TippingPoint X506 Hardware
-
You can't just assign VLANs at random. Assign the sis interface directly.
Steve
I need 2 interfaces before pfsense will proceed, do I assign one generic vlan as WAN and then assign the sis0 directly to LAN? How would you do it?
-
PfSense only requires 1 interface. But yes you could use one real interface and one VLAN interface.
The other possibility is that the default config of the switch is no vlans at all, just like an unmanaged switch.Steve
-
I'm keeping an eye on this thread :)
-
I wonder if this has similar hardware :P
http://www.ebay.ca/itm/HP-Tippingpoint-Core-Controller-48-Port-Gigabit-Switch-/321258224413?pt=US_Network_Switches&hash=item4acc7b7b1d -
Unlikely. You need some serious power for a 48 port gig switch. You're suggesting it might have an x86 backend? Maybe if it has any firewall or routing features. I doubt it though.
Steve
-
You're suggesting it might have an x86 backend?
SteveIts a posibility…
And that's what I'm after :)
-
PfSense only requires 1 interface. But yes you could use one real interface and one VLAN interface.
The other possibility is that the default config of the switch is no vlans at all, just like an unmanaged switch.Steve
Ive now assigned sis0 as LAN and since it asked for WAN first, I just filled in a random vlan name. However, nomatter what cable or port I plug into, none of the ports light up. They dont recognize that a cat5 cable is plugged in.
If it doesnt see that a cat5 cable is plugged in, how is a packet capture going to work? Dont we first have to work through getting sis0 "UP"?
-
Ah, well that makes things a lot more complex. If the default config of the switch is no config at all, everything off, then it needs to be configured before anything will work.
Yes you need to see sis0 as UP before anything else.
Where are you reading this though, at the console I assume. What do you see from 'ifconfig -a'? If it is vlans only at sis0 then an interface set to use no tags or vlan1 might show as down. What does is show for media and status?Steve
-
Im doing everything from the console at this point.
Enter an option: 1 Valid interfaces are: sis0 02:63:c0:d6:7b:7e (up) NatSemi DP8381[56] 10/100BaseTX Do you want to set up VLANs first? If you are not going to use VLANs, or only for optional interfaces, you should say no here and use the webConfigurator to configure VLANs later, if required. Do you want to set up VLANs now [y|n]? y WARNING: all existing VLANs will be cleared if you proceed! Do you want to proceed [y|n]?y VLAN Capable interfaces: sis0 02:63:c0:d6:7b:7e (up) Enter the parent interface name for the new VLAN (or nothing if finished): sis0 Enter the VLAN tag (1-4094): 1 VLAN Capable interfaces: sis0 02:63:c0:d6:7b:7e (up) Enter the parent interface name for the new VLAN (or nothing if finished): VLAN interfaces: sis0_vlan1 VLAN tag 1, parent interface sis0 *NOTE* pfSense requires *AT LEAST* 1 assigned interface(s) to function. If you do not have *AT LEAST* 1 interfaces you CANNOT continue. If you do not have at least 1 *REAL* network interface card(s) or one interface with multiple VLANs then pfSense *WILL NOT* function correctly. If you do not know the names of your interfaces, you may choose to use auto-detection. In that case, disconnect all interfaces now before hitting 'a' to initiate auto detection. Enter the WAN interface name or 'a' for auto-detection: sis0_vlan1 Enter the LAN interface name or 'a' for auto-detection NOTE: this enables full Firewalling/NAT mode. (or nothing if finished): sis0 Enter the Optional 1 interface name or 'a' for auto-detection (or nothing if finished): The interfaces will be assigned as follows: WAN -> sis0_vlan1 LAN -> sis0 Do you want to proceed [y|n]?y Writing configuration...done. One moment while we reload the settings... done! *** Welcome to pfSense 2.1-RELEASE-nanobsd (i386) on pfSense *** WAN (wan) -> sis0_vlan1 -> LAN (lan) -> sis0 -> v4: 10.0.0.169/24 0) Logout (SSH only) 8) Shell 1) Assign Interfaces 9) pfTop 2) Set interface(s) IP address 10) Filter Logs 3) Reset webConfigurator password 11) Restart webConfigurator 4) Reset to factory defaults 12) pfSense Developer Shell 5) Reboot system 13) Upgrade from console 6) Halt system 14) Enable Secure Shell (sshd) 7) Ping host 15) Restore recent configuration Enter an option:[2.1-RELEASE][root@pfSense.localdomain]/root(1): ifconfig -a sis0: flags=8843 <up,broadcast,running,simplex,multicast>metric 0 mtu 1500 options=83808 <vlan_mtu,wol_ucast,wol_mcast,wol_magic,linkstate>ether 02:63:c0:d6:7b:7e inet6 fe80::7422:d7c0:c46:842%sis0 prefixlen 64 scopeid 0x1 inet 10.0.0.169 netmask 0xffffff00 broadcast 10.0.0.255 nd6 options=1 <performnud>media: Ethernet autoselect (none) status: no carrier enc0: flags=0<> metric 0 mtu 1536 pfsync0: flags=0<> metric 0 mtu 1460 syncpeer: 224.0.0.240 maxupd: 128 syncok: 1 pflog0: flags=100 <promisc>metric 0 mtu 33192 lo0: flags=8049 <up,loopback,running,multicast>metric 0 mtu 16384 options=3 <rxcsum,txcsum>inet 127.0.0.1 netmask 0xff000000 inet6 ::1 prefixlen 128 inet6 fe80::1%lo0 prefixlen 64 scopeid 0x5 nd6 options=3 <performnud,accept_rtadv>sis0_vlan100: flags=8843 <up,broadcast,running,simplex,multicast>metric 0 mtu 1500 ether 02:63:c0:d6:7b:7e inet6 fe80::7422:d7c0:c46:842%sis0_vlan100 prefixlen 64 scopeid 0x6 nd6 options=3 <performnud,accept_rtadv>media: Ethernet autoselect (none) status: no carrier vlan: 100 vlanpcp: 0 parent interface: sis0 sis0_vlan200: flags=8843 <up,broadcast,running,simplex,multicast>metric 0 mtu 1500 ether 02:63:c0:d6:7b:7e inet6 fe80::7422:d7c0:c46:842%sis0_vlan200 prefixlen 64 scopeid 0x7 nd6 options=3 <performnud,accept_rtadv>media: Ethernet autoselect (none) status: no carrier vlan: 200 vlanpcp: 0 parent interface: sis0 sis0_vlan300: flags=8843 <up,broadcast,running,simplex,multicast>metric 0 mtu 1500 ether 02:63:c0:d6:7b:7e inet6 fe80::7422:d7c0:c46:842%sis0_vlan300 prefixlen 64 scopeid 0x8 nd6 options=3 <performnud,accept_rtadv>media: Ethernet autoselect (none) status: no carrier vlan: 300 vlanpcp: 0 parent interface: sis0 sis0_vlan1: flags=8843 <up,broadcast,running,simplex,multicast>metric 0 mtu 1500 ether 02:63:c0:d6:7b:7e inet6 fe80::7422:d7c0:c46:842%sis0_vlan1 prefixlen 64 scopeid 0x9 nd6 options=3 <performnud,accept_rtadv>media: Ethernet autoselect (none) status: no carrier vlan: 1 vlanpcp: 0 parent interface: sis0 [2.1-RELEASE][root@pfSense.localdomain]/root(2):</performnud,accept_rtadv></up,broadcast,running,simplex,multicast></performnud,accept_rtadv></up,broadcast,running,simplex,multicast></performnud,accept_rtadv></up,broadcast,running,simplex,multicast></performnud,accept_rtadv></up,broadcast,running,simplex,multicast></performnud,accept_rtadv></rxcsum,txcsum></up,loopback,running,multicast></promisc></performnud></vlan_mtu,wol_ucast,wol_mcast,wol_magic,linkstate></up,broadcast,running,simplex,multicast> -
sis0: flags=8843 <up,broadcast,running,simplex,multicast>metric 0 mtu 1500 options=83808 <vlan_mtu,wol_ucast,wol_mcast,wol_magic,linkstate>ether 02:63:c0:d6:7b:7e inet6 fe80::7422:d7c0:c46:842%sis0 prefixlen 64 scopeid 0x1 inet 10.0.0.169 netmask 0xffffff00 broadcast 10.0.0.255 nd6 options=1 <performnud>media: Ethernet autoselect (none) status: no carrier</performnud></vlan_mtu,wol_ucast,wol_mcast,wol_magic,linkstate></up,broadcast,running,simplex,multicast>Hmm, well that doesn't look good. I would expect that sis0 is always connected to the switch. The switch may have autonegotiation disabled on that port. You could try setting sis0 to 100Mbps FD and see if shows carrier. Though even if auto was disabled it should still fall back to 10Mb HD if a connection is detected. :-\
You might be able to port (if someone else hasn't done it already some roboswitch code from, for example, OpenWRT.
Steve
