[SOLVED] ntopng can't load the page
-
I corrected it, but problem persist, see you new jpg attached on bottom image …
-
Again: https://192.168.1.1:3000
! -
For I do fast I copy and paste only botton jpg, but I tested for both way, http://192.168.1.1:3000 and https://192.168.1.1:3000 don't works, same problem
-
I see. So edit the rule allowing the access and enable logging.
Also enable logging of the default block rule in Status > System Logs > Settings.Then check the firewall logs for entries relating to the access to 192.168.1.1:3000.
-
I enabled logs for the rula and enabled logs of default block rule. No traces for 192.168.1.1 , but yes traces for rest IPs of my LAN. I think no problem of firewall, could be IIS of pfSense is stopped? I unknow I am thinking…. :-\
-
That makes no sense. Since your are able to access the Web GUI at 192.168.1.1 from a PC you should also be able to access 192.168.1.1:3000 as long as there is no other device between the PC and pfSense which block that.
Albeit if ntopng isn't working you must see the access in the firewall logs.
-
Now I have a great problem. I was to advanced configuration and I changed pfSense protocol to HTTP (it was setted in HTTPS). So I closed the browser, but when I try open now http://192.168.1.1 it wait… waut and not load!!!!!!! go by timeout... Also when display timeout automatically it change URL to https://192.168.1.1 :-[
-
The only quick idea I have to this, you can set it back to https in the console interface.
Go through the LAN address setting, set the IP and mask again. At the end of this you will be ask if you want to allow access via https. -
Finally I solved webConfigurator access enter by 8) Shell in console and editig /conf/config.xml , so I have put <protocol>https</protocol> so I restart and it works, by some cause it works only with with https, so I think it is root of the problem ntopng not load , it still persist
-
??? What about squid/squidGuard, maybe they are related to the issue ?
-
I suspect it, but I review configuration and not seen strange thing, I have 2 pfSense in 2 disticts phisical LAN, recently I seen other pfSense in other LAN (distinct phisical location) allow use protocol http so I installed ntopng package and IT WORKS!!!! … so I must solve in first LAN something of configuration I think because there is still the problem persists and I think because not can use http protocol
-
Finally I have gotten it to work! … I does next steps: 1) Reconfigure webgui protocol with http and port 80 (back I not have put 80, only http) ; 2) Restart pfSense and it works! ; 3) I erased package ntopng ; 4) Restart pfSense ; 5) I installed again package ntopng ; 6) Restart pfSense ; 7) All works!!!!! thank you very much for your interest in my problem!
-
Just reboot pfsense after installing and configuring ntopng.
I just installed ntopng 0.8.6_1 on pfsense 2.3.3-RELEASE-p1.
ntopng times out
Restarted the ntopng service - still times out.
Reboot the pfsense server - ntopng now works.
No configuration changes or firewall rules required.
-
ntop still wont work even after restarting pfsense
this is not solvedanyone else having this problem?
using pfsense
2.4.4-RELEASE-p1 -
So you are seeing exactly the same symptoms?
You should update to 2.4.4p2 but that's probably unrelated.
Steve
-
@stephenw10 said in [SOLVED] ntopng can't load the page:
So you are seeing exactly the same symptoms?
You should update to 2.4.4p2 but that's probably unrelated.
Steve
i did update to
2.4.4-RELEASE-p2now and still same problem..i have restarted ntoppng and even pfsense and the server..still no show
https://forum.netgate.com/post/832233 -
Locking this. If you're seeing some problem with ntopng it's clearly unrelated to whatever issues existed in 2016! I have run ntop without issue many times since then. Please open a new thread detailing exactly what you have tried and what is not working.
Steve
