@johnpoz: Yeah you can see for sure that IP is part of the ntp pool. http://www.pool.ntp.org/scores/95.211.224.12 Yeah…that's my biggest gripe with a lot of the blacklist type of IP lists.  They mix up the good guys and the bad guys sometimes, and it is frequently difficult to get mistakes fixed. Bill

@pronten2: Ok i will try i will update you later tnx Nothing to "try" actually, it's disabled by default, so a user can use the same login ID on multiple devices already. See image. [image: multiple.PNG] [image: multiple.PNG_thumb]

@triangleman: @Harvy66: Probably easier to re-install and restore your config from backup. You backup, right? And using ZFS would probably help prevent this in the future, at the cost of more memory. I'm all-for preventing this from happening again and will look into ZFS, but re-installing after a mere power failure seems a little much. Surely there's a way to use the 'recovery mode' from the CD to run FSCK on the disk right? I looked into it, FSCK does run, but i don't know how use it for this. I'm not familiar with UFS. Most modern filesystems don't trash committed data, only data or metadata changes that are in-flight run the risk of corruption. My pfSense box has experienced 3 unexpected power failures in the many years. Never had an issue, but could just be lucky or you could be unlucky or something pathological.

Yep, right before going in and setting it manually because it wasn't working either for some reason.  I'm just gonna restore it to defaults and go through the setup again.

I also tested this with another appliance with nearly no changes to the default configuration, but I get the same result. If anyone could tell me where i've might made a mistake that would be really appreciated.

Thanks. That seems like a good starting point. I looked the script /etc/rc.newwanipv6 and it looks like I have two options: a) Modify the script to call my script as well. But then I might have to change that file after every upgrade of pfsense, I'm assuming. b) At the end of the script, there is a function to restart packages. Maybe I could package my script, so it will be called from there automatically? Will have to investigate this a bit more…

Well stated Gertjan - but would like to clarify one small part.. Your not limited to the 1 (one) lan side port with vlans..  If you have multiple ports you can use them for multiple lan side networks..  As long as you have a switch you can connect your multiple ports from the router as different networks tagged or untagged. Router ports or interfaces are very valuable on a router - trying to bridge them to put in the same layer 2 network is waste of time, effort to end up with a more complex setup and less performance..  You might only do such a thing when you want to connect interface types…  Say you had a fiber connection on your router and you wanted this fiber connection to be in the same L2 network and as normal copper ethernet network. Or if you wanted to split the same L2 network but be able to firewall beside your split ends.. There are for sure uses of bridging interfaces on your router - but unless your doing something that is a bit more complex and requires such a setup... It going to be a much better idea to get just a vlan capable switch when you need more "ports"  leverage your routers interfaces as switch ports via bridging them not a good idea almost ever. If you need a few ports in the same network and you want them to be on your router box - get say the sg-3100, it has a 4 switch ports that you can use a switch in the same network or break them out as individual vlans, etc. But you can for sure get a 8 port get switch that is smart and easy to configure for like $30... If you want multiple interfaces on the same network - your way better off getting a switch then trying to bridge your very useful router interfaces.. It would be better to let those interfaces just sit unused for future use then try and leverage them as switch ports.  If your ocd and don't like these router ports left open - then use them in a lagg to your shiny new switch ;)  Be it your using 1 network or multiple vlans.

Hello forum, I need some help. I am not a networking expert. I am a noob to pfSense. I have my set up functional as this: Internet –> Cable Modem --> pfSense (Qotom) --> Dlink Switch (DGS1100 - 8 port easy smart) ---> Ubiquity AC Pro AP. The way configured now is simple. No Vlans defined. That is the part I need help on. What I want to accomplish is to have an SSID defined which will always route traffic via openVPN client (PIA). I have not defined the client yet - but I will be doing so once I am able to define vlans. Should I define Vlans on pfSense and also on Dlink Switch? If yes how do I instruct the Vlan defined on pfsense to use a specific port of the switch? The dlink Switch is only accessible on its own default IP. Should I connect to it and change it to an static IP of my choice so that I can access the web GUI of the switch? The Unifi AC Pro AP also has capability to identify the vlan for wireless traffic. So I must probably identify the tag for specific vlans for a particular SSID. Am I right? Appreciate the time spent on responding to my questions. Regards Guru

@jahonix: As long as both ends of a cable are configured the same way it doesn't matter. One manufacturer (r+m) made a comparison and found TIA568A to be capable of slightly faster transmission speeds than TIA568B. I cannot find the paper ATM though and can't explain why that should be. Just found on de.wikipedia that 568A is supposed to be the preferred standard in Europe and 568B is around in the US for historical reasons … oh well. The only difference between pairs is the twist rate.  Each pair has a different twist rate, to minimize cross talk.  However, with a 10 or 100 Mb cable,the same 2 pairs are used and only the signal direction reversed between A & B.  With Gigabit, all 4 pairs are used.  568B goes back to what eventually became 10baseT, StarLAN.  StarLAN was designed to share an existing 3 pair CAT3 cable with a telephone.  The phone would be on the first pair (blue/white), with the 2nd (orange/white) and 3rd (green/white) used for the LAN.  It also used a 6 position connector, as was common for phones.  This also means that Ethernet was designed to share a cable with phones, but that's not recommended practice now. https://en.wikipedia.org/wiki/StarLAN

@Grimson: @kcallis: This morning, in a moment of inspiration, I thought I would get tor working. So I configured polipo as well as tor and decided that it wasn't working for me. I removed the packages and find that I could no longer access the internet. Those aren't official packages, so whatever you did there probably messed with the pfSense install itself. Do a fresh install. I was hoping for a snazzy way to solve this problem, but the tried and true solution always win! I was just burning my USB thumb drive when I saw your response! K.

The startup/shutdown beeps use the PC Speaker and not a sound card. Disable the sound card.

If you want the servers in your DMZ to be accessible via IPv4, yes, you do.  If you have IPv6 available and you're happy with your DMZ devices being only accessible through IPv6 (assuming they support it), then there's no requirement that you create IPv4 port forwards.

Disregard, got it working. Forgot to create a new virtual interface on my NIC on Mac OS X box.

Did you add the firewall rule ? If you did try changing it to an any any rule and does it then work? https://doc.pfsense.org/index.php/IKEv2_with_EAP-MSCHAPv2#Add_Firewall_Rules_for_IPsec TBH I just followed https://doc.pfsense.org/index.php/IKEv2_with_EAP-MSCHAPv2 and it worked, I then tweaked my settings to suit what I wanted after.

Dude I have been doing this for over 30 years, getting paid to do it for 25.. Before there were real computers and "networks" ;) Just not possible to "teach" you security in a few posts… I can answer your questions on how to block or allow something specific in firewall rules.. More than happy to help you understand how to read the headers in an email message, etc. But you have not given any actual evidence of being "hacked"  more you have seen 1 too many movies or tv shows.. Did you just binge watch some episodes of Mr Robot? ;) Turning on pfsense is not going to fix your issue or really make you any more secure from being "hacked" than any off the shelf router.. When it comes down to it out of the box they do the same thing - they block unsolicited inbound and allow you out via a nat.  Its not a magic box you turn on and it makes your network secure from being "hacked".. It just a tool you use to secure your network.. But without the understanding of how to use the tool, its not some magic thing you turn on..  Many new users hear oh I can turn on IPS and will be secure from hackers - sorry it doesn't work that way.  If anything going to block the user from what they want to do when they want to do it.. And provide them with so much information it will just be overload of info they do not understand anyway.. For all we know you bought your phone off ebay and was jailbroken when you got it.. As to your bank account username and password being changed - sorry makes no sense.. Why would someone do that? And then not take any money?  Come on did you maybe forget your password?  And the username you norm use wouldn't work so its different than the normal username you pick... Maybe you smoked a bit of thee good stuff and got a bit paranoid after watching mr robot and thought someone changed your password - ie "hacked" you... Don't mean to make fun - You got some p0rn spam that said it was from you and your getting hacked? ??

Hi, The page you mentioned does exist - but I guess it isn't really part of the GUI anymore. From what I make of your question, you are using a tool that parses the html of that page to feed your own stats. That's ok, but understand that pfSense can change format, data, etc all the time. It's up to you to change your parsing tools. I guess that after changing the kernel version, from 9 to 10 to 11 (FreeBSD) interface internal naming, numbering, details, data, whatever, changed, so these pages are useless right now. Consider them as left overs from an old GUI version.  They have to be updated first if you want to see any data. Because you wrote - or at least: set up - de parser, you might as well 'repair' the pages graph.php (and ifstats.php). It's PHP, not a hassle for a "IT" guy. Btw : never ever keep old version 2.4.0 have been replaced by two newer version already, when asking questions you should use the latest, because now you are asking a question about a version that no one uses anymore … (not a problem of course, but your question becomes non-answerable).

Take a packet capture of the RADIUS auth exchange. Load it up in Wireshark and inspect the reply from the AD server, see if it has the Class attribute and how it looks.