256) link x1(x1)
cap 11[a0] = MSI-X supports 3 messages in map 0x1c enabled
em2@pci0:10:0:0: class=0x020000 card=0x00008086 chip=0x10d38086 rev=0x00 hdr=0x00
cap 01[c8] = powerspec 2 supports D0 D3 current D0
cap 05[d0] = MSI supports 1 message, 64 bit
cap 10[e0] = PCI-Express 1 endpoint max data 128(256) link x1(x1)
cap 11[a0] = MSI-X supports 3 messages in map 0x1c enabled
em3@pci0:9:0:0: class=0x020000 card=0x00008086 chip=0x10d38086 rev=0x00 hdr=0x00
cap 01[c8] = powerspec 2 supports D0 D3 current D0
cap 05[d0] = MSI supports 1 message, 64 bit
cap 10[e0] = PCI-Express 1 endpoint max data 128(256) link x1(x1)
cap 11[a0] = MSI-X supports 3 messages in map 0x1c enabled
em5@pci0:6:0:0: class=0x020000 card=0x00008086 chip=0x109a8086 rev=0x00 hdr=0x00
cap 01[c8] = powerspec 2 supports D0 D3 current D0
cap 05[d0] = MSI supports 1 message, 64 bit enabled with 1 message
cap 10[e0] = PCI-Express 1 endpoint max data 128(256) link x1(x1)
em6@pci0:5:0:0: class=0x020000 card=0x00008086 chip=0x109a8086 rev=0x00 hdr=0x00
cap 01[c8] = powerspec 2 supports D0 D3 current D0
cap 05[d0] = MSI supports 1 message, 64 bit enabled with 1 message
cap 10[e0] = PCI-Express 1 endpoint max data 128(256) link x1(x1)
em7@pci0:4:0:0: class=0x020000 card=0x00008086 chip=0x109a8086 rev=0x00 hdr=0x00
cap 01[c8] = powerspec 2 supports D0 D3 current D0
cap 05[d0] = MSI supports 1 message, 64 bit enabled with 1 message
cap 10[e0] = PCI-Express 1 endpoint max data 128(256) link x1(x1)
em8@pci0:3:0:0: class=0x020000 card=0x00008086 chip=0x109a8086 rev=0x00 hdr=0x00
cap 01[c8] = powerspec 2 supports D0 D3 current D0
cap 05[d0] = MSI supports 1 message, 64 bit enabled with 1 message
cap 10[e0] = PCI-Express 1 endpoint max data 128(256) link x1(x1)
em9@pci0:2:0:0: class=0x020000 card=0x00008086 chip=0x109a8086 rev=0x00 hdr=0x00
cap 01[c8] = powerspec 2 supports D0 D3 current D0
cap 05[d0] = MSI supports 1 message, 64 bit enabled with 1 message
cap 10[e0] = PCI-Express 1 endpoint max data 128(256) link x1(x1)

Stephen:
I managed to upload superiotool to /tmp/ but don't know how to run it :(

Ditto flashrom!

Eamon

Eams

Another experimental probe..

$ sysctl hw
hw.machine: i386
hw.model: Intel(R) Core(TM)2 Quad CPU Q9400 @ 2.66GHz
hw.ncpu: 4
hw.byteorder: 1234
hw.physmem: 2120441856
hw.usermem: 2066382848
hw.pagesize: 4096
hw.floatingpoint: 1
hw.machine_arch: i386
hw.realmem: 2137784320
hw.amr.force_sg32: 0
hw.an.an_cache_iponly: 1
hw.an.an_cache_mcastonly: 0
hw.an.an_cache_mode: dbm
hw.an.an_dump: off
hw.ata.setmax: 0
hw.ata.wc: 1
hw.ata.atapi_dma: 1
hw.ata.ata_dma_check_80pin: 1
hw.ata.ata_dma: 1
hw.ath.bstuck: 4
hw.ath.txbuf: 200
hw.ath.rxbuf: 40
hw.ath.resetcal: 1200
hw.ath.shortcal: 100
hw.ath.longcal: 30
hw.ath.hal.swba_backoff: 0
hw.ath.hal.sw_brt: 10
hw.ath.hal.dma_brt: 2
hw.bce.msi_enable: 1
hw.bce.tso_enable: 1
hw.bge.allow_asf: 0
hw.bt848.slow_msp_audio: -1
hw.bt848.format: -1
hw.bt848.reverse_mute: -1
hw.bt848.tuner: -1
hw.bt848.card: -1
hw.bwn.wme: 1
hw.bwn.usedma: 1
hw.bwn.hwpctl: 0
hw.bwn.bluetooth: 1
hw.bwn.bfp: 0
hw.cardbus.cis_debug: 0
hw.cardbus.debug: 0
hw.cxgb.snd_queue_len: 128
hw.cxgb.use_16k_clusters: -1
hw.cxgb.force_fw_update: 0
hw.cxgb.multiq: 1
hw.cxgb.ofld_disable: 0
hw.cxgb.msi_allowed: 2
hw.cxgb.tx_reclaim_threshold: 32
hw.cxgb.tx_coalesce_enable_stop: 256
hw.cxgb.tx_coalesce_enable_start: 512
hw.cxgb.tx_coalesce_force: 0
hw.cxgb.txq_mr_size: 1024
hw.em.eee_setting: 0
hw.em.rx_process_limit: 100
hw.em.enable_msix: 1
hw.em.sbp: 0
hw.em.smart_pwr_down: 0
hw.em.txd: 1024
hw.em.rxd: 1024
hw.em.rx_abs_int_delay: 66
hw.em.tx_abs_int_delay: 66
hw.em.rx_int_delay: 0
hw.em.tx_int_delay: 66
hw.igb.rx_process_limit: 100
hw.igb.num_queues: 0
hw.igb.header_split: 0
hw.igb.max_interrupt_rate: 8000
hw.igb.enable_msix: 1
hw.igb.enable_aim: 1
hw.igb.txd: 1024
hw.igb.rxd: 1024
hw.firewire.hold_count: 0
hw.firewire.try_bmr: 1
hw.firewire.fwmem.speed: 2
hw.firewire.fwmem.eui64_lo: 0
hw.firewire.fwmem.eui64_hi: 0
hw.firewire.phydma_enable: 1
hw.firewire.nocyclemaster: 0
hw.firewire.fwe.rx_queue_len: 128
hw.firewire.fwe.tx_speed: 2
hw.firewire.fwe.stream_ch: 1
hw.firewire.sbp.tags: 0
hw.firewire.sbp.use_doorbell: 0
hw.firewire.sbp.scan_delay: 500
hw.firewire.sbp.login_delay: 1000
hw.firewire.sbp.exclusive_login: 1
hw.firewire.sbp.max_speed: -1
hw.firewire.sbp.auto_login: 1
hw.hifn.maxbatch: 1
hw.hifn.debug: 0
hw.malo.txbuf: 256
hw.malo.rxquota: 256
hw.malo.rxbuf: 256
hw.malo.txcoalesce: 8
hw.malo.pci.msi_disable: 0
hw.mfi.max_cmds: 128
hw.mfi.event_class: 0
hw.mfi.event_locale: 65535
hw.mwl.rxdmalow: 3
hw.mwl.rxquota: 640
hw.mwl.txcoalesce: 8
hw.mwl.txbuf: 256
hw.mwl.rxbuf: 640
hw.mwl.rxdesc: 256
hw.pccard.cis_debug: 0
hw.pccard.debug: 0
hw.cbb.debug: 0
hw.cbb.start_32_io: 4096
hw.cbb.start_16_io: 256
hw.cbb.start_memory: 2281701376
hw.pcic.pd6722_vsense: 1
hw.pcic.intr_mask: 57016
hw.pci.usb_early_takeover: 1
hw.pci.honor_msi_blacklist: 1
hw.pci.enable_msix: 1
hw.pci.enable_msi: 1
hw.pci.do_power_resume: 1
hw.pci.do_power_nodriver: 0
hw.pci.enable_io_modes: 1
hw.pci.default_vgapci_unit: -1
hw.pci.host_mem_start: 2147483648
hw.pci.mcfg: 1
hw.pci.irq_override_mask: 57080
hw.safe.rngmaxalarm: 8
hw.safe.rngbufsize: 16
hw.safe.rnginterval: 1
hw.syscons.kbd_debug: 1
hw.syscons.kbd_reboot: 0
hw.syscons.bell: 1
hw.syscons.saver.keybonly: 1
hw.syscons.sc_no_suspend_vtswitch: 0
hw.usb.no_boot_wait: 0
hw.usb.debug: 0
hw.usb.usb_lang_mask: 255
hw.usb.usb_lang_id: 9
hw.usb.template: 0
hw.usb.power_timeout: 30
hw.usb.uath.regdomain: 0
hw.usb.uath.countrycode: 0
hw.usb.urtw.preamble_mode: 2
hw.usb.urtw.debug: 0
hw.usb.ucom.cons_baud: 9600
hw.usb.ucom.cons_unit: -1
hw.wi.debug: 0
hw.wi.txerate: 0
hw.intr_storm_threshold: 1000
hw.pagesizes: 4096 0
hw.availpages: 517686
hw.bus.devctl_queue: 1000
hw.bus.devctl_disable: 0
hw.kbd.keymap_restrict_change: 0
hw.nve_pollinterval: 0
hw.busdma.total_bpages: 128
hw.busdma.zone0.total_bpages: 128
hw.busdma.zone0.free_bpages: 128
hw.busdma.zone0.reserved_bpages: 0
hw.busdma.zone0.active_bpages: 0
hw.busdma.zone0.total_bounced: 0
hw.busdma.zone0.total_deferred: 0
hw.busdma.zone0.lowaddr: 0xffffffff
hw.busdma.zone0.alignment: 4096
hw.clockrate: 2660
hw.via_feature_xcrypt: 0
hw.via_feature_rng: 0
hw.instruction_sse: 1
hw.apic.enable_extint: 0
hw.mca.erratum383: 0
hw.mca.amd10h_L1TP: 1
hw.mca.enabled: 1
hw.mca.count: 0
hw.mca.interval: 3600
hw.mca.force_scan: 0
hw.acpi.supported_sleep_state: S1 S4 S5
hw.acpi.power_button_state: S5
hw.acpi.sleep_button_state: S1
hw.acpi.lid_switch_state: NONE
hw.acpi.standby_state: S1
hw.acpi.suspend_state: NONE
hw.acpi.sleep_delay: 1
hw.acpi.s4bios: 0
hw.acpi.verbose: 0
hw.acpi.disable_on_reboot: 0
hw.acpi.handle_reboot: 0
hw.acpi.reset_video: 0
hw.acpi.cpu.cx_lowest: C1

Eamon

Eams

Another..

$ sysctl dev.cpu
dev.cpu.0.%desc: ACPI CPU
dev.cpu.0.%driver: cpu
dev.cpu.0.%location: handle=_PR_.P001
dev.cpu.0.%pnpinfo: _HID=none UID=0
dev.cpu.0.%parent: acpi0
dev.cpu.0.cx_supported: C1/0
dev.cpu.0.cx_lowest: C1
dev.cpu.0.cx_usage: 100.00% last 5000us
dev.cpu.0.freq: 330
dev.cpu.0.freq_levels: 2646/-1 2315/-1 1984/-1 1653/-1 1323/-1 992/-1 661/-1 330/-1
dev.cpu.1.%desc: ACPI CPU
dev.cpu.1.%driver: cpu
dev.cpu.1.%location: handle=_PR.P002
dev.cpu.1.%pnpinfo: _HID=none UID=0
dev.cpu.1.%parent: acpi0
dev.cpu.1.cx_supported: C1/0
dev.cpu.1.cx_lowest: C1
dev.cpu.1.cx_usage: 100.00% last 5000us
dev.cpu.2.%desc: ACPI CPU
dev.cpu.2.%driver: cpu
dev.cpu.2.%location: handle=_PR.P003
dev.cpu.2.%pnpinfo: _HID=none UID=0
dev.cpu.2.%parent: acpi0
dev.cpu.2.cx_supported: C1/0
dev.cpu.2.cx_lowest: C1
dev.cpu.2.cx_usage: 100.00% last 5000us
dev.cpu.3.%desc: ACPI CPU
dev.cpu.3.%driver: cpu
dev.cpu.3.%location: handle=_PR.P004
dev.cpu.3.%pnpinfo: _HID=none _UID=0
dev.cpu.3.%parent: acpi0
dev.cpu.3.cx_supported: C1/0
dev.cpu.3.cx_lowest: C1
dev.cpu.3.cx_usage: 100.00% last 5000us

Eamon

stephenw10

To use either of those tools you have to install the FreeBSD package properly, so:

As you are running NanoBD first remount the filesystem read-write

[2.0.3-RELEASE][root@pfsense.fire.box]/root(1): /etc/rc.conf_mount_rw

Then add the package. You have to specify the complete path beacsue FreeBSD 8.1 is now quite old

[2.0.3-RELEASE][root@pfsense.fire.box]/root(2): pkg_add -r ftp://ftp-archive.freebsd.org/pub/FreeBSD-Archive/ports/i386/packages-8.1-release/Latest/superiotool.tbz
Fetching ftp://ftp-archive.freebsd.org/pub/FreeBSD-Archive/ports/i386/packages-8.1-release/Latest/superiotool.tbz... Done.

same for flashrom

[2.0.3-RELEASE][root@pfsense.fire.box]/root(3): pkg_add -r ftp://ftp-archive.freebsd.org/pub/FreeBSD-Archive/ports/i386/packages-8.1-release/Latest/flashrom.tbz
Fetching ftp://ftp-archive.freebsd.org/pub/FreeBSD-Archive/ports/i386/packages-8.1-release/Latest/flashrom.tbz... Done.
Fetching ftp://ftp-archive.freebsd.org/pub/FreeBSD-Archive/ports/i386/packages-8.1-release/All/libpci-3.1.7_1.tbz... Done.

Then remount the filesystem read-only again

[2.0.3-RELEASE][root@pfsense.fire.box]/root(4): /etc/rc.conf_mount_ro

Finally issue a rehash to re-index the new files so FreeBSD knows where to find them

[2.0.3-RELEASE][root@pfsense.fire.box]/root(5): rehash

Now you run the tools. :)

After you install the lcdproc-dev package via the pfSense GUI you have to configure the various parameters before it will run and then start the service manually the first time in Status: Services:

Steve

fmertz

@Eams:

isab0@pci0:0:31:0: class=0x060100 card=0x29148086 chip=0x29148086 rev=0x02 hdr=0x00

Yep, confirmed ICH9D0. Dom 0, bus 0, device 31, function 0 is the L(ow)P(in)C(ount) device. We can use it to identify the exact ICH model number.

Eams

I had lcdproc loaded - removed and installed lcdproc-dev - selected WatchGuard Firebox with SDEC (x86only) - see attached pics.

Looks like powerd is doing it's job running the cpu at 330Mhz - fans however haven't slowed down any though :(

Superiotool probe..:
$ superiotool -d
superiotool r
Found ITE IT8718F (id=0x8718, rev=0x4) at 0x2e
Register dump:
idx 20 21 22 23 24 2b
val 87 18 04 10 00 00
def 87 18 01 00 00 00
LDN 0x00 (Floppy)
idx 30 60 61 70 74 f0 f1
val 00 00 00 00 04 00 00
def 00 03 f0 06 02 00 00
LDN 0x01 (COM1)
idx 30 60 61 70 f0 f1 f2 f3
val 00 03 f8 04 00 50 00 7f
def 00 03 f8 04 00 50 00 7f
LDN 0x02 (COM2)
idx 30 60 61 70 f0 f1 f2 f3
val 01 02 f8 03 00 50 00 7f
def 00 02 f8 03 00 50 00 7f
LDN 0x03 (Parallel port)
idx 30 60 61 62 63 70 74 f0
val 01 03 78 00 00 07 04 08
def 00 03 78 07 78 07 03 03
LDN 0x04 (Environment controller)
idx 30 60 61 62 63 70 f0 f1 f2 f3 f4 f5 f6
val 01 0a 10 0a 00 00 80 00 00 00 a0 00 ff
def 00 02 90 02 30 09 00 00 00 00 00 NA NA
LDN 0x05 (Keyboard)
idx 30 60 61 62 63 70 71 f0
val 01 00 60 00 64 01 02 00
def 01 00 60 00 64 01 02 00
LDN 0x06 (Mouse)
idx 30 70 71 f0
val 01 0c 02 00
def 00 0c 02 00
LDN 0x07 (GPIO)
idx 25 26 27 28 29 2a 2c 60 61 62 63 64 65 70 71 72 73 74 b0 b1 b2 b3 b4 b5 b8 b9 ba bb bc bd c0 c1 c2 c3 c4 c5 c8 c9 ca cb cc e0 e1 e2 e3 e4 e5 e6 e7 f0 f1 f2 f3 f4 f5 f6 f7 f8 f9 fa fb fc fd fe ff
val 41 d3 00 00 00 20 1f 00 00 0a 20 0a 30 00 00 00 00 00 00 00 00 00 00 00 40 00 00 00 00 00 40 d3 00 40 00 00 40 d0 00 40 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 bc 00 00 00
def 01 00 00 40 00 00 00 00 00 00 00 00 00 00 00 20 38 00 00 00 00 00 00 00 00 00 00 00 00 00 01 00 00 40 00 00 01 00 00 40 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 NA 00 00 00
LDN 0x0a (Consumer IR)
idx 30 60 61 70 f0
val 00 00 00 00 06
def 00 03 10 0b 00

Hope that is of some use ;D

Haven't managed to get flashrom to run ???

Eamon

IMG_20130517_004538.jpg_thumb

IMG_20130517_005003.jpg_thumb

fmertz

@Eams:

Selected WatchGuard Firebox with SDEC (x86only) - see attached pics.

That was an easy win. Good to see, though. Have you tried the buttons? Best guess, they sort of work, but are not mapped correctly…

stephenw10

What happens when you try to run flashrom?

Steve

Eams

fmertz:
I've tried the buttons, but with the display being so faint, it's hard to see properly. I'll try and have a further play tonight.

Steve:
With flashrom I'm getting the error:
/usr/local/bin/flashrom: Exec format error. Binary file not executable.

Eamon

stephenw10

Ah, that's interesting. Looking back through the boot logs you posted earlier it looks like you were running 64bit, is that still the case?
That explains the wrong binary error.

If that is the case:
Remount the filesystem and remove flashrom with

pkg_delete flashrom

Then add the correct version

pkg_add -r ftp://ftp-archive.freebsd.org/pub/FreeBSD-Archive/ports/amd64/packages-8.1-release/Latest/flashrom.tbz

See how that goes, I'm not entirely sure what will happen. You may need to manually remove libpci-3.1.7_1 it may just be overwritten. :-\

Interesting that superiotool worked fine and that the sdeclcd driver worked.

Steve

Eams

Removed flashrom and libpci-3.1.7_1 but still got the same /usr/local/bin/flashrom: Exec format error. Binary file not executable error.

Just checked and I'm running the nano_vga i386 build ::)

Removed both mentioned above and applied the i386 packages - flashrom now works :)

$ flashrom -V
flashrom v0.9.2-r1001 on FreeBSD 8.1-RELEASE-p13 (i386), built with libpci 3.1.7, GCC 4.2.1 20070719  [FreeBSD]
flashrom is free software, get the source code at http://www.flashrom.org

Initializing internal programmer
No coreboot table found.
dmidecode execution unsucessfull - continuing without DMI info
Found ITE Super I/O, id 8718
Found chipset "Intel ICH9DO", enabling flash write... 
0xfff80000/0xffb80000 FWH IDSEL: 0x0
0xfff00000/0xffb00000 FWH IDSEL: 0x0
0xffe80000/0xffa80000 FWH IDSEL: 0x1
0xffe00000/0xffa00000 FWH IDSEL: 0x1
0xffd80000/0xff980000 FWH IDSEL: 0x2
0xffd00000/0xff900000 FWH IDSEL: 0x2
0xffc80000/0xff880000 FWH IDSEL: 0x3
0xffc00000/0xff800000 FWH IDSEL: 0x3
0xff700000/0xff300000 FWH IDSEL: 0x4
0xff600000/0xff200000 FWH IDSEL: 0x5
0xff500000/0xff100000 FWH IDSEL: 0x6
0xff400000/0xff000000 FWH IDSEL: 0x7
0xfff80000/0xffb80000 FWH decode enabled
0xfff00000/0xffb00000 FWH decode enabled
0xffe80000/0xffa80000 FWH decode disabled
0xffe00000/0xffa00000 FWH decode disabled
0xffd80000/0xff980000 FWH decode disabled
0xffd00000/0xff900000 FWH decode disabled
0xffc80000/0xff880000 FWH decode disabled
0xffc00000/0xff800000 FWH decode disabled
0xff700000/0xff300000 FWH decode disabled
0xff600000/0xff200000 FWH decode disabled
0xff500000/0xff100000 FWH decode disabled
0xff400000/0xff000000 FWH decode disabled
Maximum FWH chip size: 0x100000 bytes
BIOS Lock Enable: disabled, BIOS Write Enable: enabled, BIOS_CNTL is 0x1

Root Complex Register Block address = 0xfed1c000
GCS = 0x464: BIOS Interface Lock-Down: disabled, BOOT BIOS Straps: 0x1 (SPI)
Top Swap : not enabled
SPIBAR = 0xfed1c000 + 0x3800
0x04: 0x6008 (HSFS)
FLOCKDN 0, FDV 1, FDOPSS 1, SCIP 0, BERASE 1, AEL 0, FCERR 0, FDONE 0
0x50: 0x0000ffff (FRAP)
BMWAG 0, BMRAG 0, BRWA 255, BRRA 255
0x54: 0x00000000 (FREG0)
0x58: 0x01020003 (FREG1)
0x5C: 0x00000fff (FREG2)
0x60: 0x00020001 (FREG3)
0x64: 0x00000fff (FREG4)
0x74: 0x00000000 (PR0)
0x78: 0x00000000 (PR1)
0x7C: 0x00000000 (PR2)
0x80: 0x00000000 (PR3)
0x84: 0x00000000 (PR4)
0x90: 0x00414004 (SSFS, SSFC)
0x94: 0x5006     (PREOP)
0x96: 0x463b     (OPTYPE)
0x98: 0x05d80302 (OPMENU)
0x9C: 0xc79f0190 (OPMENU+4)
0xA0: 0x00000000 (BBAR)
0xB0: 0x00004000 (FDOC)
Programming OPCODES... 
program_opcodes: preop=5006 optype=463b opmenu=05d80302c79f0190
done
SPI Read Configuration: prefetching disabled, caching enabled, OK.
This chipset supports the following protocols: FWH,SPI.
No IT87* serial flash segment enabled.
Calibrating delay loop... 1995M loops per second, 10 myus = 11 us, 100 myus = 102 us, 1000 myus = 1002 us, 10000 myus = 10006 us, OK.
Probing for AMD Am29F010A/B, 128 KB: skipped.
Probing for AMD Am29F002(N)BB, 256 KB: skipped.
Probing for AMD Am29F002(N)BT, 256 KB: skipped.
Probing for AMD Am29F016D, 2048 KB: skipped.
Probing for AMD Am29F040B, 512 KB: skipped.
Probing for AMD Am29F080B, 1024 KB: skipped.
Probing for AMD Am29LV040B, 512 KB: skipped.
Probing for AMD Am29LV081B, 1024 KB: skipped.
Probing for ASD AE49F2008, 256 KB: skipped.
Probing for Atmel AT25DF021, 256 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x2541
Probing for Atmel AT25DF041A, 512 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x2541
Probing for Atmel AT25DF081, 1024 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x2541
Probing for Atmel AT25DF161, 2048 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x2541
Probing for Atmel AT25DF321, 4096 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x2541
Probing for Atmel AT25DF321A, 4096 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x2541
Probing for Atmel AT25DF641, 8192 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x2541
Probing for Atmel AT25F512B, 64 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x2541
Probing for Atmel AT25FS010, 128 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x2541
Probing for Atmel AT25FS040, 512 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x2541
Probing for Atmel AT26DF041, 512 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x2541
Probing for Atmel AT26DF081A, 1024 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x2541
Probing for Atmel AT26DF161, 2048 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x2541
Probing for Atmel AT26DF161A, 2048 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x2541
Probing for Atmel AT26F004, 512 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x2541
Probing for Atmel AT29C512, 64 KB: skipped.
Probing for Atmel AT29C010A, 128 KB: skipped.
Probing for Atmel AT29C020, 256 KB: skipped.
Probing for Atmel AT29C040A, 512 KB: skipped.
Probing for Atmel AT45CS1282, 16896 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x2541
Probing for Atmel AT45DB011D, 128 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x2541
Probing for Atmel AT45DB021D, 256 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x2541
Probing for Atmel AT45DB041D, 512 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x2541
Probing for Atmel AT45DB081D, 1024 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x2541
Probing for Atmel AT45DB161D, 2048 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x2541
Probing for Atmel AT45DB321C, 4224 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x2541
Probing for Atmel AT45DB321D, 4096 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x2541
Probing for Atmel AT45DB642D, 8192 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x2541
Probing for Atmel AT49BV512, 64 KB: skipped.
Probing for Atmel AT49F002(N), 256 KB: skipped.
Probing for Atmel AT49F002(N)T, 256 KB: skipped.
Probing for AMIC A25L40PT, 512 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x2541
Probing for AMIC A25L40PU, 512 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x2541
Probing for AMIC A29002B, 256 KB: skipped.
Probing for AMIC A29002T, 256 KB: skipped.
Probing for AMIC A29040B, 512 KB: skipped.
Probing for AMIC A49LF040A, 512 KB: skipped.
Probing for EMST F49B002UA, 256 KB: skipped.
Probing for Eon EN25B05, 64 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x2541
Probing for Eon EN25B05T, 64 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x2541
Probing for Eon EN25B10, 128 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x2541
Probing for Eon EN25B10T, 128 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x2541
Probing for Eon EN25B20, 256 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x2541
Probing for Eon EN25B20T, 256 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x2541
Probing for Eon EN25B40, 512 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x2541
Probing for Eon EN25B40T, 512 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x2541
Probing for Eon EN25B80, 1024 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x2541
Probing for Eon EN25B80T, 1024 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x2541
Probing for Eon EN25B16, 2048 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x2541
Probing for Eon EN25B16T, 2048 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x2541
Probing for Eon EN25B32, 4096 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x2541
Probing for Eon EN25B32T, 4096 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x2541
Probing for Eon EN25B64, 8192 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x2541
Probing for Eon EN25B64T, 8192 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x2541
Probing for Eon EN25D16, 2048 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x2541
Probing for Eon EN25F05, 64 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x2541
Probing for Eon EN25F10, 128 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x2541
Probing for Eon EN25F20, 256 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x2541
Probing for Eon EN25F40, 512 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x2541
Probing for Eon EN25F80, 1024 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x2541
Probing for Eon EN25F16, 2048 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x2541
Probing for Eon EN25F32, 4096 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x2541
Probing for Eon EN29F010, 128 KB: skipped.
Probing for EON EN29F002(A)(N)B, 256 KB: skipped.
Probing for EON EN29F002(A)(N)T, 256 KB: skipped.
Probing for Fujitsu MBM29F004BC, 512 KB: skipped.
Probing for Fujitsu MBM29F004TC, 512 KB: skipped.
Probing for Fujitsu MBM29F400BC, 512 KB: skipped.
Probing for Fujitsu MBM29F400TC, 512 KB: skipped.
Probing for Intel 28F001BX-B, 128 KB: skipped.
Probing for Intel 28F001BX-T, 128 KB: skipped.
Probing for Intel 28F004S5, 512 KB: skipped.
Probing for Intel 28F004BV/BE-B, 512 KB: skipped.
Probing for Intel 28F004BV/BE-T, 512 KB: skipped.
Probing for Intel 28F400BV/CV/CE-B, 512 KB: skipped.
Probing for Intel 28F400BV/CV/CE-T, 512 KB: skipped.
Probing for Intel 82802AB, 512 KB: probe_82802ab: id1 0x20, id2 0x59, id1 is normal flash content, id2 is normal flash content
Probing for Intel 82802AC, 1024 KB: probe_82802ab: id1 0x38, id2 0x30, id1 is normal flash content, id2 is normal flash content
Probing for Macronix MX25L512, 64 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x2541
Probing for Macronix MX25L1005, 128 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x2541
Probing for Macronix MX25L2005, 256 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x2541
Probing for Macronix MX25L4005, 512 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x2541
Probing for Macronix MX25L8005, 1024 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x2541
Probing for Macronix MX25L1605, 2048 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x2541
Probing for Macronix MX25L1635D, 2048 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x2541
Probing for Macronix MX25L3205, 4096 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x2541
Probing for Macronix MX25L3235D, 4096 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x2541
Probing for Macronix MX25L6405, 8192 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x2541
Probing for Macronix MX25L12805, 16384 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x2541
Probing for Macronix MX29F001B, 128 KB: skipped.
Probing for Macronix MX29F001T, 128 KB: skipped.
Probing for Macronix MX29F002B, 256 KB: skipped.
Probing for Macronix MX29F002T, 256 KB: skipped.
Probing for Macronix MX29LV040, 512 KB: skipped.
Probing for Numonyx M25PE10, 128 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x2541
Probing for Numonyx M25PE20, 256 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x2541
Probing for Numonyx M25PE40, 512 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x2541
Probing for Numonyx M25PE80, 1024 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x2541
Probing for Numonyx M25PE16, 2048 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x2541
Probing for PMC Pm25LV010, 128 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x2541
Probing for PMC Pm25LV016B, 2048 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x2541
Probing for PMC Pm25LV020, 256 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x2541
Probing for PMC Pm25LV040, 512 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x2541
Probing for PMC Pm25LV080B, 1024 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x2541
Probing for PMC Pm25LV512, 64 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x2541
Probing for PMC Pm29F002T, 256 KB: skipped.
Probing for PMC Pm29F002B, 256 KB: skipped.
Probing for PMC Pm39LV010, 128 KB: skipped.
Probing for PMC Pm39LV020, 256 KB: skipped.
Probing for PMC Pm39LV040, 512 KB: skipped.
Probing for PMC Pm49FL002, 256 KB: probe_jedec_common: id1 0x2e, id2 0xc7, id1 parity violation, id1 is normal flash content, id2 is normal flash content
Probing for PMC Pm49FL004, 512 KB: probe_jedec_common: id1 0x20, id2 0x59, id1 is normal flash content, id2 is normal flash content
Probing for Sanyo LF25FW203A, 2048 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x2541
Probing for Sharp LHF00L04, 1024 KB: probe_82802ab: id1 0x38, id2 0x30, id1 is normal flash content, id2 is normal flash content
Probing for Spansion S25FL008A, 1024 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x2541
Probing for Spansion S25FL016A, 2048 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x2541
Probing for SST SST25VF016B, 2048 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x2541
Chip status register is 00
Chip status register: Block Protect Write Disable (BPL) is not set
Chip status register: Auto Address Increment Programming (AAI) is not set
Chip status register: Bit 5 / Block Protect 3 (BP3) is not set
Chip status register: Bit 4 / Block Protect 2 (BP2) is not set
Chip status register: Bit 3 / Block Protect 1 (BP1) is not set
Chip status register: Bit 2 / Block Protect 0 (BP0) is not set
Chip status register: Write Enable Latch (WEL) is not set
Chip status register: Write In Progress (WIP/BUSY) is not set
Resulting block protection : none
Found chip "SST SST25VF016B" (2048 KB, SPI) at physical address 0xffe00000.
Probing for SST SST25VF032B, 4096 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x2541
Probing for SST SST25VF040.REMS, 512 KB: probe_spi_rems: id1 0xbf, id2 0x41
Probing for SST SST25VF040B, 512 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x2541
Probing for SST SST25VF040B.REMS, 512 KB: probe_spi_rems: id1 0xbf, id2 0x41
Probing for SST SST25VF080B, 1024 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x2541
Probing for SST SST28SF040A, 512 KB: skipped.
Probing for SST SST29EE010, 128 KB: skipped.
Probing for SST SST29LE010, 128 KB: skipped.
Probing for SST SST29EE020A, 256 KB: skipped.
Probing for SST SST29LE020, 256 KB: skipped.
Probing for SST SST39SF512, 64 KB: skipped.
Probing for SST SST39SF010A, 128 KB: skipped.
Probing for SST SST39SF020A, 256 KB: skipped.
Probing for SST SST39SF040, 512 KB: skipped.
Probing for SST SST39VF512, 64 KB: skipped.
Probing for SST SST39VF010, 128 KB: skipped.
Probing for SST SST39VF020, 256 KB: skipped.
Probing for SST SST39VF040, 512 KB: skipped.
Probing for SST SST39VF080, 1024 KB: skipped.
Probing for SST SST49LF002A/B, 256 KB: probe_jedec_common: id1 0x2e, id2 0xc7, id1 parity violation, id1 is normal flash content, id2 is normal flash content
Probing for SST SST49LF003A/B, 384 KB: probe_jedec_common: id1 0xbb, id2 0x5d, id1 parity violation, id1 is normal flash content, id2 is normal flash content
Probing for SST SST49LF004A/B, 512 KB: probe_jedec_common: id1 0x20, id2 0x59, id1 is normal flash content, id2 is normal flash content
Probing for SST SST49LF004C, 512 KB: probe_82802ab: id1 0x20, id2 0x59, id1 is normal flash content, id2 is normal flash content
Probing for SST SST49LF008A, 1024 KB: probe_jedec_common: id1 0x38, id2 0x30, id1 is normal flash content, id2 is normal flash content
Probing for SST SST49LF008C, 1024 KB: probe_82802ab: id1 0x38, id2 0x30, id1 is normal flash content, id2 is normal flash content
Probing for SST SST49LF016C, 2048 KB: Chip size 2048 kB is bigger than supported size 1024 kB of chipset/board/programmer for FWH interface, probe/read/erase/write may fail. probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content
Probing for SST SST49LF020, 256 KB: skipped.
Probing for SST SST49LF020A, 256 KB: skipped.
Probing for SST SST49LF040, 512 KB: skipped.
Probing for SST SST49LF040B, 512 KB: skipped.
Probing for SST SST49LF080A, 1024 KB: skipped.
Probing for SST SST49LF160C, 2048 KB: skipped.
Probing for ST M25P05-A, 64 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x2541
Probing for ST M25P05.RES, 64 KB: Ignoring RES in favour of RDID.
Probing for ST M25P10-A, 128 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x2541
Probing for ST M25P10.RES, 128 KB: Ignoring RES in favour of RDID.
Probing for ST M25P20, 256 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x2541
Probing for ST M25P40, 512 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x2541
Probing for ST M25P40-old, 512 KB: Ignoring RES in favour of RDID.
Probing for ST M25P80, 1024 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x2541
Probing for ST M25P16, 2048 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x2541
Probing for ST M25P32, 4096 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x2541
Probing for ST M25P64, 8192 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x2541
Probing for ST M25P128, 16384 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x2541
Probing for ST M29F002B, 256 KB: skipped.
Probing for ST M29F002T/NT, 256 KB: skipped.
Probing for ST M29F040B, 512 KB: skipped.
Probing for ST M29F400BT, 512 KB: skipped.
Probing for ST M29W010B, 128 KB: skipped.
Probing for ST M29W040B, 512 KB: skipped.
Probing for ST M29W512B, 64 KB: skipped.
Probing for ST M50FLW040A, 512 KB: probe_82802ab: id1 0x20, id2 0x59, id1 is normal flash content, id2 is normal flash content
Probing for ST M50FLW040B, 512 KB: probe_82802ab: id1 0x20, id2 0x59, id1 is normal flash content, id2 is normal flash content
Probing for ST M50FLW080A, 1024 KB: probe_82802ab: id1 0x38, id2 0x30, id1 is normal flash content, id2 is normal flash content
Probing for ST M50FLW080B, 1024 KB: probe_82802ab: id1 0x38, id2 0x30, id1 is normal flash content, id2 is normal flash content
Probing for ST M50FW002, 256 KB: probe_82802ab: id1 0x2e, id2 0xc7, id1 parity violation, id1 is normal flash content, id2 is normal flash content
Probing for ST M50FW016, 2048 KB: Chip size 2048 kB is bigger than supported size 1024 kB of chipset/board/programmer for FWH interface, probe/read/erase/write may fail. probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content
Probing for ST M50FW040, 512 KB: probe_82802ab: id1 0x20, id2 0x59, id1 is normal flash content, id2 is normal flash content
Probing for ST M50FW080, 1024 KB: probe_82802ab: id1 0x38, id2 0x30, id1 is normal flash content, id2 is normal flash content
Probing for ST M50LPW116, 2048 KB: skipped.
Probing for SyncMOS S29C31004T, 512 KB: skipped.
Probing for SyncMOS S29C51001T, 128 KB: skipped.
Probing for SyncMOS S29C51002T, 256 KB: skipped.
Probing for SyncMOS S29C51004T, 512 KB: skipped.
Probing for TI TMS29F002RB, 256 KB: skipped.
Probing for TI TMS29F002RT, 256 KB: skipped.
Probing for Winbond W25Q80, 1024 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x2541
Probing for Winbond W25Q16, 2048 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x2541
Probing for Winbond W25Q32, 4096 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x2541
Probing for Winbond W25x10, 128 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x2541
Probing for Winbond W25x20, 256 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x2541
Probing for Winbond W25x40, 512 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x2541
Probing for Winbond W25x80, 1024 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x2541
Probing for Winbond W25x16, 2048 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x2541
Probing for Winbond W25x32, 4096 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x2541
Probing for Winbond W25x64, 8192 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x2541
Probing for Winbond W29C011, 128 KB: skipped.
Probing for Winbond W29C020C, 256 KB: skipped.
Probing for Winbond W29C040P, 512 KB: skipped.
Probing for Winbond W29EE011, 128 KB: skipped.
Probing for Winbond W39V040A, 512 KB: skipped.
Probing for Winbond W39V040B, 512 KB: skipped.
Probing for Winbond W39V040C, 512 KB: skipped.
Probing for Winbond W39V040FA, 512 KB: probe_jedec_common: id1 0x20, id2 0x59, id1 is normal flash content, id2 is normal flash content
Probing for Winbond W39V080A, 1024 KB: skipped.
Probing for Winbond W49F002U, 256 KB: skipped.
Probing for Winbond W49V002A, 256 KB: skipped.
Probing for Winbond W49V002FA, 256 KB: probe_jedec_common: id1 0x2e, id2 0xc7, id1 parity violation, id1 is normal flash content, id2 is normal flash content
Probing for Winbond W39V080FA, 1024 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0x38, id2 0x30, id1 is normal flash content, id2 is normal flash content
Probing for Winbond W39V080FA (dual mode), 512 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0x20, id2 0x59, id1 is normal flash content, id2 is normal flash content
Probing for Atmel unknown Atmel SPI chip, 0 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x2541
Probing for EON unknown EON SPI chip, 0 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x2541
Probing for Macronix unknown Macronix SPI chip, 0 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x2541
Probing for PMC unknown PMC SPI chip, 0 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x2541
Probing for SST unknown SST SPI chip, 0 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x2541
Probing for ST unknown ST SPI chip, 0 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x2541
Probing for Sanyo unknown Sanyo SPI chip, 0 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x2541
Probing for Generic unknown SPI chip (RDID), 0 KB: probe_spi_rdid_generic: id1 0xbf, id2 0x2541
Probing for Generic unknown SPI chip (REMS), 0 KB: probe_spi_rems: id1 0xbf, id2 0x41
===

Eamon

stephenw10

Ok, wonder why it didn't work the first time? Hmm.
Never mind, now you can read out the bios file and open it with a bios editor to see if it holds any secrets. It probably won't to be honest. Only the X-Core box had the ability to set the arm/disarm led status from the bios. It will let you see how easy it would be to unlock the bios menus. On the XTM5 it was simply a matter of changing to default access level but it was high risk as you've probably read in the xtm5 thread.

Steve

Eams

Yeah.. I think I might have downloaded the 64bit package when I was in fact running the 32bit nanobsd build - having tried so many different builds :P

Ok I've got the BIOS saved to disk, what do I use to open it and have a look, modbin6 from the freedos image?

Eamon