Thank for answer
Can you tell me how to block free proxy or anonymous proxy?

I won't be able to help out any further alexxtasi. You've exceeded my ability to assist through the forums. It's often difficult enough to get the base system running properly because of it's numerous bugs and quirks much less when you customize to the extent that you have. Good luck my friend.  :)

LOL,

never mind guys i have resolved this issue,

the problem as usual, was with the meat-ware .. rolls eyes

have a great day .. ;)

Cain

Hi ,

Thanks for your answer.

i had a sohpos asg 110/120 . i installed now on the same HW pfSense.

here are some information about network devices:

[2.1.4-RELEASE][root@c02506ccd392]/root(5): dmesg | grep pci
pcib0: <acpi host-pci="" bridge="">port 0xcf8-0xcff on acpi0
pci0: <acpi pci="" bus="">on pcib0
pcib1: <pci-pci bridge="">at device 1.0 on pci0
pci1: <pci bus="">on pcib1
vgapci0: <vga-compatible display="">mem 0xf4000000-0xf7ffffff,0xfb000000-0xfbffffff irq 16 at device 0.0 on pci1
fxp0: <intel 10="" 100="" 82559er="" embedded="" ethernet="">port 0xff00-0xff3f mem 0xfdfff000-0xfdffffff,0xfdf80000-0xfdf9ffff irq 16 at device 9.0 on pci0
fxp1: <intel 10="" 100="" 82559er="" embedded="" ethernet="">port 0xfe00-0xfe3f mem 0xfdffe000-0xfdffefff,0xfdfc0000-0xfdfdffff irq 16 at device 10.0 on pci0
fxp2: <intel 10="" 100="" 82559er="" embedded="" ethernet="">port 0xfd00-0xfd3f mem 0xfdffd000-0xfdffdfff,0xfdf60000-0xfdf7ffff irq 17 at device 11.0 on pci0
fxp3: <intel 10="" 100="" 82559er="" embedded="" ethernet="">port 0xfc00-0xfc3f mem 0xfdffc000-0xfdffcfff,0xfdfa0000-0xfdfbffff irq 17 at device 12.0 on pci0
atapci0: <via 6420="" sata150="" controller="">port 0xfb00-0xfb07,0xfa00-0xfa03,0xf900-0xf907,0xf800-0xf803,0xf700-0xf70f,0xf000-0xf0ff irq 20 at device 15.0 on pci0
atapci0: [ITHREAD]
ata2: <ata channel="">at channel 0 on atapci0
ata3: <ata channel="">at channel 1 on atapci0
uhci0: <via 83c572="" usb="" controller="">port 0xf600-0xf61f irq 21 at device 16.0 on pci0
uhci1: <via 83c572="" usb="" controller="">port 0xf500-0xf51f irq 21 at device 16.1 on pci0
uhci2: <via 83c572="" usb="" controller="">port 0xf400-0xf41f irq 21 at device 16.2 on pci0
uhci3: <via 83c572="" usb="" controller="">port 0xf300-0xf31f irq 21 at device 16.3 on pci0
ehci0: <via vt6202="" usb="" 2.0="" controller="">mem 0xfdffb000-0xfdffb0ff irq 21 at device 16.4 on pci0
isab0: <pci-isa bridge="">at device 17.0 on pci0

the trunk port is configured correctly and i can see also the traffic on the pfsense.

I can see just requests packets and when i dump on fxp0_vlan5 (Valn 5  interface) i can see that the pfsense didn't answer this traffic at all.

the firewall rules are set correctly and i am not seeing any blocks.

i have done test with the client as you suggest before i post my question .
in this case i have the same issue.

perhaps i miss some configuration.

could you please send me your sysctl -a output ?</pci-isa></via></via></via></via></via></ata></ata></via></intel></intel></intel></intel></vga-compatible></pci></pci-pci></acpi></acpi>

I have no idea how you would even calculate how much time is spent on something like Youtube. There is almost no correlation between bandwidth used or time spent transferring and actual viewing time.

The only practical way is to just have time slots that allow/block the services.

Otherwise you may have to do parenting the old fashioned way.

Hi Steve,
thank you, I uninstalled pfBlocker and now it runs better. But there are also some killed services from time to time. I now ordered a new APU board with 2GB RAM, a faster CPU and a 16 GB SSD. Then I should have enough memory and the possibility to swap on the disk.
Thank you for your support,
Regards

@zohaib where you able to resolve the issue? Having the same problem.

Sorry to pile on, but I'm looking at the same problem. 
I want a SPAN port, mirrored off my DMZ port, but I am unable to create the SPAN because it wont let me bridge a single port(DMZ).  Is there a better way to accomplish this?

I'm thinking I might tinker with the vSwitch and this pfsense is running on ESXi, but I would like to understand how/if pfsense can SPAN a single port not a bridge.  Thanks.

It's pretty straight forward really. Add an extra virtual NIC to the pfSense VM. Now assign that as a new interface in pfSense, it will be named OPT1 but rename it as you wish. Set the subnet/mask etc. Add DHCP if you want to use that. There will be no firewall rules on the new interface so all traffic will be blocked. Add appropriate rules to allow/restrict access to/from your server.

Steve

Sorry to bump this back to the top, but I'm still having this issue, and it's also happening on a new APU 1.C board running the latest version of pfSense.

If I cannot resolve this issue, I would like to at least know when a pfSense box is rebooted, is there a way I can be notified of a reboot? Sendmail? What about having the pfSense box open a url on my website, which I can code to notify me that it's been opened etc etc?

The 'files' package allows you to store custom scripts within the config file such that they would be reinstated after a firmware upgrade. You can only store text based files though so no images or binaries.
You may be able to store images in /conf , the config slice, and then point at them in the theme instead. I'm not sure I've never tried any theming.

Steve

Thanks for your advice. 
The ISP is allocating the private range of IP for each connect and I believed they did some routing or "something" within
country and within different ISP so that everyone can reach this private IP but not outside the country.

Questions.
1.  Is there anywhere I can change the pfsense behavior with custom configuration?
2.  If #1 is impossible, is there anyway I can run a cron to update via script manually
        or which php script file in pfsense  that I can change to submit only this private IP?

Well oddly enough I solved it by

rm /var/log/*.log then restarting the fw

I hadn't seen it. I guess I am only as good as the search terms I use. :(
Thanks for the link.

Jim

Ok, solved it by resetting the firefox profile… clears all my addons and stuff, but works now.

alt + f, navigate to Help > Troubleshooting Information then click the Reset Firefox button.

Best regards,

V

@jimp:

Do you have any packages installed on the system?
If not, for curiosity's sake, does that error go away if you install one (something small like Cron would be sufficient)

Hello,
I did what Jimp suggested and it works fine. The Services Dashboard is now properly displayed.
Thank You.

Does the checkbox at the bottom of this screenshot not do what you want?