Subcategories

• Cache/Proxy

  Discussions about packages which handle caching and proxy functions such as squid, lightsquid, squidGuard, etc.
  4k Topics

  21k Posts

  J

  @qupfer What did I bang my head over this strange 502 issue. Your solution did it! Thank you so much, even 2.5 years later!
• IDS/IPS

  Discussions about packages whose functions are Intrusion Detection and Intrusion Prevention such as snort, suricata, etc.
  2k Topics

  16k Posts

  B

  @NRgia said in Suricata on Pfsense: @bmeeks Thank you for what you did for Snort or Suricata. I'm not sure what you want me to do on Redmine, due to is a bug tracker. My question is for Product Management, which I will ask it here to be public: What is the plan for these 2 packages, Suricata and Snort? Thank you Yes, Redmine is for both bug reports and feature requests. Asking for the Suricata binary to be updated to the latest 7.0.11 version from upstream is a legitimate Redmine request. I would suggest simply asking for the binary version update instead of asking about future Netgate strategy (such as the support plans for the packages). Strategy discussions typically don't get very far because they deal with proprietary information or plans that a company may not want to publicly discuss. Redmine is where the Netgate developer team tracks all the code changes they make for pfSense. They will see Redmine reports much quicker than a forum post.
• Traffic Monitoring

  Discussions about packages that handle bandwidth and network traffic monitoring functions such as bandwidtd, ntopng, etc.
  571 Topics

  3k Posts

  D

  @Leon-Straathof Data retention settings are handled inside of ntopng. Documentation here. Pay attention to the RRD note. Also, if you've turned on some of the slice and dice time series information (is off by default), I'd suggest turning them back off. These balloon the storage requirements and are of little actual use.
• pfBlockerNG

  Discussions about the pfBlockerNG package
  3k Topics

  20k Posts

  F

  @tinfoilmatt said in Failed or invalid Mime Type: [application/SIMH-tape-data|0]: (ASN data is IPinfo, not Maxmind) Thats correct but "GeoLite2-Country" is from Maxmind ... (that confused me) I'm considering simply adding "application/SIMH-tape-data" to the list to test. Thats what i tought too ... I'll try when I have the time for it ... Edit: I can confirm - adding "application/SIMH-tape-data" to the list at line 257 in /usr/local/pkg/pfblockerng/pfblockerng.inc did the trick - no more error! Edit: OK, problem resolved but I would like to know, whats the cause for that error! (SIMH-tape-data sounds like a "blast from the past" ...) Thanks a lot!
• UPS Tools

  Discussions about Network UPS Tools and APCUPSD packages for pfSense
  101 Topics

  2k Posts

  D

  @jhg said in NUT fails to start after 2.7.2 -> 2.8.0 upgrade: Interesting. I would have thought the initial reboot, which occurred as part of the upgrade, would have done the trick, but it took a second reboot, just now, to get things working. Glad you have it sorted. There was no difference in the output of usbconfig show_ifdrv at any point -- before or after unplugging/replugging the USB cable, nor after rebooting. ... Question: What would tell me whether or not a driver was loaded? If there were an attached driver, it should have shown up with the show_ifdrv command. If you use the command and look at the other usb devices, I think they will show attached drivers. I don't expect to see a driver attached to the ups, because there is a quirk that tells the OS to ignore that device (and not attach a driver). Look for idVendor and idProduct in the above output. The Vendor ID for your device is 0764, which corresponds to Cyber Power Systems, and the Product ID for your device is 0601, which is registered as "PR1500LCDRT2U UPS" (don't sweat an exact match for the name). You can see the quirk with the following command: [25.07-RC][root@fw]/root: usbconfig dump_device_quirks | grep 0764 VID=0x0764 PID=0x0005 REVLO=0x0000 REVHI=0xffff QUIRK=UQ_HID_IGNORE VID=0x0764 PID=0x0501 REVLO=0x0000 REVHI=0xffff QUIRK=UQ_HID_IGNORE VID=0x0764 PID=0x0601 REVLO=0x0000 REVHI=0xffff QUIRK=UQ_HID_IGNORE [25.07-RC][root@fw]/root: Your device is third on the list. The HID_IGNORE quirk says to ignore the device and not attach a driver. @jhg said in NUT fails to start after 2.7.2 -> 2.8.0 upgrade: You might consider adding this resolution to the release notes for 2.8. LOL... sorry, I don't have input to the release notes (I don't work here). While I wrote and maintain various packages, including NUT, I'm still just a volunteer. Most packages are actually written by volunteers.
• ACME

  Discussions about the ACME / Let’s Encrypt package for pfSense
  496 Topics

  3k Posts

  R

  Nice to read that news! Will it be also available for 25.07.1? I got an ! Exclamation Mark, after upgrading to 25.07.1 and reinstalled ACME and it was downgraded to 0.9.
• FRR

  Discussions about the FRR Dynamic Routing package on pfSense
  294 Topics

  1k Posts

  Y

  said in Please update frr on Pfsense+ to FRR 10.3: https://redmine.pfsense.org/issues/15785 now frr 10.4.1
• Tailscale

  Discussions about the Tailscale package
  90 Topics

  598 Posts

  E

  Updated CE 2.7.2 to 1.86.4 Changelog pkg add -f https://pkg.freebsd.org/FreeBSD:14:amd64/latest/All/tailscale-1.86.4.pkg Freshports
• WireGuard

  Discussions about WireGuard
  694 Topics

  4k Posts

  H

  I have Wireguard installed on my firewalls. I have about 12 firewalls and most of them connect back to the main firewall which allows the connection to the servers in the main building. I setup a tunnel on each and then added each location as a peer on the Main firewall. This seemed to work except that the gateway. unde3r Monitor IP it only allows one IP address. So the first one works and shows connected fine, but the other 2 are red and do not connect. Everything seems to work until I added a 3rd peer and then the 1st peer showed as if it was offline even though it looked fine and I was able to connect to devices on that network. Am I supposed to add multiple gateways to the Main firewall so that shows as up? Is this the right way for the tunnels between the buildings which need access will work - By adding a tunnel at that location and just adding a peer to the main location?