Realtek 8111B



  • OK, every now and then when the box gets rebooted it wont recognize this nic, i then reboot and then it boots up normally.
    besides dont use realtek use intel…is there anything that could be done?

    re0: <realtek 8168="" 8168b="" 8168c="" 8168cp="" 8168d="" 8111b="" 8111c="" 8111cp="" pcie="" gigabit="" ethernet="">port 0xce00-0xceff mem 0xefcff000-0xefcfffff irq 16 at device 0.0 on pci4
    re0: Using 1 MSI messages
    re0: Chip rev. 0x38000000
    re0: MAC rev. 0x00000000
    miibus1: <mii bus="">on re0
    rgephy0: <rtl8169s 8110s="" 8211b="" media="" interface="">PHY 1 on miibus1
    rgephy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto
    re0: Ethernet address: 00:e0:4d:91:69:20
    re0: [FILTER]</rtl8169s></mii></realtek>



  • What version of pfSense are you using?  Is that interface built into the motherboard?



  • Can you supply the startup output when the system fails to recognise your NIC?



  • its onboard:
    biostar GF7100P-M7S
    http://www.biostar-usa.com/app/en-us/mb/content.php?S_ID=312

    1.2.3 release

    when it doesnt recognize it, it does the standard interface mismatch and presents one with a list of available interfaces to choose from (same prompt that you get when booting up for the first time)



  • @wallabybob:

    Can you supply the startup output when the system fails to recognise your NIC?



  • you mean like dmesg?
    I just reboot it(when it fails to recognize it) and then it recognizes it and boots up fine.



  • @XIII:

    you mean like dmesg?

    Yes.

    @XIII:

    I just reboot it(when it fails to recognize it) and then it recognizes it and boots up fine.

    I presume you reported this because you would like the behaviour to change. Its possible the dmesg (startup) output will contain some clue as to why the NIC is not recognised and that clue might lead to a fix. At the moment there is very little information to work with.



  • ok, will do



  • ok, here it is:
    this is when it doesn't recognize the realek:

    
    $ dmesg
    Copyright (c) 1992-2009 The FreeBSD Project.
    Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
    	The Regents of the University of California. All rights reserved.
    FreeBSD is a registered trademark of The FreeBSD Foundation.
    FreeBSD 7.2-RELEASE-p5 #0: Sun Dec  6 23:20:31 EST 2009
        sullrich@FreeBSD_7.2_pfSense_1.2.3_snaps.pfsense.org:/usr/obj.pfSense/usr/pfSensesrc/src/sys/pfSense_SMP.7
    Timecounter "i8254" frequency 1193182 Hz quality 0
    CPU: Intel(R) Pentium(R) D  CPU 2.66GHz (2666.68-MHz 686-class CPU)
      Origin = "GenuineIntel"  Id = 0xf47  Stepping = 7
      Features=0xbfebfbff <fpu,vme,de,pse,tsc,msr,pae,mce,cx8,apic,sep,mtrr,pge,mca,cmov,pat,pse36,clflush,dts,acpi,mmx,fxsr,sse,sse2,ss,htt,tm,pbe>Features2=0x651d <sse3,dtes64,mon,ds_cpl,tm2,cnxt-id,cx16,xtpr>AMD Features=0x20100000 <nx,lm>AMD Features2=0x1 <lahf>Cores per package: 2
    real memory  = 1071579136 (1021 MB)
    avail memory = 1018007552 (970 MB)
    ACPI APIC Table: <nvidia nvdaacpi="">
    FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs
     cpu0 (BSP): APIC ID:  0
     cpu1 (AP): APIC ID:  1
    ACPI Warning (tbfadt-0505): Optional field "Pm2ControlBlock" has zero address or length:        0       0/1 [20070320]
    ioapic0: Changing APIC ID to 4
    ioapic0 <version 1.1=""> irqs 0-23 on motherboard
    wlan: mac acl policy registered
    kbd1 at kbdmux0
    cryptosoft0: <software crypto=""> on motherboard
    padlock0: No ACE support.
    acpi0: <nvidia nvdaacpi=""> on motherboard
    acpi0: [ITHREAD]
    acpi0: Power Button (fixed)
    acpi0: reservation of 100000, 3fdf0000 (3) failed
    acpi0: reservation of 0, a0000 (3) failed
    Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
    acpi_timer0: <24-bit timer at 3.579545MHz> port 0x1008-0x100b on acpi0
    acpi_hpet0: <high precision="" event="" timer=""> iomem 0xfeff0000-0xfeff03ff on acpi0
    Timecounter "HPET" frequency 25000000 Hz quality 900
    acpi_button0: <power button=""> on acpi0
    pcib0: <acpi host-pci="" bridge=""> port 0xcf8-0xcff on acpi0
    pci0: <acpi pci="" bus=""> on pcib0
    pci0: <memory, ram=""> at device 0.1 (no driver attached)
    pci0: <memory, ram=""> at device 1.0 (no driver attached)
    pci0: <memory, ram=""> at device 1.1 (no driver attached)
    pci0: <memory, ram=""> at device 1.2 (no driver attached)
    pci0: <memory, ram=""> at device 1.3 (no driver attached)
    pci0: <memory, ram=""> at device 1.4 (no driver attached)
    pci0: <memory, ram=""> at device 1.5 (no driver attached)
    pci0: <memory, ram=""> at device 1.6 (no driver attached)
    pci0: <memory, ram=""> at device 2.0 (no driver attached)
    isab0: <pci-isa bridge=""> at device 3.0 on pci0
    isa0: <isa bus=""> on isab0
    pci0: <serial bus,="" smbus=""> at device 3.1 (no driver attached)
    pci0: <memory, ram=""> at device 3.2 (no driver attached)
    pci0: <memory, ram=""> at device 3.4 (no driver attached)
    ohci0: <ohci (generic)="" usb="" controller=""> mem 0xeffff000-0xefffffff irq 21 at device 4.0 on pci0
    ohci0: [GIANT-LOCKED]
    ohci0: [ITHREAD]
    usb0: OHCI version 1.0, legacy support
    usb0: SMM does not respond, resetting
    usb0: <ohci (generic)="" usb="" controller=""> on ohci0
    usb0: USB revision 1.0
    uhub0: <nvidia 1="" 9="" ohci="" root="" hub,="" class="" 0,="" rev="" 1.00="" 1.00,="" addr=""> on usb0
    uhub0: 10 ports with 10 removable, self powered
    ehci0: <ehci (generic)="" usb="" 2.0="" controller=""> mem 0xefffe000-0xefffe0ff irq 22 at device 4.1 on pci0
    ehci0: [GIANT-LOCKED]
    ehci0: [ITHREAD]
    usb1: EHCI version 1.0
    usb1: companion controller, 10 ports each: usb0
    usb1: <ehci (generic)="" usb="" 2.0="" controller=""> on ehci0
    usb1: USB revision 2.0
    uhub1: <nvidia 1="" 9="" ehci="" root="" hub,="" class="" 0,="" rev="" 2.00="" 1.00,="" addr=""> on usb1
    uhub1: 10 ports with 10 removable, self powered
    atapci0: <nvidia nforce="" mcp73="" udma133="" controller=""> port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xfc00-0xfc0f at device 8.0 on pci0
    ata0: <ata 0="" channel=""> on atapci0
    ata0: [ITHREAD]
    ata1: <ata 1="" channel=""> on atapci0
    ata1: [ITHREAD]
    pcib1: <acpi pci-pci="" bridge=""> at device 10.0 on pci0
    pci1: <acpi pci="" bus=""> on pcib1
    sis0: <natsemi 10="" dp8381[56]="" 100basetx=""> port 0xbe00-0xbeff mem 0xefaff000-0xefafffff irq 18 at device 6.0 on pci1
    sis0: Silicon Revision: DP83815D
    miibus0: <mii bus=""> on sis0
    nsphyter0: <dp83815 10="" 100="" media="" interface=""> PHY 0 on miibus0
    nsphyter0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
    sis0: Ethernet address: 00:02:e3:0a:b2:02
    sis0: [ITHREAD]
    ath0: <atheros 5212=""> mem 0xefae0000-0xefaeffff irq 19 at device 7.0 on pci1
    ath0: [ITHREAD]
    ath0: WARNING: using obsoleted if_watchdog interface
    ath0: Ethernet address: 00:1b:2f:2c:b0:75
    ath0: mac 7.9 phy 4.5 radio 5.6
    pcib2: <acpi pci-pci="" bridge=""> at device 11.0 on pci0
    pci2: <acpi pci="" bus=""> on pcib2
    pcib3: <acpi pci-pci="" bridge=""> at device 12.0 on pci0
    pci3: <acpi pci="" bus=""> on pcib3
    pcib4: <acpi pci-pci="" bridge=""> at device 13.0 on pci0
    pci4: <acpi pci="" bus=""> on pcib4
    re0: <realtek 8168="" 8168b="" 8168c="" 8168cp="" 8168d="" 8111b="" 8111c="" 8111cp="" pcie="" gigabit="" ethernet=""> port 0xce00-0xceff mem 0xefcff000-0xefcfffff irq 16 at device 0.0 on pci4
    re0: Using 1 MSI messages
    re0: Chip rev. 0x38000000
    re0: MAC rev. 0x00000000
    miibus1: <mii bus=""> on re0
    rgephy0: <rtl8169s 8110s="" 8211b="" media="" interface=""> PHY 1 on miibus1
    rgephy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto
    re0: Ethernet address: 00:e0:4d:62:31:01
    re0: [FILTER]
    vgapci0: <vga-compatible display=""> mem 0xed000000-0xedffffff,0xd0000000-0xdfffffff,0xee000000-0xeeffffff irq 23 at device 16.0 on pci0
    acpi_tz0: <thermal zone=""> on acpi0
    speaker0: <pc speaker=""> port 0x61 on acpi0
    sio0: <16550A-compatible COM port> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0
    sio0: type 16550A
    sio0: [FILTER]
    cpu0: <acpi cpu=""> on acpi0
    p4tcc0: <cpu frequency="" thermal="" control=""> on cpu0
    cpu1: <acpi cpu=""> on acpi0
    p4tcc1: <cpu frequency="" thermal="" control=""> on cpu1
    pmtimer0 on isa0
    orm0: <isa option="" rom=""> at iomem 0xd0000-0xd3fff pnpid ORM0000 on isa0
    atkbdc0: <keyboard controller="" (i8042)=""> at port 0x60,0x64 on isa0
    atkbd0: <at keyboard=""> irq 1 on atkbdc0
    kbd0 at atkbd0
    atkbd0: [GIANT-LOCKED]
    atkbd0: [ITHREAD]
    sc0: <system console=""> at flags 0x100 on isa0
    sc0: VGA <16 virtual consoles, flags=0x300>
    sio1: configured irq 3 not in bitmap of probed irqs 0
    sio1: port may not be enabled
    vga0: <generic isa="" vga=""> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
    ugen0: <american 0="" 2="" 1000="" power="" conversion="" back-ups="" rs="" fw:7.g3="" .d="" usb="" fw:g3,="" class="" 0,="" rev="" 1.10="" 1.06,="" addr=""> on uhub0
    Timecounters tick every 1.000 msec
    IPsec: Initialized Security Association Processing.
    acd0: CDROM <compaq cd-rom="" sc-148e="" b902=""> at ata0-master PIO4
    ad1: 38166MB <seagate st340019ace="" 9.51=""> at ata0-slave UDMA100
    SMP: AP CPU #1 Launched!
    Trying to mount root from ufs:/dev/ad1s1a
    sis0: Applying short cable fix (reg=f5)
    sis0: Applying short cable fix (reg=eb)
    sis0: Applying short cable fix (reg=eb)
    bridge0: Ethernet address: e6:c2:7b:50:8e:fd
    sis0: Applying short cable fix (reg=ea)
    sis0: Applying short cable fix (reg=eb)
    pflog0: promiscuous mode enabled
    re0: link state changed to UP
    ath0: stuck beacon; resetting (bmiss count 4)
    re0: promiscuous mode enabled
    re0: promiscuous mode disabled
    re0: promiscuous mode enabled
    pflog0: promiscuous mode disabled
    Waiting (max 60 seconds) for system process `vnlru' to stop...done
    Waiting (max 60 seconds) for system process `bufdaemon' to stop...done
    Waiting (max 60 seconds) for system process `syncer' to stop...
    Syncing disks, vnodes remaining...0 done
    All buffers synced.
    Copyright (c) 1992-2009 The FreeBSD Project.
    Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
    	The Regents of the University of California. All rights reserved.
    FreeBSD is a registered trademark of The FreeBSD Foundation.
    FreeBSD 7.2-RELEASE-p5 #0: Sun Dec  6 23:20:31 EST 2009
        sullrich@FreeBSD_7.2_pfSense_1.2.3_snaps.pfsense.org:/usr/obj.pfSense/usr/pfSensesrc/src/sys/pfSense_SMP.7
    Timecounter "i8254" frequency 1193182 Hz quality 0
    CPU: Intel(R) Pentium(R) D  CPU 2.66GHz (2666.69-MHz 686-class CPU)
      Origin = "GenuineIntel"  Id = 0xf47  Stepping = 7
      Features=0xbfebfbff <fpu,vme,de,pse,tsc,msr,pae,mce,cx8,apic,sep,mtrr,pge,mca,cmov,pat,pse36,clflush,dts,acpi,mmx,fxsr,sse,sse2,ss,htt,tm,pbe>Features2=0x651d <sse3,dtes64,mon,ds_cpl,tm2,cnxt-id,cx16,xtpr>AMD Features=0x20100000 <nx,lm>AMD Features2=0x1 <lahf>Cores per package: 2
    real memory  = 1071579136 (1021 MB)
    avail memory = 1018007552 (970 MB)
    ACPI APIC Table: <nvidia nvdaacpi="">
    FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs
     cpu0 (BSP): APIC ID:  0
     cpu1 (AP): APIC ID:  1
    ACPI Warning (tbfadt-0505): Optional field "Pm2ControlBlock" has zero address or length:        0       0/1 [20070320]
    ioapic0: Changing APIC ID to 4
    ioapic0 <version 1.1=""> irqs 0-23 on motherboard
    wlan: mac acl policy registered
    kbd1 at kbdmux0
    cryptosoft0: <software crypto=""> on motherboard
    padlock0: No ACE support.
    acpi0: <nvidia nvdaacpi=""> on motherboard
    acpi0: [ITHREAD]
    acpi0: Power Button (fixed)
    acpi0: reservation of 100000, 3fdf0000 (3) failed
    acpi0: reservation of 0, a0000 (3) failed
    Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
    acpi_timer0: <24-bit timer at 3.579545MHz> port 0x1008-0x100b on acpi0
    acpi_hpet0: <high precision="" event="" timer=""> iomem 0xfeff0000-0xfeff03ff on acpi0
    Timecounter "HPET" frequency 25000000 Hz quality 900
    acpi_button0: <power button=""> on acpi0
    pcib0: <acpi host-pci="" bridge=""> port 0xcf8-0xcff on acpi0
    pci0: <acpi pci="" bus=""> on pcib0
    pci0: <memory, ram=""> at device 0.1 (no driver attached)
    pci0: <memory, ram=""> at device 1.0 (no driver attached)
    pci0: <memory, ram=""> at device 1.1 (no driver attached)
    pci0: <memory, ram=""> at device 1.2 (no driver attached)
    pci0: <memory, ram=""> at device 1.3 (no driver attached)
    pci0: <memory, ram=""> at device 1.4 (no driver attached)
    pci0: <memory, ram=""> at device 1.5 (no driver attached)
    pci0: <memory, ram=""> at device 1.6 (no driver attached)
    pci0: <memory, ram=""> at device 2.0 (no driver attached)
    isab0: <pci-isa bridge=""> at device 3.0 on pci0
    isa0: <isa bus=""> on isab0
    pci0: <serial bus,="" smbus=""> at device 3.1 (no driver attached)
    pci0: <memory, ram=""> at device 3.2 (no driver attached)
    pci0: <memory, ram=""> at device 3.4 (no driver attached)
    ohci0: <ohci (generic)="" usb="" controller=""> mem 0xeffff000-0xefffffff irq 21 at device 4.0 on pci0
    ohci0: [GIANT-LOCKED]
    ohci0: [ITHREAD]
    usb0: OHCI version 1.0, legacy support
    usb0: SMM does not respond, resetting
    usb0: <ohci (generic)="" usb="" controller=""> on ohci0
    usb0: USB revision 1.0
    uhub0: <nvidia 1="" 9="" ohci="" root="" hub,="" class="" 0,="" rev="" 1.00="" 1.00,="" addr=""> on usb0
    uhub0: 10 ports with 10 removable, self powered
    ehci0: <ehci (generic)="" usb="" 2.0="" controller=""> mem 0xefffe000-0xefffe0ff irq 22 at device 4.1 on pci0
    ehci0: [GIANT-LOCKED]
    ehci0: [ITHREAD]
    usb1: EHCI version 1.0
    usb1: companion controller, 10 ports each: usb0
    usb1: <ehci (generic)="" usb="" 2.0="" controller=""> on ehci0
    usb1: USB revision 2.0
    uhub1: <nvidia 1="" 9="" ehci="" root="" hub,="" class="" 0,="" rev="" 2.00="" 1.00,="" addr=""> on usb1
    uhub1: 10 ports with 10 removable, self powered
    atapci0: <nvidia nforce="" mcp73="" udma133="" controller=""> port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xfc00-0xfc0f at device 8.0 on pci0
    ata0: <ata 0="" channel=""> on atapci0
    ata0: [ITHREAD]
    ata1: <ata 1="" channel=""> on atapci0
    ata1: [ITHREAD]
    pcib1: <acpi pci-pci="" bridge=""> at device 10.0 on pci0
    pci1: <acpi pci="" bus=""> on pcib1
    sis0: <natsemi 10="" dp8381[56]="" 100basetx=""> port 0xbe00-0xbeff mem 0xefaff000-0xefafffff irq 18 at device 6.0 on pci1
    sis0: Silicon Revision: DP83815D
    miibus0: <mii bus=""> on sis0
    nsphyter0: <dp83815 10="" 100="" media="" interface=""> PHY 0 on miibus0
    nsphyter0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
    sis0: Ethernet address: 00:02:e3:0a:b2:02
    sis0: [ITHREAD]
    ath0: <atheros 5212=""> mem 0xefae0000-0xefaeffff irq 19 at device 7.0 on pci1
    ath0: [ITHREAD]
    ath0: WARNING: using obsoleted if_watchdog interface
    ath0: Ethernet address: 00:1b:2f:2c:b0:75
    ath0: mac 7.9 phy 4.5 radio 5.6
    pcib2: <acpi pci-pci="" bridge=""> at device 11.0 on pci0
    pci2: <acpi pci="" bus=""> on pcib2
    pcib3: <acpi pci-pci="" bridge=""> at device 12.0 on pci0
    pci3: <acpi pci="" bus=""> on pcib3
    pcib4: <acpi pci-pci="" bridge=""> at device 13.0 on pci0
    pci4: <acpi pci="" bus=""> on pcib4
    vgapci0: <vga-compatible display=""> mem 0xed000000-0xedffffff,0xd0000000-0xdfffffff,0xee000000-0xeeffffff irq 23 at device 16.0 on pci0
    acpi_tz0: <thermal zone=""> on acpi0
    speaker0: <pc speaker=""> port 0x61 on acpi0
    sio0: <16550A-compatible COM port> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0
    sio0: type 16550A
    sio0: [FILTER]
    atkbdc0: <keyboard controller="" (i8042)=""> port 0x60,0x64 irq 1 on acpi0
    atkbd0: <at keyboard=""> irq 1 on atkbdc0
    kbd0 at atkbd0
    atkbd0: [GIANT-LOCKED]
    atkbd0: [ITHREAD]
    cpu0: <acpi cpu=""> on acpi0
    p4tcc0: <cpu frequency="" thermal="" control=""> on cpu0
    cpu1: <acpi cpu=""> on acpi0
    p4tcc1: <cpu frequency="" thermal="" control=""> on cpu1
    pmtimer0 on isa0
    orm0: <isa option="" rom=""> at iomem 0xd0000-0xd3fff pnpid ORM0000 on isa0
    sc0: <system console=""> at flags 0x100 on isa0
    sc0: VGA <16 virtual consoles, flags=0x300>
    sio1: configured irq 3 not in bitmap of probed irqs 0
    sio1: port may not be enabled
    vga0: <generic isa="" vga=""> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
    ugen0: <american 0="" 2="" 1000="" power="" conversion="" back-ups="" rs="" fw:7.g3="" .d="" usb="" fw:g3,="" class="" 0,="" rev="" 1.10="" 1.06,="" addr=""> on uhub0
    Timecounters tick every 1.000 msec
    IPsec: Initialized Security Association Processing.
    acd0: CDROM <compaq cd-rom="" sc-148e="" b902=""> at ata0-master PIO4
    ad1: 38166MB <seagate st340019ace="" 9.51=""> at ata0-slave UDMA100
    SMP: AP CPU #1 Launched!
    Trying to mount root from ufs:/dev/ad1s1a
    sis0: Applying short cable fix (reg=f5)
    sis0: Applying short cable fix (reg=ea)
    sis0: Applying short cable fix (reg=ea)
    pflog0: promiscuous mode enabled</seagate></compaq></american></generic></system></isa></cpu></acpi></cpu></acpi></at></keyboard></pc></thermal></vga-compatible></acpi></acpi></acpi></acpi></acpi></acpi></atheros></dp83815></mii></natsemi></acpi></acpi></ata></ata></nvidia></nvidia></ehci></ehci></nvidia></ohci></ohci></memory,></memory,></serial></isa></pci-isa></memory,></memory,></memory,></memory,></memory,></memory,></memory,></memory,></memory,></acpi></acpi></power></high></nvidia></software></version></nvidia></lahf></nx,lm></sse3,dtes64,mon,ds_cpl,tm2,cnxt-id,cx16,xtpr></fpu,vme,de,pse,tsc,msr,pae,mce,cx8,apic,sep,mtrr,pge,mca,cmov,pat,pse36,clflush,dts,acpi,mmx,fxsr,sse,sse2,ss,htt,tm,pbe></seagate></compaq></american></generic></system></at></keyboard></isa></cpu></acpi></cpu></acpi></pc></thermal></vga-compatible></rtl8169s></mii></realtek></acpi></acpi></acpi></acpi></acpi></acpi></atheros></dp83815></mii></natsemi></acpi></acpi></ata></ata></nvidia></nvidia></ehci></ehci></nvidia></ohci></ohci></memory,></memory,></serial></isa></pci-isa></memory,></memory,></memory,></memory,></memory,></memory,></memory,></memory,></memory,></acpi></acpi></power></high></nvidia></software></version></nvidia></lahf></nx,lm></sse3,dtes64,mon,ds_cpl,tm2,cnxt-id,cx16,xtpr></fpu,vme,de,pse,tsc,msr,pae,mce,cx8,apic,sep,mtrr,pge,mca,cmov,pat,pse36,clflush,dts,acpi,mmx,fxsr,sse,sse2,ss,htt,tm,pbe>
    

    and this is when it does

    $ dmesg
    Copyright (c) 1992-2009 The FreeBSD Project.
    Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
    	The Regents of the University of California. All rights reserved.
    FreeBSD is a registered trademark of The FreeBSD Foundation.
    FreeBSD 7.2-RELEASE-p5 #0: Sun Dec  6 23:20:31 EST 2009
        sullrich@FreeBSD_7.2_pfSense_1.2.3_snaps.pfsense.org:/usr/obj.pfSense/usr/pfSensesrc/src/sys/pfSense_SMP.7
    Timecounter "i8254" frequency 1193182 Hz quality 0
    CPU: Intel(R) Pentium(R) D  CPU 2.66GHz (2666.68-MHz 686-class CPU)
      Origin = "GenuineIntel"  Id = 0xf47  Stepping = 7
      Features=0xbfebfbff <fpu,vme,de,pse,tsc,msr,pae,mce,cx8,apic,sep,mtrr,pge,mca,cmov,pat,pse36,clflush,dts,acpi,mmx,fxsr,sse,sse2,ss,htt,tm,pbe>Features2=0x651d <sse3,dtes64,mon,ds_cpl,tm2,cnxt-id,cx16,xtpr>AMD Features=0x20100000 <nx,lm>AMD Features2=0x1 <lahf>Cores per package: 2
    real memory  = 1071579136 (1021 MB)
    avail memory = 1018007552 (970 MB)
    ACPI APIC Table: <nvidia nvdaacpi="">
    FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs
     cpu0 (BSP): APIC ID:  0
     cpu1 (AP): APIC ID:  1
    ACPI Warning (tbfadt-0505): Optional field "Pm2ControlBlock" has zero address or length:        0       0/1 [20070320]
    ioapic0: Changing APIC ID to 4
    ioapic0 <version 1.1=""> irqs 0-23 on motherboard
    wlan: mac acl policy registered
    kbd1 at kbdmux0
    cryptosoft0: <software crypto=""> on motherboard
    padlock0: No ACE support.
    acpi0: <nvidia nvdaacpi=""> on motherboard
    acpi0: [ITHREAD]
    acpi0: Power Button (fixed)
    acpi0: reservation of 100000, 3fdf0000 (3) failed
    acpi0: reservation of 0, a0000 (3) failed
    Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
    acpi_timer0: <24-bit timer at 3.579545MHz> port 0x1008-0x100b on acpi0
    acpi_hpet0: <high precision="" event="" timer=""> iomem 0xfeff0000-0xfeff03ff on acpi0
    Timecounter "HPET" frequency 25000000 Hz quality 900
    acpi_button0: <power button=""> on acpi0
    pcib0: <acpi host-pci="" bridge=""> port 0xcf8-0xcff on acpi0
    pci0: <acpi pci="" bus=""> on pcib0
    pci0: <memory, ram=""> at device 0.1 (no driver attached)
    pci0: <memory, ram=""> at device 1.0 (no driver attached)
    pci0: <memory, ram=""> at device 1.1 (no driver attached)
    pci0: <memory, ram=""> at device 1.2 (no driver attached)
    pci0: <memory, ram=""> at device 1.3 (no driver attached)
    pci0: <memory, ram=""> at device 1.4 (no driver attached)
    pci0: <memory, ram=""> at device 1.5 (no driver attached)
    pci0: <memory, ram=""> at device 1.6 (no driver attached)
    pci0: <memory, ram=""> at device 2.0 (no driver attached)
    isab0: <pci-isa bridge=""> at device 3.0 on pci0
    isa0: <isa bus=""> on isab0
    pci0: <serial bus,="" smbus=""> at device 3.1 (no driver attached)
    pci0: <memory, ram=""> at device 3.2 (no driver attached)
    pci0: <memory, ram=""> at device 3.4 (no driver attached)
    ohci0: <ohci (generic)="" usb="" controller=""> mem 0xeffff000-0xefffffff irq 21 at device 4.0 on pci0
    ohci0: [GIANT-LOCKED]
    ohci0: [ITHREAD]
    usb0: OHCI version 1.0, legacy support
    usb0: SMM does not respond, resetting
    usb0: <ohci (generic)="" usb="" controller=""> on ohci0
    usb0: USB revision 1.0
    uhub0: <nvidia 1="" 9="" ohci="" root="" hub,="" class="" 0,="" rev="" 1.00="" 1.00,="" addr=""> on usb0
    uhub0: 10 ports with 10 removable, self powered
    ehci0: <ehci (generic)="" usb="" 2.0="" controller=""> mem 0xefffe000-0xefffe0ff irq 22 at device 4.1 on pci0
    ehci0: [GIANT-LOCKED]
    ehci0: [ITHREAD]
    usb1: EHCI version 1.0
    usb1: companion controller, 10 ports each: usb0
    usb1: <ehci (generic)="" usb="" 2.0="" controller=""> on ehci0
    usb1: USB revision 2.0
    uhub1: <nvidia 1="" 9="" ehci="" root="" hub,="" class="" 0,="" rev="" 2.00="" 1.00,="" addr=""> on usb1
    uhub1: 10 ports with 10 removable, self powered
    atapci0: <nvidia nforce="" mcp73="" udma133="" controller=""> port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xfc00-0xfc0f at device 8.0 on pci0
    ata0: <ata 0="" channel=""> on atapci0
    ata0: [ITHREAD]
    ata1: <ata 1="" channel=""> on atapci0
    ata1: [ITHREAD]
    pcib1: <acpi pci-pci="" bridge=""> at device 10.0 on pci0
    pci1: <acpi pci="" bus=""> on pcib1
    sis0: <natsemi 10="" dp8381[56]="" 100basetx=""> port 0xbe00-0xbeff mem 0xefaff000-0xefafffff irq 18 at device 6.0 on pci1
    sis0: Silicon Revision: DP83815D
    miibus0: <mii bus=""> on sis0
    nsphyter0: <dp83815 10="" 100="" media="" interface=""> PHY 0 on miibus0
    nsphyter0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
    sis0: Ethernet address: 00:02:e3:0a:b2:02
    sis0: [ITHREAD]
    ath0: <atheros 5212=""> mem 0xefae0000-0xefaeffff irq 19 at device 7.0 on pci1
    ath0: [ITHREAD]
    ath0: WARNING: using obsoleted if_watchdog interface
    ath0: Ethernet address: 00:1b:2f:2c:b0:75
    ath0: mac 7.9 phy 4.5 radio 5.6
    pcib2: <acpi pci-pci="" bridge=""> at device 11.0 on pci0
    pci2: <acpi pci="" bus=""> on pcib2
    pcib3: <acpi pci-pci="" bridge=""> at device 12.0 on pci0
    pci3: <acpi pci="" bus=""> on pcib3
    pcib4: <acpi pci-pci="" bridge=""> at device 13.0 on pci0
    pci4: <acpi pci="" bus=""> on pcib4
    re0: <realtek 8168="" 8168b="" 8168c="" 8168cp="" 8168d="" 8111b="" 8111c="" 8111cp="" pcie="" gigabit="" ethernet=""> port 0xce00-0xceff mem 0xefcff000-0xefcfffff irq 16 at device 0.0 on pci4
    re0: Using 1 MSI messages
    re0: Chip rev. 0x38000000
    re0: MAC rev. 0x00000000
    miibus1: <mii bus=""> on re0
    rgephy0: <rtl8169s 8110s="" 8211b="" media="" interface=""> PHY 1 on miibus1
    rgephy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto
    re0: Ethernet address: 00:e0:4d:62:31:01
    re0: [FILTER]
    vgapci0: <vga-compatible display=""> mem 0xed000000-0xedffffff,0xd0000000-0xdfffffff,0xee000000-0xeeffffff irq 23 at device 16.0 on pci0
    acpi_tz0: <thermal zone=""> on acpi0
    speaker0: <pc speaker=""> port 0x61 on acpi0
    sio0: <16550A-compatible COM port> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0
    sio0: type 16550A
    sio0: [FILTER]
    cpu0: <acpi cpu=""> on acpi0
    p4tcc0: <cpu frequency="" thermal="" control=""> on cpu0
    cpu1: <acpi cpu=""> on acpi0
    p4tcc1: <cpu frequency="" thermal="" control=""> on cpu1
    pmtimer0 on isa0
    orm0: <isa option="" rom=""> at iomem 0xd0000-0xd3fff pnpid ORM0000 on isa0
    atkbdc0: <keyboard controller="" (i8042)=""> at port 0x60,0x64 on isa0
    atkbd0: <at keyboard=""> irq 1 on atkbdc0
    kbd0 at atkbd0
    atkbd0: [GIANT-LOCKED]
    atkbd0: [ITHREAD]
    sc0: <system console=""> at flags 0x100 on isa0
    sc0: VGA <16 virtual consoles, flags=0x300>
    sio1: configured irq 3 not in bitmap of probed irqs 0
    sio1: port may not be enabled
    vga0: <generic isa="" vga=""> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
    ugen0: <american 0="" 2="" 1000="" power="" conversion="" back-ups="" rs="" fw:7.g3="" .d="" usb="" fw:g3,="" class="" 0,="" rev="" 1.10="" 1.06,="" addr=""> on uhub0
    Timecounters tick every 1.000 msec
    IPsec: Initialized Security Association Processing.
    acd0: CDROM <compaq cd-rom="" sc-148e="" b902=""> at ata0-master PIO4
    ad1: 38166MB <seagate st340019ace="" 9.51=""> at ata0-slave UDMA100
    SMP: AP CPU #1 Launched!
    Trying to mount root from ufs:/dev/ad1s1a
    sis0: Applying short cable fix (reg=f5)
    sis0: Applying short cable fix (reg=eb)
    sis0: Applying short cable fix (reg=eb)
    bridge0: Ethernet address: e6:c2:7b:50:8e:fd
    sis0: Applying short cable fix (reg=ea)
    sis0: Applying short cable fix (reg=eb)
    pflog0: promiscuous mode enabled
    re0: link state changed to UP
    ath0: stuck beacon; resetting (bmiss count 4)
    re0: promiscuous mode enabled
    re0: promiscuous mode disabled
    re0: promiscuous mode enabled
    pflog0: promiscuous mode disabled
    Waiting (max 60 seconds) for system process `vnlru' to stop...done
    Waiting (max 60 seconds) for system process `bufdaemon' to stop...done
    Waiting (max 60 seconds) for system process `syncer' to stop...
    Syncing disks, vnodes remaining...0 done
    All buffers synced.
    Copyright (c) 1992-2009 The FreeBSD Project.
    Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
    	The Regents of the University of California. All rights reserved.
    FreeBSD is a registered trademark of The FreeBSD Foundation.
    FreeBSD 7.2-RELEASE-p5 #0: Sun Dec  6 23:20:31 EST 2009
        sullrich@FreeBSD_7.2_pfSense_1.2.3_snaps.pfsense.org:/usr/obj.pfSense/usr/pfSensesrc/src/sys/pfSense_SMP.7
    Timecounter "i8254" frequency 1193182 Hz quality 0
    CPU: Intel(R) Pentium(R) D  CPU 2.66GHz (2666.69-MHz 686-class CPU)
      Origin = "GenuineIntel"  Id = 0xf47  Stepping = 7
      Features=0xbfebfbff <fpu,vme,de,pse,tsc,msr,pae,mce,cx8,apic,sep,mtrr,pge,mca,cmov,pat,pse36,clflush,dts,acpi,mmx,fxsr,sse,sse2,ss,htt,tm,pbe>Features2=0x651d <sse3,dtes64,mon,ds_cpl,tm2,cnxt-id,cx16,xtpr>AMD Features=0x20100000 <nx,lm>AMD Features2=0x1 <lahf>Cores per package: 2
    real memory  = 1071579136 (1021 MB)
    avail memory = 1018007552 (970 MB)
    ACPI APIC Table: <nvidia nvdaacpi="">
    FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs
     cpu0 (BSP): APIC ID:  0
     cpu1 (AP): APIC ID:  1
    ACPI Warning (tbfadt-0505): Optional field "Pm2ControlBlock" has zero address or length:        0       0/1 [20070320]
    ioapic0: Changing APIC ID to 4
    ioapic0 <version 1.1=""> irqs 0-23 on motherboard
    wlan: mac acl policy registered
    kbd1 at kbdmux0
    cryptosoft0: <software crypto=""> on motherboard
    padlock0: No ACE support.
    acpi0: <nvidia nvdaacpi=""> on motherboard
    acpi0: [ITHREAD]
    acpi0: Power Button (fixed)
    acpi0: reservation of 100000, 3fdf0000 (3) failed
    acpi0: reservation of 0, a0000 (3) failed
    Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
    acpi_timer0: <24-bit timer at 3.579545MHz> port 0x1008-0x100b on acpi0
    acpi_hpet0: <high precision="" event="" timer=""> iomem 0xfeff0000-0xfeff03ff on acpi0
    Timecounter "HPET" frequency 25000000 Hz quality 900
    acpi_button0: <power button=""> on acpi0
    pcib0: <acpi host-pci="" bridge=""> port 0xcf8-0xcff on acpi0
    pci0: <acpi pci="" bus=""> on pcib0
    pci0: <memory, ram=""> at device 0.1 (no driver attached)
    pci0: <memory, ram=""> at device 1.0 (no driver attached)
    pci0: <memory, ram=""> at device 1.1 (no driver attached)
    pci0: <memory, ram=""> at device 1.2 (no driver attached)
    pci0: <memory, ram=""> at device 1.3 (no driver attached)
    pci0: <memory, ram=""> at device 1.4 (no driver attached)
    pci0: <memory, ram=""> at device 1.5 (no driver attached)
    pci0: <memory, ram=""> at device 1.6 (no driver attached)
    pci0: <memory, ram=""> at device 2.0 (no driver attached)
    isab0: <pci-isa bridge=""> at device 3.0 on pci0
    isa0: <isa bus=""> on isab0
    pci0: <serial bus,="" smbus=""> at device 3.1 (no driver attached)
    pci0: <memory, ram=""> at device 3.2 (no driver attached)
    pci0: <memory, ram=""> at device 3.4 (no driver attached)
    ohci0: <ohci (generic)="" usb="" controller=""> mem 0xeffff000-0xefffffff irq 21 at device 4.0 on pci0
    ohci0: [GIANT-LOCKED]
    ohci0: [ITHREAD]
    usb0: OHCI version 1.0, legacy support
    usb0: SMM does not respond, resetting
    usb0: <ohci (generic)="" usb="" controller=""> on ohci0
    usb0: USB revision 1.0
    uhub0: <nvidia 1="" 9="" ohci="" root="" hub,="" class="" 0,="" rev="" 1.00="" 1.00,="" addr=""> on usb0
    uhub0: 10 ports with 10 removable, self powered
    ehci0: <ehci (generic)="" usb="" 2.0="" controller=""> mem 0xefffe000-0xefffe0ff irq 22 at device 4.1 on pci0
    ehci0: [GIANT-LOCKED]
    ehci0: [ITHREAD]
    usb1: EHCI version 1.0
    usb1: companion controller, 10 ports each: usb0
    usb1: <ehci (generic)="" usb="" 2.0="" controller=""> on ehci0
    usb1: USB revision 2.0
    uhub1: <nvidia 1="" 9="" ehci="" root="" hub,="" class="" 0,="" rev="" 2.00="" 1.00,="" addr=""> on usb1
    uhub1: 10 ports with 10 removable, self powered
    atapci0: <nvidia nforce="" mcp73="" udma133="" controller=""> port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xfc00-0xfc0f at device 8.0 on pci0
    ata0: <ata 0="" channel=""> on atapci0
    ata0: [ITHREAD]
    ata1: <ata 1="" channel=""> on atapci0
    ata1: [ITHREAD]
    pcib1: <acpi pci-pci="" bridge=""> at device 10.0 on pci0
    pci1: <acpi pci="" bus=""> on pcib1
    sis0: <natsemi 10="" dp8381[56]="" 100basetx=""> port 0xbe00-0xbeff mem 0xefaff000-0xefafffff irq 18 at device 6.0 on pci1
    sis0: Silicon Revision: DP83815D
    miibus0: <mii bus=""> on sis0
    nsphyter0: <dp83815 10="" 100="" media="" interface=""> PHY 0 on miibus0
    nsphyter0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
    sis0: Ethernet address: 00:02:e3:0a:b2:02
    sis0: [ITHREAD]
    ath0: <atheros 5212=""> mem 0xefae0000-0xefaeffff irq 19 at device 7.0 on pci1
    ath0: [ITHREAD]
    ath0: WARNING: using obsoleted if_watchdog interface
    ath0: Ethernet address: 00:1b:2f:2c:b0:75
    ath0: mac 7.9 phy 4.5 radio 5.6
    pcib2: <acpi pci-pci="" bridge=""> at device 11.0 on pci0
    pci2: <acpi pci="" bus=""> on pcib2
    pcib3: <acpi pci-pci="" bridge=""> at device 12.0 on pci0
    pci3: <acpi pci="" bus=""> on pcib3
    pcib4: <acpi pci-pci="" bridge=""> at device 13.0 on pci0
    pci4: <acpi pci="" bus=""> on pcib4
    vgapci0: <vga-compatible display=""> mem 0xed000000-0xedffffff,0xd0000000-0xdfffffff,0xee000000-0xeeffffff irq 23 at device 16.0 on pci0
    acpi_tz0: <thermal zone=""> on acpi0
    speaker0: <pc speaker=""> port 0x61 on acpi0
    sio0: <16550A-compatible COM port> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0
    sio0: type 16550A
    sio0: [FILTER]
    atkbdc0: <keyboard controller="" (i8042)=""> port 0x60,0x64 irq 1 on acpi0
    atkbd0: <at keyboard=""> irq 1 on atkbdc0
    kbd0 at atkbd0
    atkbd0: [GIANT-LOCKED]
    atkbd0: [ITHREAD]
    cpu0: <acpi cpu=""> on acpi0
    p4tcc0: <cpu frequency="" thermal="" control=""> on cpu0
    cpu1: <acpi cpu=""> on acpi0
    p4tcc1: <cpu frequency="" thermal="" control=""> on cpu1
    pmtimer0 on isa0
    orm0: <isa option="" rom=""> at iomem 0xd0000-0xd3fff pnpid ORM0000 on isa0
    sc0: <system console=""> at flags 0x100 on isa0
    sc0: VGA <16 virtual consoles, flags=0x300>
    sio1: configured irq 3 not in bitmap of probed irqs 0
    sio1: port may not be enabled
    vga0: <generic isa="" vga=""> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
    ugen0: <american 0="" 2="" 1000="" power="" conversion="" back-ups="" rs="" fw:7.g3="" .d="" usb="" fw:g3,="" class="" 0,="" rev="" 1.10="" 1.06,="" addr=""> on uhub0
    Timecounters tick every 1.000 msec
    IPsec: Initialized Security Association Processing.
    acd0: CDROM <compaq cd-rom="" sc-148e="" b902=""> at ata0-master PIO4
    ad1: 38166MB <seagate st340019ace="" 9.51=""> at ata0-slave UDMA100
    SMP: AP CPU #1 Launched!
    Trying to mount root from ufs:/dev/ad1s1a
    sis0: Applying short cable fix (reg=f5)
    sis0: Applying short cable fix (reg=ea)
    sis0: Applying short cable fix (reg=ea)
    pflog0: promiscuous mode enabled
    pflog0: promiscuous mode disabled
    Waiting (max 60 seconds) for system process `vnlru' to stop...done
    Waiting (max 60 seconds) for system process `syncer' to stop...
    Syncing disks, vnodes remaining...0 0 done
    Waiting (max 60 seconds) for system process `bufdaemon' to stop...done
    All buffers synced.
    Copyright (c) 1992-2009 The FreeBSD Project.
    Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
    	The Regents of the University of California. All rights reserved.
    FreeBSD is a registered trademark of The FreeBSD Foundation.
    FreeBSD 7.2-RELEASE-p5 #0: Sun Dec  6 23:20:31 EST 2009
        sullrich@FreeBSD_7.2_pfSense_1.2.3_snaps.pfsense.org:/usr/obj.pfSense/usr/pfSensesrc/src/sys/pfSense_SMP.7
    Timecounter "i8254" frequency 1193182 Hz quality 0
    CPU: Intel(R) Pentium(R) D  CPU 2.66GHz (2666.69-MHz 686-class CPU)
      Origin = "GenuineIntel"  Id = 0xf47  Stepping = 7
      Features=0xbfebfbff <fpu,vme,de,pse,tsc,msr,pae,mce,cx8,apic,sep,mtrr,pge,mca,cmov,pat,pse36,clflush,dts,acpi,mmx,fxsr,sse,sse2,ss,htt,tm,pbe>Features2=0x651d <sse3,dtes64,mon,ds_cpl,tm2,cnxt-id,cx16,xtpr>AMD Features=0x20100000 <nx,lm>AMD Features2=0x1 <lahf>Cores per package: 2
    real memory  = 1071579136 (1021 MB)
    avail memory = 1018007552 (970 MB)
    ACPI APIC Table: <nvidia nvdaacpi="">
    FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs
     cpu0 (BSP): APIC ID:  0
     cpu1 (AP): APIC ID:  1
    ACPI Warning (tbfadt-0505): Optional field "Pm2ControlBlock" has zero address or length:        0       0/1 [20070320]
    ioapic0: Changing APIC ID to 4
    ioapic0 <version 1.1=""> irqs 0-23 on motherboard
    wlan: mac acl policy registered
    kbd1 at kbdmux0
    cryptosoft0: <software crypto=""> on motherboard
    padlock0: No ACE support.
    acpi0: <nvidia nvdaacpi=""> on motherboard
    acpi0: [ITHREAD]
    acpi0: Power Button (fixed)
    acpi0: reservation of 100000, 3fdf0000 (3) failed
    acpi0: reservation of 0, a0000 (3) failed
    Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
    acpi_timer0: <24-bit timer at 3.579545MHz> port 0x1008-0x100b on acpi0
    acpi_hpet0: <high precision="" event="" timer=""> iomem 0xfeff0000-0xfeff03ff on acpi0
    Timecounter "HPET" frequency 25000000 Hz quality 900
    acpi_button0: <power button=""> on acpi0
    pcib0: <acpi host-pci="" bridge=""> port 0xcf8-0xcff on acpi0
    pci0: <acpi pci="" bus=""> on pcib0
    pci0: <memory, ram=""> at device 0.1 (no driver attached)
    pci0: <memory, ram=""> at device 1.0 (no driver attached)
    pci0: <memory, ram=""> at device 1.1 (no driver attached)
    pci0: <memory, ram=""> at device 1.2 (no driver attached)
    pci0: <memory, ram=""> at device 1.3 (no driver attached)
    pci0: <memory, ram=""> at device 1.4 (no driver attached)
    pci0: <memory, ram=""> at device 1.5 (no driver attached)
    pci0: <memory, ram=""> at device 1.6 (no driver attached)
    pci0: <memory, ram=""> at device 2.0 (no driver attached)
    isab0: <pci-isa bridge=""> at device 3.0 on pci0
    isa0: <isa bus=""> on isab0
    pci0: <serial bus,="" smbus=""> at device 3.1 (no driver attached)
    pci0: <memory, ram=""> at device 3.2 (no driver attached)
    pci0: <memory, ram=""> at device 3.4 (no driver attached)
    ohci0: <ohci (generic)="" usb="" controller=""> mem 0xeffff000-0xefffffff irq 21 at device 4.0 on pci0
    ohci0: [GIANT-LOCKED]
    ohci0: [ITHREAD]
    usb0: OHCI version 1.0, legacy support
    usb0: SMM does not respond, resetting
    usb0: <ohci (generic)="" usb="" controller=""> on ohci0
    usb0: USB revision 1.0
    uhub0: <nvidia 1="" 9="" ohci="" root="" hub,="" class="" 0,="" rev="" 1.00="" 1.00,="" addr=""> on usb0
    uhub0: 10 ports with 10 removable, self powered
    ehci0: <ehci (generic)="" usb="" 2.0="" controller=""> mem 0xefffe000-0xefffe0ff irq 22 at device 4.1 on pci0
    ehci0: [GIANT-LOCKED]
    ehci0: [ITHREAD]
    usb1: EHCI version 1.0
    usb1: companion controller, 10 ports each: usb0
    usb1: <ehci (generic)="" usb="" 2.0="" controller=""> on ehci0
    usb1: USB revision 2.0
    uhub1: <nvidia 1="" 9="" ehci="" root="" hub,="" class="" 0,="" rev="" 2.00="" 1.00,="" addr=""> on usb1
    uhub1: 10 ports with 10 removable, self powered
    atapci0: <nvidia nforce="" mcp73="" udma133="" controller=""> port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xfc00-0xfc0f at device 8.0 on pci0
    ata0: <ata 0="" channel=""> on atapci0
    ata0: [ITHREAD]
    ata1: <ata 1="" channel=""> on atapci0
    ata1: [ITHREAD]
    pcib1: <acpi pci-pci="" bridge=""> at device 10.0 on pci0
    pci1: <acpi pci="" bus=""> on pcib1
    sis0: <natsemi 10="" dp8381[56]="" 100basetx=""> port 0xbe00-0xbeff mem 0xefaff000-0xefafffff irq 18 at device 6.0 on pci1
    sis0: Silicon Revision: DP83815D
    miibus0: <mii bus=""> on sis0
    nsphyter0: <dp83815 10="" 100="" media="" interface=""> PHY 0 on miibus0
    nsphyter0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
    sis0: Ethernet address: 00:02:e3:0a:b2:02
    sis0: [ITHREAD]
    ath0: <atheros 5212=""> mem 0xefae0000-0xefaeffff irq 19 at device 7.0 on pci1
    ath0: [ITHREAD]
    ath0: WARNING: using obsoleted if_watchdog interface
    ath0: Ethernet address: 00:1b:2f:2c:b0:75
    ath0: mac 7.9 phy 4.5 radio 5.6
    pcib2: <acpi pci-pci="" bridge=""> at device 11.0 on pci0
    pci2: <acpi pci="" bus=""> on pcib2
    pcib3: <acpi pci-pci="" bridge=""> at device 12.0 on pci0
    pci3: <acpi pci="" bus=""> on pcib3
    pcib4: <acpi pci-pci="" bridge=""> at device 13.0 on pci0
    pci4: <acpi pci="" bus=""> on pcib4
    re0: <realtek 8168="" 8168b="" 8168c="" 8168cp="" 8168d="" 8111b="" 8111c="" 8111cp="" pcie="" gigabit="" ethernet=""> port 0xce00-0xceff mem 0xefcff000-0xefcfffff irq 16 at device 0.0 on pci4
    re0: Using 1 MSI messages
    re0: Chip rev. 0x38000000
    re0: MAC rev. 0x00000000
    miibus1: <mii bus=""> on re0
    rgephy0: <rtl8169s 8110s="" 8211b="" media="" interface=""> PHY 1 on miibus1
    rgephy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto
    re0: Ethernet address: 00:e0:4d:62:31:01
    re0: [FILTER]
    vgapci0: <vga-compatible display=""> mem 0xed000000-0xedffffff,0xd0000000-0xdfffffff,0xee000000-0xeeffffff irq 23 at device 16.0 on pci0
    acpi_tz0: <thermal zone=""> on acpi0
    speaker0: <pc speaker=""> port 0x61 on acpi0
    sio0: <16550A-compatible COM port> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0
    sio0: type 16550A
    sio0: [FILTER]
    atkbdc0: <keyboard controller="" (i8042)=""> port 0x60,0x64 irq 1 on acpi0
    atkbd0: <at keyboard=""> irq 1 on atkbdc0
    kbd0 at atkbd0
    atkbd0: [GIANT-LOCKED]
    atkbd0: [ITHREAD]
    cpu0: <acpi cpu=""> on acpi0
    p4tcc0: <cpu frequency="" thermal="" control=""> on cpu0
    cpu1: <acpi cpu=""> on acpi0
    p4tcc1: <cpu frequency="" thermal="" control=""> on cpu1
    pmtimer0 on isa0
    orm0: <isa option="" rom=""> at iomem 0xd0000-0xd3fff pnpid ORM0000 on isa0
    sc0: <system console=""> at flags 0x100 on isa0
    sc0: VGA <16 virtual consoles, flags=0x300>
    sio1: configured irq 3 not in bitmap of probed irqs 0
    sio1: port may not be enabled
    vga0: <generic isa="" vga=""> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
    ugen0: <american 0="" 2="" 1000="" power="" conversion="" back-ups="" rs="" fw:7.g3="" .d="" usb="" fw:g3,="" class="" 0,="" rev="" 1.10="" 1.06,="" addr=""> on uhub0
    Timecounters tick every 1.000 msec
    IPsec: Initialized Security Association Processing.
    acd0: CDROM <compaq cd-rom="" sc-148e="" b902=""> at ata0-master PIO4
    ad1: 38166MB <seagate st340019ace="" 9.51=""> at ata0-slave UDMA100
    SMP: AP CPU #1 Launched!
    Trying to mount root from ufs:/dev/ad1s1a
    sis0: Applying short cable fix (reg=f6)
    sis0: Applying short cable fix (reg=e8)
    sis0: Applying short cable fix (reg=e7)
    pflog0: promiscuous mode enabled
    re0: promiscuous mode enabled
    re0: promiscuous mode disabled
    re0: promiscuous mode enabled
    sis0: Applying short cable fix (reg=e8)
    re0: link state changed to UP
    re0: link state changed to DOWN
    re0: link state changed to UP
    re0: link state changed to DOWN
    re0: link state changed to UP
    re0: link state changed to DOWN
    re0: link state changed to UP
    re0: link state changed to DOWN
    re0: link state changed to UP
    re0: link state changed to DOWN
    re0: link state changed to UP
    re0: link state changed to DOWN
    re0: link state changed to UP
    re0: link state changed to DOWN
    re0: link state changed to UP
    re0: link state changed to DOWN
    re0: link state changed to UP
    re0: link state changed to DOWN
    re0: link state changed to UP
    re0: link state changed to DOWN
    re0: link state changed to UP
    re0: link state changed to DOWN
    re0: link state changed to UP
    bridge0: Ethernet address: 7e:0c:65:ee:ac:66
    sis0: Applying short cable fix (reg=e9)
    ath0: promiscuous mode enabled
    sis0: Applying short cable fix (reg=e8)
    sis0: promiscuous mode enabled</seagate></compaq></american></generic></system></isa></cpu></acpi></cpu></acpi></at></keyboard></pc></thermal></vga-compatible></rtl8169s></mii></realtek></acpi></acpi></acpi></acpi></acpi></acpi></atheros></dp83815></mii></natsemi></acpi></acpi></ata></ata></nvidia></nvidia></ehci></ehci></nvidia></ohci></ohci></memory,></memory,></serial></isa></pci-isa></memory,></memory,></memory,></memory,></memory,></memory,></memory,></memory,></memory,></acpi></acpi></power></high></nvidia></software></version></nvidia></lahf></nx,lm></sse3,dtes64,mon,ds_cpl,tm2,cnxt-id,cx16,xtpr></fpu,vme,de,pse,tsc,msr,pae,mce,cx8,apic,sep,mtrr,pge,mca,cmov,pat,pse36,clflush,dts,acpi,mmx,fxsr,sse,sse2,ss,htt,tm,pbe></seagate></compaq></american></generic></system></isa></cpu></acpi></cpu></acpi></at></keyboard></pc></thermal></vga-compatible></acpi></acpi></acpi></acpi></acpi></acpi></atheros></dp83815></mii></natsemi></acpi></acpi></ata></ata></nvidia></nvidia></ehci></ehci></nvidia></ohci></ohci></memory,></memory,></serial></isa></pci-isa></memory,></memory,></memory,></memory,></memory,></memory,></memory,></memory,></memory,></acpi></acpi></power></high></nvidia></software></version></nvidia></lahf></nx,lm></sse3,dtes64,mon,ds_cpl,tm2,cnxt-id,cx16,xtpr></fpu,vme,de,pse,tsc,msr,pae,mce,cx8,apic,sep,mtrr,pge,mca,cmov,pat,pse36,clflush,dts,acpi,mmx,fxsr,sse,sse2,ss,htt,tm,pbe></seagate></compaq></american></generic></system></at></keyboard></isa></cpu></acpi></cpu></acpi></pc></thermal></vga-compatible></rtl8169s></mii></realtek></acpi></acpi></acpi></acpi></acpi></acpi></atheros></dp83815></mii></natsemi></acpi></acpi></ata></ata></nvidia></nvidia></ehci></ehci></nvidia></ohci></ohci></memory,></memory,></serial></isa></pci-isa></memory,></memory,></memory,></memory,></memory,></memory,></memory,></memory,></memory,></acpi></acpi></power></high></nvidia></software></version></nvidia></lahf></nx,lm></sse3,dtes64,mon,ds_cpl,tm2,cnxt-id,cx16,xtpr></fpu,vme,de,pse,tsc,msr,pae,mce,cx8,apic,sep,mtrr,pge,mca,cmov,pat,pse36,clflush,dts,acpi,mmx,fxsr,sse,sse2,ss,htt,tm,pbe>
    


  • Thanks for the dmesg output. I thought that there might have been an error found during the re device attach processing on startup but that is not the case here.  Rather it looks as if the device is sometimes not seen during startup. It appears the re is a PCI Express device in which case the PCI Express serial link between the device and its upstream bridge needs to be initialised before the device is visible to the CPU.

    I suggest you look on the Biostar support web pages to see if there any sort of fix for this problem (e.g. maybe the BIOS needs to wait a little longer to allow the PCI Express link to come up) or if its a known but won't be fixed problem (e.g. bug in the NIC silicon). It might also be worth looking through Google to see if ohters have seen a similar problem.



  • your welcome, thanks for the help.

    according to biostar it is a PCIE device. when i find out i will update.

    also is there a way to force a reboot if it doesnt detect the nic?



  • they have requested that I reinstall the driver…how does one reinstall the driver?



  • @XIII:

    they have requested that I reinstall the driver…how does one reinstall the driver?

    One doesn't - the driver is built into the kernel.



  • @wallabybob:

    One doesn't - the driver is built into the kernel.

    Thats what I thought, and thats what I told them.



  • well I had to redo the system for an unrelated problem (just restored to default) and it went away.



  • Problems like that which spontaneously go away leave me suspicious that they will spontaneously come back.



  • by it going away i mean the it doesnt appear on every other reboot like it did, when it goes away it is replaced with error messages that say that nothing was properly dismount and then it cleans the file system then continues to boot, dont know why though.
    I dont reboot that often so I am not sure if it is an issues



  • update: I think it had to do with the fact that I was cloning a MAC address before and am no longer do so at the present moment. I no longer have any file system error messages either, so i think that the realtek just had problems accepting a different MAC.


Locked