Watchguard Firebox XTM 8 Series

stephenw10

Something else while I think of it. You could potentially change the hardware resource settings for com2 in the BIOS so they use the com1 defaults. Of course you'd need to first mod the bios to open the settings. ;)

Steve

Eams

Not been on here as much as I expected recently however… I have made some progress!

Forgive me for the lack of PuTTY log for the UDMA/SMART message :(

I've managed to connect a monitor to the onboard VGA connector and I can now see whats happening!

Having gotten nowhere with the nanobsd serial builds due to it being complied for COM1 and this machine having no COM1, I've been trying with the vga builds as they output to text. However they were still no good - it didn't redirect the text screen to COM2 :(

While trying the above on build of pfSense-memstick-2.1-BETA1-i386-20130510-1628.img.gz I had the monitor attached but it's giving me errors about partitioning!

Eamon

![2013-05-13 18.21.30-small.jpg](/public/imported_attachments/1/2013-05-13 18.21.30-small.jpg)
![2013-05-13 18.21.30-small.jpg_thumb](/public/imported_attachments/1/2013-05-13 18.21.30-small.jpg_thumb)
![2013-05-13 18.21.53-small.jpg](/public/imported_attachments/1/2013-05-13 18.21.53-small.jpg)
![2013-05-13 18.21.53-small.jpg_thumb](/public/imported_attachments/1/2013-05-13 18.21.53-small.jpg_thumb)

Eams

Oh forgot to add, I connected a keyboard via usb and it works :)

Eamon

stephenw10

Loving your VGA hook up! ;)

The memstick image expects to be connected via USB so if you put it on a CF card it will probably complain.

So with the monitor connected you still can't boot the nano_vga image?
Hmm, I wonder if it set to use dual consoles. I suspect that anything hard coded to talk to the com1 resources will have a problem when they are not available. You'd hope it would fail gracefully but I no idea.

Steve

Eams

Haha, the vga hookup was one of two ways and this was easiest that didn't involve cutting any wires or anything.

Only connected green as I figured it'd let me see everything - apart from bold white!

I'm just writing a nano_vga image as I type on the sandisk 4gig cf card - this one will take the 4gig image!

Eamon

Eams

Getting some weird READ_DMA error.

Obligatory dmesg:

$ dmesg
Copyright 1992-2010 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 8.1-RELEASE-p13 #0: Fri Apr 12 11:55:06 EDT 2013
root@snapshots-8_1-amd64.builders.pfsense.org:/usr/obj.pfSense/usr/pfSensesrc/src/sys/pfSense_wrap_vga.8.amd64 amd64
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: Intel(R) Core(TM)2 Quad CPU Q9400 @ 2.66GHz (2660.01-MHz K8-class CPU)
Origin = "GenuineIntel" Id = 0x1067a Family = 6 Model = 17 Stepping = 10
Features=0xbfebfbff <fpu,vme,de,pse,tsc,msr,pae,mce,cx8,apic,sep,mtrr,pge,mca,cmov,pat,pse36,clflush,dts,acpi,mmx,fxsr,sse,sse2,ss,htt,tm,pbe>Features2=0x408e3fd <sse3,dtes64,mon,ds_cpl,vmx,smx,est,tm2,ssse3,cx16,xtpr,pdcm,sse4.1,xsave>AMD Features=0x20100800 <syscall,nx,lm>AMD Features2=0x1 <lahf>TSC: P-state invariant
real memory = 2147483648 (2048 MB)
avail memory = 2043940864 (1949 MB)
ACPI APIC Table: <120208 APIC1015>
FreeBSD/SMP: Multiprocessor System Detected: 4 CPUs
FreeBSD/SMP: 1 package(s) x 4 core(s)
cpu0 (BSP): APIC ID: 0
cpu1 (AP): APIC ID: 1
cpu2 (AP): APIC ID: 2
cpu3 (AP): APIC ID: 3
ioapic0 <version 2.0="">irqs 0-23 on motherboard
ipw_bss: You need to read the LICENSE file in /usr/share/doc/legal/intel_ipw/.
ipw_bss: If you agree with the license, set legal.intel_ipw.license_ack=1 in /boot/loader.conf.
module_register_init: MOD_LOAD (ipw_bss_fw, 0xffffffff8040b400, 0) error 1
wlan: mac acl policy registered
ipw_ibss: You need to read the LICENSE file in /usr/share/doc/legal/intel_ipw/.
ipw_ibss: If you agree with the license, set legal.intel_ipw.license_ack=1 in /boot/loader.conf.
module_register_init: MOD_LOAD (ipw_ibss_fw, 0xffffffff8040b4a0, 0) error 1
ipw_monitor: You need to read the LICENSE file in /usr/share/doc/legal/intel_ipw/.
ipw_monitor: If you agree with the license, set legal.intel_ipw.license_ack=1 in /boot/loader.conf.
module_register_init: MOD_LOAD (ipw_monitor_fw, 0xffffffff8040b540, 0) error 1
wpi: You need to read the LICENSE file in /usr/share/doc/legal/intel_wpi/.
wpi: If you agree with the license, set legal.intel_wpi.license_ack=1 in /boot/loader.conf.
module_register_init: MOD_LOAD (wpi_fw, 0xffffffff8058a010, 0) error 1
kbd1 at kbdmux0
cryptosoft0: <software crypto="">on motherboard
padlock0: No ACE support.
acpi0: <120208 XSDT1015> on motherboard
acpi0: [ITHREAD]
acpi0: Power Button (fixed)
acpi0: reservation of 0, a0000 (3) failed
acpi0: reservation of 100000, 7f600000 (3) failed
Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x808-0x80b on acpi0
cpu0: <acpi cpu="">on acpi0
cpu1: <acpi cpu="">on acpi0
cpu2: <acpi cpu="">on acpi0
cpu3: <acpi cpu="">on acpi0
pcib0: <acpi host-pci="" bridge="">port 0xcf8-0xcff on acpi0
pci0: <acpi pci="" bus="">on pcib0
pcib1: <acpi pci-pci="" bridge="">irq 16 at device 1.0 on pci0
pci7: <acpi pci="" bus="">on pcib1
pcib2: <pci-pci bridge="">mem 0xfe7e0000-0xfe7fffff irq 16 at device 0.0 on pci7
pci8: <pci bus="">on pcib2
pcib3: <pci-pci bridge="">irq 16 at device 0.0 on pci8
pci14: <pci bus="">on pcib3
pci14: <encrypt decrypt,="" network="" computer="" crypto="">at device 0.0 (no driver attached)
pcib4: <pci-pci bridge="">irq 17 at device 1.0 on pci8
pci13: <pci bus="">on pcib4
em0: <intel(r) 1000="" pro="" network="" connection="" 7.3.2="">port 0xec00-0xec1f mem 0xfebe0000-0xfebfffff,0xfebdc000-0xfebdffff irq 17 at device 0.0 on pci13
em0: Using MSIX interrupts with 3 vectors
em0: [ITHREAD]
em0: [ITHREAD]
em0: [ITHREAD]
pcib5: <pci-pci bridge="">irq 16 at device 4.0 on pci8
pci12: <pci bus="">on pcib5
pcib6: <pci-pci bridge="">irq 18 at device 6.0 on pci8
pci11: <pci bus="">on pcib6
em1: <intel(r) 1000="" pro="" network="" connection="" 7.3.2="">port 0xdc00-0xdc1f mem 0xfeae0000-0xfeafffff,0xfeadc000-0xfeadffff irq 18 at device 0.0 on pci11
em1: Using MSIX interrupts with 3 vectors
em1: [ITHREAD]
em1: [ITHREAD]
em1: [ITHREAD]
pcib7: <pci-pci bridge="">irq 16 at device 8.0 on pci8
pci10: <pci bus="">on pcib7
em2: <intel(r) 1000="" pro="" network="" connection="" 7.3.2="">port 0xcc00-0xcc1f mem 0xfe9e0000-0xfe9fffff,0xfe9dc000-0xfe9dffff irq 16 at device 0.0 on pci10
em2: Using MSIX interrupts with 3 vectors
em2: [ITHREAD]
em2: [ITHREAD]
em2: [ITHREAD]
pcib8: <pci-pci bridge="">irq 17 at device 9.0 on pci8
pci9: <pci bus="">on pcib8
em3: <intel(r) 1000="" pro="" network="" connection="" 7.3.2="">port 0xbc00-0xbc1f mem 0xfe8e0000-0xfe8fffff,0xfe8dc000-0xfe8dffff irq 17 at device 0.0 on pci9
em3: Using MSIX interrupts with 3 vectors
em3: [ITHREAD]
em3: [ITHREAD]
em3: [ITHREAD]
vgapci0: <vga-compatible display="">port 0x3800-0x3807 mem 0xfe100000-0xfe17ffff,0xd0000000-0xdfffffff,0xfe000000-0xfe0fffff irq 16 at device 2.0 on pci0
em4: <intel(r) 1000="" pro="" network="" connection="" 7.3.2="">port 0x3880-0x389f mem 0xfe1c0000-0xfe1dffff,0xfe1fe000-0xfe1fefff irq 20 at device 25.0 on pci0
em4: Using an MSI interrupt
em4: [FILTER]
pcib9: <acpi pci-pci="" bridge="">irq 17 at device 28.0 on pci0
pci6: <acpi pci="" bus="">on pcib9
em5: <intel(r) 1000="" pro="" network="" connection="" 7.3.2="">port 0xac00-0xac1f mem 0xfe6e0000-0xfe6fffff irq 16 at device 0.0 on pci6
em5: Using an MSI interrupt
em5: [FILTER]
pcib10: <acpi pci-pci="" bridge="">irq 16 at device 28.1 on pci0
pci5: <acpi pci="" bus="">on pcib10
em6: <intel(r) 1000="" pro="" network="" connection="" 7.3.2="">port 0x9c00-0x9c1f mem 0xfe5e0000-0xfe5fffff irq 17 at device 0.0 on pci5
em6: Using an MSI interrupt
em6: [FILTER]
pcib11: <acpi pci-pci="" bridge="">irq 18 at device 28.2 on pci0
pci4: <acpi pci="" bus="">on pcib11
em7: <intel(r) 1000="" pro="" network="" connection="" 7.3.2="">port 0x8c00-0x8c1f mem 0xfe4e0000-0xfe4fffff irq 18 at device 0.0 on pci4
em7: Using an MSI interrupt
em7: [FILTER]
pcib12: <acpi pci-pci="" bridge="">irq 19 at device 28.3 on pci0
pci3: <acpi pci="" bus="">on pcib12
em8: <intel(r) 1000="" pro="" network="" connection="" 7.3.2="">port 0x7c00-0x7c1f mem 0xfe3e0000-0xfe3fffff irq 19 at device 0.0 on pci3
em8: Using an MSI interrupt
em8: [FILTER]
pcib13: <acpi pci-pci="" bridge="">irq 17 at device 28.4 on pci0
pci2: <acpi pci="" bus="">on pcib13
em9: <intel(r) 1000="" pro="" network="" connection="" 7.3.2="">port 0x6c00-0x6c1f mem 0xfe2e0000-0xfe2fffff irq 16 at device 0.0 on pci2
em9: Using an MSI interrupt
em9: [FILTER]
uhci0: <intel 82801i="" (ich9)="" usb="" controller="">port 0x3c00-0x3c1f irq 23 at device 29.0 on pci0
uhci0: [ITHREAD]
usbus0: <intel 82801i="" (ich9)="" usb="" controller="">on uhci0
uhci1: <intel 82801i="" (ich9)="" usb="" controller="">port 0x4000-0x401f irq 19 at device 29.1 on pci0
uhci1: [ITHREAD]
usbus1: <intel 82801i="" (ich9)="" usb="" controller="">on uhci1
ehci0: <intel 82801i="" (ich9)="" usb="" 2.0="" controller="">mem 0xfe1ff800-0xfe1ffbff irq 23 at device 29.7 on pci0
ehci0: [ITHREAD]
usbus2: EHCI version 1.0
usbus2: <intel 82801i="" (ich9)="" usb="" 2.0="" controller="">on ehci0
pcib14: <acpi pci-pci="" bridge="">at device 30.0 on pci0
pci1: <acpi pci="" bus="">on pcib14
isab0: <pci-isa bridge="">at device 31.0 on pci0
isa0: <isa bus="">on isab0
atapci0: <intel ich9="" sata300="" controller="">port 0x4c00-0x4c07,0x4880-0x4883,0x4800-0x4807,0x4480-0x4483,0x4400-0x440f,0x4080-0x408f irq 19 at device 31.2 on pci0
atapci0: [ITHREAD]
ata2: <ata 0="" channel="">on atapci0
ata2: [ITHREAD]
ata3: <ata 1="" channel="">on atapci0
ata3: [ITHREAD]
pci0: <serial bus,="" smbus="">at device 31.3 (no driver attached)
atapci1: <intel ich9="" sata300="" controller="">port 0x5c00-0x5c07,0x5880-0x5883,0x5800-0x5807,0x5480-0x5483,0x5400-0x540f,0x5080-0x508f irq 19 at device 31.5 on pci0
atapci1: [ITHREAD]
ata4: <ata 0="" channel="">on atapci1
ata4: [ITHREAD]
ata5: <ata 1="" channel="">on atapci1
ata5: [ITHREAD]
acpi_button0: <power button="">on acpi0
atrtc0: <at realtime="" clock="">port 0x70-0x71 irq 8 on acpi0
uart1: <16550 or compatible> port 0x2f8-0x2ff irq 3 on acpi0
uart1: [FILTER]
ppc0: <parallel port="">port 0x378-0x37f irq 7 on acpi0
ppc0: Generic chipset (NIBBLE-only) in COMPATIBLE mode
ppc0: [ITHREAD]
ppbus0: <parallel port="" bus="">on ppc0
ppi0: <parallel i="" o="">on ppbus0
sc0: <system console="">at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
vga0: <generic isa="" vga="">at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
atkbdc0: <keyboard controller="" (i8042)="">at port 0x60,0x64 on isa0
atkbd0: <at keyboard="">irq 1 on atkbdc0
kbd0 at atkbd0
atkbd0: [GIANT-LOCKED]
atkbd0: [ITHREAD]
Timecounters tick every 10.000 msec
IPsec: Initialized Security Association Processing.
usbus0: 12Mbps Full Speed USB v1.0
usbus1: 12Mbps Full Speed USB v1.0
usbus2: 480Mbps High Speed USB v2.0
ad7: 3815MB <sandisk sdcfh-004g="" hdx="" 7.07="">at ata3-slave UDMA33 SATA 1.5Gb/s
ugen0.1: <intel>at usbus0
uhub0: <intel 1="" 9="" uhci="" root="" hub,="" class="" 0,="" rev="" 1.00="" 1.00,="" addr="">on usbus0
ugen1.1: <intel>at usbus1
uhub1: <intel 1="" 9="" uhci="" root="" hub,="" class="" 0,="" rev="" 1.00="" 1.00,="" addr="">on usbus1
ugen2.1: <intel>at usbus2
uhub2: <intel 1="" 9="" ehci="" root="" hub,="" class="" 0,="" rev="" 2.00="" 1.00,="" addr="">on usbus2
uhub0: 2 ports with 2 removable, self powered
uhub1: 2 ports with 2 removable, self powered
uhub2: 4 ports with 4 removable, self powered
ugen0.2: <chicony>at usbus0
ukbd0: <chicony 0="" 2="" usb="" keyboard,="" class="" 0,="" rev="" 2.00="" 1.57,="" addr="">on usbus0
kbd2 at ukbd0
ad7: FAILURE - READ_DMA timed out LBA=7813117
ad7: TIMEOUT - READ_DMA retrying (1 retry left) LBA=7813119
ad7: FAILURE - READ_DMA timed out LBA=7813103
ad7: TIMEOUT - READ_DMA retrying (0 retries left) LBA=7813119
ad7: FAILURE - READ_DMA timed out LBA=7813116
ad7: FAILURE - READ_DMA timed out LBA=7813119
ad7: FAILURE - READ_DMA timed out LBA=7813119
ad7: FAILURE - READ_DMA timed out LBA=7813119
SMP: AP CPU #1 Launched!
SMP: AP CPU #2 Launched!
SMP: AP CPU #3 Launched!
ad7: TIMEOUT - READ_DMA retrying (1 retry left) LBA=7813119
ad7: TIMEOUT - READ_DMA retrying (0 retries left) LBA=7813119
ad7: FAILURE - READ_DMA timed out LBA=7813119
Trying to mount root from ufs:/dev/ufs/pfsense0
ad7: FAILURE - SETFEATURES 0x85 status=51 <ready,dsc,error>error=4 <aborted>pflog0: promiscuous mode enabled
ad7: TIMEOUT - READ_DMA retrying (1 retry left) LBA=7813119
ad7: TIMEOUT - READ_DMA retrying (0 retries left) LBA=7813119
ad7: FAILURE - READ_DMA timed out LBA=7813119
ad7: TIMEOUT - READ_DMA retrying (1 retry left) LBA=7813119
ad7: TIMEOUT - READ_DMA retrying (0 retries left) LBA=7813119

Eamon</aborted></ready,dsc,error></chicony></chicony></intel></intel></intel></intel></intel></intel></sandisk></at></keyboard></generic></system></parallel></parallel></parallel></at></power></ata></ata></intel></serial></ata></ata></intel></isa></pci-isa></acpi></acpi></intel></intel></intel></intel></intel></intel></intel(r)></acpi></acpi></intel(r)></acpi></acpi></intel(r)></acpi></acpi></intel(r)></acpi></acpi></intel(r)></acpi></acpi></intel(r)></vga-compatible></intel(r)></pci></pci-pci></intel(r)></pci></pci-pci></intel(r)></pci></pci-pci></pci></pci-pci></intel(r)></pci></pci-pci></encrypt></pci></pci-pci></pci></pci-pci></acpi></acpi></acpi></acpi></acpi></acpi></acpi></acpi></software></version></lahf></syscall,nx,lm></sse3,dtes64,mon,ds_cpl,vmx,smx,est,tm2,ssse3,cx16,xtpr,pdcm,sse4.1,xsave></fpu,vme,de,pse,tsc,msr,pae,mce,cx8,apic,sep,mtrr,pge,mca,cmov,pat,pse36,clflush,dts,acpi,mmx,fxsr,sse,sse2,ss,htt,tm,pbe>

stephenw10

Right, that's what I mentioned earlier. The nanobsd_vga images have DMA enabled because of a specific device but many CF card slots do not have enough pins. Probably that's what's happening here.
Interrupt the boot process at the loader menu and do this:
http://doc.pfsense.org/index.php/Booting_Options#Disable_DMA_for_IDE_drives

Steve

wallabybob

My suspicion, based on the high LBA reported, is that your 4GB card is a bit short of providing 4GiB (1024 x 1024 x 1024) and the 4G image didn't quite fit. Some people have had to put a 2GB image on a "4GB" card/stick. Note the card is reported having 3815MB which would allow a LBA of up to around 7630000 which is a bit short of the reported LBAs.

If I recall correctly, the FreeBSD GEOM component goes looking for a GEOM signature on the apparent last sector or two of the disk.

Eams

I put a 2g nano_vga 64bit image on the same card and got the same LBA error.

Did the set hw.ata.atapi_dma=0 thing too which stopped the LBA errors, however got a different LBA error!

ad7: 3815MB <sandisk sdcfh-004g="" hdx="" 7.07="">at ata3-slave PIO4 SATA 1.5Gb/s
ad7: FAILURE - READ status=51 <ready,dsc,error>error=10 <nid_not_found>LBA=7813117
ad7: FAILURE - READ status=51 <ready,dsc,error>error=10 <nid_not_found>LBA=7813119
ad7: FAILURE - READ status=51 <ready,dsc,error>error=10 <nid_not_found>LBA=7813103
ad7: FAILURE - READ status=51 <ready,dsc,error>error=10 <nid_not_found>LBA=7813116
ad7: FAILURE - READ status=51 <ready,dsc,error>error=10 <nid_not_found>LBA=7813119
ad7: FAILURE - READ status=51 <ready,dsc,error>error=10 <nid_not_found>LBA=7813119
SMP: AP CPU #2 Launched!
SMP: AP CPU #1 Launched!
SMP: AP CPU #3 Launched!
ugen0.u1g:ue gn <e2i.nn11t.:e 1l:<="">I <naittne ltue="">s lb>au ts a0tus
ubsubsu2s
u1h
ub0: <intel 1="" 9="" uhci="" root="" hub,="" class="" 0,="" rev="" 1.00="" 1.00,="" addr="">on usbus0
uhub1: <intel 1="" 9="" ehci="" root="" hub,="" class="" 0,="" rev="" 2.00="" 1.00,="" addr="">on usbus2
uhub2: <intel 1="" 9="" uhci="" root="" hub,="" class="" 0,="" rev="" 1.00="" 1.00,="" addr="">on usbus1
ad7: FAILURE - READ status=51 <ready,dsc,error>error=10 <nid_not_found>LBA=7813119
Root mount waiting for: usbus2 usbus1 usbus0
uhub2: 2 ports with 2 removable, self powered
uhub0: 2 ports with 2 removable, self powered
Root mount waiting for: usbus2
uhub1: 4 ports with 4 removable, self powered
Trying to mount root from ufs:/dev/ufs/pfsense0
ad7: FAILURE - SETFEATURES 0x85 status=51 <ready,dsc,error>error=4 <aborted>ugen0.2: <chicony>at usbus0
ukbd0: <chicony 0="" 2="" usb="" keyboard,="" class="" 0,="" rev="" 2.00="" 1.57,="" addr="">on usbus0
kbd2 at ukbd0
pflog0: promiscuous mode enabled
ad7: FAILURE - READ status=51 <ready,dsc,error>error=10 <nid_not_found>LBA=7813119
ad7: FAILURE - READ status=51 <ready,dsc,error>error=10 <nid_not_found>LBA=7813119
ad7: FAILURE - READ status=51 <ready,dsc,error>error=10 <nid_not_found>LBA=7813119
ad7: FAILURE - READ status=51 <ready,dsc,error>error=10 <nid_not_found>LBA=7813119
ad7: FAILURE - READ status=51 <ready,dsc,error>error=10 <nid_not_found>LBA=7813119
ad7: FAILURE - READ status=51 <ready,dsc,error>error=10 <nid_not_found>LBA=7813119
ad7: FAILURE - READ status=51 <ready,dsc,error>error=10 <nid_not_found>LBA=7813119
ad7: FAILURE - READ status=51 <ready,dsc,error>error=10 <nid_not_found>LBA=7813119
ad7: FAILURE - READ status=51 <ready,dsc,error>error=10 <nid_not_found>LBA=7813119
ad7: FAILURE - READ status=51 <ready,dsc,error>error=10 <nid_not_found>LBA=7813119

Burning 2g nano_vga 32bit gives the same error on the same card (4gig SanDisk Ultra)

Booting up on the no name cf card with the same 32bit 2g nano_vga image gives no errors - no ser hw.ata.ata_dma=0 performed - wierd;

ad7: 3639MB <cf card="" ver5.04="">at ata3-slave UDMA33 SATA 1.5Gb/s
SMP: AP CPU #2 Launched!
SMP: AP CPU #1 Launched!
SMP: AP CPU #3 Launched!
ugen0u.1g:e n<2I.n1t:e l<>I natte l>u saubtu guss0beuns1
2.1
: <intel>at usbus1
uhub0: <intel 1="" 9="" uhci="" root="" hub,="" class="" 0,="" rev="" 1.00="" 1.00,="" addr="">on usbus0
uhub1: <intel 1="" 9="" uhci="" root="" hub,="" class="" 0,="" rev="" 1.00="" 1.00,="" addr="">on usbus1
uhub2: <intel 1="" 9="" ehci="" root="" hub,="" class="" 0,="" rev="" 2.00="" 1.00,="" addr="">on usbus2
Root mount waiting for: usbus2 usbus1 usbus0
uhub1: 2 ports with 2 removable, self powered
uhub0: 2 ports with 2 removable, self powered
Root mount waiting for: usbus2
uhub2: 4 ports with 4 removable, self powered
Trying to mount root from ufs:/dev/ufs/pfsense0
ugen0.2: <chicony>at usbus0
ukbd0: <chicony 0="" 2="" usb="" keyboard,="" class="" 0,="" rev="" 2.00="" 1.57,="" addr="">on usbus0
kbd2 at ukbd0
pflog0: promiscuous mode enabled

How very bizarre.

Eamon</chicony></chicony></intel></intel></intel></intel></cf></nid_not_found></ready,dsc,error></nid_not_found></ready,dsc,error></nid_not_found></ready,dsc,error></nid_not_found></ready,dsc,error></nid_not_found></ready,dsc,error></nid_not_found></ready,dsc,error></nid_not_found></ready,dsc,error></nid_not_found></ready,dsc,error></nid_not_found></ready,dsc,error></nid_not_found></ready,dsc,error></chicony></chicony></aborted></ready,dsc,error></nid_not_found></ready,dsc,error></intel></intel></intel></naittne></e2i.nn11t.:e></nid_not_found></ready,dsc,error></nid_not_found></ready,dsc,error></nid_not_found></ready,dsc,error></nid_not_found></ready,dsc,error></nid_not_found></ready,dsc,error></nid_not_found></ready,dsc,error></sandisk>

stephenw10

The 'nid not found' error is common and nothing to worry about:
http://doc.pfsense.org/index.php/DMA_and_LBA_Errors

I would guess that your no-name card is not DMA capable so didn't cause the problem.

Did it boot successfully then?

Steve

Eams

Damn I bought the exact same cf card that's in that link! I guess that's that error sorted then.

Yes it did boot, even with the LBA errors, looks like it was a combination of both errors mentioned by yourself and wallabybob.
Its pretty nippy to say the least ;)
I gotta figure out how to set it up now. At least 10x GbE ports gives me plenty to play with haha!

I've contacted Lanner to see if I can get the BIOS for the 8750 this is based on, that would help even further.

Eamon

fmertz

@Eams:

The LCD seems to be the same as previous models as you say so should be ok.

There is an arm/disarm led on the front, it hasn't lit up yet.

There is some useful info there about the FW-8750 of which this board seems to be from:

Platform
Chipset: Intel Q35 + ICH9D0

Eamon

The LCD code assumes parallel port, so, at a minimum, the sdeclcd driver part of the lcdproc package should run. Might even work, too.

For the LEDs, the driver code supports the various models based on standard PCI detection of the ICH. We definitely need to add an entry for this ICH9 in the driver code. Once you guys get around to it, can you confirm this is, in fact, an ICH9D0, identified by Vendor x8086, device x2914 (the numbers are listed on page 12 of the "Intel I/O Controller Hub 9 (ICH9) Family Specification Update")?

Generally, the LEDs can be wired off of the GPIO device part of this ICH (like in the older models), but, more likely, they are wired off of the SuperIO chip (like the XTM 5). A further screen shot seems to list an ITE8718. This is where the research comes in to identify which line these LEDs are wired off of. I'll be happy to code this in when it is discovered.

stephenw10

Commence experimental probing! ;D

Since you don't have the Watchguard OS we can't look for clues in it's boot messages.

Not using a Winbond sio chip, interesting.

You could extract the bios code with flashrom and look at it for hidden menus.

Steve

Edit: Looks to be supported by superiotool as well.

Eams

fmertz:
Ok, fired up lcdproc, but nothing seems to happen :(

The boot up screen shows 'Starting package LCDproc…done.'

Under Status: Services it shows as Stopped. Clicking to start it doesn't change it's status.

ICH9 Chipset - think you were right, experimental probe..:

$ pciconf -lc
hostb0@pci0:0:0:0: class=0x060000 card=0x29b08086 chip=0x29b08086 rev=0x02 hdr=0x00
cap 09[e0] = vendor (length 11) Intel cap 11 version 1
pcib1@pci0:0:1:0: class=0x060400 card=0x29b18086 chip=0x29b18086 rev=0x02 hdr=0x01
cap 0d[88] = PCI Bridge card=0x29b18086
cap 01[80] = powerspec 3 supports D0 D3 current D0
cap 05[90] = MSI supports 1 message
cap 10[a0] = PCI-Express 1 root port max data 128(128) link x4(x16)
vgapci0@pci0:0:2:0: class=0x030000 card=0x29b28086 chip=0x29b28086 rev=0x02 hdr=0x00
cap 05[90] = MSI supports 1 message
cap 01[d0] = powerspec 2 supports D0 D3 current D0
em4@pci0:0:25:0: class=0x020000 card=0x00008086 chip=0x10bd8086 rev=0x02 hdr=0x00
cap 01[c8] = powerspec 2 supports D0 D3 current D0
cap 05[d0] = MSI supports 1 message, 64 bit enabled with 1 message
cap 13[e0] = PCI Advanced Features: FLR TP
pcib9@pci0:0:28:0: class=0x060400 card=0x29408086 chip=0x29408086 rev=0x02 hdr=0x01
cap 10[40] = PCI-Express 1 root port max data 128(128) link x1(x1)
cap 05[80] = MSI supports 1 message
cap 0d[90] = PCI Bridge card=0x29408086
cap 01[a0] = powerspec 2 supports D0 D3 current D0
pcib10@pci0:0:28:1: class=0x060400 card=0x29428086 chip=0x29428086 rev=0x02 hdr=0x01
cap 10[40] = PCI-Express 1 root port max data 128(128) link x1(x1)
cap 05[80] = MSI supports 1 message
cap 0d[90] = PCI Bridge card=0x29428086
cap 01[a0] = powerspec 2 supports D0 D3 current D0
pcib11@pci0:0:28:2: class=0x060400 card=0x29448086 chip=0x29448086 rev=0x02 hdr=0x01
cap 10[40] = PCI-Express 1 root port max data 128(128) link x1(x1)
cap 05[80] = MSI supports 1 message
cap 0d[90] = PCI Bridge card=0x29448086
cap 01[a0] = powerspec 2 supports D0 D3 current D0
pcib12@pci0:0:28:3: class=0x060400 card=0x29468086 chip=0x29468086 rev=0x02 hdr=0x01
cap 10[40] = PCI-Express 1 root port max data 128(128) link x1(x1)
cap 05[80] = MSI supports 1 message
cap 0d[90] = PCI Bridge card=0x29468086
cap 01[a0] = powerspec 2 supports D0 D3 current D0
pcib13@pci0:0:28:4: class=0x060400 card=0x29488086 chip=0x29488086 rev=0x02 hdr=0x01
cap 10[40] = PCI-Express 1 root port max data 128(128) link x1(x1)
cap 05[80] = MSI supports 1 message
cap 0d[90] = PCI Bridge card=0x29488086
cap 01[a0] = powerspec 2 supports D0 D3 current D0
uhci0@pci0:0:29:0: class=0x0c0300 card=0x29348086 chip=0x29348086 rev=0x02 hdr=0x00
cap 13[50] = PCI Advanced Features: FLR TP
uhci1@pci0:0:29:1: class=0x0c0300 card=0x29358086 chip=0x29358086 rev=0x02 hdr=0x00
cap 13[50] = PCI Advanced Features: FLR TP
ehci0@pci0:0:29:7: class=0x0c0320 card=0x293a8086 chip=0x293a8086 rev=0x02 hdr=0x00
cap 01[50] = powerspec 2 supports D0 D3 current D0
cap 0a[58] = EHCI Debug Port at offset 0xa0 in map 0x14
cap 13[98] = PCI Advanced Features: FLR TP
pcib14@pci0:0:30:0: class=0x060401 card=0x244e8086 chip=0x244e8086 rev=0x92 hdr=0x01
cap 0d[50] = PCI Bridge card=0x244e8086
isab0@pci0:0:31:0: class=0x060100 card=0x29148086 chip=0x29148086 rev=0x02 hdr=0x00
cap 09[e0] = vendor (length 12) Intel cap 1 version 0
features: SATA RAID-5, 4 PCI-e x1 slots
atapci0@pci0:0:31:2: class=0x01018f card=0x29208086 chip=0x29208086 rev=0x02 hdr=0x00
cap 01[70] = powerspec 3 supports D0 D3 current D0
cap 13[b0] = PCI Advanced Features: FLR TP
none0@pci0:0:31:3: class=0x0c0500 card=0x29308086 chip=0x29308086 rev=0x02 hdr=0x00
atapci1@pci0:0:31:5: class=0x010185 card=0x29268086 chip=0x29268086 rev=0x02 hdr=0x00
cap 01[70] = powerspec 3 supports D0 D3 current D0
cap 13[b0] = PCI Advanced Features: FLR TP
pcib2@pci0:7:0:0: class=0x060400 card=0x862410b5 chip=0x862410b5 rev=0xbb hdr=0x01
cap 01[40] = powerspec 3 supports D0 D3 current D0
cap 05[48] = MSI supports 4 messages, 64 bit, vector masks
cap 10[68] = PCI-Express 2 upstream port max data 128(2048) link x4(x4)
cap 0d[a4] = PCI Bridge card=0x862410b5
pcib3@pci0:8:0:0: class=0x060400 card=0x862410b5 chip=0x862410b5 rev=0xbb hdr=0x01
cap 01[40] = powerspec 3 supports D0 D3 current D0
cap 05[48] = MSI supports 4 messages, 64 bit, vector masks
cap 10[68] = PCI-Express 2 downstream port max data 128(2048) link x4(x4)
cap 0d[a4] = PCI Bridge card=0x862410b5
pcib4@pci0:8:1:0: class=0x060400 card=0x862410b5 chip=0x862410b5 rev=0xbb hdr=0x01
cap 01[40] = powerspec 3 supports D0 D3 current D0
cap 05[48] = MSI supports 4 messages, 64 bit, vector masks
cap 10[68] = PCI-Express 2 downstream port max data 128(2048) link x1(x4)
cap 0d[a4] = PCI Bridge card=0x862410b5
pcib5@pci0:8:4:0: class=0x060400 card=0x862410b5 chip=0x862410b5 rev=0xbb hdr=0x01
cap 01[40] = powerspec 3 supports D0 D3 current D0
cap 05[48] = MSI supports 4 messages, 64 bit, vector masks
cap 10[68] = PCI-Express 2 downstream port max data 128(2048) link x0(x8)
cap 0d[a4] = PCI Bridge card=0x862410b5
pcib6@pci0:8:6:0: class=0x060400 card=0x862410b5 chip=0x862410b5 rev=0xbb hdr=0x01
cap 01[40] = powerspec 3 supports D0 D3 current D0
cap 05[48] = MSI supports 4 messages, 64 bit, vector masks
cap 10[68] = PCI-Express 2 downstream port max data 128(2048) link x1(x4)
cap 0d[a4] = PCI Bridge card=0x862410b5
pcib7@pci0:8:8:0: class=0x060400 card=0x862410b5 chip=0x862410b5 rev=0xbb hdr=0x01
cap 01[40] = powerspec 3 supports D0 D3 current D0
cap 05[48] = MSI supports 4 messages, 64 bit, vector masks
cap 10[68] = PCI-Express 2 downstream port max data 128(2048) link x1(x4)
cap 0d[a4] = PCI Bridge card=0x862410b5
pcib8@pci0:8:9:0: class=0x060400 card=0x862410b5 chip=0x862410b5 rev=0xbb hdr=0x01
cap 01[40] = powerspec 3 supports D0 D3 current D0
cap 05[48] = MSI supports 4 messages, 64 bit, vector masks
cap 10[68] = PCI-Express 2 downstream port max data 128(2048) link x1(x4)
cap 0d[a4] = PCI Bridge card=0x862410b5
none1@pci0:14:0:0: class=0x100000 card=0x0001177d chip=0x0010177d rev=0x01 hdr=0x00
cap 01[40] = powerspec 3 supports D0 D3 current D0
cap 05[50] = MSI supports 1 message, 64 bit
cap 10[70] = PCI-Express 1 endpoint max data 128(256) link x4(x4)
em0@pci0:13:0:0: class=0x020000 card=0x00008086 chip=0x10d38086 rev=0x00 hdr=0x00
cap 01[c8] = powerspec 2 supports D0 D3 current D0
cap 05[d0] = MSI supports 1 message, 64 bit
cap 10[e0] = PCI-Express 1 endpoint max data 128(256) link x1(x1)
cap 11[a0] = MSI-X supports 3 messages in map 0x1c enabled
em1@pci0:11:0:0: class=0x020000 card=0x00008086 chip=0x10d38086 rev=0x00 hdr=0x00
cap 01[c8] = powerspec 2 supports D0 D3 current D0
cap 05[d0] = MSI supports 1 message, 64 bit
cap 10[e0] = PCI-Express 1 endpoint max data 128(256) link x1(x1)
cap 11[a0] = MSI-X supports 3 messages in map 0x1c enabled
em2@pci0:10:0:0: class=0x020000 card=0x00008086 chip=0x10d38086 rev=0x00 hdr=0x00
cap 01[c8] = powerspec 2 supports D0 D3 current D0
cap 05[d0] = MSI supports 1 message, 64 bit
cap 10[e0] = PCI-Express 1 endpoint max data 128(256) link x1(x1)
cap 11[a0] = MSI-X supports 3 messages in map 0x1c enabled
em3@pci0:9:0:0: class=0x020000 card=0x00008086 chip=0x10d38086 rev=0x00 hdr=0x00
cap 01[c8] = powerspec 2 supports D0 D3 current D0
cap 05[d0] = MSI supports 1 message, 64 bit
cap 10[e0] = PCI-Express 1 endpoint max data 128(256) link x1(x1)
cap 11[a0] = MSI-X supports 3 messages in map 0x1c enabled
em5@pci0:6:0:0: class=0x020000 card=0x00008086 chip=0x109a8086 rev=0x00 hdr=0x00
cap 01[c8] = powerspec 2 supports D0 D3 current D0
cap 05[d0] = MSI supports 1 message, 64 bit enabled with 1 message
cap 10[e0] = PCI-Express 1 endpoint max data 128(256) link x1(x1)
em6@pci0:5:0:0: class=0x020000 card=0x00008086 chip=0x109a8086 rev=0x00 hdr=0x00
cap 01[c8] = powerspec 2 supports D0 D3 current D0
cap 05[d0] = MSI supports 1 message, 64 bit enabled with 1 message
cap 10[e0] = PCI-Express 1 endpoint max data 128(256) link x1(x1)
em7@pci0:4:0:0: class=0x020000 card=0x00008086 chip=0x109a8086 rev=0x00 hdr=0x00
cap 01[c8] = powerspec 2 supports D0 D3 current D0
cap 05[d0] = MSI supports 1 message, 64 bit enabled with 1 message
cap 10[e0] = PCI-Express 1 endpoint max data 128(256) link x1(x1)
em8@pci0:3:0:0: class=0x020000 card=0x00008086 chip=0x109a8086 rev=0x00 hdr=0x00
cap 01[c8] = powerspec 2 supports D0 D3 current D0
cap 05[d0] = MSI supports 1 message, 64 bit enabled with 1 message
cap 10[e0] = PCI-Express 1 endpoint max data 128(256) link x1(x1)
em9@pci0:2:0:0: class=0x020000 card=0x00008086 chip=0x109a8086 rev=0x00 hdr=0x00
cap 01[c8] = powerspec 2 supports D0 D3 current D0
cap 05[d0] = MSI supports 1 message, 64 bit enabled with 1 message
cap 10[e0] = PCI-Express 1 endpoint max data 128(256) link x1(x1)

Stephen:
I managed to upload superiotool to /tmp/ but don't know how to run it :(

Ditto flashrom!

Eamon

Eams

Another experimental probe..

$ sysctl hw
hw.machine: i386
hw.model: Intel(R) Core(TM)2 Quad CPU Q9400 @ 2.66GHz
hw.ncpu: 4
hw.byteorder: 1234
hw.physmem: 2120441856
hw.usermem: 2066382848
hw.pagesize: 4096
hw.floatingpoint: 1
hw.machine_arch: i386
hw.realmem: 2137784320
hw.amr.force_sg32: 0
hw.an.an_cache_iponly: 1
hw.an.an_cache_mcastonly: 0
hw.an.an_cache_mode: dbm
hw.an.an_dump: off
hw.ata.setmax: 0
hw.ata.wc: 1
hw.ata.atapi_dma: 1
hw.ata.ata_dma_check_80pin: 1
hw.ata.ata_dma: 1
hw.ath.bstuck: 4
hw.ath.txbuf: 200
hw.ath.rxbuf: 40
hw.ath.resetcal: 1200
hw.ath.shortcal: 100
hw.ath.longcal: 30
hw.ath.hal.swba_backoff: 0
hw.ath.hal.sw_brt: 10
hw.ath.hal.dma_brt: 2
hw.bce.msi_enable: 1
hw.bce.tso_enable: 1
hw.bge.allow_asf: 0
hw.bt848.slow_msp_audio: -1
hw.bt848.format: -1
hw.bt848.reverse_mute: -1
hw.bt848.tuner: -1
hw.bt848.card: -1
hw.bwn.wme: 1
hw.bwn.usedma: 1
hw.bwn.hwpctl: 0
hw.bwn.bluetooth: 1
hw.bwn.bfp: 0
hw.cardbus.cis_debug: 0
hw.cardbus.debug: 0
hw.cxgb.snd_queue_len: 128
hw.cxgb.use_16k_clusters: -1
hw.cxgb.force_fw_update: 0
hw.cxgb.multiq: 1
hw.cxgb.ofld_disable: 0
hw.cxgb.msi_allowed: 2
hw.cxgb.tx_reclaim_threshold: 32
hw.cxgb.tx_coalesce_enable_stop: 256
hw.cxgb.tx_coalesce_enable_start: 512
hw.cxgb.tx_coalesce_force: 0
hw.cxgb.txq_mr_size: 1024
hw.em.eee_setting: 0
hw.em.rx_process_limit: 100
hw.em.enable_msix: 1
hw.em.sbp: 0
hw.em.smart_pwr_down: 0
hw.em.txd: 1024
hw.em.rxd: 1024
hw.em.rx_abs_int_delay: 66
hw.em.tx_abs_int_delay: 66
hw.em.rx_int_delay: 0
hw.em.tx_int_delay: 66
hw.igb.rx_process_limit: 100
hw.igb.num_queues: 0
hw.igb.header_split: 0
hw.igb.max_interrupt_rate: 8000
hw.igb.enable_msix: 1
hw.igb.enable_aim: 1
hw.igb.txd: 1024
hw.igb.rxd: 1024
hw.firewire.hold_count: 0
hw.firewire.try_bmr: 1
hw.firewire.fwmem.speed: 2
hw.firewire.fwmem.eui64_lo: 0
hw.firewire.fwmem.eui64_hi: 0
hw.firewire.phydma_enable: 1
hw.firewire.nocyclemaster: 0
hw.firewire.fwe.rx_queue_len: 128
hw.firewire.fwe.tx_speed: 2
hw.firewire.fwe.stream_ch: 1
hw.firewire.sbp.tags: 0
hw.firewire.sbp.use_doorbell: 0
hw.firewire.sbp.scan_delay: 500
hw.firewire.sbp.login_delay: 1000
hw.firewire.sbp.exclusive_login: 1
hw.firewire.sbp.max_speed: -1
hw.firewire.sbp.auto_login: 1
hw.hifn.maxbatch: 1
hw.hifn.debug: 0
hw.malo.txbuf: 256
hw.malo.rxquota: 256
hw.malo.rxbuf: 256
hw.malo.txcoalesce: 8
hw.malo.pci.msi_disable: 0
hw.mfi.max_cmds: 128
hw.mfi.event_class: 0
hw.mfi.event_locale: 65535
hw.mwl.rxdmalow: 3
hw.mwl.rxquota: 640
hw.mwl.txcoalesce: 8
hw.mwl.txbuf: 256
hw.mwl.rxbuf: 640
hw.mwl.rxdesc: 256
hw.pccard.cis_debug: 0
hw.pccard.debug: 0
hw.cbb.debug: 0
hw.cbb.start_32_io: 4096
hw.cbb.start_16_io: 256
hw.cbb.start_memory: 2281701376
hw.pcic.pd6722_vsense: 1
hw.pcic.intr_mask: 57016
hw.pci.usb_early_takeover: 1
hw.pci.honor_msi_blacklist: 1
hw.pci.enable_msix: 1
hw.pci.enable_msi: 1
hw.pci.do_power_resume: 1
hw.pci.do_power_nodriver: 0
hw.pci.enable_io_modes: 1
hw.pci.default_vgapci_unit: -1
hw.pci.host_mem_start: 2147483648
hw.pci.mcfg: 1
hw.pci.irq_override_mask: 57080
hw.safe.rngmaxalarm: 8
hw.safe.rngbufsize: 16
hw.safe.rnginterval: 1
hw.syscons.kbd_debug: 1
hw.syscons.kbd_reboot: 0
hw.syscons.bell: 1
hw.syscons.saver.keybonly: 1
hw.syscons.sc_no_suspend_vtswitch: 0
hw.usb.no_boot_wait: 0
hw.usb.debug: 0
hw.usb.usb_lang_mask: 255
hw.usb.usb_lang_id: 9
hw.usb.template: 0
hw.usb.power_timeout: 30
hw.usb.uath.regdomain: 0
hw.usb.uath.countrycode: 0
hw.usb.urtw.preamble_mode: 2
hw.usb.urtw.debug: 0
hw.usb.ucom.cons_baud: 9600
hw.usb.ucom.cons_unit: -1
hw.wi.debug: 0
hw.wi.txerate: 0
hw.intr_storm_threshold: 1000
hw.pagesizes: 4096 0
hw.availpages: 517686
hw.bus.devctl_queue: 1000
hw.bus.devctl_disable: 0
hw.kbd.keymap_restrict_change: 0
hw.nve_pollinterval: 0
hw.busdma.total_bpages: 128
hw.busdma.zone0.total_bpages: 128
hw.busdma.zone0.free_bpages: 128
hw.busdma.zone0.reserved_bpages: 0
hw.busdma.zone0.active_bpages: 0
hw.busdma.zone0.total_bounced: 0
hw.busdma.zone0.total_deferred: 0
hw.busdma.zone0.lowaddr: 0xffffffff
hw.busdma.zone0.alignment: 4096
hw.clockrate: 2660
hw.via_feature_xcrypt: 0
hw.via_feature_rng: 0
hw.instruction_sse: 1
hw.apic.enable_extint: 0
hw.mca.erratum383: 0
hw.mca.amd10h_L1TP: 1
hw.mca.enabled: 1
hw.mca.count: 0
hw.mca.interval: 3600
hw.mca.force_scan: 0
hw.acpi.supported_sleep_state: S1 S4 S5
hw.acpi.power_button_state: S5
hw.acpi.sleep_button_state: S1
hw.acpi.lid_switch_state: NONE
hw.acpi.standby_state: S1
hw.acpi.suspend_state: NONE
hw.acpi.sleep_delay: 1
hw.acpi.s4bios: 0
hw.acpi.verbose: 0
hw.acpi.disable_on_reboot: 0
hw.acpi.handle_reboot: 0
hw.acpi.reset_video: 0
hw.acpi.cpu.cx_lowest: C1

Eamon

Eams

Another..

$ sysctl dev.cpu
dev.cpu.0.%desc: ACPI CPU
dev.cpu.0.%driver: cpu
dev.cpu.0.%location: handle=_PR_.P001
dev.cpu.0.%pnpinfo: _HID=none UID=0
dev.cpu.0.%parent: acpi0
dev.cpu.0.cx_supported: C1/0
dev.cpu.0.cx_lowest: C1
dev.cpu.0.cx_usage: 100.00% last 5000us
dev.cpu.0.freq: 330
dev.cpu.0.freq_levels: 2646/-1 2315/-1 1984/-1 1653/-1 1323/-1 992/-1 661/-1 330/-1
dev.cpu.1.%desc: ACPI CPU
dev.cpu.1.%driver: cpu
dev.cpu.1.%location: handle=_PR.P002
dev.cpu.1.%pnpinfo: _HID=none UID=0
dev.cpu.1.%parent: acpi0
dev.cpu.1.cx_supported: C1/0
dev.cpu.1.cx_lowest: C1
dev.cpu.1.cx_usage: 100.00% last 5000us
dev.cpu.2.%desc: ACPI CPU
dev.cpu.2.%driver: cpu
dev.cpu.2.%location: handle=_PR.P003
dev.cpu.2.%pnpinfo: _HID=none UID=0
dev.cpu.2.%parent: acpi0
dev.cpu.2.cx_supported: C1/0
dev.cpu.2.cx_lowest: C1
dev.cpu.2.cx_usage: 100.00% last 5000us
dev.cpu.3.%desc: ACPI CPU
dev.cpu.3.%driver: cpu
dev.cpu.3.%location: handle=_PR.P004
dev.cpu.3.%pnpinfo: _HID=none _UID=0
dev.cpu.3.%parent: acpi0
dev.cpu.3.cx_supported: C1/0
dev.cpu.3.cx_lowest: C1
dev.cpu.3.cx_usage: 100.00% last 5000us

Eamon

stephenw10

To use either of those tools you have to install the FreeBSD package properly, so:

As you are running NanoBD first remount the filesystem read-write

[2.0.3-RELEASE][root@pfsense.fire.box]/root(1): /etc/rc.conf_mount_rw

Then add the package. You have to specify the complete path beacsue FreeBSD 8.1 is now quite old

[2.0.3-RELEASE][root@pfsense.fire.box]/root(2): pkg_add -r ftp://ftp-archive.freebsd.org/pub/FreeBSD-Archive/ports/i386/packages-8.1-release/Latest/superiotool.tbz
Fetching ftp://ftp-archive.freebsd.org/pub/FreeBSD-Archive/ports/i386/packages-8.1-release/Latest/superiotool.tbz... Done.

same for flashrom

[2.0.3-RELEASE][root@pfsense.fire.box]/root(3): pkg_add -r ftp://ftp-archive.freebsd.org/pub/FreeBSD-Archive/ports/i386/packages-8.1-release/Latest/flashrom.tbz
Fetching ftp://ftp-archive.freebsd.org/pub/FreeBSD-Archive/ports/i386/packages-8.1-release/Latest/flashrom.tbz... Done.
Fetching ftp://ftp-archive.freebsd.org/pub/FreeBSD-Archive/ports/i386/packages-8.1-release/All/libpci-3.1.7_1.tbz... Done.

Then remount the filesystem read-only again

[2.0.3-RELEASE][root@pfsense.fire.box]/root(4): /etc/rc.conf_mount_ro

Finally issue a rehash to re-index the new files so FreeBSD knows where to find them

[2.0.3-RELEASE][root@pfsense.fire.box]/root(5): rehash

Now you run the tools. :)

After you install the lcdproc-dev package via the pfSense GUI you have to configure the various parameters before it will run and then start the service manually the first time in Status: Services:

Steve

fmertz

@Eams:

isab0@pci0:0:31:0: class=0x060100 card=0x29148086 chip=0x29148086 rev=0x02 hdr=0x00

Yep, confirmed ICH9D0. Dom 0, bus 0, device 31, function 0 is the L(ow)P(in)C(ount) device. We can use it to identify the exact ICH model number.

Eams

I had lcdproc loaded - removed and installed lcdproc-dev - selected WatchGuard Firebox with SDEC (x86only) - see attached pics.

Looks like powerd is doing it's job running the cpu at 330Mhz - fans however haven't slowed down any though :(

Superiotool probe..:
$ superiotool -d
superiotool r
Found ITE IT8718F (id=0x8718, rev=0x4) at 0x2e
Register dump:
idx 20 21 22 23 24 2b
val 87 18 04 10 00 00
def 87 18 01 00 00 00
LDN 0x00 (Floppy)
idx 30 60 61 70 74 f0 f1
val 00 00 00 00 04 00 00
def 00 03 f0 06 02 00 00
LDN 0x01 (COM1)
idx 30 60 61 70 f0 f1 f2 f3
val 00 03 f8 04 00 50 00 7f
def 00 03 f8 04 00 50 00 7f
LDN 0x02 (COM2)
idx 30 60 61 70 f0 f1 f2 f3
val 01 02 f8 03 00 50 00 7f
def 00 02 f8 03 00 50 00 7f
LDN 0x03 (Parallel port)
idx 30 60 61 62 63 70 74 f0
val 01 03 78 00 00 07 04 08
def 00 03 78 07 78 07 03 03
LDN 0x04 (Environment controller)
idx 30 60 61 62 63 70 f0 f1 f2 f3 f4 f5 f6
val 01 0a 10 0a 00 00 80 00 00 00 a0 00 ff
def 00 02 90 02 30 09 00 00 00 00 00 NA NA
LDN 0x05 (Keyboard)
idx 30 60 61 62 63 70 71 f0
val 01 00 60 00 64 01 02 00
def 01 00 60 00 64 01 02 00
LDN 0x06 (Mouse)
idx 30 70 71 f0
val 01 0c 02 00
def 00 0c 02 00
LDN 0x07 (GPIO)
idx 25 26 27 28 29 2a 2c 60 61 62 63 64 65 70 71 72 73 74 b0 b1 b2 b3 b4 b5 b8 b9 ba bb bc bd c0 c1 c2 c3 c4 c5 c8 c9 ca cb cc e0 e1 e2 e3 e4 e5 e6 e7 f0 f1 f2 f3 f4 f5 f6 f7 f8 f9 fa fb fc fd fe ff
val 41 d3 00 00 00 20 1f 00 00 0a 20 0a 30 00 00 00 00 00 00 00 00 00 00 00 40 00 00 00 00 00 40 d3 00 40 00 00 40 d0 00 40 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 bc 00 00 00
def 01 00 00 40 00 00 00 00 00 00 00 00 00 00 00 20 38 00 00 00 00 00 00 00 00 00 00 00 00 00 01 00 00 40 00 00 01 00 00 40 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 NA 00 00 00
LDN 0x0a (Consumer IR)
idx 30 60 61 70 f0
val 00 00 00 00 06
def 00 03 10 0b 00

Hope that is of some use ;D

Haven't managed to get flashrom to run ???

Eamon

IMG_20130517_004538.jpg_thumb

IMG_20130517_005003.jpg_thumb

fmertz

@Eams:

Selected WatchGuard Firebox with SDEC (x86only) - see attached pics.

That was an easy win. Good to see, though. Have you tried the buttons? Best guess, they sort of work, but are not mapped correctly…