The systemspecs should be ok, however you are running an unsupported configuration atm.

You could switch LAN or OPT1 to be the wireless/olsr interface; or, enable the olsr dynamic gateway extension and it will overwrite your default route in the route table.

olsr + dhcp to non-olsr wireless clients (pseudo-AP), combined all on one wireless card…
http://forum.pfsense.org/index.php/topic,2353.0.html

@KiFFuSeR:

I have 3 pfsense machines working with that card as Wan interface doing wireless client type router in a community based setup.

¨
You are right… i tried other box and this card and everything works fine !
Thanks

Wait for 1.2 which will be based on FreeBSD 6.2.  No time table as we are not in control of releasing FreeBSD 6.2.

Got it to work at last…

Reasons for the trouble were two things.

1. The documentation says theres no filtering between bridged interfaces. But I have to set a rule on the OPT1 interface to allow all traffic to all nets like this to make it work (especially for DHCP request).

Proto Source Port    Destination    Port    Gateway    Description  *    *      *      *           *      *          OPT1 -> Any

So there IS filtering between bridged interfaces.

2. Flaky Wlan driver on the client side. Nasty Netgear WG511 PCMCIA Card. Forced it to eat a newer driver for an 3Com Office Connect Card and works now without problems and even has AES support now.

So for all people with the same problem:

If you want to create the following setup:
WAN -> Internet
LAN -> Local wired network
OPT1 -> AP Wireless LAN bridged to Local wired Network
just do the following

-Get your WAN and LAN running. Then go to the OPT1 settings page and set it to be bridged with LAN. Leave the IP configuration for the OPT1 interface to static.

-Setup the remaining wifi stuff (WPA,WEP,Keys etc) and save the settings.

-Next go to the Firewall Rules settings page and click on OPT1 interface. Add a new rule to allow traffic from any to any.

This did the trick for me.

Just in case anyone else is interested the Lucent Hermes chipset cards do not support AP mode in BSD.

http://www.freebsd.org/cgi/man.cgi?query=wi&sektion=4&manpath=FreeBSD+6.1-RELEASE

bummer as that is all I have for cards :)

Interestingly enough my Orinoco BG2000 AP uses this exact same card and works just fine as an AP.

Maybe your card doesn't support WPA2 under freebsd. We don't detect the capabilities of the card concerning wpa2 afaik. You'll find a config script (generated from your gui settings) for the wireless card in your /tmp folder. Try to ssh in to your system and run the script manually. Does it reject some of the options that the script tries to set?

@jeroen234:

if iam lucky i will have sunday 2 senao 11mb wireless cards that use wi0 driver
and 1 atheros card for my soekris box then i will do some tests
i will have then :
wan,lan,opt1,opt2,opt3

sounds great! please let me your test results known

best regards

stop using rc3 its stoneage pfsense
use 1.01 pfsense insted

you need 2x 750 mha for the cards that is 1,5 ah
and 1,5 ah for the wrap
so you need a adapter with at least 3 ah

In what mode does that nic run? In accesspoint mode it should show always link up. In case it's one of the client modes like infrastructure or adhoc it means the accesspoint it was connected went down.

What are the next best few non-atheros mini-pci wireless cards?

Check status>systemlogs for obvious messages. If you can't access your system anymore after this bug occurs setup a remote syslog server to send the messages to another system to investigate later.

If this is a wrap or a soekris make sure your PSU is strong enough to handle the 2 wireless cards. If it is a wrap make sure you have the latest bios. There were some fixes that affect atheros problems.

@hoba:

If you want to unhide it from the gui just remove the two highlighted green lines from the file ( http://cvstrac.pfsense.com/chngview?cn=14890 ) by using diagnostics>edit but it won't work. That's why it was hidden. It's not a pfSense bug but a driver bug in freebsd.

Thanks a lot !! I unhided the setting and enabled it and as far as i can tell it works for me.

The fix already is in the codetree, no need for further information on the situation. This bug does not always appear, so you only need to reboot if the rules are not applied.

Never heard of issues like that yet. Maybe your ISP is a bit "special".

I'm not surprised as my only problems thus far have been with a USB keyboard :) Unfortunately I can only use half height cards in this case, and I haven't found any dual ports that would fit. If that kind of error simply kills the wireless, I can live with it being a little flakey since it's just for Internet connectivity in conference rooms. As long as it doesn't kill the firewall completely.

Which CPEs do you recommend for this? I know Tranzeo is one but are their any others just as good and cheaper?