Yes it will need a route via the management interface so add a gateway if one doesn't exist and set it default.

@stephenw10 awesome, will do! Thank you kindly!

@stephenw10 Hey ya I did not test it long as my old home pfsense router failed I brought this one online quickly and did consecutive updates to the latest at 23 though I did look at the screen and all seemed normal at 24 all seems normal at boot normal menus but after some hours this showed up. Again all seems normal network side and you confirmed this just has to do with the monitor/hdmi hot swap so not too worried now.

Looks like you also have LLDP and ntopng. Are those enabled? If it's exactly every hour I'd look at the crontab and see what's being triggered. Or just at the system logs which should show cronjobs being fired.

@stephenw10 Thank you for your help. The Quality graph is exactly what I was looking for!

@stephenw10 @Gertjan thanks, I found that the problem is an hardware problem. I will open a new case about backup and restore. see you later :) Mauro

@stephenw10 thanks for the support! @JonathanLee said in Netgate 2100 inexplicable slow internet problem: What’s your MTU set to? default 1500.. I also tried to lower it but without success

Not easily. Not as far as I know at least.

Ah so in Status > Interfaces? Not show the link speed/duplex is quite common for N-base speeds. Is i actually linked at 2.5G? What do the linl LEDs at either end show? What pfSense version are you running? What firmware version is on the NIC? As far as I know the X550-T is one of the few NICs that has been shown to link at 2.5/5G so I'd expect it to work.

We use UDP Broadcast Relay for SSDP control which in our experience, the other packages had difficulty handling.

@stephenw10 Ok, thanks

Yup, you don't need support to get the firmware images.

https://forum.netgate.com/topic/186556/how-to-run-pkg-upgrade-from-diagnostics-command-prompt/20 echo /etc/rc.initial >> ~/.tcshrc.local

Strange, it was doing it middle of the night, no one was using internet or was logged in to the firewall.... No errors sice then, all seems to be good

@dotgate I'll add a little on my own c) there is no problem activating these options (if the device allows it) https://docs.netgate.com/pfsense/en/latest/hardware/cryptographic-accelerators.html https://man.freebsd.org/cgi/man.cgi?qat however, version 2.7.2 does not include the core modules of the QAT driver (Intel QuickAssist Technology (QAT) [Plus only]) But, if you build your Freebsd 14.0 kernel on any test device, you can download this driver manually into the PF kernel (by copying several files) [image: 1718133204206-1928c0d4-207f-4416-b8ac-1854b2e61e0c-image.png]

When you restore the config if should pull in any packages that were installed as long as it has access to the repo.

If you have a downstream (internal) router with other subnets behind it pfSense needs static route to those so it knows where to route traffic. https://docs.netgate.com/pfsense/en/latest/routing/static.html#example-static-route

@stephenw10 Thank you very much for your analysis and advice! With the configuration changes mentioned above, I no longer have pfsense blocking, it's a bit of a shame that some settings aren't more “original” configured for a (in my case) 8200. I'm glad to have found the https://forum.netgate.com/topic/182534/just-purchased-a-netgate-8200-having-a-few-issues/13topic which helped me enormously to find a solution to my problem. EDIT Last test [image: 1718113901940-16c681da-6cab-4ad6-b09e-d190ec1fad3f-image.png]