-
@dennypage Thanks so much for your assistance with this! Unfortunately, the Netgate SG-2100 only has 1 USB port on it so I dont have any options to try a different USB port. I tried renaming to "myups" and its still the same issue.
-
Can you run the following please?
- disable the UPS service
- unplug and re-plug the usb connection
- run the usbconfig command
- re-enable the UPS service
- run the usbconfig command again
Looking to see something similar to this:
[22.01-RELEASE][root@fw.cococafe.com]/root: usbconfig ugen0.1: <0x8086 XHCI root HUB> at usbus0, cfg=0 md=HOST spd=SUPER (5.0Gbps) pwr=SAVE (0mA) ugen0.2: <Tripp Lite Tripp Lite UPS> at usbus0, cfg=0 md=HOST spd=LOW (1.5Mbps) pwr=ON (0mA) [22.01-RELEASE][root@fw.cococafe.com]/root: -
Hi All.
I have been unable to locate any details on whether I can monitor the UPS state via pfSenses built-in SNMP service, if I have NUT installed and working as aspected?
I Guess the question is: Does NUT have any integration/MIBs that needs to be installed, so the built-in SNMP Service can see state and UPS info from NUT?
Love the no fuss of using the official appliances :-)
-
@missionit-tech Were you able to get your UPS working?
-
@keyser said in NUT package:
Does NUT have any integration/MIBs that needs to be installed, so the built-in SNMP Service can see state and UPS info from NUT?
If I understand your question correctly, you are asking if you can monitor the state of a non SNMP based UPS connected to the pfSense system via the SNMP server on pfSense. Assuming so...
This is more an SNMP question than a NUT question. The SNMP server (bsnmp or net-snmp) determines what/how/where something is exposed via SNMP. There is nothing built-in to either SNMP package to support NUT status, however both support extensions that will allow you to do what you want. You will have to configure the integration yourself. Search for "bsnmp-ucd" (bsnmp) or "net-snmp-extend-mib" (net-snmp) for details.
Here is an example integration using net-snmp.
One additional note: The configuration UI for bsnmp does not have any allowance for extensions, so you would have to go out to the filesystem and modify the config file. It might be easier to use the net-snmp package, which does have allowance for extensions in the UI. See the Extended Commands section at the bottom of the Host Information tab.
HTH
-
@dennypage Thank you for the detailed answer.
This is a little above my allowed time to invest in geekery :-)
I was just wondering if perhaps someone had already done that integration :-)
Love the no fuss of using the official appliances :-)
-
@dennypage
I have not made it back to the site yet to test the last troubleshooting steps that you suggested. Sorry for the delay getting back to you on it. Ill keep you posted when I get back onsite. Thanks for checking in. -
-
@dennypage said in NUT package:
@keyser Using librenms by chance? If so, it's pretty easy. The integration script is here. All you have to do is put the script on the local filesystem and add the script in the Extended Commands section for net-snmp...
Unfortunately not. I’m Using Zabbix, and have recently moved away from a Zabbix Agent on my pfSense and instead started using the “pfSense SNMP” template Zabbix has made available.
It works well, allthough a few counters/details are missing compared to rbecelli’s pfSense Active agent template.
-
@keyser You are more determined than I. I gave Zabbix a serious go a while back. It worked well in circumstances where an agent was available. However for SNMP devices, of which I have a large number, it required far too much work for me. I gave up after a couple of weeks.
-
@dennypage said in NUT package:
@keyser You are more determined than I. I gave Zabbix a serious go a while back. It worked well in circumstances where an agent was available. However for SNMP devices, of which I have a large number, it required far too much work for me. I gave up after a couple of weeks.
Well it did take a little learning, But it’s actually rather simple and flexible. One just needs to understand the architecture. -
Hi all, I've noticed a published NUT 2.8.0 package with a lot of improvements.
Development has been more active this year with actually 2.8.1 started.
Is an updated BSD version of this package on the way ?Thanks to let know if someone knows about it.
-
@filecity said in NUT package:
Hi all, I've noticed a published NUT 2.8.0 package with a lot of improvements.
Development has been more active this year with actually 2.8.1 started.
Is an updated BSD version of this package on the way ?It will probably be a few months. 2.8.0 represents 5+ years of changes, all rolled up into a single release. I expect that will take some time to stabilize.
-
D dennypage referenced this topic on
-
So I replaced my tower UPS with a rackmounted APC Smart-UPS that has a Network Management Card. What is the best way to have a central "UPS server"? Should I point NUT (in pfsense) to the APC UPS using the remote snmp driver and make NUT the main server for everything? Or would it be beneficial to make NUT and other clients as slaves and make the APC UPS as a server itself?
-
@kevindd992002 said in NUT package:
So I replaced my tower UPS with a rackmounted APC Smart-UPS that has a Network Management Card. What is the best way to have a central "UPS server"? Should I point NUT (in pfsense) to the APC UPS using the remote snmp driver and make NUT the main server for everything? Or would it be beneficial to make NUT and other clients as slaves and make the APC UPS as a server itself?
I have a Smart-UPS with an NMC2, and individual hosts speaking directly to the UPS via SNMP. I recommend this approach.
Be sure to assign a fixed address for the UPS. If you running the DHCP server on pfSense, I would also recommend enabling the static ARP option for the UPS (for good measure).
-
Hi. So I have this new UPS that has been added to NUT 3 months ago. I've tried nut-2.8.0 on RPi and it works fine. But I really like to have it handled by pfSense. Any changes on package upgrade to 2.8.0 in the near future?
-
@tnowak What is the UPS and how does it physically connect? Have you confirmed that it does not actually work with 2.7?
-
@dennypage That’s Ever Eco Pro CDS AVR 1200. It’s kind of new kid on the block. It uses usbhid-ups driver. I have tried 2.7 on both pfSense and RPi and it does not work. That UPS has been committed to nut driver 2-3 months ago according to GitHub source. It works fine in 2.8.
-
@tnowak I'll take a look
-
D dennypage referenced this topic on
-
@dennypage can you please help? My UPS has Automatic Voltage Regulation. With the summer heat on the power grid I noticed the input voltage goes from 115-118 volts ac so it has been kicking in a lot more. I think I must have adjusted the original setting to auto correct for anything under 119 volts ac during set up on a older version of this package. However the package now I can not find where that setting to adjustment when AVR should run anymore. The battery this week is getting hammered with the local grid. Last month we had a brownout I had never seen one until this year in California. Our fans everything was slow motion. My HiFi system said low voltage on the screen even a couple weeks ago. I am running in older CP1200AVR made by Cyber Power. I can not remember if you could change the UPS settings from inside of my Netgate firewall or not. It restored 100 of the batter charge after the brownout. However is there anyway to adjust AVR settings from inside of NUT? Or am I imagining this?
