FTP Client problem
-
Hi,
unfortunately, the ftp servers to which I have to connect are not managed by me, I use the client part.
I attach image related to the error I have on the ftp client.
The same connection, from the same ftp client to the same ftp server, from a PC that is not behind pfsense works well.
Thanks.
-
Dude how dense can you be?? the ftp.exe in pfsense does NOT support passive... If you want to use active ftp client behind pfsense you need to install the ftp package!!
They might have a passive cmd - IT DOESNT WORK!!! windows ftp.exe ONLY supports active!!!
-
Hi,
so an ftp client that is behind pfsense and needs to access an ftp server that only supports passive mode, will it never work?
did I get it right ?
Thanks. -
No.
Passive FTP will work fine with the client behind pfSense without the proxy package.
Active FTP requires the client proxy package.Since the Windows ftp client apparently only supports active mode you need the client proxy package.
https://www.netgate.com/docs/pfsense/nat/ftp-without-a-proxy.html#client-behind-pfsense
But are you sure those servers don't support encrypted mode? If they do you just switch to that.
Steve
-
So which is it you do not read english, or your trolling... Have been over this multiple times now!!
Please what part is unclear here
Again the ftp client (ftp.exe) in windows only supports ACTIVE... If you want to use active on clients behind pfsense then you need to install that package..
If your clients use passive then no you do not need the package...
And before that how can this be clearer
ms ftp client only supports active mode. If you want to use active mode ftp with client behind pfsense to ftp server outside pfsense you need to install the ftp package and configure it. Its called FTP_Client_Proxy in the packages.
Your ftp.exe command tells the server hey lets do passive - and the server answers back ok, lets do passive - connect here on this port... The problem is the ftp.exe from windows will not do passive... You have to use the ftp package in pfsense to allow for active connections from clients behind pfsense because the firewall needs to open the port back to the client..
-
Hi,
it does not work either in active or passive mode.
I installed the ftp proxy package and I indicated the LAN as an interface to be used (I have not modified any other parameter) but also in this way I always have the same problem.I'm sorry if I did not understand what you told me but I can not understand where I'm wrong.
Thanks. -
If you set 'Log Connections' in the proxy settings do you see firewall log entries for it?
Do you see blocked traffic from the FTP server?
You might try using a different FTP client as a test here such as Filezilla. That will show you exactly what it's doing.
Steve
-
is the checkbox set to move it up the higher on the rules?
Here just tested this
C:\WINDOWS\system32>ftp speedtest.tele2.net Connected to speedtest.tele2.net. 220 (vsFTPd 2.3.5) 200 Always in UTF8 mode. User (speedtest.tele2.net:(none)): anonymous 331 Please specify the password. Password: 230 Login successful. ftp> ls 200 PORT command successful. Consider using PASV. 150 Here comes the directory listing. 1000GB.zip 100GB.zip 100KB.zip 100MB.zip 10GB.zip 10MB.zip 1GB.zip 1KB.zip 1MB.zip 200MB.zip 20MB.zip 2MB.zip 3MB.zip 500MB.zip 50MB.zip 512KB.zip 5MB.zip upload 226 Directory send OK. ftp: 183 bytes received in 0.02Seconds 11.44Kbytes/sec. ftp>active works just fine with windows ftp client behind pfsense..
You can see where its allowed through the firewall with these rules
Jan 30 12:28:54 ► LAN (@0) 90.130.70.73:20 192.168.9.100:55659 TCP:S Jan 30 12:28:54 WAN (@0) 90.130.70.73:20 192.168.9.100:55659 TCP:SHere doing it again with sniff..
Notice the port command sent is my machine rfc1918 IP, the ftp client changes that to my public IP, and if you do the math on the command (217*256)+148 = 55700 which is the port the data channel is sent to..
-
@stephenw10
Trace: CControlSocket::SendNextCommand()
Trace: CFtpLogonOpData::Send() in state 0
Stato: Risoluzione dell'indirizzo IP x.y.eu in corso
Stato: Connessione a x.x.x.x:21...
Stato: Connessione stabilita, in attesa del messaggio di benvenuto...
Trace: CFtpControlSocket::OnReceive()
Risposta: 220 Microsoft FTP Service
Trace: CFtpLogonOpData::ParseResponse() in state 1
Trace: CControlSocket::SendNextCommand()
Trace: CFtpLogonOpData::Send() in state 5
Comando: USER pippo
Trace: CFtpControlSocket::OnReceive()
Risposta: 331 Password required
Trace: CFtpLogonOpData::ParseResponse() in state 5
Trace: CControlSocket::SendNextCommand()
Trace: CFtpLogonOpData::Send() in state 5
Comando: PASS **********
Trace: CFtpControlSocket::OnReceive()
Risposta: 230 User logged in.
Trace: CFtpLogonOpData::ParseResponse() in state 5
Trace: CControlSocket::SendNextCommand()
Trace: CFtpLogonOpData::Send() in state 9
Comando: OPTS UTF8 ON
Trace: CFtpControlSocket::OnReceive()
Risposta: 200 OPTS UTF8 command successful - UTF8 encoding now ON.
Trace: CFtpLogonOpData::ParseResponse() in state 9
Stato: Accesso effettuato
Trace: Measured latency of 5 ms
Trace: CFtpControlSocket::ResetOperation(0)
Trace: CControlSocket::ResetOperation(0)
Trace: CFtpLogonOpData::Reset(0) in state 14 -
@johnpoz I do not work, when I run "ls" I have the error message that I attach
-
I don't see any port or pasv command sent in that log... Just sniff on the wan and lan of pfsense while you doing this so you can validate what is happening... ftp control is in the clear so as you see above you can see exactly what is sent by the client in the control channel. If when you sniff on the wan side you will see the ftp package change your port command to your actual public IP
Is pfsense behind a NAT? Not going to work if behind a NAT..
Is the wan of pfsense on a public IP? Sniff while you do that test of ftp to speedtest.tele2.net
So we can see exactly what is happening.
-
yes, the computer is behind a NAT, it has a private IP address.
-
NO pfsense is its wan a rfc1918 or the is it public?
-
@johnpoz on pfsense I have wan interface e lan interface, on wan interface I have an public IP address.
-
Like I said do a simple sniff.. And you can see exactly what is going on..
Here sniff (diag, packet capture on my wan) you can see my login on port 21... See where the PORT command gets changed to my public IP..
Then here comes the data connection to the port in the the port command
(200*256)+175 = port 51375
-
This post is deleted! -
@johnpoz sorry I do not know how to capture the really useful information, in the figure I sent I deleted the private IP address that is shown in the capture
-
Dude are you hiding a 10.x.x.x address? Why??? They are private and do not route on the internet... That info is useless to anyone knowing what it is.. Its like telling you I live in the US.. or the planet Earth.. Notice how I didn't hide my 192.168.9.100 address ;) You can capture the info right on pfsense.. diagnostic menu packet capture.
Do the capture on your WAN interface so we can validate its getting changed to your public wan IP.. Then just download the capture and open with wireshark.
In wireshark just right click on say the syn of the control channel and say follow stream.
BTW, I am a mod so I can see your deleted post ;) There is ZERO reason to hide 10.0.0.18.. You need to validate that gets changed on your WAN.. This is why you need to do the sniff on the WAN of pfsense to validate your ftp package is working.
here
Then download and open with wireshark
-
@johnpoz here is the log, I hope it contains useful information.
Thanks.
-
So he sent data connect to port 51069, which is correct per the PORT command.. (199*256)+125 but no answer..
Did the package not create the firewall rule? Did it not get placed at the top like I asked before
Did the pfsense forward it, but your client didn't answer? Sniff on the LAN side now when you do the test.. We can see from the sniff that the PORT command was changed to your public IP with that 167.x.x.x
So yeah its very useful information.
What are your firewall rules on your WAN? Are you running packages like Snort or Pfblocker?
