segment wifi traffic (guest, IoT, trusted)

JKnott

Yes, I used to do that here. The unmanaged switch will pass the VLAN tagged frames, so that the AP can sort things out. Wired devices that can't be configured to work directly with VLANs will still work on the native LAN and will ignore the tagged frames. Computers can be configured to work directly with VLANs.

johnpoz

While you can do that.. Understand that dumb switch doesn't understand vlans.. So there is no isolation. All the broadcast and multicast traffic from all the vlans as soon as hits switch will go to all the other ports.

While your dumb switch will pass the vlan tags.. Since he doesn't understand them doesn't know that broadcast/multicast traffic from vlan X, is not suppose to go to all the ports.

If your doing it that way because you can not afford say $30-50 switch... You shouldn't be running so many freaking devices in the first place. I mean the electric cost alone must eat up your whole budget ;)

Give up couple $10 coffee's at starbucks and get a switch that actually understands vlans.

JKnott

@johnpoz said in segment wifi traffic (guest, IoT, trusted):

So there is no isolation. All the broadcast and multicast traffic from all the vlans as soon as hits switch will go to all the other ports.

There is some isolation in that the devices won't receive the packets for other VLANs. They will appear at the NIC, where they will be promptly ignored.

farmerjohn

@johnpoz

So there is no isolation. All the broadcast and multicast traffic from all the vlans as soon as hits switch will go to all the other ports.

seems not optimal, but what is the downside to this? will this cause a noticeable hit to network performance or other issues?

johnpoz

The downside is your sending broadcast/multicast to somewhere it doesn't need to go.

While the nic might drop it. You also can join any vlan you want with any device just be tagging. So no security at all.

If your to the point you wanting to segment your network into different vlans, yet not willing to spend the few bucks required to do it correctly - your doing it F'ing Wrong! ;)

If its a stop gap until your smart switch gets delivered, or you want to do it on purpose as say a easy tap into viewing traffic.. Or your using the dumb switch as sort of relay to extend length of a run or something.. Sure ok..

While there may be some scenarios you need/want to do it - overall its a borked way to do it.

There is one correct answer to want to run vlans on a switch - the switch should understand the tags ;) It doesn't need to be some super managed everything under the sun sort of networking magic that can be done sort of switch.. But it should at least understand what the tag is, and how to process them and isolate them correctly.. So that you actually get the L2 isolation that vlans are meant to do..

JKnott

@farmerjohn

It will waste some bandwidth on the wire, but devices will not recognize packets on a VLAN they're not configured for. Those packets will be discarded by the NIC.

JKnott

@johnpoz said in segment wifi traffic (guest, IoT, trusted):

You also can join any vlan you want with any device just be tagging. So no security at all.

Assuming:

a) You have admin rights¹ and
b) Know how to do that

Yeah, I know many people run their computers as admin because they don't know better and that's the way it came.

bingo600

@farmerjohn
I totally agree w. @johnpoz here.
Get a cheap managed switch for the job.
As a "bonus" you could use the 6 other ports for other vlans, and treat it as an additional 6 Lan interfaces.

@jknott
Just because you could ... Doesn't mean you should.
And certainly not for saving $50

/Bingo

bingo600

@farmerjohn

I suppose you're thinking about dd-wrt

Hw-Rev A1
https://wiki.dd-wrt.com/wiki/index.php/Asus_RT-AC66U

Hw-Rev B1
https://wiki.dd-wrt.com/wiki/index.php/Asus_RT-AC66U_B1

bingo600

There might be some "Trickery" in connecting the managed switch to the Lan IF , and enable tagging , wo. loosing Lan (that you need for configuring).

I suppose you could keep Lan as untagged.

Maybe one of the others have trued to run untagged & tagged on a pfS IF.
I haven't yet

/Bingo

johnpoz

@bingo600 said in segment wifi traffic (guest, IoT, trusted):

Maybe one of the others have trued to run untagged & tagged on a pfS IF.

I run one of my interfaces with native (untagged) and then vlans on it.. There really isn't anything tricky about ;)

You can see that native network my wlan is untagged and on the igb2 interface. While then 2 other networks (vlans) are on that physical interface igb2

JKnott

@bingo600 said in segment wifi traffic (guest, IoT, trusted):

Maybe one of the others have trued to run untagged & tagged on a pfS IF.
I haven't yet

That's what I have here. My guest Wifi is connected via VLAN3 and the main Wifi is on the native LAN. This is quite common with things like VoIP phones and office computers. On the pfsense end, once the VLANs are enabled, there's no difference with a native LAN when configuring them.

farmerjohn

@bingo600

I suppose you're thinking about dd-wrt

That was my original plan, but also considering a Ubiquity UAP-AC-PRO - not sure if flashing and configuring the Asus router will be as simple as buying a Ubiquity.

bingo600

@farmerjohn

I like the UAP AC Pro
I have 5 sites with that model installed.

Then i also assume that $50 for a Vlan switch isn't an issue.

/Bingo

farmerjohn

@johnpoz

There is one correct answer to want to run vlans on a switch - the switch should understand the tags ;)

I currently have 3 unmanged switches in the house
one: trendnet TEG-S80G
two: HP procurve 1410-8G

I'll be attaching the VLAN capable AP into one of the HP procurve switches - until I save up for a managed switch ;)

Are there advantages of replacing the other two dumb switches if I don't intend to run VLAN tagged traffic through them?

if so, I may go with a 3-pack of these Ubiquiti USW-Flex-Mini for $28 each.

bingo600

@farmerjohn
I'd go for 8-port switches ...
Not that 5 wouldn't do , just that w. a 5 , you only have 4(3) for user ports , as the other 1(2) would be used for uplink(s)

The advantage of Vlan enabled switches around your house.
Would be that you could , "pull out" ie. a Guest or "IOT" ethernet port on any switch , if needed. Or you could attach a new "AP AC Pro" on "that" remote switch , if you need better coverage in that area.

I'd only buy managed switches today, price diff is too small not to.

You could reuse your old "dumb" switches , if you have the need for many ports of the same type (vlan) - Just make one port on the managed switch a member of vlan xx , and connect the "dumb" switch to that port.
Now every port on the dumb switch will be a member of vlan xx.

/Bingo

farmerjohn

@bingo600

You could reuse your old "dumb" switches , if you have the need for many ports of the same type (vlan)

Good to know - I'll probably go with 3 of the 5-port flex mini's and if I need to add more devices (same vlan), I'll attach one of my 8-port dumb switches.

But, found this in the unifi datasheet:

USW-Flex-Mini uses port-based VLANs only and does
not support SSH, STP (forwarding only), 802.1X, DNS
suffix, or experience in the controller.

SSH is not an issue for me, but not sure about the other limitations.

bingo600

@farmerjohn

Re : Ubi switches ...
While cheap .. I'd drop them , looks like an el-cheapo model.

D-Link just released a new 1100-08V2 (V2 is new)
https://us.dlink.com/en/products/dgs-1100-08v2-8-port-gigabit-smart-managed-switch

DS
https://us.dlink.com/-/media/obu-content/us/datasheets/dgs/dgs-1100-v2-series_datasheet_v_100_dus.pdf

Guide
https://support.dlink.com/resource/PRODUCTS/DGS-1100-08V2/REVA/DGS-1100-08V2_REVA_MANUAL_v1.00_WW.pdf

Buy
https://www.amazon.com/dp/B08P2C2GXF

I have used the old 1100-08 and 1100-08P (Non V2) , and that is my goto switch when needing something small & effective.

Seems like the PoE V2 has a bit of issues , but $35 for an 8-port & $30 for a 5-port, not that bad.

But they mention some GUI issues
But I'd get one , and try it out , if it were me.

Datasheet actually shows a lot of value for the $$

My choice would be D-Link or Netgear

/Bingo

farmerjohn

@bingo600
thanks for the recommendations - I will check them out. One appeal of the ubiquity, was that if I went with the wireless AP and switches, it would be easier to manage them all under their unifi controller software. I was hoping the reduced features of the flex mini would not be an issue for my use case.

bingo600

@farmerjohn

If you read what you wrote above about the UBI switches

USW-Flex-Mini uses port-based VLANs only and does
not support SSH, STP (forwarding only), 802.1X, DNS
suffix, or experience in the controller.

I read that as it's too cheap to play w. the controller.
So no advantage in going for those cheapo's