WAN periodically Rebooting
-
@VioletDragon said in WAN periodically Rebooting:
Thought G Fast was killed off ?
It was. At least it's no longer being rolled out. But they didn't remove it from exchanges/cabinets so you can still get it if your line is enabled for it now.
-
@VioletDragon said in WAN periodically Rebooting:
that what you see there is bad caps on the Power Supply.
I thankyou for you comments,..
but failed Caps?.. I question,.. I am getting 4mv of ripple pp, on the 12v rail across a 15000uf electrolytic capacitor.. where the spikes are the switching spikes are noise from the SMPS,.. (these maybe removed with some fast ceramic caps),.. but this supply will then be taken by each device, in this case the modem, passed ( I assume ) through some more regulation circuitry down to an operating voltage of 5v and 3.3v. each rail will then have its own smoothing to ensure reliable operation...
(Also,.. going in back in time,.. 6months,.. the WAN would stay connected for weeks without dropping,.. this is a much improved supply since then)
So the 4mV on the 12v supply IMHO is of little consequence,.. in the overall power supply picture.. -
@diyhouse
Hi Steve,.. just installed my new Draytek 166 modem...
All seems fine,.. albeit I am only getting a download speed of 25MBps... and 10MBps Up, not sure,.. but thinking this is ADSL2 speed,.. is ADSL2+ what I need... ? -
@diyhouse said in WAN periodically Rebooting:
@diyhouse
Hi Steve,.. just installed my new Draytek 166 modem...
All seems fine,.. albeit I am only getting a download speed of 25MBps... and 10MBps Up, not sure,.. but thinking this is ADSL2 speed,.. is ADSL2+ what I need... ?No. VDSL is what you want, ADSL is slow. I would recommend tweaking MTU & MSS on pfsense.
Regards
-
@VioletDragon Phew,.. Thanks,.. have done some more digging around in the modem configs...
1st I am running in "modem/ Bridge mode",.. as opposed to "Router mode"
Looking into the diagnostics..
I am running type: VDSL2
Also the dashboard shows Ports 1 and 2 connected,.. ( I have a simple laptop connected to one port ) but the WAN is not connected,.. even though I have internet access.. and the time is not being set on the modem,..
Am I missing/messing something up in the config..?
If I were to tweak MTU and MSS,.. what sort of values should I use..
Edit: modem has MTU setting of 1520Many tx
-
@diyhouse said in WAN periodically Rebooting:
but the WAN is not connected,.
That's strange.
You talk about the bridge device, right, the 'modem' ?@diyhouse said in WAN periodically Rebooting:
even though I have internet access..
Things don't get any better.
@diyhouse said in WAN periodically Rebooting:
and the time is not being set on the modem
Ah ... finally, something normal. The modem couldn't reach the (a) 'ntp' server, like 'time.nist.gov' or whatever your ISP proposes. Something is wrong.
@diyhouse said in WAN periodically Rebooting:
MTU setting of 1520
I wouldn't have picked that setting, and that value, to try to break my connection's throughput, but this won't you do any good.
If ISP settings don't state, expressly otherwise, apply this :As you can see, lower (then 1500) values can or should be used, under 'circumstances' ... but higher ???!
-
@diyhouse Had to swap back to 'openreach' modem, as Draytek was reconnecting every 5 mins... going from bad to worse comes to mind....
rechecked WAN speed,. and Openreach modem is now down to 25MBps... etc...
Before I swapped out modem looked at line stats,..
and I think that tells a story... its trying to get to 75Mbps,.. but falling back to 25Mbps...I think the 'line' is dying.... what do you guys think... time to call BT
-
Yup could well be a line issue. Though it could also be the line-rate tuning that Openreach does. If you disconnect the line too many times the upstream hardware will de-rate the line until it becomes stable. That can take a while to reset.
-
Just out of interest. What wall socket are you using? Are you using the old wall socket with a Filter ? Or the MK4?
Regards
-
@VioletDragon said in WAN periodically Rebooting:
What wall socket are you using?
I believe I am still using and 'old' wall socket,.. it was installed 3 or 4 yrs ago,..
I have heard spoken to a BT Openreach person,.. and he was saying that I don't need a filter any more as the PSTN stuff has been switched off...
Is this true? -
@stephenw10 Current network speed is of the 24Mbps down 9Mbps Up....
-
@diyhouse Depends on the Faceplate / Master Socket. You don't need the filter if you are using the MK4 Master Socket.
I have replaced a ton of the old type wall sockets for clients as they are not good enough for VDSL, the filters are built into the MK4. I recommend looking into replacing the old Master Sockets with the new MK4. then use a RJ45 to RJ12 cabling is a lot better than the flat BT Spec DSL cable.
Going with the new faceplate will help out a lot with poor speeds and WAN dropping out.
New Faceplate,
Old wallsocket,
Regards
-
@VioletDragon
Yep this is my config, socket wise
So Old config then...
-
@diyhouse Yep I would look at replacing the socket as at that is a more modern faceplate you can just replace the faceplate for the MK4 then run a Ethernet cable with a RJ45 to RJ12. I need to make some more. I use Cat6a then just crimp them.
In some cases BT won't replace them if they send BT guys out but it's a 3rd party working on behalf of BT then they will. You can buy the faceplate off ebay with the backbox for cheap.
Regards
-
Yup no face plate leaves you open to some hidden extension connected without a filter. Possibly.
Also most of those filters might be rated for ADSL only.
-
@stephenw10 Yeah I don't understand why BT don't replace them when customers upgrade to VDSL, I guess they just want a easy life.
Regards
-
Just to be clear you wouldn't need to replace the master socket itself there. Just the faceplate on the front that has the filter in it. If you don't have a bunch or hardwired extensions it's pretty easy.
-
@stephenw10
Ah yes,.. for me no hidden extensions,.. and complete socket assembly available on ebay for £7.00
thanks guys... -
@diyhouse You can also buy DSL cables which have RJ45 to RJ12 on eBay too. I would post a link but not sure if you are allowed.
Good luck,
Regards.
-
Hmm, you mean RJ12 or RJ11? Also I'm not sure where you would use that. The normal xDSL connection uses a cable that has RJ11 at both ends to connect between the modem and faceplate. Even if it has an RJ45 socket you can still use an RJ11 plug in it.
