Web GUI

Ilya.V

Yes, just like a dual -NAT
(what device do you have from your ISP for this configuration)
where do you get this IP address?
192.168.80.171 from 192.168.80.1 GTW via DHCP?
109.72.249.161 ??? I think this is your public 2 address ISP GTW
what ports are forwarded 109.72.249.161 and it is between 192.168.80.1 - 192.168.80.171
what is the GUI access port (on your device)?
it will surely be transmitted across this dual NAT suspicious configuration

I also had a suspicion of NAT
But other ports are forwarded without problems.
The provider claims that all ports are forwarded 1:1, nothing is blocked

DaddyGo

Okay, let's try it
move the GUI port to a good height, such as 50443

F.E.:

you know I wouldn't use such an ISP
you still haven't written down your hardwares types and connections methods

Ilya.V

@DaddyGo said in Web GUI:

you know I wouldn't use such an ISP
I would also change the provider, but we have no analogues)

@DaddyGo said in Web GUI:

you still haven't written down your hardwares types and connections methods
From all providers settings come via DHCP.

Gertjan

@Ilya-V said in Web GUI:

@DaddyGo said in Web GUI:

you know I wouldn't use such an ISP
I would also change the provider, but we have no analogues)

@DaddyGo said in Web GUI:

you still haven't written down your hardwares types and connections methods
From all providers settings come via DHCP.

And the answer was ?

Ilya.V

I would also change the provider, but we have no analogues)
From all providers settings come via DHCP.

DaddyGo

if there is no port filtering..... - , you say that 1:1, then something is still missing (NAT-NAT-NAT)

we would expect a drawing from you about the system (in any form, even by hand)
and raise the GUI port to a higher range

I would still pull out the WAN1 cable (if it is possible of course) and see what happens then
-I think you will be surprised what is not working in addition to the GUI yet

the load balancer can hide a lot of things in front of your eyes, if you don't pay attention and you think everything works great on both WANs (Round-robin)

Ilya.V

@DaddyGo said in Web GUI:

if there is no port filtering..... - , you say that 1:1, then something is still missing (NAT-NAT-NAT)
we would expect a drawing from you about the system (in any form, even by hand)
and raise the GUI port to a higher range

I would still pull out the WAN1 cable (if it is possible of course) and see what happens then
-I think you will be surprised what is not working in addition to the GUI yet

the load balancer can hide a lot of things in front of your eyes, if you don't pay attention and you think everything works great on both WANs (Round-robin)

DaddyGo

THX:

-I wonder what tool / device (CPE) produces this?
-do you have access to this tool / device?
-can you change the GUI port?
-what about WAN1 test, can be disconnected and tested

Ilya.V

@DaddyGo said in Web GUI:

-I wonder what tool / device (CPE) produces this?
-do you have access to this tool / device?
-can you change the GUI port?
-what about WAN1 test, can be disconnected and tested

device type unknown
no access to it
I will change the port for verification and write the result
WAN1 will not work in the near future

valentinius

сменить провайдера и мне не помешало бы, но, увы, нет идентичного,

DaddyGo

@valentinius thanks for your comment, but we are beyond that

valentinius

@DaddyGo Yesh, you are right and i am really glad that you have supported me! Wish we were in front of that(