22.05-RELEASE (amd64) Unable to check for updates?

TAC57

@stephenw10 I just rebooted my pfSense SBC and now pfSense says I'm on the latest version, and I see a number of updates in my installed packages. Go figure! :-)

SteveITS

@tac57 TBH that sounds a bit like it was in the process of installing? If you run into further issues it might be an incomplete install if you booted in the middle, meaning a reinstall might be necessary.

To clarify, were you upgrading to 22.05 or from 22.05 to the dev version?

TAC57

@steveits Now in the process of updating pfBlockerNG-devel it's been fetching the pkg for 15 minutes and the red bar above the package reinstallation bar hasn't moved a bit.

I wasn't updating 22.05, it just said it was unable to check.

stephenw10

Hmm, 15mins is far longer than I'd expect for any package. Unless your WAN is very slow.

I would check the system logs if it's still doing it.

TAC57

@stephenw10 I'm having this problem again. This DNS Lookout command times out after 2 minutes with Host "firmware.netgate.com" could not be resolved.

9.9.9.9 No response
149.112.112.112 No response

I'm also getting the Notice:
An error occurred while uploading the encrypted Netgate pfSense Plus configuration to https://acb.netgate.com/save ( Unable to resolve acb.netgate.com )

I am running pfSense 23.05-RELEASE (amd64) on a Zima SBC (4GB RAM), 240GB SSD (zfs), Intel PRO/1000 PT dual port.

stephenw10

What if you query 9.9.9.9 directly like:

steve@steve-MacBookPro:~$ dig +short @9.9.9.9 firmware.netgate.com
208.123.73.209
208.123.73.207

TAC57

@stephenw10 I entered this from the pfsense+ command line and got:

;; communications error to 9.9.9.9#53: timed out
;; communications error to 9.9.9.9#53: timed out
;; communications error to 9.9.9.9#53: timed out
;; no servers could be reached

SteveITS

@TAC57 if you’re forwarding to Quad9 it sounds like that isn’t working…Snort block maybe? Try turning off forwarding or use a different DNS.

TAC57

@SteveITS In System / General Setup / DNS Servers I changed 9.9.9.9 to 1.1.1.1 and ran the command above with @1.1.1.1 and got the following:

;; communications error to 1.1.1.1#53: timed out
;; communications error to 1.1.1.1#53: timed out
;; communications error to 1.1.1.1#53: timed out
;; no servers could be reached

stephenw10

Can you query either of those from a host behind pfSense?

TAC57

@stephenw10
This from my windows command prompt:
Microsoft Windows [Version 10.0.19045.3031]
(c) Microsoft Corporation. All rights reserved.

C:\Users\Tom>ping 9.9.9.9

Pinging 9.9.9.9 with 32 bytes of data:
Reply from 9.9.9.9: bytes=32 time=266ms TTL=57
Reply from 9.9.9.9: bytes=32 time=15ms TTL=57
Reply from 9.9.9.9: bytes=32 time=15ms TTL=57
Reply from 9.9.9.9: bytes=32 time=16ms TTL=57

Ping statistics for 9.9.9.9:
Packets: Sent = 4, Received = 4, Lost = 0 (0% loss),
Approximate round trip times in milli-seconds:
Minimum = 15ms, Maximum = 266ms, Average = 78ms

C:\Users\Tom>ping 1.1.1.1

Pinging 1.1.1.1 with 32 bytes of data:
Reply from 1.1.1.1: bytes=32 time=267ms TTL=57
Reply from 1.1.1.1: bytes=32 time=16ms TTL=57
Reply from 1.1.1.1: bytes=32 time=15ms TTL=57
Reply from 1.1.1.1: bytes=32 time=15ms TTL=57

Ping statistics for 1.1.1.1:
Packets: Sent = 4, Received = 4, Lost = 0 (0% loss),
Approximate round trip times in milli-seconds:
Minimum = 15ms, Maximum = 267ms, Average = 78ms

C:\Users\Tom>ping 8.8.8.8

Pinging 8.8.8.8 with 32 bytes of data:
Reply from 8.8.8.8: bytes=32 time=14ms TTL=115
Reply from 8.8.8.8: bytes=32 time=13ms TTL=115
Reply from 8.8.8.8: bytes=32 time=14ms TTL=115
Reply from 8.8.8.8: bytes=32 time=14ms TTL=115

Ping statistics for 8.8.8.8:
Packets: Sent = 4, Received = 4, Lost = 0 (0% loss),
Approximate round trip times in milli-seconds:
Minimum = 13ms, Maximum = 14ms, Average = 13ms

C:\Users\Tom>ping acb.netgate.com

Pinging acb.netgate.com [208.123.73.212] with 32 bytes of data:
Reply from 208.123.73.212: bytes=32 time=39ms TTL=51
Reply from 208.123.73.212: bytes=32 time=39ms TTL=51
Reply from 208.123.73.212: bytes=32 time=38ms TTL=51
Reply from 208.123.73.212: bytes=32 time=39ms TTL=51

Ping statistics for 208.123.73.212:
Packets: Sent = 4, Received = 4, Lost = 0 (0% loss),
Approximate round trip times in milli-seconds:
Minimum = 38ms, Maximum = 39ms, Average = 38ms

TAC57

@SteveITS I have DNS resolver enabled. What is the easiest way to turn all this off?

And this has to be related:
An error occurred while uploading the encrypted Netgate pfSense Plus configuration to https://acb.netgate.com/save ( Unable to resolve acb.netgate.com ) @ 2023-05-28 16:49:05

stephenw10

Do you have the DNS resolver set to forwarding mode though?

If you do try just unchecking that so it resolves directly.

TAC57

@stephenw10 It was, unchecking made no difference.

stephenw10

Hmm. Just to be clear is that failing to resolve any host? Even when resolving directly?

That sounds like it must be something blocking DNS requests from the firewall. But I expect anything doing that to apply to NAT'd traffic from clients behind it also.

TAC57

@stephenw10 I'm sorry but I don't understand your question. Is there a screenshot you'd like to see or some setting I can change that might solve this issue.

BTW I ran the dig command from a Raspberry Pi on my network:
crites@raspberrypi:~ $ dig +short @9.9.9.9 firmware.netgate.com
208.123.73.207
208.123.73.209

crites@raspberrypi:~ $ dig +short @9.9.9.9 acb.netgate.com
208.123.73.212

I have a basic homelab setup with some desktop computer, TrueNAS server running Plex, and some IOT stuff.

SteveITS

@TAC57 You’ve posted DNS to third party servers works from devices on LAN but not pfSense. Which implies something is blocking it. Can you post your LAN rules and any floating rules, and routes (diagnostics menu)?

stephenw10

I meant does Diag > DNS Lookup fail for any host or just firmware.netgate.com?

Are you running Snort or Suricata?

TAC57

@stephenw10 Before rebooting I'd get the Unable to check for updates and DNS Lookup would not report anything from any host. On rebooting pfsense it now reports on the latest version. And DNS Lookup does report back (see below) and it reports back from google.com

I am running Snort.

TAC57

@SteveITS I'm not running any floating rules. Can DM you my routes?

LAN rules: