NICs "Dead" After Install
-
@XIII I've got ACPI disabled in the BIOS and during boot-up I've been choosing the option without ACPI. Is there something else I should be doing?
-
will have to wait for wallabybob as he requested the dmesg, i dont know how to read all of it.
doesnt look like acpi is being properly disabled -
@XIII Here's a new dmesg when I enable PnP and ACPI in the BIOS, just in case that helps.
Copyright (c) 1992-2009 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. FreeBSD is a registered trademark of The FreeBSD Foundation. FreeBSD 8.0-RELEASE-p2 #0: Fri Jan 8 02:14:48 EST 2010 sullrich@FreeBSD_8.0_pfSense_2.0-snaps.pfsense.org:/usr/obj.pfSense/usr/pfSensesrc/src/sys/pfSense_wrap.8.i386 Timecounter "i8254" frequency 1193182 Hz quality 0 CPU: Intel(R) Celeron(R) M processor 1.50GHz (1499.84-MHz 686-class CPU) Origin = "GenuineIntel" Id = 0x6d8 Stepping = 8 Features=0xafe9fbff <fpu,vme,de,pse,tsc,msr,pae,mce,cx8,apic,sep,mtrr,pge,mca,cmov,pat,clflush,dts,acpi,mmx,fxsr,sse,sse2,ss,tm,pbe>real memory = 536870912 (512 MB) avail memory = 510414848 (486 MB) wlan: mac acl policy registered cryptosoft0: <software crypto="">on motherboard padlock0: No ACE support. acpi0: <intelr awrdacpi="">on motherboard acpi0: [ITHREAD] acpi0: Power Button (fixed) acpi0: reservation of 0, a0000 (3) failed acpi0: reservation of 100000, 1fdf0000 (3) failed Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000 acpi_timer0: <24-bit timer at 3.579545MHz> port 0x408-0x40b on acpi0 acpi_button0: <power button="">on acpi0 pcib0: <acpi host-pci="" bridge="">port 0xcf8-0xcff on acpi0 pci0: <acpi pci="" bus="">on pcib0 pci0: <base peripheral=""> at device 0.1 (no driver attached) pci0: <base peripheral=""> at device 0.3 (no driver attached) vgapci0: <vga-compatible display="">port 0xe200-0xe207 mem 0xd8000000-0xdfffffff,0xe8180000-0xe81fffff irq 12 at device 2.0 on pci0 vgapci1: <vga-compatible display="">mem 0xe0000000-0xe7ffffff,0xe8100000-0xe817ffff at device 2.1 on pci0 uhci0: <intel 82801db="" (ich4)="" usb="" controller="" usb-a="">port 0xe000-0xe01f irq 12 at device 29.0 on pci0 uhci0: [ITHREAD] uhci0: LegSup = 0x2f00 usbus0: <intel 82801db="" (ich4)="" usb="" controller="" usb-a="">on uhci0 uhci1: <intel 82801db="" (ich4)="" usb="" controller="" usb-b="">port 0xe100-0xe11f irq 5 at device 29.1 on pci0 uhci1: [ITHREAD] uhci1: LegSup = 0x2f00 usbus1: <intel 82801db="" (ich4)="" usb="" controller="" usb-b="">on uhci1 ehci0: <intel 82801db="" l="" m="" (ich4)="" usb="" 2.0="" controller="">mem 0xe8200000-0xe82003ff irq 7 at device 29.7 on pci0 ehci0: [ITHREAD] usbus2: EHCI version 1.0 usbus2: <intel 82801db="" l="" m="" (ich4)="" usb="" 2.0="" controller="">on ehci0 pcib1: <acpi pci-pci="" bridge="">at device 30.0 on pci0 pci1: <acpi pci="" bus="">on pcib1 fxp0: <intel 100="" 82551="" pro="" ethernet="">port 0xd000-0xd03f mem 0xe8083000-0xe8083fff,0xe8000000-0xe801ffff irq 12 at device 4.0 on pci1 miibus0: <mii bus="">on fxp0 inphy0: <i82555 10="" 100="" media="" interface="">PHY 1 on miibus0 inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto fxp0: [ITHREAD] fxp1: <intel 100="" 82551="" pro="" ethernet="">port 0xd100-0xd13f mem 0xe8081000-0xe8081fff,0xe8020000-0xe803ffff irq 10 at device 5.0 on pci1 miibus1: <mii bus="">on fxp1 inphy1: <i82555 10="" 100="" media="" interface="">PHY 1 on miibus1 inphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto fxp1: [ITHREAD] fxp2: <intel 100="" 82551="" pro="" ethernet="">port 0xd200-0xd23f mem 0xe8080000-0xe8080fff,0xe8040000-0xe805ffff irq 11 at device 6.0 on pci1 miibus2: <mii bus="">on fxp2 inphy2: <i82555 10="" 100="" media="" interface="">PHY 1 on miibus2 inphy2: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto fxp2: [ITHREAD] fxp3: <intel 100="" 82551="" pro="" ethernet="">port 0xd300-0xd33f mem 0xe8082000-0xe8082fff,0xe8060000-0xe807ffff irq 5 at device 7.0 on pci1 miibus3: <mii bus="">on fxp3 inphy3: <i82555 10="" 100="" media="" interface="">PHY 1 on miibus3 inphy3: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto fxp3: [ITHREAD] isab0: <pci-isa bridge="">at device 31.0 on pci0 isa0: <isa bus="">on isab0 atapci0: <intel ich4="" udma100="" controller="">port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xf000-0xf00f at device 31.1 on pci0 ata0: <ata 0="" channel="">on atapci0 ata0: [ITHREAD] ata1: <ata 1="" channel="">on atapci0 ata1: [ITHREAD] pci0: <serial bus,="" smbus="">at device 31.3 (no driver attached) acpi_tz0: <thermal zone="">on acpi0 atrtc0: <at realtime="" clock="">port 0x70-0x73 irq 8 on acpi0 uart0: <16550 or compatible> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0 uart0: [FILTER] uart0: console (9600,n,8,1) uart1: <16550 or compatible> port 0x2f8-0x2ff irq 3 on acpi0 uart1: [FILTER] cpu0: <acpi cpu="">on acpi0 acpi_throttle0: <acpi cpu="" throttling="">on cpu0 orm0: <isa option="" roms="">at iomem 0xc0000-0xcc7ff,0xd0000-0xd17ff pnpid ORM0000 on isa0 ppc0: parallel port not found. Timecounter "TSC" frequency 1499836051 Hz quality 800 Timecounters tick every 10.000 msec IPsec: Initialized Security Association Processing. usbus0: 12Mbps Full Speed USB v1.0 usbus1: 12Mbps Full Speed USB v1.0 ugen0.1: <intel>at usbus0 uhub0: <intel 1="" 9="" uhci="" root="" hub,="" class="" 0,="" rev="" 1.00="" 1.00,="" addr="">on usbus0 ugen1.1: <intel>at usbus1 uhub1: <intel 1="" 9="" uhci="" root="" hub,="" class="" 0,="" rev="" 1.00="" 1.00,="" addr="">on usbus1 usbus2: 480Mbps High Speed USB v2.0 ad0: DMA limited to UDMA33, controller found non-ATA66 cable ugen2.1: <intel>at usbus2 uhub2: <intel 1="" 9="" ehci="" root="" hub,="" class="" 0,="" rev="" 2.00="" 1.00,="" addr="">on usbus2 ad0: 57231MB <hts721060g9at00 mc3oa51a="">at ata0-master UDMA33 GEOM: ad0s1: geometry does not match label (255h,63s != 16h,63s). Root mount waiting for: usbus2 usbus1 usbus0 uhub0: 2 ports with 2 removable, self powered uhub1: 2 ports with 2 removable, self powered Root mount waiting for: usbus2 uhub2: 4 ports with 4 removable, self powered Trying to mount root from ufs:/dev/ad0s1a pflog0: promiscuous mode enabled</hts721060g9at00></intel></intel></intel></intel></intel></intel></isa></acpi></acpi></at></thermal></serial></ata></ata></intel></isa></pci-isa></i82555></mii></intel></i82555></mii></intel></i82555></mii></intel></i82555></mii></intel></acpi></acpi></intel></intel></intel></intel></intel></intel></vga-compatible></vga-compatible></acpi></acpi></power></intelr></software></fpu,vme,de,pse,tsc,msr,pae,mce,cx8,apic,sep,mtrr,pge,mca,cmov,pat,clflush,dts,acpi,mmx,fxsr,sse,sse2,ss,tm,pbe> -
this is in the wrong forum, you are using 2.0 ALPHA
try a 1.2.3 release version, if that solves it post a thread in 2.02.0 is for testing only its not stable 1.2.3 is.
-
@XIII As I noted above, 1.2.3 ignores the console after boot, but if I need to get the topic moved over to another forum that's fine too. I still need to figure out if this is hardware or software causing the issue.
EDIT: Attempting to get 1.2.3 installed properly through some BIOS nonsense, will list results in a tic.
-
1.2.2?
did you try 1.2.3 with the method i stated?
since you used 1.2.3 and it looks like all 4 nics are the one i would say they are bad.try to make them wan/lan instead of opt if that still doesnt work they may be bad. did the person who gave it to you say everything was working?
-
@XIII Sadly all I can get from the guy who gave it to me is that "it was working when I used it last" which tells me a whole lot of nothing. I got 1.2.3 working through some blind keyboard magic. Here's the new dmesg output (ACPI enabled)
Copyright (c) 1992-2009 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. FreeBSD is a registered trademark of The FreeBSD Foundation. FreeBSD 7.2-RELEASE-p5 #0: Sun Dec 6 23:05:10 EST 2009 sullrich@FreeBSD_7.2_pfSense_1.2.3_snaps.pfsense.org:/usr/obj.pfSense/usr/pfSensesrc/src/sys/pfSense_wrap.7.i386 Timecounter "i8254" frequency 1193182 Hz quality 0 CPU: Intel(R) Celeron(R) M processor 1.50GHz (1499.84-MHz 686-class CPU) Origin = "GenuineIntel" Id = 0x6d8 Stepping = 8 Features=0xafe9fbff <fpu,vme,de,pse,tsc,msr,pae,mce,cx8,apic,sep,mtrr,pge,mca,cmov,pat,clflush,dts,acpi,mmx,fxsr,sse,sse2,ss,tm,pbe>real memory = 535756800 (510 MB) avail memory = 510386176 (486 MB) wlan: mac acl policy registered cryptosoft0: <software crypto="">on motherboard padlock0: No ACE support. acpi0: <intelr awrdacpi="">on motherboard acpi0: [ITHREAD] acpi0: Power Button (fixed) acpi0: reservation of 0, a0000 (3) failed acpi0: reservation of 100000, 1fdf0000 (3) failed Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000 acpi_timer0: <24-bit timer at 3.579545MHz> port 0x408-0x40b on acpi0 acpi_button0: <power button="">on acpi0 pcib0: <acpi host-pci="" bridge="">port 0xcf8-0xcff on acpi0 pci0: <acpi pci="" bus="">on pcib0 pci0: <base peripheral=""> at device 0.1 (no driver attached) pci0: <base peripheral=""> at device 0.3 (no driver attached) vgapci0: <vga-compatible display="">port 0xe200-0xe207 mem 0xd8000000-0xdfffffff,0xe8180000-0xe81fffff irq 12 at device 2.0 on pci0 vgapci1: <vga-compatible display="">mem 0xe0000000-0xe7ffffff,0xe8100000-0xe817ffff at device 2.1 on pci0 uhci0: <intel 82801db="" (ich4)="" usb="" controller="" usb-a="">port 0xe000-0xe01f irq 12 at device 29.0 on pci0 uhci0: [GIANT-LOCKED] uhci0: [ITHREAD] usb0: <intel 82801db="" (ich4)="" usb="" controller="" usb-a="">on uhci0 usb0: USB revision 1.0 uhub0: <intel 1="" 9="" uhci="" root="" hub,="" class="" 0,="" rev="" 1.00="" 1.00,="" addr="">on usb0 uhub0: 2 ports with 2 removable, self powered uhci1: <intel 82801db="" (ich4)="" usb="" controller="" usb-b="">port 0xe100-0xe11f irq 5 at device 29.1 on pci0 uhci1: [GIANT-LOCKED] uhci1: [ITHREAD] usb1: <intel 82801db="" (ich4)="" usb="" controller="" usb-b="">on uhci1 usb1: USB revision 1.0 uhub1: <intel 1="" 9="" uhci="" root="" hub,="" class="" 0,="" rev="" 1.00="" 1.00,="" addr="">on usb1 uhub1: 2 ports with 2 removable, self powered ehci0: <intel 82801db="" l="" m="" (ich4)="" usb="" 2.0="" controller="">mem 0xe8200000-0xe82003ff irq 7 at device 29.7 on pci0 ehci0: [GIANT-LOCKED] ehci0: [ITHREAD] usb2: EHCI version 1.0 usb2: companion controllers, 2 ports each: usb0 usb1 usb2: <intel 82801db="" l="" m="" (ich4)="" usb="" 2.0="" controller="">on ehci0 usb2: USB revision 2.0 uhub2: <intel 1="" 9="" ehci="" root="" hub,="" class="" 0,="" rev="" 2.00="" 1.00,="" addr="">on usb2 uhub2: 4 ports with 4 removable, self powered pcib1: <acpi pci-pci="" bridge="">at device 30.0 on pci0 pci1: <acpi pci="" bus="">on pcib1 fxp0: <intel 100="" 82551="" pro="" ethernet="">port 0xd000-0xd03f mem 0xe8083000-0xe8083fff,0xe8000000-0xe801ffff irq 12 at device 4.0 on pci1 miibus0: <mii bus="">on fxp0 inphy0: <i82555 10="" 100="" media="" interface="">PHY 1 on miibus0 inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto fxp0: Ethernet address: 00:0e:b6:8c:44:a0 fxp0: [ITHREAD] fxp1: <intel 100="" 82551="" pro="" ethernet="">port 0xd100-0xd13f mem 0xe8081000-0xe8081fff,0xe8020000-0xe803ffff irq 10 at device 5.0 on pci1 miibus1: <mii bus="">on fxp1 inphy1: <i82555 10="" 100="" media="" interface="">PHY 1 on miibus1 inphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto fxp1: Ethernet address: 00:0e:b6:8c:44:a1 fxp1: [ITHREAD] fxp2: <intel 100="" 82551="" pro="" ethernet="">port 0xd200-0xd23f mem 0xe8080000-0xe8080fff,0xe8040000-0xe805ffff irq 11 at device 6.0 on pci1 miibus2: <mii bus="">on fxp2 inphy2: <i82555 10="" 100="" media="" interface="">PHY 1 on miibus2 inphy2: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto fxp2: Ethernet address: 00:0e:b6:2b:c2:e9 fxp2: [ITHREAD] fxp3: <intel 100="" 82551="" pro="" ethernet="">port 0xd300-0xd33f mem 0xe8082000-0xe8082fff,0xe8060000-0xe807ffff irq 5 at device 7.0 on pci1 miibus3: <mii bus="">on fxp3 inphy3: <i82555 10="" 100="" media="" interface="">PHY 1 on miibus3 inphy3: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto fxp3: Ethernet address: 00:0e:b6:2b:c2:e8 fxp3: [ITHREAD] isab0: <pci-isa bridge="">at device 31.0 on pci0 isa0: <isa bus="">on isab0 atapci0: <intel ich4="" udma100="" controller="">port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xf000-0xf00f at device 31.1 on pci0 ata0: <ata 0="" channel="">on atapci0 ata0: [ITHREAD] ata1: <ata 1="" channel="">on atapci0 ata1: [ITHREAD] pci0: <serial bus,="" smbus="">at device 31.3 (no driver attached) acpi_tz0: <thermal zone="">on acpi0 speaker0: <pc speaker="">port 0x61 on acpi0 sio0: <16550A-compatible COM port> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0 sio0: type 16550A, console sio0: [FILTER] sio1: <16550A-compatible COM port> port 0x2f8-0x2ff irq 3 on acpi0 sio1: type 16550A sio1: [FILTER] cpu0: <acpi cpu="">on acpi0 acpi_throttle0: <acpi cpu="" throttling="">on cpu0 orm0: <isa option="" roms="">at iomem 0xc0000-0xcc7ff,0xd0000-0xd17ff pnpid ORM0000 on isa0 ppc0: parallel port not found. Timecounter "TSC" frequency 1499835835 Hz quality 800 Timecounters tick every 10.000 msec IPsec: Initialized Security Association Processing. ad0: DMA limited to UDMA33, controller found non-ATA66 cable ad0: 57231MB <hts721060g9at00 mc3oa51a="">at ata0-master UDMA33 Trying to mount root from ufs:/dev/ad0s1a pflog0: promiscuous mode enabled</hts721060g9at00></isa></acpi></acpi></pc></thermal></serial></ata></ata></intel></isa></pci-isa></i82555></mii></intel></i82555></mii></intel></i82555></mii></intel></i82555></mii></intel></acpi></acpi></intel></intel></intel></intel></intel></intel></intel></intel></intel></vga-compatible></vga-compatible></acpi></acpi></power></intelr></software></fpu,vme,de,pse,tsc,msr,pae,mce,cx8,apic,sep,mtrr,pge,mca,cmov,pat,clflush,dts,acpi,mmx,fxsr,sse,sse2,ss,tm,pbe> -
Assigning fxp0 and fxp1 as LAN/WAN doesn't change them at all, still no link lights. Starting to look more and more like hardware I guess.
EDIT: On a whim I bridged fxp0 and fxp1 to fxp3 (LAN) to see if that would help, now it lists their status as "no carrier" instead of "down."
-
ok, do you need 4 ports? do they work with the factory riverbed image?
-
I don't need four, though it'd be nice, as for the factory image it wouldn't do much because the license had expired. I didn't think to test all the ports before reformatting because it seemed like a given that they'd work. Obviously I had too much faith in the technology.
-
so no way to get factory image (your using that drive?)
-
it looks like pf sees all 4 nics, and that all 4 are the same type.
did the guy who gave it to you use just the 2 that you got working? -
make sure everything is clean, ive had some lint/dust stop a device from working, i blew on it with air all over and looked at it very carefully for about 5 min to see if i missed anything, it fixed the problem
if all else fails its a 1.5 GHZ system with two 1 Gbps nics (working) but since the nics are Gbps i wouldnt use it for pf (unless you have a fiber connection) i would use it for freenas or the like.
-
Can't do a factory restore as I'm using the drive. It's a tiny little box which is why I was going to use it as a firewall, but I could see possibly using it for FreeNAS or such as well. The guy who gave it to me hadn't used it a long time, though he says he only ever used two ports so it's possible it's always had two dead ones. I suppose if nothing else it's running at the moment and has enough active ports to route if I needed it to.
Still, if there are any brainstorms on the other two ports I'd certainly appreciate the input. Thanks @XIII for all the suggestions.
-
Assigning fxp0 and fxp1 their own static addresses also gives the status "no carrier". Not 100% sure what that means though.
-
wallabybob may be able to decipher more from the dmesg than i could so he may respond (thought i saw him "making his rounds", also he was the one who thought of that)
hope it works out
the no carrier means no connection
-
Got'cha, hopefully he can shed some light on this, if not I've got a mostly working machine and a few new tricks for installing embedded. Thanks XIII.
-
your welcome, I try when I can (or think I can)
