No IP address displayed
-
You changed the Ubuntu VM adapter type. That has to be Internal also so it can talk to the pfSense LAN.
Do you have the router connected to the physical NIC that is bridged to the pfSense WAN adapter?
Steve
-
You changed the Ubuntu VM adapter type. That has to be Internal also so it can talk to the pfSense LAN.
Have another round
pfSense
Adapter 1
Bridge
eth0Adapter 2
Internal Network
intnetWAN (wan) -> em1 -> NONE (DHCP)
LAN (lan) -> em0 -> 192.168.1.1VM Ubuntu
Adapter 1
Internal Network
intnet$ sudo ifconfig```
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:65536 Metric:1
RX packets:16 errors:0 dropped:0 overruns:0 frame:0
TX packets:16 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:1312 (1.3 KB) TX bytes:1312 (1.3 KB)$ ping 192.168.1.1``` connect: Network is unreachablepfSense
Adapter 1
Bridge
eth1WAN (wan) -> em1 -> NONE (DHCP)
LAN (lan) -> em0 -> 192.168.1.1VM Ubuntu
Adapter 1
Internal Network
intnet$ sudo ifconfig
eth0 Link encap:Ethernet HWaddr 08:00:27:10:8c:3d inet6 addr: fe80::a00:27ff:fe10:8c3d/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:1 errors:0 dropped:0 overruns:0 frame:0 TX packets:51 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:60 (60.0 B) TX bytes:11704 (11.7 KB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:65536 Metric:1 RX packets:464 errors:0 dropped:0 overruns:0 frame:0 TX packets:464 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:37760 (37.7 KB) TX bytes:37760 (37.7 KB)Do you have the router connected to the physical NIC that is bridged to the pfSense WAN adapter?
No. If PC1 is connected behind a router. It worked already, about 2 days ago.
Present connection:
ISP -> Cable Modem -> PC1
Interface - pppoesatimis
-
Hmm, OK. So if both the pfSense LAN and the Ubuntu NIC are on the same internal network then either the DHCP server is not enabled on the pfSense (it would be enabled by default) or the Ubuntu VM is not set to use DHCP.
In your second setup you can see the Ubuntu VM sees the interface as UP but isn't receiving an IP.If you have the router in place then it will hand out an IP to the pfSense WAN and you will be able see immediately if you have the correct adapters assigned to the interfaces.
Steve
-
Hi Steve
The problem is my modem only has 1 IP address to assign. Debian Host is getting this IP address before pfSense starts up. I must sort out this problem first. Secondly login and password are needed for assigning IP address. Where shall I enter them to assign the IP address to pfSense in order to get connection to Internet?
satimis
-
Well you could do that but as you say you need to be able to enter the PPP username/password to pfSense and you can only do that (without resorting to manually editing files) via the webgui. To access the webgui you need to sort out the connection between the pfSense LAN interface and Ubutu VM you're using for administration.
If you put the router back inplace between the modem and PC1 then it will hand out a private IP to pfSense which you will be able to immediately see in the pfSense console. That will make it much easier to determine that you have the LAN interface assigned to the correct VM adapter and that that adapter is configured correctly.Steve
-
Cannot you just add serial port in Virtualbox and use that as console?
-
You could but there's no need to do that you can already access the virtual VGA console. To configure the WAN for PPPoE you pretty much need to do it from the LAN side via the webgui.
Any second opinions on this are welcomed. As I said earlier in the thread I've used VBox only a few times and not recently so most of what I've said here is based on research rather than experience.
Steve
-
Only have ESXi and Hyper-V boxes available ATM, so… afraid I won't be of much help. I kinda don't understand what's the trouble here then. The web GUI does not work with WAN down, or what? If it does not, what's the problem with assigning some static temp IP to WAN meanwhile, just to get it running?
-
There are two issues.
The first is configuring the pfSense WAN interface to connect using PPPoE via a bridged adapter in VBox to the physical NIC and the cable modem. However we havne't yet actually tackled that because of the second issue…
Configuring the pfSense WAN to PPPoE needs (or is very much easier) to be done from the LAN side. Here the LAN interface is connected to an internal virtual network only so we have added an Ubuntu VM on that same network in order to fire up a browser and point it at the pfSense webgui. Currently the Ubuntu VM is not receiving an IP from the pfSense DHCP server. This should be pretty easy to accomplish. It's not helped by the fact that earlier access to the pfSense webgui was established via some accidental bridging route.If you're up for it read back through the thread, try not to shout at the computer to much! ;)
Steve
-
Hi all,
Performed following steps but still fail.
Connection
ISP -> Modem -> PCMake following changes:
Host
/etc/network/interfaces```
The loopback network interface
auto lo
iface lo inet loopbackauto eth0
iface eth0 inet static
#(configure Debian host not using DHCP for the eth0 interface)auto vboxnet0
iface vboxnet0 inet dhcp
#(configure debian host to connect to the pfSence router via the LAN port)pfSense: ====== NIC1 of pfSence host - Adapter 1 - Bridged to eth0\. (also tried eth1/Internal Network) NIC2 Adapter 2 - Host-Only Adapter Name vboxnet0 Reboot Host $ sudo ifconfig``` eth1 Link encap:Ethernet HWaddr 90:f6:52:03:57:86 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:43 Base address:0xc000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:24 errors:0 dropped:0 overruns:0 frame:0 TX packets:24 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:1584 (1.5 KiB) TX bytes:1584 (1.5 KiB) vboxnet0 Link encap:Ethernet HWaddr 0a:00:27:00:00:00 inet addr:192.168.56.1 Bcast:192.168.56.255 Mask:255.255.255.0 inet6 addr: fe80::800:27ff:fe00:0/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:54 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:9229 (9.0 KiB)Started pfSense
.... .... Configuring WAN interface .... starting pppoe link... done ....... Starting NTP time client...Error : hostname nor servname provided, or not known (held here for sometime) WAN (wan) -> pppoe0 -> NONE (PPPoE) LAN (lan) -> em0 -> 192.168.1.1 .... ....(see attached photo image)
VM Ubuntu 12.04 64bit
Adapter -1
Bridge
eth0Start VM
Warning:```The virtual machine execution may run into an error condition as
described below. We suggest that you take an appropriate
action to avert the error.Bridged interface eth0 is down. Guest will not be able to use
this interface.Details
Error ID: BridgeInterfaceDown
Severity: WarningLogin pfSense (192.168.1.1) Username admin Password pfsense -> Login -> Interfaces -> WAN Description WAN Type PPPoE Username (xxxxxxx) Password (xxxxxx) (check) Block private networks Block bogon networks -> Save Warning``` Interfaces: WAN The WAN configuration has been changed. You must apply the changes in order for them to take effect. Don't forget to adjust the DHCP Server range if needed after applying.-> Apply Changes
-> Status -> Interfaces -> click (connect)
Still failed (see attached photo image)
According to following document:-
pfSense initial configuration with ADSL WAN
http://www.interspective.net/2012/05/pfsense-initial-configuration-adsl-wan.html.... The first thing you want to do is use a web browser to connect to your old modem / router and set the WAN interface to 'Bridge Mode'. Once you've logged in you will need to find the WAN type....First I'm not allowed to touch the modem, impossible making change on its settings. Besides there will be no sense using the router to continue this test. My goal is using vRouter (pfSense)
I think my chance of success being remote? I'll buy a new router after switching to the new ISP on the coming April (the current router is on loan).
Rgds
satimis
-
If you are not able to configure the modem in any way, you cannot use pfSense to dial PPPoE. That's pretty much the whole story.
-
If you are not able to configure the modem in any way, you cannot use pfSense to dial PPPoE. That's pretty much the whole story.
Hi,
Thanks for your advice.
I consider not to spend further effort here because less than a month I'll use a new ISP. Then I'll try again before purchasing a new router. I'm subscribing Static IP. I'll make request to the new ISP for changing the settings on their ONT. They'll provide ONT not cable modem for HTTH Optical Fibre Network. My current ISP is not providing Optical Fibre Service.
I have the photo of the ONT attached here which is provided by the new ISP
There are 2 ports. I think I can use them connecting my 2 PCs? But how to assign LAN IP to VMs without a router?
Rgds
satimis
-
You don't need to put your router in bridge mode because you have a separate modem and router. You have removed the router entirely leaving just the modem which expects to see a PPPoE connection.
Here's the think though. You are making this far more difficult than it needs to be by trying to do everything at once. The way to solve problems like this is to do in one step at a time. Right now you're trying to solve the PPPoE connection, the connection to the host and connection to the Ubuntu VM simultaneously. You are also changing many things between each post so that diagnosing what effect the changed have had becomes far more difficult.
The 192.168.56.X address given by the host only adapter to the host is an address given out by VBox when it's NATing. You probably don't want that.
Here's what I would do:
Solve one thing at a time. So first I would setup the connection between the pfSense VM and the Ubuntu administration VM.
Please put the router back in place so that it's handing out IPs. Setup the pfSense VM with two adapters as you did before:pfSense
Adapter 1
Bridge
eth0Adapter 2
Internal Network
intnetSet the pfSense WAN interface to DHCP. It should receive an IP address on the WAN from the router. Now you know you have the correct adapter assigned to the WAN.
Set the Ubuntu VM adapter to:
Adapter 1
Internal Network
intnetSet Ubuntu to use DHCP. Now it should receive an IP address from the pfSense DHCP server. If it does not we will try to solve that first before doing anything else. We need that connection work.
Steve
-
- snip -
Please put the router back in place so that it's handing out IPs. Setup the pfSense VM with two adapters as you did before:
pfSense
Adapter 1
Bridge
eth0Adapter 2
Internal Network
intnetSet the pfSense WAN interface to DHCP. It should receive an IP address on the WAN from the router. Now you know you have the correct adapter assigned to the WAN.
Set the Ubuntu VM adapter to:
Adapter 1
Internal Network
intnetSet Ubuntu to use DHCP. Now it should receive an IP address from the pfSense DHCP server. If it does not we will try to solve that first before doing anything else. We need that connection work.
Set connection as advised;
ISP -> Modem -> Router -> PC
also set config as advised.
Started pfSense followed by VM
Login gui pfSense
Wan -> DHCP
-> Applied changesStatus -> Interfaces
Status down
DHCP down [renew] (no function on clicking)Rebooted pfSense, it held here;```
.....
Do you want tp set VLANs [y|n] em1: DAD detected duplicate IPv6 address
fe80:2::226:10ff:fe44:b61a: NS in/out=0/1 NA in=1
em1: DAD complete for fe80:2::226:10ff:fe44:b61a - duplicate found
em1: manual intervention required
em1: possible hardware address duplication detected,l disable IPv6Edit: === Host /etc/network/interfaces``` # The loopback network interface auto lo iface lo inet loopbacksatimis
-
Ok, well we have some new information at least!
That duplicated IPv6 address is probably because both the pfSense WAN and the Host, PC1, are requesting addresses using the same MAC address. They share the same physical MAC. I'm unsure why that didn't happen before. There is probably a work around by spoofing the MAC but if you don't need IPv6 you can just go to Interfaces: WAN: and set the IPv6 configuration type to 'none'. I assume you had set that to DHCP. Obviously leave the IPv4 type as DHCP.So you had no problem connecting to the LAN from the Ubuntu VM? Did it receive an IP from the pfSense DHCP server? You can check it in Status: DHCP leases:
Steve
-
On Host before firing up pfSense
$ sudo ifconfig```
eth0 Link encap:Ethernet HWaddr 00:26:18:44:b6:1a
inet addr:192.168.0.10 Bcast:192.168.0.255 Mask:255.255.255.0
inet6 addr: fe80::226:18ff:fe44:b61a/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:231980 errors:0 dropped:0 overruns:0 frame:0
TX packets:144575 errors:0 dropped:0 overruns:0 carrier:1
collisions:0 txqueuelen:1000
RX bytes:322513726 (307.5 MiB) TX bytes:13891455 (13.2 MiB)
Interrupt:18eth1 Link encap:Ethernet HWaddr 90:f6:52:03:57:86
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
Interrupt:43 Base address:0x4000lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:8 errors:0 dropped:0 overruns:0 frame:0
TX packets:8 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:480 (480.0 B) TX bytes:480 (480.0 B)> That duplicated IPv6 address is probably because both the pfSense WAN and the Host, PC1, are requesting addresses using the same MAC address. They share the same physical MAC. I'm unsure why that didn't happen before. There is probably a work around by spoofing the MAC but if you don't need IPv6 you can just go to Interfaces: WAN: and set the IPv6 configuration type to 'none'. I assume you had set that to DHCP. Obviously leave the IPv4 type as DHCP. Before changing pppoe back to DHCP I have put the MAC Address of eth0 "00:26:18:44:b6:1a" there (IIRC). During changing pppoe to DHCP I deleted that MAC Address. Now I couldn't start pfSense anymore it was held on;``` ..... Do you want tp set VLANs [y|n] em1: DAD detected duplicate IPv6 address fe80:2::226:10ff:fe44:b61a: NS in/out=0/1 NA in=1 em1: DAD complete for fe80:2::226:10ff:fe44:b61a - duplicate found em1: manual intervention required em1: possible hardware address duplication detected,l disable IPv6satimis
-
So you tried disabling DHCPv6?
At that screen you should still be able to answer 'N' to the VLANs question and continue the pfSense setup. The duplicate IP warning is just informational. It shouldn't stop you continuing.
Steve
-
So you tried disabling DHCPv6?
At that screen you should still be able to answer 'N' to the VLANs question and continue the pfSense setup. The duplicate IP warning is just informational. It shouldn't stop you continuing.
I was stuck there. Actually I was not allowed to keyin any imput. All were done automatically eversince starting pfSense.
This version of pfSense was imported on pfSense-2.0.3-RELEASE-amd64.ova download on Internet. Would this .ova have problem?
I also have pfSense-LiveCD-2.1-RELEASE-amd64.iso.gz download. I can create another VM installing this version.
satimis
-
Hi Steve
Created another pfSense VM (name=pfSense2.1) on pfSense-LiveCD-2.1-RELEASE-amd64.iso.gz download on pfSense site.
pfSense2.1 ======== Adapter 1 Bridge eth0 Adapter 2 Internal Network intnetVM Ubuntu 12.04 ============== Adapter 1 Internal Network intnetThis time it works
–-------------------
Fire up pfSense2.1WAN (wan) -> em0 -> v4/DHCP4: 192.168.0.15/24 LAN (lan) -> em1 -> v4: 192.168.1.1/24WAN gets DHCP on physical Router
Start VM
$ sudo ifconfig```
eth1 Link encap:Ethernet HWaddr 08:00:27:5a:3d:a4
inet addr:192.168.1.101 Bcast:192.168.1.255 Mask:255.255.255.0
inet6 addr: fe80::a00:27ff:fe5a:3da4/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:12104 errors:0 dropped:0 overruns:0 frame:0
TX packets:10357 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:13944700 (13.9 MB) TX bytes:1169137 (1.1 MB)lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:65536 Metric:1
RX packets:1627 errors:0 dropped:0 overruns:0 frame:0
TX packets:1627 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:226777 (226.7 KB) TX bytes:226777 (226.7 KB)VM obtains IP on pfSense2.1 I can login pfSense2.1 on VM satimis -
Ok, excellent. Remember those settings! :)
So now there are two further problems to be tackled one at a time.
1. Change the WAN connection to PPPoE directly from pfSense.
2. Add a host adapter so the host also uses pfSense as it's internet gateway.Personally I would try to do 1 first but it's up to you. Don't try to do both at the same time though it will only introduce further confusion.
Steve
