Make sure /var/squid/log actually exists and has the correct permissions. Usually, though, it's /var/squid/logs.

I searched back through logs and it looks like a result of switching architecture from 32-bit to 64-bit but that was back when I installed 2.1 beta. Strange that the error suddenly changed from "This RRD was created on other architecture" which I had never noticed. Reset the RRD data and all appears to be OK.

Ok… I didn't know that adding/removing a Cron job with a max. frequency of 2 minutes could be a problem or something to avoid... Also, what do you think is better, to use a "single text file" to store the notifications or use different small text file, one for each single notification? I am just worry that when 300 or more notifications are generated in few seconds there could be some kind of problem in managing the single text file...

update.. after a while that I tick out of allow IPv6, system log still show repeat the message as above. Oct 9 18:50:15 php: rc.filter_configure_sync: Could not find IPv6 gateway for interface(opt4). Oct 9 18:50:15 php: rc.filter_configure_sync: Could not find IPv6 gateway for interface(wan). Oct 9 18:50:10 check_reload_status: Reloading filter Oct 9 18:50:10 check_reload_status: Restarting OpenVPN tunnels/interfaces Oct 9 18:50:10 check_reload_status: Restarting ipsec tunnels Oct 9 18:50:10 check_reload_status: updating dyndns VPNGW Oct 9 18:49:56 php: rc.filter_configure_sync: Could not find IPv6 gateway for interface(opt4). Oct 9 18:49:55 php: rc.filter_configure_sync: Could not find IPv6 gateway for interface(wan). Oct 9 18:49:50 check_reload_status: Reloading filter Oct 9 18:49:50 check_reload_status: Restarting OpenVPN tunnels/interfaces Oct 9 18:49:50 check_reload_status: Restarting ipsec tunnels Oct 9 18:49:50 check_reload_status: updating dyndns VPNGW Oct 9 18:48:35 php: rc.filter_configure_sync: Could not find IPv6 gateway for interface(opt4). Oct 9 18:48:35 php: rc.filter_configure_sync: Could not find IPv6 gateway for interface(wan). Oct 9 18:48:30 check_reload_status: Reloading filter Oct 9 18:48:30 check_reload_status: Restarting OpenVPN tunnels/interfaces Oct 9 18:48:30 check_reload_status: Restarting ipsec tunnels Oct 9 18:48:30 check_reload_status: updating dyndns VPNGW Oct 9 18:47:50 php: rc.filter_configure_sync: Could not find IPv6 gateway for interface(opt4). Oct 9 18:47:50 php: rc.filter_configure_sync: Could not find IPv6 gateway for interface(wan). Oct 9 18:47:45 check_reload_status: Reloading filter Oct 9 18:47:45 check_reload_status: Restarting OpenVPN tunnels/interfaces Oct 9 18:47:45 check_reload_status: Restarting ipsec tunnels Oct 9 18:47:45 check_reload_status: updating dyndns VPNGW

To update: Progress maybe just to the side tho!! Two servers: 192.168.1.200 & 192.168.1.201 Urls: 1.a.com, 2.a.com, 3.a.com, 4.a.com. The two servers are set up as peers within the Webservers Tab of Reverse Proxy, they are both listed on port 80 and have their relevant IP address listed. subdomains 1 and 2 are meant to go to 192.168.1.200. 3 and 4 should go to 192.168.1.201. Everything is going to 200. Ideas?

I can now confirm that with pfsense 2.1 BPDUs are exchanged properly when rstp is enabled on a bridge with the root bridge upstream. I ended up setting my 2950 switches to rstp defaults except for a cost of 37 on port 3 to put the pfsense2 box Lagg0 Lan interface into blocking mode. All is well!

Bah!  Was looking at the UNIX man of date… http://unixhelp.ed.ac.uk/CGI/man-cgi?date

Just updating this to say that I increased /var to 80MB and haven't had an issue since. Steve

Well now I feel as your just throwing me a bone ;)  with that fine statement – hehehe As to security -- I personally have no issue with ping being allowed, and even it allow my public ip to answer ping..  Allowing it on your internal network should not be an issue at all.

@nightwalk74: It is NAS that I am most interested in having it own NIC. Why?

Yes, if you have to provide real performance, then don't use a USB Network Adapter. If you have only 1 physical port available for LAN, then you are going to need VLANs - buy a VLAN switch and connect it to the LAN port… There is going to be downtime in changing over!

Thanks a lot for you help.I installed the healthd package tried all the parameters and i also get wrong temps. I actually get 255.0 as a cpu temp.  :P Well this ADM1025 is way too old to be monitored.Even the bios dont have a monitor utility.Anyway thanks a lot for your help. Friendly Nick.

Thanks everyone I created two new rules TCP LAN net * -> Routers 80 (HTTP) ICMP LAN net * -> Routers * Works a treat

Or install package crond and schedule reboot etc.

Is that working via port forward? If so… https://doc.pfsense.org/index.php/Why_can%27t_I_access_forwarded_ports_on_my_WAN_IP_from_my_LAN/OPTx_networks%3F

Clear your browsers cache/cookies etc and try again. @hackin8: When opening the dashboard in IE8 everything appears to work, but the display never refreshes - just sits open on original view showing "CPU updating in 10 secs…"  but it never does. Manually refreshing gets a new date / time - but no CPU, just same message. I am running 2.1 on an Alix - works fine from other computers, locally. I am trying to access through VPN - everything else seems to work, except this. Any help appreciated