Subcategories

• Cache/Proxy

  Discussions about packages which handle caching and proxy functions such as squid, lightsquid, squidGuard, etc.
  4k Topics

  21k Posts

  E

  I even tried deleting and creating a new certificate. Any suggestions?
• IDS/IPS

  Discussions about packages whose functions are Intrusion Detection and Intrusion Prevention such as snort, suricata, etc.
  2k Topics

  16k Posts

  S

  @icoso said in Snort Alert list explanation: If I only run it on the LAN ports wouldn't that only prevent my users from going outbound to certain IP's? I think you're misunderstanding how it works. In legacy mode it will check for "bad" packets going past the router, and add the "bad" IP to a table/alias, and the firewall will block packets to/from that table. It is not directional in the sense of "it's on LAN so only watches outbound." Running it on LAN also identifies which internal device triggered the rule because otherwise on WAN it is after NAT, since it's outside the firewall. You can run it on WAN, sure. Some do if they have a lot of internal interfaces and don't want that many Snort/Suricata processes running. It's a tradeoff of "scanning packets that will never actually arrive" vs convenience/RAM usage. Here is the setting I mentioned in Suricata; the packages are similar to maybe Snort has it also: [image: 1757427238489-8223c7ca-ba6c-4503-8668-2b7c03e597ef-image.png] However, on the Snort interface settings click the View List button by "IP Pass List" and you'll see which IPs are ignored by default.
• Traffic Monitoring

  Discussions about packages that handle bandwidth and network traffic monitoring functions such as bandwidtd, ntopng, etc.
  572 Topics

  3k Posts

  K

  @Antibiotic No it’s not possible with NtopNG as it is not a Netflow collector. You need nProbe for that which will “translate” recieved netflows into flows that NtopNG understands and can visualize (with very very little detail might I add as Netflows has no additonal information apart from sender/reciever and volume). The NtopNG package and the product in general is more geared towards visualising and recording traffic details from actual packet captures. This contains MUCH more metadata about the sessions than netflows (DNS names, protocol information and myriads of other things). But pffSense Plus has a builtin Netflow exporter if you have an external netflow collector on hand.
• pfBlockerNG

  Discussions about the pfBlockerNG package
  3k Topics

  20k Posts

  T

  @BiloxiGeek said in DNSBL and IPv6: Does it just follow the IPv4 address that is listed above that? In my case it would end up being ::10.0.0.86 Yes. In this specific context that's the notation being used. (Full IPv6 web server address, for reference then, would be: http://[0000:0000:0000:0000:0010:0000:0000:0086]) Nota bene: I use 0.0.0.0 which renders the DNSBL webserver useless and inaccessible, but otherwise returns 0.0.0.0 or ::/NOERROR answers to all blocked lookups.
• UPS Tools

  Discussions about Network UPS Tools and APCUPSD packages for pfSense
  101 Topics

  2k Posts

  D

  @jhg said in NUT fails to start after 2.7.2 -> 2.8.0 upgrade: Interesting. I would have thought the initial reboot, which occurred as part of the upgrade, would have done the trick, but it took a second reboot, just now, to get things working. Glad you have it sorted. There was no difference in the output of usbconfig show_ifdrv at any point -- before or after unplugging/replugging the USB cable, nor after rebooting. ... Question: What would tell me whether or not a driver was loaded? If there were an attached driver, it should have shown up with the show_ifdrv command. If you use the command and look at the other usb devices, I think they will show attached drivers. I don't expect to see a driver attached to the ups, because there is a quirk that tells the OS to ignore that device (and not attach a driver). Look for idVendor and idProduct in the above output. The Vendor ID for your device is 0764, which corresponds to Cyber Power Systems, and the Product ID for your device is 0601, which is registered as "PR1500LCDRT2U UPS" (don't sweat an exact match for the name). You can see the quirk with the following command: [25.07-RC][root@fw]/root: usbconfig dump_device_quirks | grep 0764 VID=0x0764 PID=0x0005 REVLO=0x0000 REVHI=0xffff QUIRK=UQ_HID_IGNORE VID=0x0764 PID=0x0501 REVLO=0x0000 REVHI=0xffff QUIRK=UQ_HID_IGNORE VID=0x0764 PID=0x0601 REVLO=0x0000 REVHI=0xffff QUIRK=UQ_HID_IGNORE [25.07-RC][root@fw]/root: Your device is third on the list. The HID_IGNORE quirk says to ignore the device and not attach a driver. @jhg said in NUT fails to start after 2.7.2 -> 2.8.0 upgrade: You might consider adding this resolution to the release notes for 2.8. LOL... sorry, I don't have input to the release notes (I don't work here). While I wrote and maintain various packages, including NUT, I'm still just a volunteer. Most packages are actually written by volunteers.
• ACME

  Discussions about the ACME / Let’s Encrypt package for pfSense
  501 Topics

  3k Posts

  A

  Hi, Please help to forward / report the bugs in ACME 1.0 package. Thanks.
• FRR

  Discussions about the FRR Dynamic Routing package on pfSense
  294 Topics

  1k Posts

  Y

  said in Please update frr on Pfsense+ to FRR 10.3: https://redmine.pfsense.org/issues/15785 now frr 10.4.1
• Tailscale

  Discussions about the Tailscale package
  90 Topics

  610 Posts

  E

  Updated CE 2.7.2 to 1.86.4_1 Changelog pkg add -f https://pkg.freebsd.org/FreeBSD:14:amd64/latest/All/tailscale-1.86.4_1.pkg Freshports
• WireGuard

  Discussions about WireGuard
  700 Topics

  4k Posts

  B

  @HFADmin said in Wireguard Multi VPN Tunnels: Can I have the main pfsense monitor all the gateways That is the default.