SG-5100 takes over 20 minutes to boot after eMMC failure
-
I would expect them to be identical.
-
The ssd should be here in a couple of days.. If I get ambitious, maybe move to it sooner.. But prob just wait til 24.03 comes out - which hopefully will be on schedule and not that far away ;)
-
-
@stephenw10 hahaha - yeah maybe I should knock on some wood when I put that out into the universe, hahahah
-
@johnpoz Have you opened up your 4680 yet ?
The reseller in the UK opened up mine to put in the drive, when I opened it up to pop in a wireless card, one of the screws spins round in the case as its steel screw mating to an aluminium thread.
Bit of a design fault IMO.
-
Hmm, not seen that myself. But those are small screws in to Alu as you say. Easy to over-torque if you're not careful or using the wrong tool.
-
@NogBadTheBad Nope never even thought about opening it ;)
But this emmc failures got me thinking can't hurt to move to ssd, I don't currently have any plans of updating my 4860.. But for a few bucks and extra few minutes during what is normal down time anyway - if that "could maybe" give me a couple extra years before I have to pull the trigger on something new.. Well worth it I say.
I am still on the look out for my unicorn switch, since my sg300 is getting a bit long in the tooth as well.
Something that is multigig, like 24 some ports, fanless - very low power consumption, but also have a few poe ports to get rid of my injectors for my APs... For like couple hundred I would be all over it.. But seems like I am hunting unicorns with those wish list items - heheh
-
Yeah let me know if you find that switch.
-
@stephenw10 yeah... I think asking a bit much, especially at that price point, but I prob pull the trigger even that 400 something mark if it had all those features..
A few combo ports where I could put in sfp+ would be nice too since I am dreaming ;)
-
@johnpoz said in SG-5100 takes over 20 minutes to boot after eMMC failure:
@stephenw10 yeah... I think asking a bit much, especially at that price point, but I prob pull the trigger even that 400 something mark if it had all those features..
A few combo ports where I could put in sfp+ would be nice too since I am dreaming ;)
If you're already invested in the UniFi ecosystem, their switches are great. I got one of these switches awhile back and it rocks!
https://store.ui.com/us/en/collections/unifi-switching-standard-power-over-ethernet/products/usw-24-poe
-
@azdeltawye said in SG-5100 takes over 20 minutes to boot after eMMC failure:
heir switches are great.
That wouldn't be my opinion to be honest.. I have had no issues with their APs.. But their switches not so much..
Do they have such a unicorn switch - I keep up with their product line.. And everyone of their switches feature sets and operation has been underwhelming to be honest.. And a high price point..
-
@stephenw10 said in SG-5100 takes over 20 minutes to boot after eMMC failure:
Yeah let me know if you find that switch.
And me.
-
johnpoz is going for a Transcend TS128GMSA230S. I bought two Transcend TS240GMTS420S they seem to work fine, but for my others SG-5100 I wanted to choose the TS128GMTS430S (ECC enabled I belive) is there a "better" choice when choosing a SSD for the SG-5100?
-
@ms166 said in SG-5100 takes over 20 minutes to boot after eMMC failure:
TS128GMTS430S
That should work fine. I'm not sure how you might define 'better'. You could probably find an SLC drive with better write endurance etc. But it would be waaay more expensive!
-
After reading through this thread, my question is about a recommendation for an SSD for the new 4200. Also, I'm assuming that the mmc-utils mentioned https://docs.netgate.com/pfsense/en/latest/troubleshooting/disk-lifetime.html#emmc will work on the 4200?
--Larry
-
Hello!
I have been using the Transcend MLC drives (MSA370, MTS400S) in builds. Their endurance specs (DWPD, TBW) seem to be much better than the 3D NAND drives.
John
-
It does not, at least currently, because it's also USB connected in the 4200.
-
Thanks @serbus and @stephenw10
Perhaps I should have started a new thread specific to the 4200... But since I didn't: looking for some guidance on the particulars to look for for an SSD for the 4200. The online documentation I've found thus far is thin. Netgate's 4200 web specs say "1x M.2 (M-key slot) x4 PCIe 4.0", Silicom's specs say "NVMe M.2 SSD"
Which form factor (for example, 2242 or 2280??) for the 4200?
Which interface is better for the 4200? I note that the Transcend devices mentioned are SATA III, but the thread is about the SG-5100.
Which version of NVMe?Thoughts & opinions about different types of NAND are certainly welcome, but as I'm not well versed in these issues, pardon what may seem like basic questions.
I have a pair of 4200s on order and would like to get the correct SSDs so that I can install them once they arrive.
https://shop.netgate.com/products/4200-pfsense
https://www.silicom-usa.com/pr/4g-5g-products/4g-5g-appliances/valencia-network-appliance-series/--Larry
-
They are 2280 without any sort of adapter hardware. There is one M-keyed slot and one B-keyed slot. Dual keyed drives will therefore give you most flexibility.
-
Thank you @stephenw10, what about the interface specs (SATA III, PCIe, NVMe) or is this something that doesn't really matter given the 4200 hardware throughput capabilities and application? So for example, the Transcend SATA III M.2 SSDs vs. their PCIe M.2 SSDs?
--Larry