pfSense nic freeze

microkid

Just ran a stress test for 10 minutes.
stress-ng --metrics --cpu 4 --vm 4 --vm-bytes 2G --io 2

CPU 100%, mem 99%. Rock stable, not a glitch. Still being able to download at 250Mbps.

DaddyGo

yes these mistakes are the worst
like looking for a needle in a haystack

I would otherwise sharpen the test to network transmission....

since the CPU and MEM test is good in the short term, but think about it if it’s a longer term thing
for example, a thermal heat run error and only occurs if the temperature on one of the active elements on the MOBO is higher for a long time

microkid

@DaddyGo Good point. But the load on the device is usually very low. It's just an home router/firewall. CPU is normally <5% and memory around 40. With my usage, I don't expect high temperatures very soon :)

DaddyGo

@microkid

what you are writing about is a relative state of rest
routing does not require power machines

I understand all this and and I know the pfSense resource needs..
I have seen huge pfBlockerNG lists loading with 98% CPU and 4GB RAM usage (on APU 4d4 board)
it was of course an overloaded pfSense box and an unreasonably large list

this can happen when you are not supervising the box and not seeing it

but eventually kills the OP system
it randomly occurs, as your problem

microkid

I understand. However, pfBlockerNG is updating every hour, as are more things. The monitor log does show a little increase on memory usage at that moment, nothing else. Will keep an eye on it.

DaddyGo

@microkid

hard, hard...

it really remains to seize the moment and and you can do any investigation when the incident happens.
for now - because nowhere to find anything (crash report, suspicious logs) you can only wait.

BTW: I don't think that pfSense problem is this...

DaddyGo

@microkid

one more idea:
what about the latest BIOS?
since the ACPI FW code can cause such a stupid situation

microkid

The device is on the lastest bios from 2018. No newer bios was released since then.

DaddyGo

@microkid

this can be a problem (looks like old BIOS)
what do you see after that(?):

dmesg | grep 'error'
dmesg | grep 'Firmware*'

microkid

dmesg|grep 'error'
module_register_init: MOD_LOAD (vesa, 0xffffffff812d9960, 0) error 19
WARNING: /: mount pending error: blocks 48 files 2

dmesg | grep 'Firmware*'
<no output>

DaddyGo

@microkid

áááhhhááá,

Are you on UFS?
why not ZFS?

this can be due to a lot of violent downtime (crash)

the VESA error is fine (it's strong, hihihi), who also has a VGA controller on the MOBO
but it is "WARNING: /: mount pending error: blocks 48 files 2"

https://forums.freebsd.org/threads/mount-pending-error.67573/

read it and then:

https://docs.netgate.com/pfsense/en/latest/hardware/troubleshooting-disk-check-errors-fsck.html
https://www.youtube.com/watch?v=4DKr1Dvan5I

microkid

@DaddyGo said in pfSense nic freeze:

WARNING: /: mount pending error: blocks 48 files 2"

AFAIK, his is expected, as I had to pull the power to reboot the device. So the disk was not clean shutdown.

DaddyGo

@microkid

yes that's okay, I also wrote this too, but
fix the file system before you scan further the box

everything must be ruled out when searching for such an error..

poor disk fragmentation, a typical cause of random crashes

I know you think of the NIC because the LEDs don't flash but like I said it could be part of a process