NICs "Dead" After Install
-
@XIII I've got it connected directly at the moment, will find a switch to see if fxp0 and fxp1 require it, though fxp2 and fxp3 work fine directly connected.
@wallabybob Here's the dmesg output.
Copyright (c) 1992-2009 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. FreeBSD is a registered trademark of The FreeBSD Foundation. FreeBSD 8.0-RELEASE-p2 #0: Fri Jan 8 02:14:48 EST 2010 sullrich@FreeBSD_8.0_pfSense_2.0-snaps.pfsense.org:/usr/obj.pfSense/usr/pfSensesrc/src/sys/pfSense_wrap.8.i386 Timecounter "i8254" frequency 1193182 Hz quality 0 CPU: Intel(R) Celeron(R) M processor 1.50GHz (1499.83-MHz 686-class CPU) Origin = "GenuineIntel" Id = 0x6d8 Stepping = 8 Features=0xafe9fbff <fpu,vme,de,pse,tsc,msr,pae,mce,cx8,apic,sep,mtrr,pge,mca,cmov,pat,clflush,dts,acpi,mmx,fxsr,sse,sse2,ss,tm,pbe>real memory = 536870912 (512 MB) avail memory = 510476288 (486 MB) wlan: mac acl policy registered ACPI Error: A valid RSDP was not found 20090521 tbxfroot-309 ACPI: Table initialisation failed: AE_NOT_FOUND ACPI: Try disabling either ACPI or apic support. cryptosoft0: <software crypto="">on motherboard padlock0: No ACE support. pcib0: <host to="" pci="" bridge="">pcibus 0 on motherboard pir0: <pci 10="" interrupt="" routing="" table:="" entries="">on motherboard pci0: <pci bus="">on pcib0 pci0: <base peripheral=""> at device 0.1 (no driver attached) pci0: <base peripheral=""> at device 0.3 (no driver attached) vgapci0: <vga-compatible display="">port 0xe200-0xe207 mem 0xd8000000-0xdfffffff,0xe8180000-0xe81fffff irq 12 at device 2.0 on pci0 vgapci1: <vga-compatible display="">mem 0xe0000000-0xe7ffffff,0xe8100000-0xe817ffff at device 2.1 on pci0 uhci0: <intel 82801db="" (ich4)="" usb="" controller="" usb-a="">port 0xe000-0xe01f irq 12 at device 29.0 on pci0 uhci0: [ITHREAD] uhci0: LegSup = 0x2f00 usbus0: <intel 82801db="" (ich4)="" usb="" controller="" usb-a="">on uhci0 uhci1: <intel 82801db="" (ich4)="" usb="" controller="" usb-b="">port 0xe100-0xe11f irq 5 at device 29.1 on pci0 uhci1: [ITHREAD] uhci1: LegSup = 0x2f00 usbus1: <intel 82801db="" (ich4)="" usb="" controller="" usb-b="">on uhci1 ehci0: <intel 82801db="" l="" m="" (ich4)="" usb="" 2.0="" controller="">mem 0xe8200000-0xe82003ff irq 9 at device 29.7 on pci0 ehci0: [ITHREAD] usbus2: EHCI version 1.0 usbus2: <intel 82801db="" l="" m="" (ich4)="" usb="" 2.0="" controller="">on ehci0 pcib1: <pcibios pci-pci="" bridge="">at device 30.0 on pci0 pci1: <pci bus="">on pcib1 fxp0: <intel 100="" 82551="" pro="" ethernet="">port 0xd000-0xd03f mem 0xe8083000-0xe8083fff,0xe8000000-0xe801ffff irq 12 at device 4.0 on pci1 miibus0: <mii bus="">on fxp0 inphy0: <i82555 10="" 100="" media="" interface="">PHY 1 on miibus0 inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto fxp0: [ITHREAD] fxp1: <intel 100="" 82551="" pro="" ethernet="">port 0xd100-0xd13f mem 0xe8081000-0xe8081fff,0xe8020000-0xe803ffff irq 10 at device 5.0 on pci1 miibus1: <mii bus="">on fxp1 inphy1: <i82555 10="" 100="" media="" interface="">PHY 1 on miibus1 inphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto fxp1: [ITHREAD] fxp2: <intel 100="" 82551="" pro="" ethernet="">port 0xd200-0xd23f mem 0xe8080000-0xe8080fff,0xe8040000-0xe805ffff irq 11 at device 6.0 on pci1 miibus2: <mii bus="">on fxp2 inphy2: <i82555 10="" 100="" media="" interface="">PHY 1 on miibus2 inphy2: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto fxp2: [ITHREAD] fxp3: <intel 100="" 82551="" pro="" ethernet="">port 0xd300-0xd33f mem 0xe8082000-0xe8082fff,0xe8060000-0xe807ffff irq 5 at device 7.0 on pci1 miibus3: <mii bus="">on fxp3 inphy3: <i82555 10="" 100="" media="" interface="">PHY 1 on miibus3 inphy3: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto fxp3: [ITHREAD] isab0: <pci-isa bridge="">at device 31.0 on pci0 isa0: <isa bus="">on isab0 atapci0: <intel ich4="" udma100="" controller="">port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xf000-0xf00f at device 31.1 on pci0 ata0: <ata 0="" channel="">on atapci0 ata0: [ITHREAD] ata1: <ata 1="" channel="">on atapci0 ata1: [ITHREAD] pci0: <serial bus,="" smbus="">at device 31.3 (no driver attached) cpu0 on motherboard atrtc0: <at realtime="" clock="">at port 0x70-0x71 irq 8 pnpid PNP0b00 on isa0 unknown: <pnp0c01>can't assign resources (memory) uart0: <16550 or compatible> at port 0x3f8-0x3ff irq 4 flags 0x10 pnpid PNP0501 on isa0 uart0: [FILTER] uart0: console (9600,n,8,1) uart1: <16550 or compatible> at port 0x2f8-0x2ff irq 3 pnpid PNP0501 on isa0 uart1: [FILTER] orm0: <isa option="" roms="">at iomem 0xc0000-0xcc7ff,0xd0000-0xd17ff pnpid ORM0000 on isa0 ppc0: parallel port not found. unknown: <pnp0c01>can't assign resources (memory) Timecounter "TSC" frequency 1499834836 Hz quality 800 Timecounters tick every 10.000 msec IPsec: Initialized Security Association Processing. usbus0: 12Mbps Full Speed USB v1.0 usbus1: 12Mbps Full Speed USB v1.0 ugen0.1: <intel>at usbus0 uhub0: <intel 1="" 9="" uhci="" root="" hub,="" class="" 0,="" rev="" 1.00="" 1.00,="" addr="">on usbus0 ugen1.1: <intel>at usbus1 uhub1: <intel 1="" 9="" uhci="" root="" hub,="" class="" 0,="" rev="" 1.00="" 1.00,="" addr="">on usbus1 usbus2: 480Mbps High Speed USB v2.0 ad0: DMA limited to UDMA33, controller found non-ATA66 cable ugen2.1: <intel>at usbus2 uhub2: <intel 1="" 9="" ehci="" root="" hub,="" class="" 0,="" rev="" 2.00="" 1.00,="" addr="">on usbus2 ad0: 57231MB <hts721060g9at00 mc3oa51a="">at ata0-master UDMA33 uhub0: 2 ports with 2 removable, self powered uhub1: 2 ports with 2 removable, self powered GEOM: ad0s1: geometry does not match label (255h,63s != 16h,63s). Root mount waiting for: usbus2 Root mount waiting for: usbus2 uhub2: 4 ports with 4 removable, self powered Trying to mount root from ufs:/dev/ad0s1a pflog0: promiscuous mode enabled fxp2: link state changed to UP fxp3: link state changed to UP fxp2: link state changed to DOWN fxp2: link state changed to UP</hts721060g9at00></intel></intel></intel></intel></intel></intel></pnp0c01></isa></pnp0c01></at></serial></ata></ata></intel></isa></pci-isa></i82555></mii></intel></i82555></mii></intel></i82555></mii></intel></i82555></mii></intel></pci></pcibios></intel></intel></intel></intel></intel></intel></vga-compatible></vga-compatible></pci></pci></host></software></fpu,vme,de,pse,tsc,msr,pae,mce,cx8,apic,sep,mtrr,pge,mca,cmov,pat,clflush,dts,acpi,mmx,fxsr,sse,sse2,ss,tm,pbe> -
if tis to a modem its fine, if the others show up as fine when directly connected, one of the nics support auto crossover.
disable acpi and see what happens, that output says its not supported on the device.:
ACPI Error: A valid RSDP was not found 20090521 tbxfroot-309
ACPI: Table initialisation failed: AE_NOT_FOUND
ACPI: Try disabling either ACPI or apic support. -
@XIII I've got ACPI disabled in the BIOS and during boot-up I've been choosing the option without ACPI. Is there something else I should be doing?
-
will have to wait for wallabybob as he requested the dmesg, i dont know how to read all of it.
doesnt look like acpi is being properly disabled -
@XIII Here's a new dmesg when I enable PnP and ACPI in the BIOS, just in case that helps.
Copyright (c) 1992-2009 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. FreeBSD is a registered trademark of The FreeBSD Foundation. FreeBSD 8.0-RELEASE-p2 #0: Fri Jan 8 02:14:48 EST 2010 sullrich@FreeBSD_8.0_pfSense_2.0-snaps.pfsense.org:/usr/obj.pfSense/usr/pfSensesrc/src/sys/pfSense_wrap.8.i386 Timecounter "i8254" frequency 1193182 Hz quality 0 CPU: Intel(R) Celeron(R) M processor 1.50GHz (1499.84-MHz 686-class CPU) Origin = "GenuineIntel" Id = 0x6d8 Stepping = 8 Features=0xafe9fbff <fpu,vme,de,pse,tsc,msr,pae,mce,cx8,apic,sep,mtrr,pge,mca,cmov,pat,clflush,dts,acpi,mmx,fxsr,sse,sse2,ss,tm,pbe>real memory = 536870912 (512 MB) avail memory = 510414848 (486 MB) wlan: mac acl policy registered cryptosoft0: <software crypto="">on motherboard padlock0: No ACE support. acpi0: <intelr awrdacpi="">on motherboard acpi0: [ITHREAD] acpi0: Power Button (fixed) acpi0: reservation of 0, a0000 (3) failed acpi0: reservation of 100000, 1fdf0000 (3) failed Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000 acpi_timer0: <24-bit timer at 3.579545MHz> port 0x408-0x40b on acpi0 acpi_button0: <power button="">on acpi0 pcib0: <acpi host-pci="" bridge="">port 0xcf8-0xcff on acpi0 pci0: <acpi pci="" bus="">on pcib0 pci0: <base peripheral=""> at device 0.1 (no driver attached) pci0: <base peripheral=""> at device 0.3 (no driver attached) vgapci0: <vga-compatible display="">port 0xe200-0xe207 mem 0xd8000000-0xdfffffff,0xe8180000-0xe81fffff irq 12 at device 2.0 on pci0 vgapci1: <vga-compatible display="">mem 0xe0000000-0xe7ffffff,0xe8100000-0xe817ffff at device 2.1 on pci0 uhci0: <intel 82801db="" (ich4)="" usb="" controller="" usb-a="">port 0xe000-0xe01f irq 12 at device 29.0 on pci0 uhci0: [ITHREAD] uhci0: LegSup = 0x2f00 usbus0: <intel 82801db="" (ich4)="" usb="" controller="" usb-a="">on uhci0 uhci1: <intel 82801db="" (ich4)="" usb="" controller="" usb-b="">port 0xe100-0xe11f irq 5 at device 29.1 on pci0 uhci1: [ITHREAD] uhci1: LegSup = 0x2f00 usbus1: <intel 82801db="" (ich4)="" usb="" controller="" usb-b="">on uhci1 ehci0: <intel 82801db="" l="" m="" (ich4)="" usb="" 2.0="" controller="">mem 0xe8200000-0xe82003ff irq 7 at device 29.7 on pci0 ehci0: [ITHREAD] usbus2: EHCI version 1.0 usbus2: <intel 82801db="" l="" m="" (ich4)="" usb="" 2.0="" controller="">on ehci0 pcib1: <acpi pci-pci="" bridge="">at device 30.0 on pci0 pci1: <acpi pci="" bus="">on pcib1 fxp0: <intel 100="" 82551="" pro="" ethernet="">port 0xd000-0xd03f mem 0xe8083000-0xe8083fff,0xe8000000-0xe801ffff irq 12 at device 4.0 on pci1 miibus0: <mii bus="">on fxp0 inphy0: <i82555 10="" 100="" media="" interface="">PHY 1 on miibus0 inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto fxp0: [ITHREAD] fxp1: <intel 100="" 82551="" pro="" ethernet="">port 0xd100-0xd13f mem 0xe8081000-0xe8081fff,0xe8020000-0xe803ffff irq 10 at device 5.0 on pci1 miibus1: <mii bus="">on fxp1 inphy1: <i82555 10="" 100="" media="" interface="">PHY 1 on miibus1 inphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto fxp1: [ITHREAD] fxp2: <intel 100="" 82551="" pro="" ethernet="">port 0xd200-0xd23f mem 0xe8080000-0xe8080fff,0xe8040000-0xe805ffff irq 11 at device 6.0 on pci1 miibus2: <mii bus="">on fxp2 inphy2: <i82555 10="" 100="" media="" interface="">PHY 1 on miibus2 inphy2: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto fxp2: [ITHREAD] fxp3: <intel 100="" 82551="" pro="" ethernet="">port 0xd300-0xd33f mem 0xe8082000-0xe8082fff,0xe8060000-0xe807ffff irq 5 at device 7.0 on pci1 miibus3: <mii bus="">on fxp3 inphy3: <i82555 10="" 100="" media="" interface="">PHY 1 on miibus3 inphy3: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto fxp3: [ITHREAD] isab0: <pci-isa bridge="">at device 31.0 on pci0 isa0: <isa bus="">on isab0 atapci0: <intel ich4="" udma100="" controller="">port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xf000-0xf00f at device 31.1 on pci0 ata0: <ata 0="" channel="">on atapci0 ata0: [ITHREAD] ata1: <ata 1="" channel="">on atapci0 ata1: [ITHREAD] pci0: <serial bus,="" smbus="">at device 31.3 (no driver attached) acpi_tz0: <thermal zone="">on acpi0 atrtc0: <at realtime="" clock="">port 0x70-0x73 irq 8 on acpi0 uart0: <16550 or compatible> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0 uart0: [FILTER] uart0: console (9600,n,8,1) uart1: <16550 or compatible> port 0x2f8-0x2ff irq 3 on acpi0 uart1: [FILTER] cpu0: <acpi cpu="">on acpi0 acpi_throttle0: <acpi cpu="" throttling="">on cpu0 orm0: <isa option="" roms="">at iomem 0xc0000-0xcc7ff,0xd0000-0xd17ff pnpid ORM0000 on isa0 ppc0: parallel port not found. Timecounter "TSC" frequency 1499836051 Hz quality 800 Timecounters tick every 10.000 msec IPsec: Initialized Security Association Processing. usbus0: 12Mbps Full Speed USB v1.0 usbus1: 12Mbps Full Speed USB v1.0 ugen0.1: <intel>at usbus0 uhub0: <intel 1="" 9="" uhci="" root="" hub,="" class="" 0,="" rev="" 1.00="" 1.00,="" addr="">on usbus0 ugen1.1: <intel>at usbus1 uhub1: <intel 1="" 9="" uhci="" root="" hub,="" class="" 0,="" rev="" 1.00="" 1.00,="" addr="">on usbus1 usbus2: 480Mbps High Speed USB v2.0 ad0: DMA limited to UDMA33, controller found non-ATA66 cable ugen2.1: <intel>at usbus2 uhub2: <intel 1="" 9="" ehci="" root="" hub,="" class="" 0,="" rev="" 2.00="" 1.00,="" addr="">on usbus2 ad0: 57231MB <hts721060g9at00 mc3oa51a="">at ata0-master UDMA33 GEOM: ad0s1: geometry does not match label (255h,63s != 16h,63s). Root mount waiting for: usbus2 usbus1 usbus0 uhub0: 2 ports with 2 removable, self powered uhub1: 2 ports with 2 removable, self powered Root mount waiting for: usbus2 uhub2: 4 ports with 4 removable, self powered Trying to mount root from ufs:/dev/ad0s1a pflog0: promiscuous mode enabled</hts721060g9at00></intel></intel></intel></intel></intel></intel></isa></acpi></acpi></at></thermal></serial></ata></ata></intel></isa></pci-isa></i82555></mii></intel></i82555></mii></intel></i82555></mii></intel></i82555></mii></intel></acpi></acpi></intel></intel></intel></intel></intel></intel></vga-compatible></vga-compatible></acpi></acpi></power></intelr></software></fpu,vme,de,pse,tsc,msr,pae,mce,cx8,apic,sep,mtrr,pge,mca,cmov,pat,clflush,dts,acpi,mmx,fxsr,sse,sse2,ss,tm,pbe> -
this is in the wrong forum, you are using 2.0 ALPHA
try a 1.2.3 release version, if that solves it post a thread in 2.02.0 is for testing only its not stable 1.2.3 is.
-
@XIII As I noted above, 1.2.3 ignores the console after boot, but if I need to get the topic moved over to another forum that's fine too. I still need to figure out if this is hardware or software causing the issue.
EDIT: Attempting to get 1.2.3 installed properly through some BIOS nonsense, will list results in a tic.
-
1.2.2?
did you try 1.2.3 with the method i stated?
since you used 1.2.3 and it looks like all 4 nics are the one i would say they are bad.try to make them wan/lan instead of opt if that still doesnt work they may be bad. did the person who gave it to you say everything was working?
-
@XIII Sadly all I can get from the guy who gave it to me is that "it was working when I used it last" which tells me a whole lot of nothing. I got 1.2.3 working through some blind keyboard magic. Here's the new dmesg output (ACPI enabled)
Copyright (c) 1992-2009 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. FreeBSD is a registered trademark of The FreeBSD Foundation. FreeBSD 7.2-RELEASE-p5 #0: Sun Dec 6 23:05:10 EST 2009 sullrich@FreeBSD_7.2_pfSense_1.2.3_snaps.pfsense.org:/usr/obj.pfSense/usr/pfSensesrc/src/sys/pfSense_wrap.7.i386 Timecounter "i8254" frequency 1193182 Hz quality 0 CPU: Intel(R) Celeron(R) M processor 1.50GHz (1499.84-MHz 686-class CPU) Origin = "GenuineIntel" Id = 0x6d8 Stepping = 8 Features=0xafe9fbff <fpu,vme,de,pse,tsc,msr,pae,mce,cx8,apic,sep,mtrr,pge,mca,cmov,pat,clflush,dts,acpi,mmx,fxsr,sse,sse2,ss,tm,pbe>real memory = 535756800 (510 MB) avail memory = 510386176 (486 MB) wlan: mac acl policy registered cryptosoft0: <software crypto="">on motherboard padlock0: No ACE support. acpi0: <intelr awrdacpi="">on motherboard acpi0: [ITHREAD] acpi0: Power Button (fixed) acpi0: reservation of 0, a0000 (3) failed acpi0: reservation of 100000, 1fdf0000 (3) failed Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000 acpi_timer0: <24-bit timer at 3.579545MHz> port 0x408-0x40b on acpi0 acpi_button0: <power button="">on acpi0 pcib0: <acpi host-pci="" bridge="">port 0xcf8-0xcff on acpi0 pci0: <acpi pci="" bus="">on pcib0 pci0: <base peripheral=""> at device 0.1 (no driver attached) pci0: <base peripheral=""> at device 0.3 (no driver attached) vgapci0: <vga-compatible display="">port 0xe200-0xe207 mem 0xd8000000-0xdfffffff,0xe8180000-0xe81fffff irq 12 at device 2.0 on pci0 vgapci1: <vga-compatible display="">mem 0xe0000000-0xe7ffffff,0xe8100000-0xe817ffff at device 2.1 on pci0 uhci0: <intel 82801db="" (ich4)="" usb="" controller="" usb-a="">port 0xe000-0xe01f irq 12 at device 29.0 on pci0 uhci0: [GIANT-LOCKED] uhci0: [ITHREAD] usb0: <intel 82801db="" (ich4)="" usb="" controller="" usb-a="">on uhci0 usb0: USB revision 1.0 uhub0: <intel 1="" 9="" uhci="" root="" hub,="" class="" 0,="" rev="" 1.00="" 1.00,="" addr="">on usb0 uhub0: 2 ports with 2 removable, self powered uhci1: <intel 82801db="" (ich4)="" usb="" controller="" usb-b="">port 0xe100-0xe11f irq 5 at device 29.1 on pci0 uhci1: [GIANT-LOCKED] uhci1: [ITHREAD] usb1: <intel 82801db="" (ich4)="" usb="" controller="" usb-b="">on uhci1 usb1: USB revision 1.0 uhub1: <intel 1="" 9="" uhci="" root="" hub,="" class="" 0,="" rev="" 1.00="" 1.00,="" addr="">on usb1 uhub1: 2 ports with 2 removable, self powered ehci0: <intel 82801db="" l="" m="" (ich4)="" usb="" 2.0="" controller="">mem 0xe8200000-0xe82003ff irq 7 at device 29.7 on pci0 ehci0: [GIANT-LOCKED] ehci0: [ITHREAD] usb2: EHCI version 1.0 usb2: companion controllers, 2 ports each: usb0 usb1 usb2: <intel 82801db="" l="" m="" (ich4)="" usb="" 2.0="" controller="">on ehci0 usb2: USB revision 2.0 uhub2: <intel 1="" 9="" ehci="" root="" hub,="" class="" 0,="" rev="" 2.00="" 1.00,="" addr="">on usb2 uhub2: 4 ports with 4 removable, self powered pcib1: <acpi pci-pci="" bridge="">at device 30.0 on pci0 pci1: <acpi pci="" bus="">on pcib1 fxp0: <intel 100="" 82551="" pro="" ethernet="">port 0xd000-0xd03f mem 0xe8083000-0xe8083fff,0xe8000000-0xe801ffff irq 12 at device 4.0 on pci1 miibus0: <mii bus="">on fxp0 inphy0: <i82555 10="" 100="" media="" interface="">PHY 1 on miibus0 inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto fxp0: Ethernet address: 00:0e:b6:8c:44:a0 fxp0: [ITHREAD] fxp1: <intel 100="" 82551="" pro="" ethernet="">port 0xd100-0xd13f mem 0xe8081000-0xe8081fff,0xe8020000-0xe803ffff irq 10 at device 5.0 on pci1 miibus1: <mii bus="">on fxp1 inphy1: <i82555 10="" 100="" media="" interface="">PHY 1 on miibus1 inphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto fxp1: Ethernet address: 00:0e:b6:8c:44:a1 fxp1: [ITHREAD] fxp2: <intel 100="" 82551="" pro="" ethernet="">port 0xd200-0xd23f mem 0xe8080000-0xe8080fff,0xe8040000-0xe805ffff irq 11 at device 6.0 on pci1 miibus2: <mii bus="">on fxp2 inphy2: <i82555 10="" 100="" media="" interface="">PHY 1 on miibus2 inphy2: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto fxp2: Ethernet address: 00:0e:b6:2b:c2:e9 fxp2: [ITHREAD] fxp3: <intel 100="" 82551="" pro="" ethernet="">port 0xd300-0xd33f mem 0xe8082000-0xe8082fff,0xe8060000-0xe807ffff irq 5 at device 7.0 on pci1 miibus3: <mii bus="">on fxp3 inphy3: <i82555 10="" 100="" media="" interface="">PHY 1 on miibus3 inphy3: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto fxp3: Ethernet address: 00:0e:b6:2b:c2:e8 fxp3: [ITHREAD] isab0: <pci-isa bridge="">at device 31.0 on pci0 isa0: <isa bus="">on isab0 atapci0: <intel ich4="" udma100="" controller="">port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xf000-0xf00f at device 31.1 on pci0 ata0: <ata 0="" channel="">on atapci0 ata0: [ITHREAD] ata1: <ata 1="" channel="">on atapci0 ata1: [ITHREAD] pci0: <serial bus,="" smbus="">at device 31.3 (no driver attached) acpi_tz0: <thermal zone="">on acpi0 speaker0: <pc speaker="">port 0x61 on acpi0 sio0: <16550A-compatible COM port> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0 sio0: type 16550A, console sio0: [FILTER] sio1: <16550A-compatible COM port> port 0x2f8-0x2ff irq 3 on acpi0 sio1: type 16550A sio1: [FILTER] cpu0: <acpi cpu="">on acpi0 acpi_throttle0: <acpi cpu="" throttling="">on cpu0 orm0: <isa option="" roms="">at iomem 0xc0000-0xcc7ff,0xd0000-0xd17ff pnpid ORM0000 on isa0 ppc0: parallel port not found. Timecounter "TSC" frequency 1499835835 Hz quality 800 Timecounters tick every 10.000 msec IPsec: Initialized Security Association Processing. ad0: DMA limited to UDMA33, controller found non-ATA66 cable ad0: 57231MB <hts721060g9at00 mc3oa51a="">at ata0-master UDMA33 Trying to mount root from ufs:/dev/ad0s1a pflog0: promiscuous mode enabled</hts721060g9at00></isa></acpi></acpi></pc></thermal></serial></ata></ata></intel></isa></pci-isa></i82555></mii></intel></i82555></mii></intel></i82555></mii></intel></i82555></mii></intel></acpi></acpi></intel></intel></intel></intel></intel></intel></intel></intel></intel></vga-compatible></vga-compatible></acpi></acpi></power></intelr></software></fpu,vme,de,pse,tsc,msr,pae,mce,cx8,apic,sep,mtrr,pge,mca,cmov,pat,clflush,dts,acpi,mmx,fxsr,sse,sse2,ss,tm,pbe> -
Assigning fxp0 and fxp1 as LAN/WAN doesn't change them at all, still no link lights. Starting to look more and more like hardware I guess.
EDIT: On a whim I bridged fxp0 and fxp1 to fxp3 (LAN) to see if that would help, now it lists their status as "no carrier" instead of "down."
-
ok, do you need 4 ports? do they work with the factory riverbed image?
-
I don't need four, though it'd be nice, as for the factory image it wouldn't do much because the license had expired. I didn't think to test all the ports before reformatting because it seemed like a given that they'd work. Obviously I had too much faith in the technology.
-
so no way to get factory image (your using that drive?)
-
it looks like pf sees all 4 nics, and that all 4 are the same type.
did the guy who gave it to you use just the 2 that you got working? -
make sure everything is clean, ive had some lint/dust stop a device from working, i blew on it with air all over and looked at it very carefully for about 5 min to see if i missed anything, it fixed the problem
if all else fails its a 1.5 GHZ system with two 1 Gbps nics (working) but since the nics are Gbps i wouldnt use it for pf (unless you have a fiber connection) i would use it for freenas or the like.
-
Can't do a factory restore as I'm using the drive. It's a tiny little box which is why I was going to use it as a firewall, but I could see possibly using it for FreeNAS or such as well. The guy who gave it to me hadn't used it a long time, though he says he only ever used two ports so it's possible it's always had two dead ones. I suppose if nothing else it's running at the moment and has enough active ports to route if I needed it to.
Still, if there are any brainstorms on the other two ports I'd certainly appreciate the input. Thanks @XIII for all the suggestions.
-
Assigning fxp0 and fxp1 their own static addresses also gives the status "no carrier". Not 100% sure what that means though.
-
wallabybob may be able to decipher more from the dmesg than i could so he may respond (thought i saw him "making his rounds", also he was the one who thought of that)
hope it works out
the no carrier means no connection
-
Got'cha, hopefully he can shed some light on this, if not I've got a mostly working machine and a few new tricks for installing embedded. Thanks XIII.
-
your welcome, I try when I can (or think I can)
Copyright 2025 Rubicon Communications LLC (Netgate). All rights reserved.