I can ping PFSense but PFSense can't ping back
-
Well pfsense put it on the wire to the correct mac.. So the problem has nothing to do with pfsense.
Wrong network masks on the client? What is between pfsense and the client? Switch I assume - any vlans setup on the switch, is the switch dumb?
-
@striker-0 said in I can ping PFSense but PFSense can't ping back:
00:11:09:d7:2b:fa
Hey
Try so
System/Advanced/Networking
-
The client is assigned its IP through a static DHCP mapping from pfsense so I don't think it is a wrong network mask. Additionally, pfsense cannot ping any LAN client, i'm just focusing on this one as this is the one I care about pfsense being able to port forward to.
There are two dumb switches between pfsense and the client in question. They have both been rebooted several times to clear anything they might be retaining internally.
There are no vlans setup in my environment.
-
@striker-0
try check " Disable hardware checksum offloading" in System/Advanced/Networking -
@konstanti I gave that a try, Thank You for the suggest! Rebooted pfsense to ensure it was applied. Same results on a ping test.
-
@striker-0
Show the output of the command
ifconfig -m
and arp -a -
@konstanti The forums are being weird and telling me that the content is flagged as spam. I've attached the requested results as a text file.0_1548526770045_Results.txt
-
@striker-0
So in a whole, all looks decently
What you can try- Change the LAN - re0 interface speed (e.g. media 100baseTX mediaopt full-duplex)
- Check the lan re0 - switch cable
- Connect any device directly to PFSense and try to ping .
- check the subnet mask in dhcp server settings and devices that have permanent ip addresses (255.255.255.0)
-
Client firewalls? If you changed anything such as your LAN subnet your desktops will change to "public" and block everything.
Even changing an interface on your router could trigger that.
https://www.netgate.com/docs/pfsense/nat/port-forward-troubleshooting.html
As you eluded to in your first post- once you figure out why your port forward does not work you will most likely also fix the ping.
-
If you can ping one way and not the other it is almost certainly a firewall on the device you cannot ping blocking it. One way ping success proves two-way traffic, routing (for the most part in most cases), and layer 2 are correct.
-
-
I would prefer not to change my link speed. It is currently running at 1000. If I switch it down to 10 or 100, I would be limiting my access to my internet as my internet connection is currently rated for 300. Additionally, this was working previously under the current link state, so I would be surprised if this would resolve anything. What is your rationale for checking this?
-
Tried a different cable, no change in results.
-
Tried connecting a device directly to pfsense. No change in results.
-
Subnet Mask is set to 255.255.255.0 in DHCP and aligns with the client.
-
-
@chpalmer I thought it could be client side firewall too. I normally leave those disabled on my internal LAN as they just cause unnecessary trouble. I have confirmed and they are still off.
-
Then you'll have to packet capture to see the pings going out and nothing coming back, look at the MAC addresses, etc.
-
@striker-0
Reducing the connection speed is just a test
I am very confused by the line in ping test
255.255.255.0 > 10.0.100.51: ICMP echo request, id 16367, seq 0, length 64
( I don't know what's the subnet mask )Should be so
length 98: 192.168.1.1 > 192.168.1.230: ICMP echo request, id 30542, seq 0, length 64
length 98: 192.168.1.230 > 192.168.1.1: ICMP echo reply, id 30542, seq 0, length 64
length 98: 192.168.1.1 > 192.168.1.230: ICMP echo request, id 30542, seq 1, length 64
length 98: 192.168.1.230 > 192.168.1.1: ICMP echo reply, id 30542, seq 1, length 64Can you put the packet capture file here ?
-
@derelict I have confirmed the firewall is off. This issue occurs across all devices on my network, the only constant is pfsense. Additionally, within my network other devices can ping each other and I can connect to the port I am trying to forward. Something is going on with pfsense or the hardware it resides on.
-
@striker-0
And another question - how much do you have active NORDVPN tunnels ?
if you turn them off, will anything change ? -
@striker-0 said in I can ping PFSense but PFSense can't ping back:
255.255.255.0 > 10.0.100.51:
That is NOT right it sould be pinging from pfsense IP on that 10.0.100 network..
re0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500 options=82098<VLAN_MTU,VLAN_HWTAGGING,VLAN_HWCSUM,WOL_MAGIC,LINKSTATE> capabilities=18399b<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,VLAN_HWCSUM,TSO4,WOL_UCAST,WOL_MCAST,WOL_MAGIC,LINKSTATE,NETMAP> ether 00:11:09:d7:2b:fa hwaddr 00:11:09:d7:2b:fa inet6 fe80::211:9ff:fed7:2bfa%re0 prefixlen 64 scopeid 0x2 inet 10.0.100.1 netmask 0xffffff00 broadcast 10.0.100.255 nd6 options=21<PERFORMNUD,AUTO_LINKLOCAL> media: Ethernet autoselect (1000baseT <full-duplex,master>) status: activeThat is the IP it should be pinging from 10.0.100.1
-
@striker-0 Post a packet capture taken on each interface of pings that work and pings that fail.
-
@konstanti at the moment, my NORDVPN tunnel is down. I see no difference in activity when the tunnel is up or down.
-
@johnpoz
All this is very strange, because of the webgui
pfsense is also forming a command
/ sbin/ping -S 10.0.100.1 -c 3 10.0.100.51 (as seen in the picture)
and tcpdump shows another
