Dell PowerEdge R510 keeps locking up on install

[the.it.dude]

Same problem with Intel NICs pulled.

This time it hung at "Writing Configuration" again.

[guiparm]

Try a external USB cdrom…. and check the MD5 of the .iso

[the.it.dude]

I did check the MD5 of both 32 & 64 bit versions before I even started.

I've now been able to successfully load and install 5 times in a row with the Intel Cards removed and the following BIOS settings:

Processor Settings

• Number of Cores per Processor = Single

• C States = Disabled

Integrated Devices

• PXE boot disabled on NIC1

• User Accessible USB Ports = Only Back Ports On

Moved IRQ Assignments around for devices

Power Management Set to "Max Performance"

Now I've played with different combinations of these settings before (with the Intel NICs installed) and did not have consistent success.  ???

I'll try re-installing the Intel NICs and see what happens with these same BIOS settings.

[guiparm]

Try disable also the Bios configuration options, under 'Processor Settings', there is this: Virtualization Technology….

[the.it.dude]

On this server, the Virtualization setting is disabled by default.  (I've also tried enabling it as well)

I just put the NICs back in and had problems again.  This time the setup completed fine.  When I selected Option 99 to install to the hard drive I got the normal blue screen asking for the keyboard/regional settings, etc.  I selected Accept Settings as usual and then the next screen never loads (Just a blank blue screen).  I can hit <ctrl><c>to get back to the menu, but subsequent attempts to install to the hard drive just displays a blue screen with a message at the bottom saying "Waiting for backend"

I just tried moving IRQs around again and will do more testing…</c></ctrl>

[the.it.dude]

Moving IRQs resulted in the same issue… blank blue screen when trying to install to the hard drive.

I then tried a USB DVD Drive to run the install from.  Same exact result.

It's starting to look like something related to the Intel Quad Port NICs  (Maybe not... Had a hang after pulling nics)

Continuing to test...

[the.it.dude]

I've discovered that removing 1 of the quad port nic's enables consistent configuration and installation.  (Doesn't matter which nic)  As soon as I put the 2nd quad port nic in, I have problems.  I'm now trying to figure out why having both nic's installed causes problems…

[the.it.dude]

Now I'm ticked…

I just ordered 2 new Dell PE servers for production firewalls:

R410 = 1 Dual Core CPU, SAS6ir, 1 Dual Port Broadcom NIC
R510 = 2 Dual Core CPUs, SAS6ir, 2 Quad Port Intel NICs

Having same issues with both servers!  This has got to be a freebsd thing, right?  Tomorrow, I'm going to try to load Untangle and see what happens.  My only other thought was to install ESXi and run pfSense as a VM.  But, I'm not real thrilled about that.

[wallabybob]

@the.it.dude:

I've discovered that removing 1 of the quad port nic's enables consistent configuration and installation.  (Doesn't matter which nic)  As soon as I put the 2nd quad port nic in, I have problems.  I'm now trying to figure out why having both nic's installed causes problems…

By I have problems do you mean the system locks up?

Are the two quad port NICs indentical parts?

Please post the output of the pfSense shell command # dmesg; vmstat -i on system with only one of the quad port NICs.

@the.it.dude:

Having same issues with both servers!

What issues exactly? If you can't install on the R410 you could clone the disk from the R410 and use the clone in the R410 to get over the install problem. Does the R410 have two onboard NICs? If not, does it behave better with only one NIC in the system? Do you know if they are bce or bge NICs?

[the.it.dude]

OK, Long Post.  But, everything should be in here now…  I'll create 2 seperate posts for the R410 & the R510:

R410

2 Internal NICs = Broadcom BCM5716 (bce)
Add-in Dual Port NIC = Broadcom BCM5709 (bce)

1st Test

Add-in NIC removed and BIOS settings all set to default
Everything OK!

R410 w/o NIC installed

$ dmesg; vmstat -i
Copyright 1992-2010 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 8.1-RELEASE-p2 #0: Sat Feb 26 18:05:58 EST 2011
    root@FreeBSD_8.0_pfSense_2.0-AMD64.snaps.pfsense.org:/usr/obj.pfSense/usr/pfSensesrc/src/sys/pfSense_SMP.8 amd64
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: Intel(R) Xeon(R) CPU          E5503  @ 2.00GHz (1995.01-MHz K8-class CPU)
  Origin = "GenuineIntel"  Id = 0x106a5  Family = 6  Model = 1a  Stepping = 5
  Features=0xbfebfbff <fpu,vme,de,pse,tsc,msr,pae,mce,cx8,apic,sep,mtrr,pge,mca,cmov,pat,pse36,clflush,dts,acpi,mmx,fxsr,sse,sse2,ss,htt,tm,pbe>Features2=0x9ce3bd <sse3,dtes64,mon,ds_cpl,vmx,est,tm2,ssse3,cx16,xtpr,pdcm,dca,sse4.1,sse4.2,popcnt>AMD Features=0x28100800 <syscall,nx,rdtscp,lm>AMD Features2=0x1 <lahf>TSC: P-state invariant
real memory  = 2147483648 (2048 MB)
avail memory = 2037293056 (1942 MB)
ACPI APIC Table: <dell  pe_sc3 ="">FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs
FreeBSD/SMP: 1 package(s) x 2 core(s)
cpu0 (BSP): APIC ID: 16
cpu1 (AP): APIC ID: 20
ioapic1: Changing APIC ID to 1
ioapic0 <version 2.0="">irqs 0-23 on motherboard
ioapic1 <version 2.0="">irqs 32-55 on motherboard
wpi: You need to read the LICENSE file in /usr/share/doc/legal/intel_wpi/.
wpi: If you agree with the license, set legal.intel_wpi.license_ack=1 in /boot/loader.conf.
module_register_init: MOD_LOAD (wpi_fw, 0xffffffff806512b0, 0) error 1
ipw_bss: You need to read the LICENSE file in /usr/share/doc/legal/intel_ipw/.
ipw_bss: If you agree with the license, set legal.intel_ipw.license_ack=1 in /boot/loader.conf.
module_register_init: MOD_LOAD (ipw_bss_fw, 0xffffffff8046d080, 0) error 1
ipw_ibss: You need to read the LICENSE file in /usr/share/doc/legal/intel_ipw/.
ipw_ibss: If you agree with the license, set legal.intel_ipw.license_ack=1 in /boot/loader.conf.
module_register_init: MOD_LOAD (ipw_ibss_fw, 0xffffffff8046d120, 0) error 1
wlan: mac acl policy registered
ipw_monitor: You need to read the LICENSE file in /usr/share/doc/legal/intel_ipw/.
ipw_monitor: If you agree with the license, set legal.intel_ipw.license_ack=1 in /boot/loader.conf.
module_register_init: MOD_LOAD (ipw_monitor_fw, 0xffffffff8046d1c0, 0) error 1
kbd1 at kbdmux0
cryptosoft0: <software crypto="">on motherboard
padlock0: No ACE support.
acpi0: <dell pe_sc3="">on motherboard
acpi0: [ITHREAD]
acpi0: Power Button (fixed)
Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x808-0x80b on acpi0
cpu0: <acpi cpu="">on acpi0
cpu1: <acpi cpu="">on acpi0
acpi_hpet0: <high precision="" event="" timer="">iomem 0xfed00000-0xfed003ff on acpi0
Timecounter "HPET" frequency 14318180 Hz quality 900
pcib0: <acpi host-pci="" bridge="">port 0xcf8-0xcff on acpi0
pci0: <acpi pci="" bus="">on pcib0
pcib1: <acpi pci-pci="" bridge="">at device 1.0 on pci0
pci1: <acpi pci="" bus="">on pcib1
bce0: <broadcom netxtreme="" ii="" bcm5716="" 1000base-t="" (c0)="">mem 0xda000000-0xdbffffff irq 36 at device 0.0 on pci1
miibus0: <mii bus="">on bce0
brgphy0: <bcm5709c 10="" 100="" 1000basetx="" phy="">PHY 1 on miibus0
brgphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto
bce0: [ITHREAD]
bce0: ASIC (0x57092008); Rev (C0); Bus (PCIe x4, 2.5Gbps); B/C (5.2.3); Flags (MSI|MFW); MFW (NCSI 2.0.11)
bce1: <broadcom netxtreme="" ii="" bcm5716="" 1000base-t="" (c0)="">mem 0xdc000000-0xddffffff irq 48 at device 0.1 on pci1
miibus1: <mii bus="">on bce1
brgphy1: <bcm5709c 10="" 100="" 1000basetx="" phy="">PHY 1 on miibus1
brgphy1:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto
bce1: [ITHREAD]
bce1: ASIC (0x57092008); Rev (C0); Bus (PCIe x4, 2.5Gbps); B/C (5.2.3); Flags (MSI|MFW); MFW (NCSI 2.0.11)
pcib2: <acpi pci-pci="" bridge="">at device 3.0 on pci0
pci2: <acpi pci="" bus="">on pcib2
mpt0: <lsilogic sas="" sata="" adapter="">port 0xfc00-0xfcff mem 0xdf2ec000-0xdf2effff,0xdf2f0000-0xdf2fffff irq 32 at device 0.0 on pci2
mpt0: [ITHREAD]
mpt0: MPI Version=1.5.18.0
mpt0: Capabilities: ( RAID-0 RAID-1E RAID-1 )
mpt0: 1 Active Volume (2 Max)
mpt0: 2 Hidden Drive Members (14 Max)
pcib3: <acpi pci-pci="" bridge="">at device 7.0 on pci0
pci3: <acpi pci="" bus="">on pcib3
pci0: <base peripheral,="" interrupt="" controller=""> at device 20.0 (no driver attached)
pci0: <base peripheral,="" interrupt="" controller=""> at device 20.1 (no driver attached)
pci0: <base peripheral,="" interrupt="" controller=""> at device 20.2 (no driver attached)
uhci0: <intel 82801ji="" (ich10)="" usb="" controller="" usb-d="">port 0xec40-0xec5f irq 17 at device 26.0 on pci0
uhci0: [ITHREAD]
usbus0: <intel 82801ji="" (ich10)="" usb="" controller="" usb-d="">on uhci0
uhci1: <intel 82801ji="" (ich10)="" usb="" controller="" usb-e="">port 0xec60-0xec7f irq 18 at device 26.1 on pci0
uhci1: [ITHREAD]
usbus1: <intel 82801ji="" (ich10)="" usb="" controller="" usb-e="">on uhci1
ehci0: <intel 82801ji="" (ich10)="" usb="" 2.0="" controller="" usb-b="">mem 0xdf0fe000-0xdf0fe3ff irq 19 at device 26.7 on pci0
ehci0: [ITHREAD]
usbus2: EHCI version 1.0
usbus2: <intel 82801ji="" (ich10)="" usb="" 2.0="" controller="" usb-b="">on ehci0
uhci2: <intel 82801ji="" (ich10)="" usb="" controller="" usb-a="">port 0xec80-0xec9f irq 21 at device 29.0 on pci0
uhci2: [ITHREAD]
usbus3: <intel 82801ji="" (ich10)="" usb="" controller="" usb-a="">on uhci2
uhci3: <intel 82801ji="" (ich10)="" usb="" controller="" usb-b="">port 0xeca0-0xecbf irq 20 at device 29.1 on pci0
uhci3: [ITHREAD]
usbus4: <intel 82801ji="" (ich10)="" usb="" controller="" usb-b="">on uhci3
uhci4: <intel 82801ji="" (ich10)="" usb="" controller="" usb-c="">port 0xecc0-0xecdf irq 21 at device 29.2 on pci0
uhci4: [ITHREAD]
usbus5: <intel 82801ji="" (ich10)="" usb="" controller="" usb-c="">on uhci4
uhci5: <intel 82801ji="" (ich10)="" usb="" controller="" usb-f="">port 0xece0-0xecff irq 20 at device 29.3 on pci0
uhci5: [ITHREAD]
usbus6: <intel 82801ji="" (ich10)="" usb="" controller="" usb-f="">on uhci5
ehci1: <intel 82801ji="" (ich10)="" usb="" 2.0="" controller="" usb-a="">mem 0xdf0ff000-0xdf0ff3ff irq 21 at device 29.7 on pci0
ehci1: [ITHREAD]
usbus7: EHCI version 1.0
usbus7: <intel 82801ji="" (ich10)="" usb="" 2.0="" controller="" usb-a="">on ehci1
pcib4: <acpi pci-pci="" bridge="">at device 30.0 on pci0
pci4: <acpi pci="" bus="">on pcib4
vgapci0: <vga-compatible display="">mem 0xd9800000-0xd9ffffff,0xde7fc000-0xde7fffff,0xde800000-0xdeffffff irq 19 at device 3.0 on pci4
isab0: <pci-isa bridge="">at device 31.0 on pci0
isa0: <isa bus="">on isab0
atapci0: <intel ich10="" sata300="" controller="">port 0xe8e0-0xe8e7,0xe8d0-0xe8d3,0xe8e8-0xe8ef,0xe8d4-0xe8d7,0xec00-0xec0f,0xec10-0xec1f irq 23 at device 31.2 on pci0
atapci0: [ITHREAD]
ata2: <ata 0="" channel="">on atapci0
ata2: [ITHREAD]
ata3: <ata 1="" channel="">on atapci0
ata3: [ITHREAD]
atapci1: <intel ich10="" sata300="" controller="">port 0xe8f0-0xe8f7,0xe8d8-0xe8db,0xe8f8-0xe8ff,0xe8dc-0xe8df,0xec20-0xec2f,0xec30-0xec3f irq 22 at device 31.5 on pci0
atapci1: [ITHREAD]
ata4: <ata 0="" channel="">on atapci1
ata4: [ITHREAD]
ata5: <ata 1="" channel="">on atapci1
ata5: [ITHREAD]
atrtc0: <at realtime="" clock="">port 0x70-0x7f irq 8 on acpi0
uart0: <16550 or compatible> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0
uart0: [FILTER]
uart1: <16550 or compatible> port 0x2f8-0x2ff irq 3 on acpi0
uart1: [FILTER]
orm0: <isa option="" roms="">at iomem 0xc0000-0xc7fff,0xce000-0xcefff,0xec000-0xeffff on isa0
sc0: <system console="">at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
vga0: <generic isa="" vga="">at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
atkbdc0: <keyboard controller="" (i8042)="">at port 0x60,0x64 on isa0
atkbd0: <at keyboard="">irq 1 on atkbdc0
kbd0 at atkbd0
atkbd0: [GIANT-LOCKED]
atkbd0: [ITHREAD]
ppc0: cannot reserve I/O port range
est0: <enhanced speedstep="" frequency="" control="">on cpu0
est: CPU supports Enhanced Speedstep, but is not recognized.
est: cpu_vendor GenuineIntel, msr f
device_attach: est0 attach returned 6
p4tcc0: <cpu frequency="" thermal="" control="">on cpu0
est1: <enhanced speedstep="" frequency="" control="">on cpu1
est: CPU supports Enhanced Speedstep, but is not recognized.
est: cpu_vendor GenuineIntel, msr f
device_attach: est1 attach returned 6
p4tcc1: <cpu frequency="" thermal="" control="">on cpu1
Timecounters tick every 1.000 msec
IPsec: Initialized Security Association Processing.
usbus0: 12Mbps Full Speed USB v1.0
usbus1: 12Mbps Full Speed USB v1.0
usbus2: 480Mbps High Speed USB v2.0
usbus3: 12Mbps Full Speed USB v1.0
usbus4: 12Mbps Full Speed USB v1.0
usbus5: 12Mbps Full Speed USB v1.0
usbus6: 12Mbps Full Speed USB v1.0
usbus7: 480Mbps High Speed USB v2.0
mpt0:vol0(mpt0:0:0): Settings ( Member-WCE Hot-Plug-Spares High-Priority-ReSync )ugen0.1: <intel>at usbus0
uhub0: <intel 1="" 9="" uhci="" root="" hub,="" class="" 0,="" rev="" 1.00="" 1.00,="" addr="">on usbus0
ugen1.1: <intel>at usbus1
uhub1: <intel 1="" 9="" uhci="" root="" hub,="" class="" 0,="" rev="" 1.00="" 1.00,="" addr="">on usbus1
ugen2.1: <intel>at usbus2
uhub2: <intel 1="" 9="" ehci="" root="" hub,="" class="" 0,="" rev="" 2.00="" 1.00,="" addr="">on usbus2
ugen3.1: <intel>at usbus3
uhub3: <intel 1="" 9="" uhci="" root="" hub,="" class="" 0,="" rev="" 1.00="" 1.00,="" addr="">on usbus3
ugen4.1: <intel>at usbus4
uhub4: <intel 1="" 9="" uhci="" root="" hub,="" class="" 0,="" rev="" 1.00="" 1.00,="" addr="">on usbus4
ugen5.1: <intel>at usbus5
uhub5: <intel 1="" 9="" uhci="" root="" hub,="" class="" 0,="" rev="" 1.00="" 1.00,="" addr="">on usbus5
ugen6.1: <intel>at usbus6
uhub6: <intel 1="" 9="" uhci="" root="" hub,="" class="" 0,="" rev="" 1.00="" 1.00,="" addr="">on usbus6
ugen7.1: <intel>at usbus7
uhub7: <intel 1="" 9="" ehci="" root="" hub,="" class="" 0,="" rev="" 2.00="" 1.00,="" addr="">on usbus7

mpt0:vol0(mpt0:0:0): Using Spare Pool: 0
mpt0:vol0(mpt0:0:0): 2 Members:
      (mpt0:1:8:0): Primary Online
      (mpt0:1:1:0): Secondary Online
mpt0:vol0(mpt0:0:0): RAID-1 - Optimal
mpt0:vol0(mpt0:0:0): Status ( Enabled )
(mpt0:vol0:1): Physical (mpt0:0:1:0), Pass-thru (mpt0:1:0:0)
(mpt0:vol0:1): Online
(mpt0:vol0:0): Physical (mpt0:0:8:0), Pass-thru (mpt0:1:1:0)
(mpt0:vol0:0): Online
uhub0: 2 ports with 2 removable, self powered
uhub1: 2 ports with 2 removable, self powered
uhub3: 2 ports with 2 removable, self powered
uhub4: 2 ports with 2 removable, self powered
uhub5: 2 ports with 2 removable, self powered
uhub6: 2 ports with 2 removable, self powered
uhub2: 4 ports with 4 removable, self powered
uhub7: 4 ports with 4 removable, self powered
pass1 at mpt0 bus 1 scbus1 target 0 lun 0
pass1: <ata wdc="" wd2502abys-1="" 3b05="">Fixed Uninstalled SCSI-5 device
pass1: 300.000MB/s transfers
pass1: Command Queueing enabled
da0 at mpt0 bus 0 scbus0 target 0 lun 0
da0: <dell 1028="" virtual="" disk="">Fixed Direct Access SCSI-5 device
da0: 300.000MB/s transfers
da0: Command Queueing enabled
da0: 237824MB (487063552 512 byte sectors: 255H 63S/T 30318C)
acd0: DVDROM <teac dvd-rom="" dv-28sw="" r.2a="">at ata4-master UDMA100 SATA 1.5Gb/s
SMP: AP CPU #1 Launched!
ugen2.2: <vendor 0x0424="">at usbus2
uhub8: <vendor 2="" 9="" 0x0424="" product="" 0x2514,="" class="" 0,="" rev="" 2.00="" 0.00,="" addr="">on usbus2
ugen0.2: <dell>at usbus0
ukbd0: <ep1 interrupt="">on usbus0
kbd2 at ukbd0
uhub8: 2 ports with 2 removable, self powered
Trying to mount root from cd9660:/dev/iso9660/pfSense
md0.uzip: 3159 x 65536 blocks
pflog0: promiscuous mode enabled
interrupt                          total      rate
irq17: uhci0                          49          0
irq19: ehci0                        147          0
irq22: atapci1                      3746        14
irq32: mpt0                          425          1
cpu0: timer                      502014      1976
irq256: bce0                          1          0
irq257: bce1                        753          2
cpu1: timer                      493465      1942
Total                            1000600      3939

2nd Test

Install Add-in Dual Port NIC to already installed pfSense on hard drive
Assign Interfaces
Everything OK!

R410 w/ NIC Installed

$ dmesg; vmstat -i
Copyright 1992-2010 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 8.1-RELEASE-p2 #0: Sat Feb 26 18:05:58 EST 2011
    root@FreeBSD_8.0_pfSense_2.0-AMD64.snaps.pfsense.org:/usr/obj.pfSense/usr/pfSensesrc/src/sys/pfSense_SMP.8 amd64
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: Intel(R) Xeon(R) CPU          E5503  @ 2.00GHz (1995.01-MHz K8-class CPU)
  Origin = "GenuineIntel"  Id = 0x106a5  Family = 6  Model = 1a  Stepping = 5
  Features=0xbfebfbff <fpu,vme,de,pse,tsc,msr,pae,mce,cx8,apic,sep,mtrr,pge,mca,cmov,pat,pse36,clflush,dts,acpi,mmx,fxsr,sse,sse2,ss,htt,tm,pbe>Features2=0x9ce3bd <sse3,dtes64,mon,ds_cpl,vmx,est,tm2,ssse3,cx16,xtpr,pdcm,dca,sse4.1,sse4.2,popcnt>AMD Features=0x28100800 <syscall,nx,rdtscp,lm>AMD Features2=0x1 <lahf>TSC: P-state invariant
real memory  = 2147483648 (2048 MB)
avail memory = 2037805056 (1943 MB)
ACPI APIC Table: <dell  pe_sc3 ="">FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs
FreeBSD/SMP: 1 package(s) x 2 core(s)
cpu0 (BSP): APIC ID: 16
cpu1 (AP): APIC ID: 20
ioapic1: Changing APIC ID to 1
ioapic0 <version 2.0="">irqs 0-23 on motherboard
ioapic1 <version 2.0="">irqs 32-55 on motherboard
wpi: You need to read the LICENSE file in /usr/share/doc/legal/intel_wpi/.
wpi: If you agree with the license, set legal.intel_wpi.license_ack=1 in /boot/loader.conf.
module_register_init: MOD_LOAD (wpi_fw, 0xffffffff806512b0, 0) error 1
ipw_bss: You need to read the LICENSE file in /usr/share/doc/legal/intel_ipw/.
ipw_bss: If you agree with the license, set legal.intel_ipw.license_ack=1 in /boot/loader.conf.
module_register_init: MOD_LOAD (ipw_bss_fw, 0xffffffff8046d080, 0) error 1
ipw_ibss: You need to read the LICENSE file in /usr/share/doc/legal/intel_ipw/.
ipw_ibss: If you agree with the license, set legal.intel_ipw.license_ack=1 in /boot/loader.conf.
module_register_init: MOD_LOAD (ipw_ibss_fw, 0xffffffff8046d120, 0) error 1
wlan: mac acl policy registered
ipw_monitor: You need to read the LICENSE file in /usr/share/doc/legal/intel_ipw/.
ipw_monitor: If you agree with the license, set legal.intel_ipw.license_ack=1 in /boot/loader.conf.
module_register_init: MOD_LOAD (ipw_monitor_fw, 0xffffffff8046d1c0, 0) error 1
kbd1 at kbdmux0
cryptosoft0: <software crypto="">on motherboard
padlock0: No ACE support.
acpi0: <dell pe_sc3="">on motherboard
acpi0: [ITHREAD]
acpi0: Power Button (fixed)
Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x808-0x80b on acpi0
cpu0: <acpi cpu="">on acpi0
cpu1: <acpi cpu="">on acpi0
acpi_hpet0: <high precision="" event="" timer="">iomem 0xfed00000-0xfed003ff on acpi0
Timecounter "HPET" frequency 14318180 Hz quality 900
pcib0: <acpi host-pci="" bridge="">port 0xcf8-0xcff on acpi0
pci0: <acpi pci="" bus="">on pcib0
pcib1: <acpi pci-pci="" bridge="">at device 1.0 on pci0
pci1: <acpi pci="" bus="">on pcib1
bce0: <broadcom netxtreme="" ii="" bcm5716="" 1000base-t="" (c0)="">mem 0xd6000000-0xd7ffffff irq 36 at device 0.0 on pci1
miibus0: <mii bus="">on bce0
brgphy0: <bcm5709c 10="" 100="" 1000basetx="" phy="">PHY 1 on miibus0
brgphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto
bce0: [ITHREAD]
bce0: ASIC (0x57092008); Rev (C0); Bus (PCIe x4, 2.5Gbps); B/C (5.2.3); Flags (MSI|MFW); MFW (NCSI 2.0.11)
bce1: <broadcom netxtreme="" ii="" bcm5716="" 1000base-t="" (c0)="">mem 0xd8000000-0xd9ffffff irq 48 at device 0.1 on pci1
miibus1: <mii bus="">on bce1
brgphy1: <bcm5709c 10="" 100="" 1000basetx="" phy="">PHY 1 on miibus1
brgphy1:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto
bce1: [ITHREAD]
bce1: ASIC (0x57092008); Rev (C0); Bus (PCIe x4, 2.5Gbps); B/C (5.2.3); Flags (MSI|MFW); MFW (NCSI 2.0.11)
pcib2: <acpi pci-pci="" bridge="">at device 3.0 on pci0
pci2: <acpi pci="" bus="">on pcib2
mpt0: <lsilogic sas="" sata="" adapter="">port 0xfc00-0xfcff mem 0xdf2ec000-0xdf2effff,0xdf2f0000-0xdf2fffff irq 32 at device 0.0 on pci2
mpt0: [ITHREAD]
mpt0: MPI Version=1.5.18.0
mpt0: Capabilities: ( RAID-0 RAID-1E RAID-1 )
mpt0: 1 Active Volume (2 Max)
mpt0: 2 Hidden Drive Members (14 Max)
pcib3: <acpi pci-pci="" bridge="">at device 7.0 on pci0
pci3: <acpi pci="" bus="">on pcib3
bce2: <broadcom netxtreme="" ii="" bcm5709="" 1000base-t="" (c0)="">mem 0xda000000-0xdbffffff irq 38 at device 0.0 on pci3
miibus2: <mii bus="">on bce2
brgphy2: <bcm5709c 10="" 100="" 1000basetx="" phy="">PHY 1 on miibus2
brgphy2:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto
bce2: [ITHREAD]
bce2: ASIC (0x57092003); Rev (C0); Bus (PCIe x4, 2.5Gbps); B/C (5.2.3); Flags (MSI)
bce3: <broadcom netxtreme="" ii="" bcm5709="" 1000base-t="" (c0)="">mem 0xdc000000-0xddffffff irq 45 at device 0.1 on pci3
miibus3: <mii bus="">on bce3
brgphy3: <bcm5709c 10="" 100="" 1000basetx="" phy="">PHY 1 on miibus3
brgphy3:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto
bce3: [ITHREAD]
bce3: ASIC (0x57092003); Rev (C0); Bus (PCIe x4, 2.5Gbps); B/C (5.2.3); Flags (MSI)
pci0: <base peripheral,="" interrupt="" controller=""> at device 20.0 (no driver attached)
pci0: <base peripheral,="" interrupt="" controller=""> at device 20.1 (no driver attached)
pci0: <base peripheral,="" interrupt="" controller=""> at device 20.2 (no driver attached)
uhci0: <intel 82801ji="" (ich10)="" usb="" controller="" usb-d="">port 0xec40-0xec5f irq 17 at device 26.0 on pci0
uhci0: [ITHREAD]
usbus0: <intel 82801ji="" (ich10)="" usb="" controller="" usb-d="">on uhci0
uhci1: <intel 82801ji="" (ich10)="" usb="" controller="" usb-e="">port 0xec60-0xec7f irq 18 at device 26.1 on pci0
uhci1: [ITHREAD]
usbus1: <intel 82801ji="" (ich10)="" usb="" controller="" usb-e="">on uhci1
ehci0: <intel 82801ji="" (ich10)="" usb="" 2.0="" controller="" usb-b="">mem 0xdf0fe000-0xdf0fe3ff irq 19 at device 26.7 on pci0
ehci0: [ITHREAD]
usbus2: EHCI version 1.0
usbus2: <intel 82801ji="" (ich10)="" usb="" 2.0="" controller="" usb-b="">on ehci0
uhci2: <intel 82801ji="" (ich10)="" usb="" controller="" usb-a="">port 0xec80-0xec9f irq 21 at device 29.0 on pci0
uhci2: [ITHREAD]
usbus3: <intel 82801ji="" (ich10)="" usb="" controller="" usb-a="">on uhci2
uhci3: <intel 82801ji="" (ich10)="" usb="" controller="" usb-b="">port 0xeca0-0xecbf irq 20 at device 29.1 on pci0
uhci3: [ITHREAD]
usbus4: <intel 82801ji="" (ich10)="" usb="" controller="" usb-b="">on uhci3
uhci4: <intel 82801ji="" (ich10)="" usb="" controller="" usb-c="">port 0xecc0-0xecdf irq 21 at device 29.2 on pci0
uhci4: [ITHREAD]
usbus5: <intel 82801ji="" (ich10)="" usb="" controller="" usb-c="">on uhci4
uhci5: <intel 82801ji="" (ich10)="" usb="" controller="" usb-f="">port 0xece0-0xecff irq 20 at device 29.3 on pci0
uhci5: [ITHREAD]
usbus6: <intel 82801ji="" (ich10)="" usb="" controller="" usb-f="">on uhci5
ehci1: <intel 82801ji="" (ich10)="" usb="" 2.0="" controller="" usb-a="">mem 0xdf0ff000-0xdf0ff3ff irq 21 at device 29.7 on pci0
ehci1: [ITHREAD]
usbus7: EHCI version 1.0
usbus7: <intel 82801ji="" (ich10)="" usb="" 2.0="" controller="" usb-a="">on ehci1
pcib4: <acpi pci-pci="" bridge="">at device 30.0 on pci0
pci4: <acpi pci="" bus="">on pcib4
vgapci0: <vga-compatible display="">mem 0xd5800000-0xd5ffffff,0xde7fc000-0xde7fffff,0xde800000-0xdeffffff irq 19 at device 3.0 on pci4
isab0: <pci-isa bridge="">at device 31.0 on pci0
isa0: <isa bus="">on isab0
atapci0: <intel ich10="" sata300="" controller="">port 0xe8e0-0xe8e7,0xe8d0-0xe8d3,0xe8e8-0xe8ef,0xe8d4-0xe8d7,0xec00-0xec0f,0xec10-0xec1f irq 23 at device 31.2 on pci0
atapci0: [ITHREAD]
ata2: <ata 0="" channel="">on atapci0
ata2: [ITHREAD]
ata3: <ata 1="" channel="">on atapci0
ata3: [ITHREAD]
atapci1: <intel ich10="" sata300="" controller="">port 0xe8f0-0xe8f7,0xe8d8-0xe8db,0xe8f8-0xe8ff,0xe8dc-0xe8df,0xec20-0xec2f,0xec30-0xec3f irq 22 at device 31.5 on pci0
atapci1: [ITHREAD]
ata4: <ata 0="" channel="">on atapci1
ata4: [ITHREAD]
ata5: <ata 1="" channel="">on atapci1
ata5: [ITHREAD]
atrtc0: <at realtime="" clock="">port 0x70-0x7f irq 8 on acpi0
uart0: <16550 or compatible> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0
uart0: [FILTER]
uart1: <16550 or compatible> port 0x2f8-0x2ff irq 3 on acpi0
uart1: [FILTER]
orm0: <isa option="" roms="">at iomem 0xc0000-0xc7fff,0xce000-0xcefff,0xec000-0xeffff on isa0
sc0: <system console="">at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
vga0: <generic isa="" vga="">at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
atkbdc0: <keyboard controller="" (i8042)="">at port 0x60,0x64 on isa0
atkbd0: <at keyboard="">irq 1 on atkbdc0
kbd0 at atkbd0
atkbd0: [GIANT-LOCKED]
atkbd0: [ITHREAD]
ppc0: cannot reserve I/O port range
est0: <enhanced speedstep="" frequency="" control="">on cpu0
est: CPU supports Enhanced Speedstep, but is not recognized.
est: cpu_vendor GenuineIntel, msr f
device_attach: est0 attach returned 6
p4tcc0: <cpu frequency="" thermal="" control="">on cpu0
est1: <enhanced speedstep="" frequency="" control="">on cpu1
est: CPU supports Enhanced Speedstep, but is not recognized.
est: cpu_vendor GenuineIntel, msr f
device_attach: est1 attach returned 6
p4tcc1: <cpu frequency="" thermal="" control="">on cpu1
Timecounters tick every 1.000 msec
IPsec: Initialized Security Association Processing.
usbus0: 12Mbps Full Speed USB v1.0
usbus1: 12Mbps Full Speed USB v1.0
usbus2: 480Mbps High Speed USB v2.0
usbus3: 12Mbps Full Speed USB v1.0
usbus4: 12Mbps Full Speed USB v1.0
usbus5: 12Mbps Full Speed USB v1.0
usbus6: 12Mbps Full Speed USB v1.0
usbus7: 480Mbps High Speed USB v2.0
mpt0:vol0(mpt0:0:0): Settings (ugen0.1: <intel>at usbus0
uhub0: <intel 1="" 9="" uhci="" root="" hub,="" class="" 0,="" rev="" 1.00="" 1.00,="" addr="">on usbus0
ugen1.1: <intel>at usbus1
uhub1: <intel 1="" 9="" uhci="" root="" hub,="" class="" 0,="" rev="" 1.00="" 1.00,="" addr="">on usbus1
ugen2.1: <intel>at usbus2
uhub2: <intel 1="" 9="" ehci="" root="" hub,="" class="" 0,="" rev="" 2.00="" 1.00,="" addr="">on usbus2
ugen3.1: <intel>at usbus3
uhub3: <intel 1="" 9="" uhci="" root="" hub,="" class="" 0,="" rev="" 1.00="" 1.00,="" addr="">on usbus3
ugen4.1: <intel>at usbus4
uhub4: <intel 1="" 9="" uhci="" root="" hub,="" class="" 0,="" rev="" 1.00="" 1.00,="" addr="">on usbus4
ugen5.1: <intel>at usbus5
uhub5: <intel 1="" 9="" uhci="" root="" hub,="" class="" 0,="" rev="" 1.00="" 1.00,="" addr="">on usbus5
ugen6.1: <intel>at usbus6
uhub6: <intel 1="" 9="" uhci="" root="" hub,="" class="" 0,="" rev="" 1.00="" 1.00,="" addr="">on usbus6
ugen7.1: <intel>at usbus7
uhub7: <intel 1="" 9="" ehci="" root="" hub,="" class="" 0,="" rev="" 2.00="" 1.00,="" addr="">on usbus7
Member-WCE Hot-Plug-Spares High-Priority-ReSync )
mpt0:vol0(mpt0:0:0): Using Spare Pool: 0
mpt0:vol0(mpt0:0:0): 2 Members:
      (mpt0:1:8:0): Primary Online
      (mpt0:1:1:0): Secondary Online
mpt0:vol0(mpt0:0:0): RAID-1 - Optimal
mpt0:vol0(mpt0:0:0): Status ( Enabled )
(mpt0:vol0:1): Physical (mpt0:0:1:0), Pass-thru (mpt0:1:0:0)
(mpt0:vol0:1): Online
(mpt0:vol0:0): Physical (mpt0:0:8:0), Pass-thru (mpt0:1:1:0)
(mpt0:vol0:0): Online
uhub0: 2 ports with 2 removable, self powered
uhub1: 2 ports with 2 removable, self powered
uhub3: 2 ports with 2 removable, self powered
uhub4: 2 ports with 2 removable, self powered
uhub5: 2 ports with 2 removable, self powered
uhub6: 2 ports with 2 removable, self powered
uhub2: 4 ports with 4 removable, self powered
uhub7: 4 ports with 4 removable, self powered
pass1 at mpt0 bus 1 scbus1 target 0 lun 0
pass1: <ata wdc="" wd2502abys-1="" 3b05="">Fixed Uninstalled SCSI-5 device
pass1: 300.000MB/s transfers
pass1: Command Queueing enabled
da0 at mpt0 bus 0 scbus0 target 0 lun 0
da0: <dell 1028="" virtual="" disk="">Fixed Direct Access SCSI-5 device
da0: 300.000MB/s transfers
da0: Command Queueing enabled
da0: 237824MB (487063552 512 byte sectors: 255H 63S/T 30318C)
acd0: DVDROM <teac dvd-rom="" dv-28sw="" r.2a="">at ata4-master UDMA100 SATA 1.5Gb/s
SMP: AP CPU #1 Launched!
Root mount waiting for: usbus2
ugen2.2: <vendor 0x0424="">at usbus2
uhub8: <vendor 2="" 9="" 0x0424="" product="" 0x2514,="" class="" 0,="" rev="" 2.00="" 0.00,="" addr="">on usbus2
ugen0.2: <dell>at usbus0
ukbd0: <ep1 interrupt="">on usbus0
kbd2 at ukbd0
uhub8: 2 ports with 2 removable, self powered
Trying to mount root from ufs:/dev/da0s1a
pflog0: promiscuous mode enabled
bce1: link state changed to UP
interrupt                          total      rate
irq17: uhci0                          19          0
irq19: ehci0                          48          0
irq22: atapci1                        68          1
irq32: mpt0                        2049        35
cpu0: timer                      114559      1975
irq256: bce0                          1          0
irq257: bce1                        413          7
cpu1: timer                      106013      1827
Total                            223170      3847

3rd Test

Restart LiveCD with Add-in NIC installed and BIOS Settings at Default
Completes LiveCD boot and configuration.
Enter Option 99 to Install to Hard Drive
  Configure Console - Enter to "Accept these Settings"
  I never get the next screen.  I just see a blue screen w/ F10=Refresh Display in the upper left.
  I can hit <ctrl><c>to get back to the menu

What about running the install with the add-in nic installed causes a problem with installing to the hard drive?</c></ctrl></ep1></dell></vendor></vendor></teac></dell></ata></intel></intel></intel></intel></intel></intel></intel></intel></intel></intel></intel></intel></intel></intel></intel></intel></cpu></enhanced></cpu></enhanced></at></keyboard></generic></system></isa></at></ata></ata></intel></ata></ata></intel></isa></pci-isa></vga-compatible></acpi></acpi></intel></intel></intel></intel></intel></intel></intel></intel></intel></intel></intel></intel></intel></intel></intel></intel></bcm5709c></mii></broadcom></bcm5709c></mii></broadcom></acpi></acpi></lsilogic></acpi></acpi></bcm5709c></mii></broadcom></bcm5709c></mii></broadcom></acpi></acpi></acpi></acpi></high></acpi></acpi></dell></software></version></version></dell ></lahf></syscall,nx,rdtscp,lm></sse3,dtes64,mon,ds_cpl,vmx,est,tm2,ssse3,cx16,xtpr,pdcm,dca,sse4.1,sse4.2,popcnt></fpu,vme,de,pse,tsc,msr,pae,mce,cx8,apic,sep,mtrr,pge,mca,cmov,pat,pse36,clflush,dts,acpi,mmx,fxsr,sse,sse2,ss,htt,tm,pbe></ep1></dell></vendor></vendor></teac></dell></ata></intel></intel></intel></intel></intel></intel></intel></intel></intel></intel></intel></intel></intel></intel></intel></intel></cpu></enhanced></cpu></enhanced></at></keyboard></generic></system></isa></at></ata></ata></intel></ata></ata></intel></isa></pci-isa></vga-compatible></acpi></acpi></intel></intel></intel></intel></intel></intel></intel></intel></intel></intel></intel></intel></intel></intel></intel></intel></acpi></acpi></lsilogic></acpi></acpi></bcm5709c></mii></broadcom></bcm5709c></mii></broadcom></acpi></acpi></acpi></acpi></high></acpi></acpi></dell></software></version></version></dell ></lahf></syscall,nx,rdtscp,lm></sse3,dtes64,mon,ds_cpl,vmx,est,tm2,ssse3,cx16,xtpr,pdcm,dca,sse4.1,sse4.2,popcnt></fpu,vme,de,pse,tsc,msr,pae,mce,cx8,apic,sep,mtrr,pge,mca,cmov,pat,pse36,clflush,dts,acpi,mmx,fxsr,sse,sse2,ss,htt,tm,pbe>

[the.it.dude]

R510

2 Internal NICs = Broadcom BCM5716 (bce)
2 Add-in Quad Port NICs = Intel PRO/1000 v. 2.0.7 (igb)

1st Test

Both Add-in NICs removed
BIOS Settings at default

During Boot, right after prompt for:
  (R)ecovery mode…
  (I)nstaller...
  (C) Continues the LiveCD bootup...

I see the following on screen:

Loading Configuration......done.
Network intface mismatch -- Running interface assignment option.
bce1: link state changed to DOWN
bce1: link state changed to UP

And then nothing...  Just a non-blinking cursor
The Keyboard works... if I hit <enter>, I see carriage returns on the screen, but nothing else
If I hit the power button on the server, I see:
  acpi0: suspend request ignored (not ready yet)
  acpi0: request to enter state S5 failed (err 6)

Subsequent attempts with the same settings worked fine

Could not re-create that 1st problem
Everything Works!

2nd Test

Added 1 Add-In Quad Port NIC to already installed pfSense
Assigned Interfaces
Everything Works!

R510 w/ 1 of the Quad Port NICs installed

$ dmesg; vmstat -i
Copyright 1992-2010 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 8.1-RELEASE-p2 #0: Sat Feb 26 15:29:09 EST 2011
    sullrich@FreeBSD_8.0_pfSense_2.0-snaps.pfsense.org:/usr/obj.pfSense/usr/pfSensesrc/src/sys/pfSense_SMP.8 i386
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: Intel(R) Xeon(R) CPU          E5503  @ 2.00GHz (2000.08-MHz 686-class CPU)
  Origin = "GenuineIntel"  Id = 0x106a5  Family = 6  Model = 1a  Stepping = 5
  Features=0xbfebfbff <fpu,vme,de,pse,tsc,msr,pae,mce,cx8,apic,sep,mtrr,pge,mca,cmov,pat,pse36,clflush,dts,acpi,mmx,fxsr,sse,sse2,ss,htt,tm,pbe>Features2=0x9ce3bd <sse3,dtes64,mon,ds_cpl,vmx,est,tm2,ssse3,cx16,xtpr,pdcm,dca,sse4.1,sse4.2,popcnt>AMD Features=0x28100000 <nx,rdtscp,lm>AMD Features2=0x1 <lahf>TSC: P-state invariant
real memory  = 2147483648 (2048 MB)
avail memory = 2069499904 (1973 MB)
ACPI APIC Table: <dell  pe_sc3 ="">FreeBSD/SMP: Multiprocessor System Detected: 4 CPUs
FreeBSD/SMP: 2 package(s) x 2 core(s)
cpu0 (BSP): APIC ID: 16
cpu1 (AP): APIC ID: 20
cpu2 (AP): APIC ID:  0
cpu3 (AP): APIC ID:  4
ioapic1: Changing APIC ID to 1
ioapic0 <version 2.0="">irqs 0-23 on motherboard
ioapic1 <version 2.0="">irqs 32-55 on motherboard
wpi: You need to read the LICENSE file in /usr/share/doc/legal/intel_wpi/.
wpi: If you agree with the license, set legal.intel_wpi.license_ack=1 in /boot/loader.conf.
module_register_init: MOD_LOAD (wpi_fw, 0xc095c1e0, 0) error 1
ipw_bss: You need to read the LICENSE file in /usr/share/doc/legal/intel_ipw/.
ipw_bss: If you agree with the license, set legal.intel_ipw.license_ack=1 in /boot/loader.conf.
module_register_init: MOD_LOAD (ipw_bss_fw, 0xc0767240, 0) error 1
ipw_ibss: You need to read the LICENSE file in /usr/share/doc/legal/intel_ipw/.
ipw_ibss: If you agree with the license, set legal.intel_ipw.license_ack=1 in /boot/loader.conf.
module_register_init: MOD_LOAD (ipw_ibss_fw, 0xc0767300, 0) error 1
ipw_monitor: You need to read the LICENSE file in /usr/share/doc/legal/intel_ipw/.
ipw_monitor: If you agree with the license, set legal.intel_ipw.license_ack=1 in /boot/loader.conf.
module_register_init: MOD_LOAD (ipw_monitor_fw, 0xc07673c0, 0) error 1
wlan: mac acl policy registered
kbd1 at kbdmux0
cryptosoft0: <software crypto="">on motherboard
padlock0: No ACE support.
acpi0: <dell pe_sc3="">on motherboard
acpi0: [ITHREAD]
acpi0: Power Button (fixed)
Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x808-0x80b on acpi0
cpu0: <acpi cpu="">on acpi0
cpu1: <acpi cpu="">on acpi0
cpu2: <acpi cpu="">on acpi0
cpu3: <acpi cpu="">on acpi0
acpi_hpet0: <high precision="" event="" timer="">iomem 0xfed00000-0xfed003ff on acpi0
Timecounter "HPET" frequency 14318180 Hz quality 900
pcib0: <acpi host-pci="" bridge="">port 0xcf8-0xcff on acpi0
pci0: <acpi pci="" bus="">on pcib0
pcib1: <acpi pci-pci="" bridge="">at device 1.0 on pci0
pci1: <acpi pci="" bus="">on pcib1
bce0: <broadcom netxtreme="" ii="" bcm5716="" 1000base-t="" (c0)="">mem 0xd8000000-0xd9ffffff irq 36 at device 0.0 on pci1
miibus0: <mii bus="">on bce0
brgphy0: <bcm5709c 10="" 100="" 1000basetx="" phy="">PHY 1 on miibus0
brgphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto
bce0: [ITHREAD]
bce0: ASIC (0x57092008); Rev (C0); Bus (PCIe x4, 2.5Gbps); B/C (5.2.3); Flags (MSI|MFW); MFW (NCSI 2.0.11)
bce1: <broadcom netxtreme="" ii="" bcm5716="" 1000base-t="" (c0)="">mem 0xda000000-0xdbffffff irq 48 at device 0.1 on pci1
miibus1: <mii bus="">on bce1
brgphy1: <bcm5709c 10="" 100="" 1000basetx="" phy="">PHY 1 on miibus1
brgphy1:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto
bce1: [ITHREAD]
bce1: ASIC (0x57092008); Rev (C0); Bus (PCIe x4, 2.5Gbps); B/C (5.2.3); Flags (MSI|MFW); MFW (NCSI 2.0.11)
pcib2: <acpi pci-pci="" bridge="">at device 3.0 on pci0
pci2: <acpi pci="" bus="">on pcib2
mpt0: <lsilogic sas="" sata="" adapter="">port 0xfc00-0xfcff mem 0xdeaec000-0xdeaeffff,0xdeaf0000-0xdeafffff irq 32 at device 0.0 on pci2
mpt0: [ITHREAD]
mpt0: MPI Version=1.5.18.0
mpt0: Capabilities: ( RAID-0 RAID-1E RAID-1 )
mpt0: 1 Active Volume (2 Max)
mpt0: 2 Hidden Drive Members (14 Max)
pcib3: <acpi pci-pci="" bridge="">at device 7.0 on pci0
pci3: <acpi pci="" bus="">on pcib3
pcib4: <pci-pci bridge="">at device 0.0 on pci3
pci4: <pci bus="">on pcib4
pcib5: <pci-pci bridge="">at device 2.0 on pci4
pci5: <pci bus="">on pcib5
igb0: <intel(r) 1000="" pro="" network="" connection="" version="" -="" 2.0.7="">port 0xecc0-0xecdf mem 0xddfc0000-0xddfdffff,0xde000000-0xde3fffff,0xddfb8000-0xddfbbfff irq 47 at device 0.0 on pci5
igb0: Using MSIX interrupts with 5 vectors
igb0: [ITHREAD]
igb0: [ITHREAD]
igb0: [ITHREAD]
igb0: [ITHREAD]
igb0: [ITHREAD]
igb1: <intel(r) 1000="" pro="" network="" connection="" version="" -="" 2.0.7="">port 0xece0-0xecff mem 0xddfe0000-0xddffffff,0xde400000-0xde7fffff,0xddfbc000-0xddfbffff irq 46 at device 0.1 on pci5
igb1: Using MSIX interrupts with 5 vectors
igb1: [ITHREAD]
igb1: [ITHREAD]
igb1: [ITHREAD]
igb1: [ITHREAD]
igb1: [ITHREAD]
pcib6: <pci-pci bridge="">at device 4.0 on pci4
pci6: <pci bus="">on pcib6
igb2: <intel(r) 1000="" pro="" network="" connection="" version="" -="" 2.0.7="">port 0xdcc0-0xdcdf mem 0xdd3c0000-0xdd3dffff,0xdd400000-0xdd7fffff,0xdd3b8000-0xdd3bbfff irq 38 at device 0.0 on pci6
igb2: Using MSIX interrupts with 5 vectors
igb2: [ITHREAD]
igb2: [ITHREAD]
igb2: [ITHREAD]
igb2: [ITHREAD]
igb2: [ITHREAD]
igb3: <intel(r) 1000="" pro="" network="" connection="" version="" -="" 2.0.7="">port 0xdce0-0xdcff mem 0xdd3e0000-0xdd3fffff,0xdd800000-0xddbfffff,0xdd3bc000-0xdd3bffff irq 45 at device 0.1 on pci6
igb3: Using MSIX interrupts with 5 vectors
igb3: [ITHREAD]
igb3: [ITHREAD]
igb3: [ITHREAD]
igb3: [ITHREAD]
igb3: [ITHREAD]
pcib7: <acpi pci-pci="" bridge="">at device 9.0 on pci0
pci7: <acpi pci="" bus="">on pcib7
pcib8: <acpi pci-pci="" bridge="">at device 10.0 on pci0
pci8: <acpi pci="" bus="">on pcib8
pci0: <base peripheral,="" interrupt="" controller=""> at device 20.0 (no driver attached)
pci0: <base peripheral,="" interrupt="" controller=""> at device 20.1 (no driver attached)
pci0: <base peripheral,="" interrupt="" controller=""> at device 20.2 (no driver attached)
uhci0: <intel 82801ji="" (ich10)="" usb="" controller="" usb-d="">port 0xcc40-0xcc5f irq 17 at device 26.0 on pci0
uhci0: [ITHREAD]
usbus0: <intel 82801ji="" (ich10)="" usb="" controller="" usb-d="">on uhci0
uhci1: <intel 82801ji="" (ich10)="" usb="" controller="" usb-e="">port 0xcc60-0xcc7f irq 18 at device 26.1 on pci0
uhci1: [ITHREAD]
usbus1: <intel 82801ji="" (ich10)="" usb="" controller="" usb-e="">on uhci1
ehci0: <intel 82801ji="" (ich10)="" usb="" 2.0="" controller="" usb-b="">mem 0xde8fe000-0xde8fe3ff irq 19 at device 26.7 on pci0
ehci0: [ITHREAD]
usbus2: EHCI version 1.0
usbus2: <intel 82801ji="" (ich10)="" usb="" 2.0="" controller="" usb-b="">on ehci0
uhci2: <intel 82801ji="" (ich10)="" usb="" controller="" usb-a="">port 0xcc80-0xcc9f irq 21 at device 29.0 on pci0
uhci2: [ITHREAD]
usbus3: <intel 82801ji="" (ich10)="" usb="" controller="" usb-a="">on uhci2
uhci3: <intel 82801ji="" (ich10)="" usb="" controller="" usb-b="">port 0xcca0-0xccbf irq 20 at device 29.1 on pci0
uhci3: [ITHREAD]
usbus4: <intel 82801ji="" (ich10)="" usb="" controller="" usb-b="">on uhci3
uhci4: <intel 82801ji="" (ich10)="" usb="" controller="" usb-c="">port 0xccc0-0xccdf irq 21 at device 29.2 on pci0
uhci4: [ITHREAD]
usbus5: <intel 82801ji="" (ich10)="" usb="" controller="" usb-c="">on uhci4
uhci5: <intel 82801ji="" (ich10)="" usb="" controller="" usb-f="">port 0xcce0-0xccff irq 20 at device 29.3 on pci0
uhci5: [ITHREAD]
usbus6: <intel 82801ji="" (ich10)="" usb="" controller="" usb-f="">on uhci5
ehci1: <intel 82801ji="" (ich10)="" usb="" 2.0="" controller="" usb-a="">mem 0xde8ff000-0xde8ff3ff irq 21 at device 29.7 on pci0
ehci1: [ITHREAD]
usbus7: EHCI version 1.0
usbus7: <intel 82801ji="" (ich10)="" usb="" 2.0="" controller="" usb-a="">on ehci1
pcib9: <acpi pci-pci="" bridge="">at device 30.0 on pci0
pci9: <acpi pci="" bus="">on pcib9
vgapci0: <vga-compatible display="">mem 0xd7800000-0xd7ffffff,0xdc7fc000-0xdc7fffff,0xdc800000-0xdcffffff irq 19 at device 3.0 on pci9
isab0: <pci-isa bridge="">at device 31.0 on pci0
isa0: <isa bus="">on isab0
atapci0: <intel ich10="" sata300="" controller="">port 0xc8e0-0xc8e7,0xc8d0-0xc8d3,0xc8e8-0xc8ef,0xc8d4-0xc8d7,0xcc00-0xcc0f,0xcc10-0xcc1f irq 23 at device 31.2 on pci0
atapci0: [ITHREAD]
ata2: <ata 0="" channel="">on atapci0
ata2: [ITHREAD]
ata3: <ata 1="" channel="">on atapci0
ata3: [ITHREAD]
atapci1: <intel ich10="" sata300="" controller="">port 0xc8f0-0xc8f7,0xc8d8-0xc8db,0xc8f8-0xc8ff,0xc8dc-0xc8df,0xcc20-0xcc2f,0xcc30-0xcc3f irq 22 at device 31.5 on pci0
atapci1: [ITHREAD]
ata4: <ata 0="" channel="">on atapci1
ata4: [ITHREAD]
ata5: <ata 1="" channel="">on atapci1
ata5: [ITHREAD]
atrtc0: <at realtime="" clock="">port 0x70-0x7f irq 8 on acpi0
uart0: <16550 or compatible> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0
uart0: [FILTER]
uart1: <16550 or compatible> port 0x2f8-0x2ff irq 3 on acpi0
uart1: [FILTER]
pmtimer0 on isa0
orm0: <isa option="" roms="">at iomem 0xc0000-0xc7fff,0xce000-0xcefff,0xec000-0xeffff pnpid ORM0000 on isa0
sc0: <system console="">at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
vga0: <generic isa="" vga="">at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
ata0 at port 0x1f0-0x1f7,0x3f6 irq 14 on isa0
ata0: [ITHREAD]
ata1 at port 0x170-0x177,0x376 irq 15 on isa0
ata1: [ITHREAD]
atkbdc0: <keyboard controller="" (i8042)="">at port 0x60,0x64 on isa0
atkbd0: <at keyboard="">irq 1 on atkbdc0
kbd0 at atkbd0
atkbd0: [GIANT-LOCKED]
atkbd0: [ITHREAD]
ppc0: parallel port not found.
est0: <enhanced speedstep="" frequency="" control="">on cpu0
est: CPU supports Enhanced Speedstep, but is not recognized.
est: cpu_vendor GenuineIntel, msr f
device_attach: est0 attach returned 6
p4tcc0: <cpu frequency="" thermal="" control="">on cpu0
est1: <enhanced speedstep="" frequency="" control="">on cpu1
est: CPU supports Enhanced Speedstep, but is not recognized.
est: cpu_vendor GenuineIntel, msr f
device_attach: est1 attach returned 6
p4tcc1: <cpu frequency="" thermal="" control="">on cpu1
est2: <enhanced speedstep="" frequency="" control="">on cpu2
est: CPU supports Enhanced Speedstep, but is not recognized.
est: cpu_vendor GenuineIntel, msr f
device_attach: est2 attach returned 6
p4tcc2: <cpu frequency="" thermal="" control="">on cpu2
est3: <enhanced speedstep="" frequency="" control="">on cpu3
est: CPU supports Enhanced Speedstep, but is not recognized.
est: cpu_vendor GenuineIntel, msr f
device_attach: est3 attach returned 6
p4tcc3: <cpu frequency="" thermal="" control="">on cpu3
Timecounters tick every 1.000 msec
IPsec: Initialized Security Association Processing.
usbus0: 12Mbps Full Speed USB v1.0
usbus1: 12Mbps Full Speed USB v1.0
usbus2: 480Mbps High Speed USB v2.0
usbus3: 12Mbps Full Speed USB v1.0
usbus4: 12Mbps Full Speed USB v1.0
usbus5: 12Mbps Full Speed USB v1.0
usbus6: 12Mbps Full Speed USB v1.0
usbus7: 480Mbps High Speed USB v2.0
mpt0:vol0(mpt0:0:0): Settings ( Member-WCE Hot-Plug-Spares High-Priority-ReSync )
mpt0:vol0(mpt0:0:0): Using Spare Pool: 0
mpt0:vol0(mpt0:0:0): 2 Members:
      (mpt0:1:9:0): Primary Online
      (mpt0:1:1:0): Secondary Online
mpt0:vol0(mpt0:0:0): RAID-1 - Optimal
mpt0:vol0(mpt0:0:0): Status ( Enabled )
(mpt0:vol0:1): Physical (mpt0:0:1:0), Pass-thru (mpt0:1:0:0)
(mpt0:vol0:1): Online
(mpt0:vol0:0): Physical (mpt0:0:9:0), Pass-thru (mpt0:1:1:0)
(mpt0:vol0:0): Online
(xpt0:mpt0:1-1): rescan already queued
ugen0.1: <intel>at usbus0
uhub0: <intel 1="" 9="" uhci="" root="" hub,="" class="" 0,="" rev="" 1.00="" 1.00,="" addr="">on usbus0
ugen1.1: <intel>at usbus1
uhub1: <intel 1="" 9="" uhci="" root="" hub,="" class="" 0,="" rev="" 1.00="" 1.00,="" addr="">on usbus1
ugen2.1: <intel>at usbus2
uhub2: <intel 1="" 9="" ehci="" root="" hub,="" class="" 0,="" rev="" 2.00="" 1.00,="" addr="">on usbus2
ugen3.1: <intel>at usbus3
uhub3: <intel 1="" 9="" uhci="" root="" hub,="" class="" 0,="" rev="" 1.00="" 1.00,="" addr="">on usbus3
ugen4.1: <intel>at usbus4
uhub4: <intel 1="" 9="" uhci="" root="" hub,="" class="" 0,="" rev="" 1.00="" 1.00,="" addr="">on usbus4
ugen5.1: <intel>at usbus5
uhub5: <intel 1="" 9="" uhci="" root="" hub,="" class="" 0,="" rev="" 1.00="" 1.00,="" addr="">on usbus5
ugen6.1: <intel>at usbus6
uhub6: <intel 1="" 9="" uhci="" root="" hub,="" class="" 0,="" rev="" 1.00="" 1.00,="" addr="">on usbus6
ugen7.1: <intel>at usbus7
uhub7: <intel 1="" 9="" ehci="" root="" hub,="" class="" 0,="" rev="" 2.00="" 1.00,="" addr="">on usbus7
uhub0: 2 ports with 2 removable, self powered
uhub1: 2 ports with 2 removable, self powered
uhub3: 2 ports with 2 removable, self powered
uhub4: 2 ports with 2 removable, self powered
uhub5: 2 ports with 2 removable, self powered
uhub6: 2 ports with 2 removable, self powered
uhub2: 4 ports with 4 removable, self powered
uhub7: 4 ports with 4 removable, self powered
acd0: DVDROM <teac dvd-rom="" dv-28sw="" r.2a="">at ata4-master UDMA100 SATA 1.5Gb/s
ses0 at mpt0 bus 0 scbus0 target 8 lun 0
ses0: <dp backplane="" 1.10="">Fixed Enclosure Services SCSI-5 device
ses0: 300.000MB/s transfers
ses0: SCSI-3 SES Device
da0 at mpt0 bus 0 scbus0 target 0 lun 0
da0: <dell 1028="" virtual="" disk="">Fixed Direct Access SCSI-5 device
da0: 300.000MB/s transfers
da0: Command Queueing enabled
da0: 237824MB (487063552 512 byte sectors: 255H 63S/T 30318C)
pass2 at mpt0 bus 1 scbus1 target 0 lun 0
pass2: <ata wdc="" wd2502abys-1="" 3b05="">Fixed Uninstalled SCSI-5 device
pass2: 300.000MB/s transfers
pass2: Command Queueing enabled
SMP: AP CPU #1 Launched!
SMP: AP CPU #3 Launched!
SMP: AP CPU #2 Launched!
Root mount waiting for: usbus2
ugen2.2: <vendor 0x0424="">at usbus2
uhub8: <vendor 2="" 9="" 0x0424="" product="" 0x2514,="" class="" 0,="" rev="" 2.00="" 0.00,="" addr="">on usbus2
ugen0.2: <dell>at usbus0
ukbd0: <ep1 interrupt="">on usbus0
kbd2 at ukbd0
uhub8: 2 ports with 2 removable, self powered
Trying to mount root from ufs:/dev/da0s1a
pflog0: promiscuous mode enabled
bce1: link state changed to UP
interrupt                          total      rate
irq17: uhci0                          19          0
irq19: ehci0                        103          0
irq22: atapci1                        68          0
irq32: mpt0                        2244        13
cpu0: timer                      340586      1980
irq256: bce0                          1          0
irq257: bce1                        604          3
cpu1: timer                      331343      1926
cpu3: timer                      332203      1931
cpu2: timer                      332203      1931
Total                            1339374      7787

3rd Test

1 Add-In Quad Port NIC installed
BIOS Settings set to Default
Boot to LiveCD and attempt to install
I see this message go by during the boot for each Intel NIC:  igb#  Could not setup receive structures
LiveCD hangs at "Starting DHCP Service…"
Solid cursor at end of the line

This test was repeated twice with the same results

4th Test

BIOS Setting changed to Set CPU to single core
Everything Works!

R510 w 1 NIC installed & CPU = Single

dmesg; vmstat -i
Copyright 1992-2010 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 8.1-RELEASE-p2 #0: Sat Feb 26 15:29:09 EST 2011
    sullrich@FreeBSD_8.0_pfSense_2.0-snaps.pfsense.org:/usr/obj.pfSense/usr/pfSensesrc/src/sys/pfSense_SMP.8 i386
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: Intel(R) Xeon(R) CPU          E5503  @ 2.00GHz (2000.08-MHz 686-class CPU)
  Origin = "GenuineIntel"  Id = 0x106a5  Family = 6  Model = 1a  Stepping = 5
  Features=0xbfebfbff <fpu,vme,de,pse,tsc,msr,pae,mce,cx8,apic,sep,mtrr,pge,mca,cmov,pat,pse36,clflush,dts,acpi,mmx,fxsr,sse,sse2,ss,htt,tm,pbe>Features2=0x9ce3bd <sse3,dtes64,mon,ds_cpl,vmx,est,tm2,ssse3,cx16,xtpr,pdcm,dca,sse4.1,sse4.2,popcnt>AMD Features=0x28100000 <nx,rdtscp,lm>AMD Features2=0x1 <lahf>TSC: P-state invariant
real memory  = 2147483648 (2048 MB)
avail memory = 2069499904 (1973 MB)
ACPI APIC Table: <dell  pe_sc3 ="">FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs
FreeBSD/SMP: 2 package(s) x 1 core(s)
cpu0 (BSP): APIC ID: 16
cpu1 (AP): APIC ID:  0
ioapic1: Changing APIC ID to 1
ioapic0 <version 2.0="">irqs 0-23 on motherboard
ioapic1 <version 2.0="">irqs 32-55 on motherboard
wpi: You need to read the LICENSE file in /usr/share/doc/legal/intel_wpi/.
wpi: If you agree with the license, set legal.intel_wpi.license_ack=1 in /boot/loader.conf.
module_register_init: MOD_LOAD (wpi_fw, 0xc095c1e0, 0) error 1
ipw_bss: You need to read the LICENSE file in /usr/share/doc/legal/intel_ipw/.
ipw_bss: If you agree with the license, set legal.intel_ipw.license_ack=1 in /boot/loader.conf.
module_register_init: MOD_LOAD (ipw_bss_fw, 0xc0767240, 0) error 1
ipw_ibss: You need to read the LICENSE file in /usr/share/doc/legal/intel_ipw/.
ipw_ibss: If you agree with the license, set legal.intel_ipw.license_ack=1 in /boot/loader.conf.
module_register_init: MOD_LOAD (ipw_ibss_fw, 0xc0767300, 0) error 1
ipw_monitor: You need to read the LICENSE file in /usr/share/doc/legal/intel_ipw/.
ipw_monitor: If you agree with the license, set legal.intel_ipw.license_ack=1 in /boot/loader.conf.
module_register_init: MOD_LOAD (ipw_monitor_fw, 0xc07673c0, 0) error 1
wlan: mac acl policy registered
kbd1 at kbdmux0
cryptosoft0: <software crypto="">on motherboard
padlock0: No ACE support.
acpi0: <dell pe_sc3="">on motherboard
acpi0: [ITHREAD]
acpi0: Power Button (fixed)
Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x808-0x80b on acpi0
cpu0: <acpi cpu="">on acpi0
cpu1: <acpi cpu="">on acpi0
acpi_hpet0: <high precision="" event="" timer="">iomem 0xfed00000-0xfed003ff on acpi0
Timecounter "HPET" frequency 14318180 Hz quality 900
pcib0: <acpi host-pci="" bridge="">port 0xcf8-0xcff on acpi0
pci0: <acpi pci="" bus="">on pcib0
pcib1: <acpi pci-pci="" bridge="">at device 1.0 on pci0
pci1: <acpi pci="" bus="">on pcib1
bce0: <broadcom netxtreme="" ii="" bcm5716="" 1000base-t="" (c0)="">mem 0xd8000000-0xd9ffffff irq 36 at device 0.0 on pci1
miibus0: <mii bus="">on bce0
brgphy0: <bcm5709c 10="" 100="" 1000basetx="" phy="">PHY 1 on miibus0
brgphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto
bce0: [ITHREAD]
bce0: ASIC (0x57092008); Rev (C0); Bus (PCIe x4, 2.5Gbps); B/C (5.2.3); Flags (MSI|MFW); MFW (NCSI 2.0.11)
bce1: <broadcom netxtreme="" ii="" bcm5716="" 1000base-t="" (c0)="">mem 0xda000000-0xdbffffff irq 48 at device 0.1 on pci1
miibus1: <mii bus="">on bce1
brgphy1: <bcm5709c 10="" 100="" 1000basetx="" phy="">PHY 1 on miibus1
brgphy1:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto
bce1: [ITHREAD]
bce1: ASIC (0x57092008); Rev (C0); Bus (PCIe x4, 2.5Gbps); B/C (5.2.3); Flags (MSI|MFW); MFW (NCSI 2.0.11)
pcib2: <acpi pci-pci="" bridge="">at device 3.0 on pci0
pci2: <acpi pci="" bus="">on pcib2
mpt0: <lsilogic sas="" sata="" adapter="">port 0xfc00-0xfcff mem 0xdeaec000-0xdeaeffff,0xdeaf0000-0xdeafffff irq 32 at device 0.0 on pci2
mpt0: [ITHREAD]
mpt0: MPI Version=1.5.18.0
mpt0: Capabilities: ( RAID-0 RAID-1E RAID-1 )
mpt0: 1 Active Volume (2 Max)
mpt0: 2 Hidden Drive Members (14 Max)
pcib3: <acpi pci-pci="" bridge="">at device 7.0 on pci0
pci3: <acpi pci="" bus="">on pcib3
pcib4: <pci-pci bridge="">at device 0.0 on pci3
pci4: <pci bus="">on pcib4
pcib5: <pci-pci bridge="">at device 2.0 on pci4
pci5: <pci bus="">on pcib5
igb0: <intel(r) 1000="" pro="" network="" connection="" version="" -="" 2.0.7="">port 0xecc0-0xecdf mem 0xddfc0000-0xddfdffff,0xde000000-0xde3fffff,0xddfb8000-0xddfbbfff irq 47 at device 0.0 on pci5
igb0: Using MSIX interrupts with 3 vectors
igb0: [ITHREAD]
igb0: [ITHREAD]
igb0: [ITHREAD]
igb1: <intel(r) 1000="" pro="" network="" connection="" version="" -="" 2.0.7="">port 0xece0-0xecff mem 0xddfe0000-0xddffffff,0xde400000-0xde7fffff,0xddfbc000-0xddfbffff irq 46 at device 0.1 on pci5
igb1: Using MSIX interrupts with 3 vectors
igb1: [ITHREAD]
igb1: [ITHREAD]
igb1: [ITHREAD]
pcib6: <pci-pci bridge="">at device 4.0 on pci4
pci6: <pci bus="">on pcib6
igb2: <intel(r) 1000="" pro="" network="" connection="" version="" -="" 2.0.7="">port 0xdcc0-0xdcdf mem 0xdd3c0000-0xdd3dffff,0xdd400000-0xdd7fffff,0xdd3b8000-0xdd3bbfff irq 38 at device 0.0 on pci6
igb2: Using MSIX interrupts with 3 vectors
igb2: [ITHREAD]
igb2: [ITHREAD]
igb2: [ITHREAD]
igb3: <intel(r) 1000="" pro="" network="" connection="" version="" -="" 2.0.7="">port 0xdce0-0xdcff mem 0xdd3e0000-0xdd3fffff,0xdd800000-0xddbfffff,0xdd3bc000-0xdd3bffff irq 45 at device 0.1 on pci6
igb3: Using MSIX interrupts with 3 vectors
igb3: [ITHREAD]
igb3: [ITHREAD]
igb3: [ITHREAD]
pcib7: <acpi pci-pci="" bridge="">at device 9.0 on pci0
pci7: <acpi pci="" bus="">on pcib7
pcib8: <acpi pci-pci="" bridge="">at device 10.0 on pci0
pci8: <acpi pci="" bus="">on pcib8
pci0: <base peripheral,="" interrupt="" controller=""> at device 20.0 (no driver attached)
pci0: <base peripheral,="" interrupt="" controller=""> at device 20.1 (no driver attached)
pci0: <base peripheral,="" interrupt="" controller=""> at device 20.2 (no driver attached)
uhci0: <intel 82801ji="" (ich10)="" usb="" controller="" usb-d="">port 0xcc40-0xcc5f irq 17 at device 26.0 on pci0
uhci0: [ITHREAD]
usbus0: <intel 82801ji="" (ich10)="" usb="" controller="" usb-d="">on uhci0
uhci1: <intel 82801ji="" (ich10)="" usb="" controller="" usb-e="">port 0xcc60-0xcc7f irq 18 at device 26.1 on pci0
uhci1: [ITHREAD]
usbus1: <intel 82801ji="" (ich10)="" usb="" controller="" usb-e="">on uhci1
ehci0: <intel 82801ji="" (ich10)="" usb="" 2.0="" controller="" usb-b="">mem 0xde8fe000-0xde8fe3ff irq 19 at device 26.7 on pci0
ehci0: [ITHREAD]
usbus2: EHCI version 1.0
usbus2: <intel 82801ji="" (ich10)="" usb="" 2.0="" controller="" usb-b="">on ehci0
uhci2: <intel 82801ji="" (ich10)="" usb="" controller="" usb-a="">port 0xcc80-0xcc9f irq 21 at device 29.0 on pci0
uhci2: [ITHREAD]
usbus3: <intel 82801ji="" (ich10)="" usb="" controller="" usb-a="">on uhci2
uhci3: <intel 82801ji="" (ich10)="" usb="" controller="" usb-b="">port 0xcca0-0xccbf irq 20 at device 29.1 on pci0
uhci3: [ITHREAD]
usbus4: <intel 82801ji="" (ich10)="" usb="" controller="" usb-b="">on uhci3
uhci4: <intel 82801ji="" (ich10)="" usb="" controller="" usb-c="">port 0xccc0-0xccdf irq 21 at device 29.2 on pci0
uhci4: [ITHREAD]
usbus5: <intel 82801ji="" (ich10)="" usb="" controller="" usb-c="">on uhci4
uhci5: <intel 82801ji="" (ich10)="" usb="" controller="" usb-f="">port 0xcce0-0xccff irq 20 at device 29.3 on pci0
uhci5: [ITHREAD]
usbus6: <intel 82801ji="" (ich10)="" usb="" controller="" usb-f="">on uhci5
ehci1: <intel 82801ji="" (ich10)="" usb="" 2.0="" controller="" usb-a="">mem 0xde8ff000-0xde8ff3ff irq 21 at device 29.7 on pci0
ehci1: [ITHREAD]
usbus7: EHCI version 1.0
usbus7: <intel 82801ji="" (ich10)="" usb="" 2.0="" controller="" usb-a="">on ehci1
pcib9: <acpi pci-pci="" bridge="">at device 30.0 on pci0
pci9: <acpi pci="" bus="">on pcib9
vgapci0: <vga-compatible display="">mem 0xd7800000-0xd7ffffff,0xdc7fc000-0xdc7fffff,0xdc800000-0xdcffffff irq 19 at device 3.0 on pci9
isab0: <pci-isa bridge="">at device 31.0 on pci0
isa0: <isa bus="">on isab0
atapci0: <intel ich10="" sata300="" controller="">port 0xc8e0-0xc8e7,0xc8d0-0xc8d3,0xc8e8-0xc8ef,0xc8d4-0xc8d7,0xcc00-0xcc0f,0xcc10-0xcc1f irq 23 at device 31.2 on pci0
atapci0: [ITHREAD]
ata2: <ata 0="" channel="">on atapci0
ata2: [ITHREAD]
ata3: <ata 1="" channel="">on atapci0
ata3: [ITHREAD]
atapci1: <intel ich10="" sata300="" controller="">port 0xc8f0-0xc8f7,0xc8d8-0xc8db,0xc8f8-0xc8ff,0xc8dc-0xc8df,0xcc20-0xcc2f,0xcc30-0xcc3f irq 22 at device 31.5 on pci0
atapci1: [ITHREAD]
ata4: <ata 0="" channel="">on atapci1
ata4: [ITHREAD]
ata5: <ata 1="" channel="">on atapci1
ata5: [ITHREAD]
atrtc0: <at realtime="" clock="">port 0x70-0x7f irq 8 on acpi0
uart0: <16550 or compatible> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0
uart0: [FILTER]
uart1: <16550 or compatible> port 0x2f8-0x2ff irq 3 on acpi0
uart1: [FILTER]
pmtimer0 on isa0
orm0: <isa option="" roms="">at iomem 0xc0000-0xc7fff,0xce000-0xcefff,0xec000-0xeffff pnpid ORM0000 on isa0
sc0: <system console="">at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
vga0: <generic isa="" vga="">at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
ata0 at port 0x1f0-0x1f7,0x3f6 irq 14 on isa0
ata0: [ITHREAD]
ata1 at port 0x170-0x177,0x376 irq 15 on isa0
ata1: [ITHREAD]
atkbdc0: <keyboard controller="" (i8042)="">at port 0x60,0x64 on isa0
atkbd0: <at keyboard="">irq 1 on atkbdc0
kbd0 at atkbd0
atkbd0: [GIANT-LOCKED]
atkbd0: [ITHREAD]
ppc0: parallel port not found.
est0: <enhanced speedstep="" frequency="" control="">on cpu0
est: CPU supports Enhanced Speedstep, but is not recognized.
est: cpu_vendor GenuineIntel, msr f
device_attach: est0 attach returned 6
p4tcc0: <cpu frequency="" thermal="" control="">on cpu0
est1: <enhanced speedstep="" frequency="" control="">on cpu1
est: CPU supports Enhanced Speedstep, but is not recognized.
est: cpu_vendor GenuineIntel, msr f
device_attach: est1 attach returned 6
p4tcc1: <cpu frequency="" thermal="" control="">on cpu1
Timecounters tick every 1.000 msec
IPsec: Initialized Security Association Processing.
usbus0: 12Mbps Full Speed USB v1.0
usbus1: 12Mbps Full Speed USB v1.0
usbus2: 480Mbps High Speed USB v2.0
usbus3: 12Mbps Full Speed USB v1.0
usbus4: 12Mbps Full Speed USB v1.0
usbus5: 12Mbps Full Speed USB v1.0
usbus6: 12Mbps Full Speed USB v1.0
usbus7: 480Mbps High Speed USB v2.0
mpt0:vol0(mpt0:0:0): Settings ( Member-WCE Hot-Plug-Spares High-Priority-ReSync )
mpt0:vol0(mpt0:0:0): Using Spare Pool: 0
mpt0:vol0(mpt0:0:0): 2 Members:
      (mpt0:1:9:0): Primary Online
      (mpt0:1:1:0): Secondary Online
mpt0:vol0(mpt0:0:0): RAID-1 - Optimal
mpt0:vol0(mpt0:0:0): Status ( Enabled )
(mpt0:vol0:1): Physical (mpt0:0:1:0), Pass-thru (mpt0:1:0:0)
(mpt0:vol0:1): Online
(mpt0:vol0:0): Physical (mpt0:0:9:0), Pass-thru (mpt0:1:1:0)
(mpt0:vol0:0): Online
(xpt0:mpt0:1-1): rescan already queued
ugen0.1: <intel>at usbus0
uhub0: <intel 1="" 9="" uhci="" root="" hub,="" class="" 0,="" rev="" 1.00="" 1.00,="" addr="">on usbus0
ugen1.1: <intel>at usbus1
uhub1: <intel 1="" 9="" uhci="" root="" hub,="" class="" 0,="" rev="" 1.00="" 1.00,="" addr="">on usbus1
ugen2.1: <intel>at usbus2
uhub2: <intel 1="" 9="" ehci="" root="" hub,="" class="" 0,="" rev="" 2.00="" 1.00,="" addr="">on usbus2
ugen3.1: <intel>at usbus3
uhub3: <intel 1="" 9="" uhci="" root="" hub,="" class="" 0,="" rev="" 1.00="" 1.00,="" addr="">on usbus3
ugen4.1: <intel>at usbus4
uhub4: <intel 1="" 9="" uhci="" root="" hub,="" class="" 0,="" rev="" 1.00="" 1.00,="" addr="">on usbus4
ugen5.1: <intel>at usbus5
uhub5: <intel 1="" 9="" uhci="" root="" hub,="" class="" 0,="" rev="" 1.00="" 1.00,="" addr="">on usbus5
ugen6.1: <intel>at usbus6
uhub6: <intel 1="" 9="" uhci="" root="" hub,="" class="" 0,="" rev="" 1.00="" 1.00,="" addr="">on usbus6
ugen7.1: <intel>at usbus7
uhub7: <intel 1="" 9="" ehci="" root="" hub,="" class="" 0,="" rev="" 2.00="" 1.00,="" addr="">on usbus7
uhub0: 2 ports with 2 removable, self powered
uhub1: 2 ports with 2 removable, self powered
uhub3: 2 ports with 2 removable, self powered
uhub4: 2 ports with 2 removable, self powered
uhub5: 2 ports with 2 removable, self powered
uhub6: 2 ports with 2 removable, self powered
uhub2: 4 ports with 4 removable, self powered
uhub7: 4 ports with 4 removable, self powered
acd0: DVDROM <teac dvd-rom="" dv-28sw="" r.2a="">at ata4-master UDMA100 SATA 1.5Gb/s
ses0 at mpt0 bus 0 scbus0 target 8 lun 0
ses0: <dp backplane="" 1.10="">Fixed Enclosure Services SCSI-5 device
ses0: 300.000MB/s transfers
ses0: SCSI-3 SES Device
da0 at mpt0 bus 0 scbus0 target 0 lun 0
da0: <dell 1028="" virtual="" disk="">Fixed Direct Access SCSI-5 device
da0: 300.000MB/s transfers
da0: Command Queueing enabled
da0: 237824MB (487063552 512 byte sectors: 255H 63S/T 30318C)
pass2 at mpt0 bus 1 scbus1 target 0 lun 0
pass2: <ata wdc="" wd2502abys-1="" 3b05="">Fixed Uninstalled SCSI-5 device
pass2: 300.000MB/s transfers
pass2: Command Queueing enabled
SMP: AP CPU #1 Launched!
Root mount waiting for: usbus2
ugen2.2: <vendor 0x0424="">at usbus2
uhub8: <vendor 2="" 9="" 0x0424="" product="" 0x2514,="" class="" 0,="" rev="" 2.00="" 0.00,="" addr="">on usbus2
ugen0.2: <dell>at usbus0
ukbd0: <ep1 interrupt="">on usbus0
kbd2 at ukbd0
Root mount waiting for: usbus2
uhub8: 4 ports with 4 removable, self powered
Trying to mount root from ufs:/dev/da0s1a
pflog0: promiscuous mode enabled
bce1: link state changed to UP
igb0: link state changed to UP
igb1: link state changed to UP
igb1: link state changed to DOWN
igb0: link state changed to DOWN
igb1: link state changed to UP
igb0: link state changed to UP
interrupt                          total      rate
irq17: uhci0                          70          0
irq19: ehci0                        827          1
irq22: atapci1                        68          0
irq32: mpt0                        3087          3
cpu0: timer                      1603346      1991
irq256: bce0                          1          0
irq257: bce1                        492          0
irq258: igb0:que 0                    20          0
irq260: igb0:link                      2          0
irq261: igb1:que 0                    20          0
irq263: igb1:link                      2          0
cpu1: timer                      1590708      1976
Total                            3198643      3973

5th Test

Install 2nd Add-in Quad Port NIC to already installed pfSense
Assign Interfaces
Everything Works!

R510 With both NICs installed, CPU = Single

$ dmesg; vmstat -i
Copyright 1992-2010 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 8.1-RELEASE-p2 #0: Sat Feb 26 15:29:09 EST 2011
    sullrich@FreeBSD_8.0_pfSense_2.0-snaps.pfsense.org:/usr/obj.pfSense/usr/pfSensesrc/src/sys/pfSense_SMP.8 i386
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: Intel(R) Xeon(R) CPU          E5503  @ 2.00GHz (2000.08-MHz 686-class CPU)
  Origin = "GenuineIntel"  Id = 0x106a5  Family = 6  Model = 1a  Stepping = 5
  Features=0xbfebfbff <fpu,vme,de,pse,tsc,msr,pae,mce,cx8,apic,sep,mtrr,pge,mca,cmov,pat,pse36,clflush,dts,acpi,mmx,fxsr,sse,sse2,ss,htt,tm,pbe>Features2=0x9ce3bd <sse3,dtes64,mon,ds_cpl,vmx,est,tm2,ssse3,cx16,xtpr,pdcm,dca,sse4.1,sse4.2,popcnt>AMD Features=0x28100000 <nx,rdtscp,lm>AMD Features2=0x1 <lahf>TSC: P-state invariant
real memory  = 2147483648 (2048 MB)
avail memory = 2069499904 (1973 MB)
ACPI APIC Table: <dell  pe_sc3 ="">FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs
FreeBSD/SMP: 2 package(s) x 1 core(s)
cpu0 (BSP): APIC ID: 16
cpu1 (AP): APIC ID:  0
ioapic1: Changing APIC ID to 1
ioapic0 <version 2.0="">irqs 0-23 on motherboard
ioapic1 <version 2.0="">irqs 32-55 on motherboard
wpi: You need to read the LICENSE file in /usr/share/doc/legal/intel_wpi/.
wpi: If you agree with the license, set legal.intel_wpi.license_ack=1 in /boot/loader.conf.
module_register_init: MOD_LOAD (wpi_fw, 0xc095c1e0, 0) error 1
ipw_bss: You need to read the LICENSE file in /usr/share/doc/legal/intel_ipw/.
ipw_bss: If you agree with the license, set legal.intel_ipw.license_ack=1 in /boot/loader.conf.
module_register_init: MOD_LOAD (ipw_bss_fw, 0xc0767240, 0) error 1
ipw_ibss: You need to read the LICENSE file in /usr/share/doc/legal/intel_ipw/.
ipw_ibss: If you agree with the license, set legal.intel_ipw.license_ack=1 in /boot/loader.conf.
module_register_init: MOD_LOAD (ipw_ibss_fw, 0xc0767300, 0) error 1
ipw_monitor: You need to read the LICENSE file in /usr/share/doc/legal/intel_ipw/.
ipw_monitor: If you agree with the license, set legal.intel_ipw.license_ack=1 in /boot/loader.conf.
module_register_init: MOD_LOAD (ipw_monitor_fw, 0xc07673c0, 0) error 1
wlan: mac acl policy registered
kbd1 at kbdmux0
cryptosoft0: <software crypto="">on motherboard
padlock0: No ACE support.
acpi0: <dell pe_sc3="">on motherboard
acpi0: [ITHREAD]
acpi0: Power Button (fixed)
Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x808-0x80b on acpi0
cpu0: <acpi cpu="">on acpi0
cpu1: <acpi cpu="">on acpi0
acpi_hpet0: <high precision="" event="" timer="">iomem 0xfed00000-0xfed003ff on acpi0
Timecounter "HPET" frequency 14318180 Hz quality 900
pcib0: <acpi host-pci="" bridge="">port 0xcf8-0xcff on acpi0
pci0: <acpi pci="" bus="">on pcib0
pcib1: <acpi pci-pci="" bridge="">at device 1.0 on pci0
pci1: <acpi pci="" bus="">on pcib1
bce0: <broadcom netxtreme="" ii="" bcm5716="" 1000base-t="" (c0)="">mem 0xd6000000-0xd7ffffff irq 36 at device 0.0 on pci1
miibus0: <mii bus="">on bce0
brgphy0: <bcm5709c 10="" 100="" 1000basetx="" phy="">PHY 1 on miibus0
brgphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto
bce0: [ITHREAD]
bce0: ASIC (0x57092008); Rev (C0); Bus (PCIe x4, 2.5Gbps); B/C (5.2.3); Flags (MSI|MFW); MFW (NCSI 2.0.11)
bce1: <broadcom netxtreme="" ii="" bcm5716="" 1000base-t="" (c0)="">mem 0xd8000000-0xd9ffffff irq 48 at device 0.1 on pci1
miibus1: <mii bus="">on bce1
brgphy1: <bcm5709c 10="" 100="" 1000basetx="" phy="">PHY 1 on miibus1
brgphy1:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto
bce1: [ITHREAD]
bce1: ASIC (0x57092008); Rev (C0); Bus (PCIe x4, 2.5Gbps); B/C (5.2.3); Flags (MSI|MFW); MFW (NCSI 2.0.11)
pcib2: <acpi pci-pci="" bridge="">at device 3.0 on pci0
pci2: <acpi pci="" bus="">on pcib2
mpt0: <lsilogic sas="" sata="" adapter="">port 0xfc00-0xfcff mem 0xde2ec000-0xde2effff,0xde2f0000-0xde2fffff irq 32 at device 0.0 on pci2
mpt0: [ITHREAD]
mpt0: MPI Version=1.5.18.0
mpt0: Capabilities: ( RAID-0 RAID-1E RAID-1 )
mpt0: 1 Active Volume (2 Max)
mpt0: 2 Hidden Drive Members (14 Max)
pcib3: <acpi pci-pci="" bridge="">at device 7.0 on pci0
pci3: <acpi pci="" bus="">on pcib3
pcib4: <pci-pci bridge="">at device 0.0 on pci3
pci4: <pci bus="">on pcib4
pcib5: <pci-pci bridge="">at device 2.0 on pci4
pci5: <pci bus="">on pcib5
igb0: <intel(r) 1000="" pro="" network="" connection="" version="" -="" 2.0.7="">port 0xecc0-0xecdf mem 0xdbfc0000-0xdbfdffff,0xdc000000-0xdc3fffff,0xdbfb8000-0xdbfbbfff irq 47 at device 0.0 on pci5
igb0: Using MSIX interrupts with 3 vectors
igb0: [ITHREAD]
igb0: [ITHREAD]
igb0: [ITHREAD]
igb1: <intel(r) 1000="" pro="" network="" connection="" version="" -="" 2.0.7="">port 0xece0-0xecff mem 0xdbfe0000-0xdbffffff,0xdc400000-0xdc7fffff,0xdbfbc000-0xdbfbffff irq 46 at device 0.1 on pci5
igb1: Using MSIX interrupts with 3 vectors
igb1: [ITHREAD]
igb1: [ITHREAD]
igb1: [ITHREAD]
pcib6: <pci-pci bridge="">at device 4.0 on pci4
pci6: <pci bus="">on pcib6
igb2: <intel(r) 1000="" pro="" network="" connection="" version="" -="" 2.0.7="">port 0xdcc0-0xdcdf mem 0xdb3c0000-0xdb3dffff,0xdb400000-0xdb7fffff,0xdb3b8000-0xdb3bbfff irq 38 at device 0.0 on pci6
igb2: Using MSIX interrupts with 3 vectors
igb2: [ITHREAD]
igb2: [ITHREAD]
igb2: [ITHREAD]
igb3: <intel(r) 1000="" pro="" network="" connection="" version="" -="" 2.0.7="">port 0xdce0-0xdcff mem 0xdb3e0000-0xdb3fffff,0xdb800000-0xdbbfffff,0xdb3bc000-0xdb3bffff irq 45 at device 0.1 on pci6
igb3: Using MSIX interrupts with 3 vectors
igb3: [ITHREAD]
igb3: [ITHREAD]
igb3: [ITHREAD]
pcib7: <acpi pci-pci="" bridge="">at device 9.0 on pci0
pci7: <acpi pci="" bus="">on pcib7
pcib8: <pci-pci bridge="">at device 0.0 on pci7
pci8: <pci bus="">on pcib8
pcib9: <pci-pci bridge="">at device 2.0 on pci8
pci9: <pci bus="">on pcib9
igb4: <intel(r) 1000="" pro="" network="" connection="" version="" -="" 2.0.7="">port 0xccc0-0xccdf mem 0xdd7c0000-0xdd7dffff,0xdd800000-0xddbfffff,0xdd7b8000-0xdd7bbfff irq 55 at device 0.0 on pci9
igb4: Using MSIX interrupts with 3 vectors
igb4: [ITHREAD]
igb4: [ITHREAD]
igb4: [ITHREAD]
igb5: <intel(r) 1000="" pro="" network="" connection="" version="" -="" 2.0.7="">port 0xcce0-0xccff mem 0xdd7e0000-0xdd7fffff,0xddc00000-0xddffffff,0xdd7bc000-0xdd7bffff irq 49 at device 0.1 on pci9
igb5: Using MSIX interrupts with 3 vectors
igb5: [ITHREAD]
igb5: [ITHREAD]
igb5: [ITHREAD]
pcib10: <pci-pci bridge="">at device 4.0 on pci8
pci10: <pci bus="">on pcib10
igb6: <intel(r) 1000="" pro="" network="" connection="" version="" -="" 2.0.7="">port 0xbcc0-0xbcdf mem 0xdcbc0000-0xdcbdffff,0xdcc00000-0xdcffffff,0xdcbb8000-0xdcbbbfff irq 40 at device 0.0 on pci10
igb6: Using MSIX interrupts with 3 vectors
igb6: [ITHREAD]
igb6: [ITHREAD]
igb6: [ITHREAD]
igb7: <intel(r) 1000="" pro="" network="" connection="" version="" -="" 2.0.7="">port 0xbce0-0xbcff mem 0xdcbe0000-0xdcbfffff,0xdd000000-0xdd3fffff,0xdcbbc000-0xdcbbffff irq 50 at device 0.1 on pci10
igb7: Using MSIX interrupts with 3 vectors
igb7: [ITHREAD]
igb7: [ITHREAD]
igb7: [ITHREAD]
pcib11: <acpi pci-pci="" bridge="">at device 10.0 on pci0
pci11: <acpi pci="" bus="">on pcib11
pci0: <base peripheral,="" interrupt="" controller=""> at device 20.0 (no driver attached)
pci0: <base peripheral,="" interrupt="" controller=""> at device 20.1 (no driver attached)
pci0: <base peripheral,="" interrupt="" controller=""> at device 20.2 (no driver attached)
uhci0: <intel 82801ji="" (ich10)="" usb="" controller="" usb-d="">port 0xac40-0xac5f irq 17 at device 26.0 on pci0
uhci0: [ITHREAD]
usbus0: <intel 82801ji="" (ich10)="" usb="" controller="" usb-d="">on uhci0
uhci1: <intel 82801ji="" (ich10)="" usb="" controller="" usb-e="">port 0xac60-0xac7f irq 18 at device 26.1 on pci0
uhci1: [ITHREAD]
usbus1: <intel 82801ji="" (ich10)="" usb="" controller="" usb-e="">on uhci1
ehci0: <intel 82801ji="" (ich10)="" usb="" 2.0="" controller="" usb-b="">mem 0xde0fe000-0xde0fe3ff irq 19 at device 26.7 on pci0
ehci0: [ITHREAD]
usbus2: EHCI version 1.0
usbus2: <intel 82801ji="" (ich10)="" usb="" 2.0="" controller="" usb-b="">on ehci0
uhci2: <intel 82801ji="" (ich10)="" usb="" controller="" usb-a="">port 0xac80-0xac9f irq 21 at device 29.0 on pci0
uhci2: [ITHREAD]
usbus3: <intel 82801ji="" (ich10)="" usb="" controller="" usb-a="">on uhci2
uhci3: <intel 82801ji="" (ich10)="" usb="" controller="" usb-b="">port 0xaca0-0xacbf irq 20 at device 29.1 on pci0
uhci3: [ITHREAD]
usbus4: <intel 82801ji="" (ich10)="" usb="" controller="" usb-b="">on uhci3
uhci4: <intel 82801ji="" (ich10)="" usb="" controller="" usb-c="">port 0xacc0-0xacdf irq 21 at device 29.2 on pci0
uhci4: [ITHREAD]
usbus5: <intel 82801ji="" (ich10)="" usb="" controller="" usb-c="">on uhci4
uhci5: <intel 82801ji="" (ich10)="" usb="" controller="" usb-f="">port 0xace0-0xacff irq 20 at device 29.3 on pci0
uhci5: [ITHREAD]
usbus6: <intel 82801ji="" (ich10)="" usb="" controller="" usb-f="">on uhci5
ehci1: <intel 82801ji="" (ich10)="" usb="" 2.0="" controller="" usb-a="">mem 0xde0ff000-0xde0ff3ff irq 21 at device 29.7 on pci0
ehci1: [ITHREAD]
usbus7: EHCI version 1.0
usbus7: <intel 82801ji="" (ich10)="" usb="" 2.0="" controller="" usb-a="">on ehci1
pcib12: <acpi pci-pci="" bridge="">at device 30.0 on pci0
pci12: <acpi pci="" bus="">on pcib12
vgapci0: <vga-compatible display="">mem 0xd5800000-0xd5ffffff,0xda7fc000-0xda7fffff,0xda800000-0xdaffffff irq 19 at device 3.0 on pci12
isab0: <pci-isa bridge="">at device 31.0 on pci0
isa0: <isa bus="">on isab0
atapci0: <intel ich10="" sata300="" controller="">port 0xa8e0-0xa8e7,0xa8d0-0xa8d3,0xa8e8-0xa8ef,0xa8d4-0xa8d7,0xac00-0xac0f,0xac10-0xac1f irq 23 at device 31.2 on pci0
atapci0: [ITHREAD]
ata2: <ata 0="" channel="">on atapci0
ata2: [ITHREAD]
ata3: <ata 1="" channel="">on atapci0
ata3: [ITHREAD]
atapci1: <intel ich10="" sata300="" controller="">port 0xa8f0-0xa8f7,0xa8d8-0xa8db,0xa8f8-0xa8ff,0xa8dc-0xa8df,0xac20-0xac2f,0xac30-0xac3f irq 22 at device 31.5 on pci0
atapci1: [ITHREAD]
ata4: <ata 0="" channel="">on atapci1
ata4: [ITHREAD]
ata5: <ata 1="" channel="">on atapci1
ata5: [ITHREAD]
atrtc0: <at realtime="" clock="">port 0x70-0x7f irq 8 on acpi0
uart0: <16550 or compatible> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0
uart0: [FILTER]
uart1: <16550 or compatible> port 0x2f8-0x2ff irq 3 on acpi0
uart1: [FILTER]
pmtimer0 on isa0
orm0: <isa option="" roms="">at iomem 0xc0000-0xc7fff,0xce000-0xcefff,0xec000-0xeffff pnpid ORM0000 on isa0
sc0: <system console="">at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
vga0: <generic isa="" vga="">at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
ata0 at port 0x1f0-0x1f7,0x3f6 irq 14 on isa0
ata0: [ITHREAD]
ata1 at port 0x170-0x177,0x376 irq 15 on isa0
ata1: [ITHREAD]
atkbdc0: <keyboard controller="" (i8042)="">at port 0x60,0x64 on isa0
atkbd0: <at keyboard="">irq 1 on atkbdc0
kbd0 at atkbd0
atkbd0: [GIANT-LOCKED]
atkbd0: [ITHREAD]
ppc0: parallel port not found.
est0: <enhanced speedstep="" frequency="" control="">on cpu0
est: CPU supports Enhanced Speedstep, but is not recognized.
est: cpu_vendor GenuineIntel, msr f
device_attach: est0 attach returned 6
p4tcc0: <cpu frequency="" thermal="" control="">on cpu0
est1: <enhanced speedstep="" frequency="" control="">on cpu1
est: CPU supports Enhanced Speedstep, but is not recognized.
est: cpu_vendor GenuineIntel, msr f
device_attach: est1 attach returned 6
p4tcc1: <cpu frequency="" thermal="" control="">on cpu1
Timecounters tick every 1.000 msec
IPsec: Initialized Security Association Processing.
usbus0: 12Mbps Full Speed USB v1.0
usbus1: 12Mbps Full Speed USB v1.0
usbus2: 480Mbps High Speed USB v2.0
usbus3: 12Mbps Full Speed USB v1.0
usbus4: 12Mbps Full Speed USB v1.0
usbus5: 12Mbps Full Speed USB v1.0
usbus6: 12Mbps Full Speed USB v1.0
usbus7: 480Mbps High Speed USB v2.0
mpt0:vol0(mpt0:0:0): Settings ( Member-WCE Hot-Plug-Spares High-Priority-ReSync )
mpt0:vol0(mpt0:0:0): Using Spare Pool: 0
mpt0:vol0(mpt0:0:0): 2 Members:
      (mpt0:1:9:0): Primary Online
      (mpt0:1:1:0): Secondary Online
mpt0:vol0(mpt0:0:0): RAID-1 - Optimal
mpt0:vol0(mpt0:0:0): Status ( Enabled )
(mpt0:vol0:1): Physical (mpt0:0:1:0), Pass-thru (mpt0:1:0:0)
(mpt0:vol0:1): Online
(mpt0:vol0:0): Physical (mpt0:0:9:0), Pass-thru (mpt0:1:1:0)
(mpt0:vol0:0): Online
(xpt0:mpt0:1-1): rescan already queued
ugen0.1: <intel>at usbus0
uhub0: <intel 1="" 9="" uhci="" root="" hub,="" class="" 0,="" rev="" 1.00="" 1.00,="" addr="">on usbus0
ugen1.1: <intel>at usbus1
uhub1: <intel 1="" 9="" uhci="" root="" hub,="" class="" 0,="" rev="" 1.00="" 1.00,="" addr="">on usbus1
ugen2.1: <intel>at usbus2
uhub2: <intel 1="" 9="" ehci="" root="" hub,="" class="" 0,="" rev="" 2.00="" 1.00,="" addr="">on usbus2
ugen3.1: <intel>at usbus3
uhub3: <intel 1="" 9="" uhci="" root="" hub,="" class="" 0,="" rev="" 1.00="" 1.00,="" addr="">on usbus3
ugen4.1: <intel>at usbus4
uhub4: <intel 1="" 9="" uhci="" root="" hub,="" class="" 0,="" rev="" 1.00="" 1.00,="" addr="">on usbus4
ugen5.1: <intel>at usbus5
uhub5: <intel 1="" 9="" uhci="" root="" hub,="" class="" 0,="" rev="" 1.00="" 1.00,="" addr="">on usbus5
ugen6.1: <intel>at usbus6
uhub6: <intel 1="" 9="" uhci="" root="" hub,="" class="" 0,="" rev="" 1.00="" 1.00,="" addr="">on usbus6
ugen7.1: <intel>at usbus7
uhub7: <intel 1="" 9="" ehci="" root="" hub,="" class="" 0,="" rev="" 2.00="" 1.00,="" addr="">on usbus7
uhub0: 2 ports with 2 removable, self powered
uhub1: 2 ports with 2 removable, self powered
uhub3: 2 ports with 2 removable, self powered
uhub4: 2 ports with 2 removable, self powered
uhub5: 2 ports with 2 removable, self powered
uhub6: 2 ports with 2 removable, self powered
uhub2: 4 ports with 4 removable, self powered
uhub7: 4 ports with 4 removable, self powered
acd0: DVDROM <teac dvd-rom="" dv-28sw="" r.2a="">at ata4-master UDMA100 SATA 1.5Gb/s
ses0 at mpt0 bus 0 scbus0 target 8 lun 0
ses0: <dp backplane="" 1.10="">Fixed Enclosure Services SCSI-5 device
ses0: 300.000MB/s transfers
ses0: SCSI-3 SES Device
da0 at mpt0 bus 0 scbus0 target 0 lun 0
da0: <dell 1028="" virtual="" disk="">Fixed Direct Access SCSI-5 device
da0: 300.000MB/s transfers
da0: Command Queueing enabled
da0: 237824MB (487063552 512 byte sectors: 255H 63S/T 30318C)
pass2 at mpt0 bus 1 scbus1 target 0 lun 0
pass2: <ata wdc="" wd2502abys-1="" 3b05="">Fixed Uninstalled SCSI-5 device
pass2: 300.000MB/s transfers
pass2: Command Queueing enabled
SMP: AP CPU #1 Launched!
Root mount waiting for: usbus2
ugen2.2: <vendor 0x0424="">at usbus2
uhub8: <vendor 2="" 9="" 0x0424="" product="" 0x2514,="" class="" 0,="" rev="" 2.00="" 0.00,="" addr="">on usbus2
ugen0.2: <dell>at usbus0
ukbd0: <ep1 interrupt="">on usbus0
kbd2 at ukbd0
Root mount waiting for: usbus2
uhub8: 4 ports with 4 removable, self powered
Trying to mount root from ufs:/dev/da0s1a
pflog0: promiscuous mode enabled
bce1: link state changed to UP
interrupt                          total      rate
irq17: uhci0                          19          0
irq19: ehci0                        247          1
irq22: atapci1                        68          0
irq32: mpt0                        2065          9
cpu0: timer                      441265      1987
irq256: bce0                          1          0
irq257: bce1                        120          0
cpu1: timer                      431253      1942
Total                            875038      3941

6th Test

Reset CPU to All Cores in BIOS Settings
Everything Works!

R510 w/ both NICs installed, CPU = ALL

$ dmesg; vmstat -i
Copyright 1992-2010 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 8.1-RELEASE-p2 #0: Sat Feb 26 15:29:09 EST 2011
    sullrich@FreeBSD_8.0_pfSense_2.0-snaps.pfsense.org:/usr/obj.pfSense/usr/pfSensesrc/src/sys/pfSense_SMP.8 i386
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: Intel(R) Xeon(R) CPU          E5503  @ 2.00GHz (2000.08-MHz 686-class CPU)
  Origin = "GenuineIntel"  Id = 0x106a5  Family = 6  Model = 1a  Stepping = 5
  Features=0xbfebfbff <fpu,vme,de,pse,tsc,msr,pae,mce,cx8,apic,sep,mtrr,pge,mca,cmov,pat,pse36,clflush,dts,acpi,mmx,fxsr,sse,sse2,ss,htt,tm,pbe>Features2=0x9ce3bd <sse3,dtes64,mon,ds_cpl,vmx,est,tm2,ssse3,cx16,xtpr,pdcm,dca,sse4.1,sse4.2,popcnt>AMD Features=0x28100000 <nx,rdtscp,lm>AMD Features2=0x1 <lahf>TSC: P-state invariant
real memory  = 2147483648 (2048 MB)
avail memory = 2069499904 (1973 MB)
ACPI APIC Table: <dell  pe_sc3 ="">FreeBSD/SMP: Multiprocessor System Detected: 4 CPUs
FreeBSD/SMP: 2 package(s) x 2 core(s)
cpu0 (BSP): APIC ID: 16
cpu1 (AP): APIC ID: 20
cpu2 (AP): APIC ID:  0
cpu3 (AP): APIC ID:  4
ioapic1: Changing APIC ID to 1
ioapic0 <version 2.0="">irqs 0-23 on motherboard
ioapic1 <version 2.0="">irqs 32-55 on motherboard
wpi: You need to read the LICENSE file in /usr/share/doc/legal/intel_wpi/.
wpi: If you agree with the license, set legal.intel_wpi.license_ack=1 in /boot/loader.conf.
module_register_init: MOD_LOAD (wpi_fw, 0xc095c1e0, 0) error 1
ipw_bss: You need to read the LICENSE file in /usr/share/doc/legal/intel_ipw/.
ipw_bss: If you agree with the license, set legal.intel_ipw.license_ack=1 in /boot/loader.conf.
module_register_init: MOD_LOAD (ipw_bss_fw, 0xc0767240, 0) error 1
ipw_ibss: You need to read the LICENSE file in /usr/share/doc/legal/intel_ipw/.
ipw_ibss: If you agree with the license, set legal.intel_ipw.license_ack=1 in /boot/loader.conf.
module_register_init: MOD_LOAD (ipw_ibss_fw, 0xc0767300, 0) error 1
ipw_monitor: You need to read the LICENSE file in /usr/share/doc/legal/intel_ipw/.
ipw_monitor: If you agree with the license, set legal.intel_ipw.license_ack=1 in /boot/loader.conf.
module_register_init: MOD_LOAD (ipw_monitor_fw, 0xc07673c0, 0) error 1
wlan: mac acl policy registered
kbd1 at kbdmux0
cryptosoft0: <software crypto="">on motherboard
padlock0: No ACE support.
acpi0: <dell pe_sc3="">on motherboard
acpi0: [ITHREAD]
acpi0: Power Button (fixed)
Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x808-0x80b on acpi0
cpu0: <acpi cpu="">on acpi0
cpu1: <acpi cpu="">on acpi0
cpu2: <acpi cpu="">on acpi0
cpu3: <acpi cpu="">on acpi0
acpi_hpet0: <high precision="" event="" timer="">iomem 0xfed00000-0xfed003ff on acpi0
Timecounter "HPET" frequency 14318180 Hz quality 900
pcib0: <acpi host-pci="" bridge="">port 0xcf8-0xcff on acpi0
pci0: <acpi pci="" bus="">on pcib0
pcib1: <acpi pci-pci="" bridge="">at device 1.0 on pci0
pci1: <acpi pci="" bus="">on pcib1
bce0: <broadcom netxtreme="" ii="" bcm5716="" 1000base-t="" (c0)="">mem 0xd6000000-0xd7ffffff irq 36 at device 0.0 on pci1
miibus0: <mii bus="">on bce0
brgphy0: <bcm5709c 10="" 100="" 1000basetx="" phy="">PHY 1 on miibus0
brgphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto
bce0: [ITHREAD]
bce0: ASIC (0x57092008); Rev (C0); Bus (PCIe x4, 2.5Gbps); B/C (5.2.3); Flags (MSI|MFW); MFW (NCSI 2.0.11)
bce1: <broadcom netxtreme="" ii="" bcm5716="" 1000base-t="" (c0)="">mem 0xd8000000-0xd9ffffff irq 48 at device 0.1 on pci1
miibus1: <mii bus="">on bce1
brgphy1: <bcm5709c 10="" 100="" 1000basetx="" phy="">PHY 1 on miibus1
brgphy1:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto
bce1: [ITHREAD]
bce1: ASIC (0x57092008); Rev (C0); Bus (PCIe x4, 2.5Gbps); B/C (5.2.3); Flags (MSI|MFW); MFW (NCSI 2.0.11)
pcib2: <acpi pci-pci="" bridge="">at device 3.0 on pci0
pci2: <acpi pci="" bus="">on pcib2
mpt0: <lsilogic sas="" sata="" adapter="">port 0xfc00-0xfcff mem 0xde2ec000-0xde2effff,0xde2f0000-0xde2fffff irq 32 at device 0.0 on pci2
mpt0: [ITHREAD]
mpt0: MPI Version=1.5.18.0
mpt0: Capabilities: ( RAID-0 RAID-1E RAID-1 )
mpt0: 1 Active Volume (2 Max)
mpt0: 2 Hidden Drive Members (14 Max)
pcib3: <acpi pci-pci="" bridge="">at device 7.0 on pci0
pci3: <acpi pci="" bus="">on pcib3
pcib4: <pci-pci bridge="">at device 0.0 on pci3
pci4: <pci bus="">on pcib4
pcib5: <pci-pci bridge="">at device 2.0 on pci4
pci5: <pci bus="">on pcib5
igb0: <intel(r) 1000="" pro="" network="" connection="" version="" -="" 2.0.7="">port 0xecc0-0xecdf mem 0xdbfc0000-0xdbfdffff,0xdc000000-0xdc3fffff,0xdbfb8000-0xdbfbbfff irq 47 at device 0.0 on pci5
igb0: Using MSIX interrupts with 5 vectors
igb0: [ITHREAD]
igb0: [ITHREAD]
igb0: [ITHREAD]
igb0: [ITHREAD]
igb0: [ITHREAD]
igb1: <intel(r) 1000="" pro="" network="" connection="" version="" -="" 2.0.7="">port 0xece0-0xecff mem 0xdbfe0000-0xdbffffff,0xdc400000-0xdc7fffff,0xdbfbc000-0xdbfbffff irq 46 at device 0.1 on pci5
igb1: Using MSIX interrupts with 5 vectors
igb1: [ITHREAD]
igb1: [ITHREAD]
igb1: [ITHREAD]
igb1: [ITHREAD]
igb1: [ITHREAD]
pcib6: <pci-pci bridge="">at device 4.0 on pci4
pci6: <pci bus="">on pcib6
igb2: <intel(r) 1000="" pro="" network="" connection="" version="" -="" 2.0.7="">port 0xdcc0-0xdcdf mem 0xdb3c0000-0xdb3dffff,0xdb400000-0xdb7fffff,0xdb3b8000-0xdb3bbfff irq 38 at device 0.0 on pci6
igb2: Using MSIX interrupts with 5 vectors
igb2: [ITHREAD]
igb2: [ITHREAD]
igb2: [ITHREAD]
igb2: [ITHREAD]
igb2: [ITHREAD]
igb3: <intel(r) 1000="" pro="" network="" connection="" version="" -="" 2.0.7="">port 0xdce0-0xdcff mem 0xdb3e0000-0xdb3fffff,0xdb800000-0xdbbfffff,0xdb3bc000-0xdb3bffff irq 45 at device 0.1 on pci6
igb3: Using MSIX interrupts with 5 vectors
igb3: [ITHREAD]
igb3: [ITHREAD]
igb3: [ITHREAD]
igb3: [ITHREAD]
igb3: [ITHREAD]
pcib7: <acpi pci-pci="" bridge="">at device 9.0 on pci0
pci7: <acpi pci="" bus="">on pcib7
pcib8: <pci-pci bridge="">at device 0.0 on pci7
pci8: <pci bus="">on pcib8
pcib9: <pci-pci bridge="">at device 2.0 on pci8
pci9: <pci bus="">on pcib9
igb4: <intel(r) 1000="" pro="" network="" connection="" version="" -="" 2.0.7="">port 0xccc0-0xccdf mem 0xdd7c0000-0xdd7dffff,0xdd800000-0xddbfffff,0xdd7b8000-0xdd7bbfff irq 55 at device 0.0 on pci9
igb4: Using MSIX interrupts with 5 vectors
igb4: [ITHREAD]
igb4: [ITHREAD]
igb4: [ITHREAD]
igb4: [ITHREAD]
igb4: [ITHREAD]
igb5: <intel(r) 1000="" pro="" network="" connection="" version="" -="" 2.0.7="">port 0xcce0-0xccff mem 0xdd7e0000-0xdd7fffff,0xddc00000-0xddffffff,0xdd7bc000-0xdd7bffff irq 49 at device 0.1 on pci9
igb5: Using MSIX interrupts with 5 vectors
igb5: [ITHREAD]
igb5: [ITHREAD]
igb5: [ITHREAD]
igb5: [ITHREAD]
igb5: [ITHREAD]
pcib10: <pci-pci bridge="">at device 4.0 on pci8
pci10: <pci bus="">on pcib10
igb6: <intel(r) 1000="" pro="" network="" connection="" version="" -="" 2.0.7="">port 0xbcc0-0xbcdf mem 0xdcbc0000-0xdcbdffff,0xdcc00000-0xdcffffff,0xdcbb8000-0xdcbbbfff irq 40 at device 0.0 on pci10
igb6: Using MSIX interrupts with 5 vectors
igb6: [ITHREAD]
igb6: [ITHREAD]
igb6: [ITHREAD]
igb6: [ITHREAD]
igb6: [ITHREAD]
igb7: <intel(r) 1000="" pro="" network="" connection="" version="" -="" 2.0.7="">port 0xbce0-0xbcff mem 0xdcbe0000-0xdcbfffff,0xdd000000-0xdd3fffff,0xdcbbc000-0xdcbbffff irq 50 at device 0.1 on pci10
igb7: Using MSIX interrupts with 5 vectors
igb7: [ITHREAD]
igb7: [ITHREAD]
igb7: [ITHREAD]
igb7: [ITHREAD]
igb7: [ITHREAD]
pcib11: <acpi pci-pci="" bridge="">at device 10.0 on pci0
pci11: <acpi pci="" bus="">on pcib11
pci0: <base peripheral,="" interrupt="" controller=""> at device 20.0 (no driver attached)
pci0: <base peripheral,="" interrupt="" controller=""> at device 20.1 (no driver attached)
pci0: <base peripheral,="" interrupt="" controller=""> at device 20.2 (no driver attached)
uhci0: <intel 82801ji="" (ich10)="" usb="" controller="" usb-d="">port 0xac40-0xac5f irq 17 at device 26.0 on pci0
uhci0: [ITHREAD]
usbus0: <intel 82801ji="" (ich10)="" usb="" controller="" usb-d="">on uhci0
uhci1: <intel 82801ji="" (ich10)="" usb="" controller="" usb-e="">port 0xac60-0xac7f irq 18 at device 26.1 on pci0
uhci1: [ITHREAD]
usbus1: <intel 82801ji="" (ich10)="" usb="" controller="" usb-e="">on uhci1
ehci0: <intel 82801ji="" (ich10)="" usb="" 2.0="" controller="" usb-b="">mem 0xde0fe000-0xde0fe3ff irq 19 at device 26.7 on pci0
ehci0: [ITHREAD]
usbus2: EHCI version 1.0
usbus2: <intel 82801ji="" (ich10)="" usb="" 2.0="" controller="" usb-b="">on ehci0
uhci2: <intel 82801ji="" (ich10)="" usb="" controller="" usb-a="">port 0xac80-0xac9f irq 21 at device 29.0 on pci0
uhci2: [ITHREAD]
usbus3: <intel 82801ji="" (ich10)="" usb="" controller="" usb-a="">on uhci2
uhci3: <intel 82801ji="" (ich10)="" usb="" controller="" usb-b="">port 0xaca0-0xacbf irq 20 at device 29.1 on pci0
uhci3: [ITHREAD]
usbus4: <intel 82801ji="" (ich10)="" usb="" controller="" usb-b="">on uhci3
uhci4: <intel 82801ji="" (ich10)="" usb="" controller="" usb-c="">port 0xacc0-0xacdf irq 21 at device 29.2 on pci0
uhci4: [ITHREAD]
usbus5: <intel 82801ji="" (ich10)="" usb="" controller="" usb-c="">on uhci4
uhci5: <intel 82801ji="" (ich10)="" usb="" controller="" usb-f="">port 0xace0-0xacff irq 20 at device 29.3 on pci0
uhci5: [ITHREAD]
usbus6: <intel 82801ji="" (ich10)="" usb="" controller="" usb-f="">on uhci5
ehci1: <intel 82801ji="" (ich10)="" usb="" 2.0="" controller="" usb-a="">mem 0xde0ff000-0xde0ff3ff irq 21 at device 29.7 on pci0
ehci1: [ITHREAD]
usbus7: EHCI version 1.0
usbus7: <intel 82801ji="" (ich10)="" usb="" 2.0="" controller="" usb-a="">on ehci1
pcib12: <acpi pci-pci="" bridge="">at device 30.0 on pci0
pci12: <acpi pci="" bus="">on pcib12
vgapci0: <vga-compatible display="">mem 0xd5800000-0xd5ffffff,0xda7fc000-0xda7fffff,0xda800000-0xdaffffff irq 19 at device 3.0 on pci12</vga-compatible></acpi></acpi></intel></intel></intel></intel></intel></intel></intel></intel></intel></intel></intel></intel></intel></intel></intel></intel></acpi></acpi></intel(r)></intel(r)></pci></pci-pci></intel(r)></intel(r)></pci></pci-pci></pci></pci-pci></acpi></acpi></intel(r)></intel(r)></pci></pci-pci></intel(r)></intel(r)></pci></pci-pci></pci></pci-pci></acpi></acpi></lsilogic></acpi></acpi></bcm5709c></mii></broadcom></bcm5709c></mii></broadcom></acpi></acpi></acpi></acpi></high></acpi></acpi></acpi></acpi></dell></software></version></version></dell ></lahf></nx,rdtscp,lm></sse3,dtes64,mon,ds_cpl,vmx,est,tm2,ssse3,cx16,xtpr,pdcm,dca,sse4.1,sse4.2,popcnt></fpu,vme,de,pse,tsc,msr,pae,mce,cx8,apic,sep,mtrr,pge,mca,cmov,pat,pse36,clflush,dts,acpi,mmx,fxsr,sse,sse2,ss,htt,tm,pbe></ep1></dell></vendor></vendor></ata></dell></dp></teac></intel></intel></intel></intel></intel></intel></intel></intel></intel></intel></intel></intel></intel></intel></intel></intel></cpu></enhanced></cpu></enhanced></at></keyboard></generic></system></isa></at></ata></ata></intel></ata></ata></intel></isa></pci-isa></vga-compatible></acpi></acpi></intel></intel></intel></intel></intel></intel></intel></intel></intel></intel></intel></intel></intel></intel></intel></intel></acpi></acpi></intel(r)></intel(r)></pci></pci-pci></intel(r)></intel(r)></pci></pci-pci></pci></pci-pci></acpi></acpi></intel(r)></intel(r)></pci></pci-pci></intel(r)></intel(r)></pci></pci-pci></pci></pci-pci></acpi></acpi></lsilogic></acpi></acpi></bcm5709c></mii></broadcom></bcm5709c></mii></broadcom></acpi></acpi></acpi></acpi></high></acpi></acpi></dell></software></version></version></dell ></lahf></nx,rdtscp,lm></sse3,dtes64,mon,ds_cpl,vmx,est,tm2,ssse3,cx16,xtpr,pdcm,dca,sse4.1,sse4.2,popcnt></fpu,vme,de,pse,tsc,msr,pae,mce,cx8,apic,sep,mtrr,pge,mca,cmov,pat,pse36,clflush,dts,acpi,mmx,fxsr,sse,sse2,ss,htt,tm,pbe></ep1></dell></vendor></vendor></ata></dell></dp></teac></intel></intel></intel></intel></intel></intel></intel></intel></intel></intel></intel></intel></intel></intel></intel></intel></cpu></enhanced></cpu></enhanced></at></keyboard></generic></system></isa></at></ata></ata></intel></ata></ata></intel></isa></pci-isa></vga-compatible></acpi></acpi></intel></intel></intel></intel></intel></intel></intel></intel></intel></intel></intel></intel></intel></intel></intel></intel></acpi></acpi></acpi></acpi></intel(r)></intel(r)></pci></pci-pci></intel(r)></intel(r)></pci></pci-pci></pci></pci-pci></acpi></acpi></lsilogic></acpi></acpi></bcm5709c></mii></broadcom></bcm5709c></mii></broadcom></acpi></acpi></acpi></acpi></high></acpi></acpi></dell></software></version></version></dell ></lahf></nx,rdtscp,lm></sse3,dtes64,mon,ds_cpl,vmx,est,tm2,ssse3,cx16,xtpr,pdcm,dca,sse4.1,sse4.2,popcnt></fpu,vme,de,pse,tsc,msr,pae,mce,cx8,apic,sep,mtrr,pge,mca,cmov,pat,pse36,clflush,dts,acpi,mmx,fxsr,sse,sse2,ss,htt,tm,pbe></ep1></dell></vendor></vendor></ata></dell></dp></teac></intel></intel></intel></intel></intel></intel></intel></intel></intel></intel></intel></intel></intel></intel></intel></intel></cpu></enhanced></cpu></enhanced></cpu></enhanced></cpu></enhanced></at></keyboard></generic></system></isa></at></ata></ata></intel></ata></ata></intel></isa></pci-isa></vga-compatible></acpi></acpi></intel></intel></intel></intel></intel></intel></intel></intel></intel></intel></intel></intel></intel></intel></intel></intel></acpi></acpi></acpi></acpi></intel(r)></intel(r)></pci></pci-pci></intel(r)></intel(r)></pci></pci-pci></pci></pci-pci></acpi></acpi></lsilogic></acpi></acpi></bcm5709c></mii></broadcom></bcm5709c></mii></broadcom></acpi></acpi></acpi></acpi></high></acpi></acpi></acpi></acpi></dell></software></version></version></dell ></lahf></nx,rdtscp,lm></sse3,dtes64,mon,ds_cpl,vmx,est,tm2,ssse3,cx16,xtpr,pdcm,dca,sse4.1,sse4.2,popcnt></fpu,vme,de,pse,tsc,msr,pae,mce,cx8,apic,sep,mtrr,pge,mca,cmov,pat,pse36,clflush,dts,acpi,mmx,fxsr,sse,sse2,ss,htt,tm,pbe></enter>

[the.it.dude]

So in summary…

It appears I can get the system up and running (without crippling the physical system) by installing 1st without any of the add-in nics installed.  However, this whole process has left me with an uneasy feeling to move forward into production with these systems.  Doesn't it stand to reason that if the install had such troubles than I may run into issues once the system is in production and under load?

Thanks,

Jeff

[wallabybob]

I can't offer an explanation for the difficulty you have had with the initial installs.

Maybe it would be worthwhile cloning the hard drive and putting the original away as a backup to help you get running again quickly if you have hard drive problems.

I expect there would be lots of pfSense users who rarely do an install; they do a firmware upgrade instead. I wouldn't be at all surprised if the install process is much less exercised than the "production" software.

[the.it.dude]

wallabybob,

Thanks for the suggestion.  These systems both have a Hardware RAID-1 setup.  I wanted the redundancy.  Makes pulling hard drives a more difficult and expensive process.  But, maybe it is worthwhile seeing if I can disable the RAID and see what happens during the install?

Jeff

[the.it.dude]

Disabling the RAID made no difference.

Also, I was too optimistic with my analysis.  Even though the system came up fine after installing the NIC cards, as soon as I started configuring it via the web interface, things got wacky.  After each change I would lose access to the web interface.  I could still ping the firewall and the console was still OK.  But, even restarting the webconfigurator from the console would not bring access to the web gui back.  I had to fully reboot the server.

I think I'll start up a new thread that references this thread.  Since this one is getting long winded, I want to post a summary of my issues and what my options are moving forward.