Web GUI
-
Send text or picture?
-
print screen, the best, as I did
-
There it is
-
huhhh....
this shows that you only have one ISP public IP on WAN 1
RFC1918 address is configured on WAN2 (this could easily be one dual -NAT on WAN2?)
and you have a VPN gateway configured as wellthis is not a pure dual-ISP load balance setting with multi -WAN
what does your gateway setting look like?
-
Hi,
Always take in account that 8.8.8.8 was build with on goal in mind : serving DNS requests on it's port 53.
If it has time to do something else - that's how ICMP works - il will reply on ICMP requests.
Then the entire world decided to give 8.8.8.8 all their DNS requests.
All this boils down to : you have to consider that it's maybe not wise to choose a heavenly loaded server as 'ICMP 'test' point.Not receiving an answer on a ping request doesn't break anything **. You might say : the route the ping packet took is over crowded, so it will get ditched immediately.
The dpinger process is counting the returns of a ping. If to many are missing, it will reset your "WAN" connection - this connection might be without any issues, except that further on the route some router decides to throw away a ping packet or two.
I advise you to use/test with another monitor IP ... because if 8.8.8.8 - or the route to it - goes bad, your local connection to the net will really suffer, because dpinger starts to bounce it.
Btw : If you native WAN connection is bad, the traffic that flows through it is also bad : in your case the VPN over the WAN traffic.
** With IPv6 this changes.
-
@Gertjan
the basic problem of the OP is, that with a multi-WAN configuration it is not possible to access the GUI on the second WAN connectionI agree with you about monitor IP:
although it can be seen in my own configuration that I use 1.0.0.1(on the second and VPN gateway) for this purpose, unfortunately the ExpVPN gateway is not pingable
I can't set up VPN GTW monitoring with another gateway - which one?
Plus, CloudFlare has a very fast response time on my location, so I don't spoil my measurement resultssince I also use this for DNS, through the VPN tunnel, so I get the values with a good approximation
any suggestions for external monitor IP?
-
@DaddyGo there it is
-
this doesn't need to be obscured as I have already seen everything from dpinger logs
so, I really can't use what you uploaded (PRTSC)
so, WAN2 gets an internal IP address? (RFC1918), do you get it from another DHCP-capable router on your internal network?
edit: 192.168.80.171 (RFC1918)
-
this doesn't need to be obscured as I have already seen everything from dpinger logs
so, I really can't use what you uploaded (PRTSC)
so, WAN2 gets an internal IP address? (RFC1918), do you get it from another DHCP-capable router on your internal network?
edit: 192.168.80.171 (RFC1918)The policy of this provider is this - the real ip address is looking on the Internet, all requests from it are forwarded to the corresponding address ports 192.168.80.171 - this is the provider subnet
-
Yes, just like a dual -NAT
(what device do you have from your ISP for this configuration)where do you get this IP address?
192.168.80.171 from 192.168.80.1 GTW via DHCP?109.72.249.161 ??? I think this is your public 2 address ISP GTW
what ports are forwarded 109.72.249.161 and it is between 192.168.80.1 - 192.168.80.171what is the GUI access port (on your device)?
it will surely be transmitted across this dual NAT suspicious configuration -
Yes, just like a dual -NAT
(what device do you have from your ISP for this configuration)
where do you get this IP address?
192.168.80.171 from 192.168.80.1 GTW via DHCP?
109.72.249.161 ??? I think this is your public 2 address ISP GTW
what ports are forwarded 109.72.249.161 and it is between 192.168.80.1 - 192.168.80.171
what is the GUI access port (on your device)?
it will surely be transmitted across this dual NAT suspicious configurationI also had a suspicion of NAT
But other ports are forwarded without problems.
The provider claims that all ports are forwarded 1:1, nothing is blocked -
Okay, let's try it
move the GUI port to a good height, such as 50443F.E.:
you know I wouldn't use such an ISP
you still haven't written down your hardwares types and connections methods -
you know I wouldn't use such an ISP
I would also change the provider, but we have no analogues)you still haven't written down your hardwares types and connections methods
From all providers settings come via DHCP. -
you know I wouldn't use such an ISP
I would also change the provider, but we have no analogues)you still haven't written down your hardwares types and connections methods
From all providers settings come via DHCP.And the answer was ?
-
I would also change the provider, but we have no analogues)
From all providers settings come via DHCP. -
if there is no port filtering..... - , you say that 1:1, then something is still missing (NAT-NAT-NAT)
we would expect a drawing from you about the system (in any form, even by hand)
and raise the GUI port to a higher range- I would still pull out the WAN1 cable (if it is possible of course) and see what happens then
-I think you will be surprised what is not working in addition to the GUI yet
the load balancer can hide a lot of things in front of your eyes, if you don't pay attention and you think everything works great on both WANs (Round-robin)
- I would still pull out the WAN1 cable (if it is possible of course) and see what happens then
-
if there is no port filtering..... - , you say that 1:1, then something is still missing (NAT-NAT-NAT)
we would expect a drawing from you about the system (in any form, even by hand)
and raise the GUI port to a higher rangeI would still pull out the WAN1 cable (if it is possible of course) and see what happens then
-I think you will be surprised what is not working in addition to the GUI yetthe load balancer can hide a lot of things in front of your eyes, if you don't pay attention and you think everything works great on both WANs (Round-robin)
-
THX:
-I wonder what tool / device (CPE) produces this?
-do you have access to this tool / device?
-can you change the GUI port?
-what about WAN1 test, can be disconnected and tested
-
-I wonder what tool / device (CPE) produces this?
-do you have access to this tool / device?
-can you change the GUI port?
-what about WAN1 test, can be disconnected and tested- device type unknown
- no access to it
- I will change the port for verification and write the result
- WAN1 will not work in the near future
-
сменить провайдера и мне не помешало бы, но, увы, нет идентичного,
