Install ZFS on SG-1000? (corrupt filesystem)
-
"This has happened 3 times now"
So did you change the card? I had a pi with card that would corrupt at drop of hat as well.. Replaced the sd card and zero problems since..
-
"This has happened 3 times now"
**So did you change the card? **What card? There is no card. This is the internal eMMC (built in)
-
At the moment, there isn't a way to install with ZFS on there. I can't remember specifically if it was the low amount of RAM or if it was a U-Boot limitation though. For one reason or another we decided it wasn't feasible on that platform currently. That could definitely change in the future though.
-
What card? There is no card. This is the internal eMMC (built in)
You are correct.. My bad - but the image they have on the website for the sg-1000 sure looks like there is a card ;)
Does that not look like a SD card right there.. But yes in the specs it says
And on this view - shows a micro SD slot
But then on the specs says
Storage Options 4GB eMMC Flash on board -
What card? There is no card. This is the internal eMMC (built in)
You are correct.. My bad - but the image they have on the website for the sg-1000 sure looks like there is a card ;)
The SG-1000 has a eMMC built in and microSD card slot. You can use the microSD slot with your own microSD card in order to reinstall pfSense on the unit if you don't have or don't want to use the OTG USB cable.
-
"This has happened 3 times now"
**So did you change the card? **What card? There is no card. This is the internal eMMC (built in)
How are you doing this? We are aware of a few bugs related to the UFS and FreeBSD, but we are having hard time replicating it.
-
How are you doing this?
I downloaded the recovery image from the pfSense portal. I wrote it to a USB with Rufus and then booted that off the OTG cable. It worked fine, and I was up and running for about 2 hours. Then, during the regular configuration from the web GUI it crashed again and basically died - I saw it rebooting from the console after a kernel panic. I was in System > General at the time, just setting the time zone, system name, etc. Basic stuff. This is the 4th time now, so I think I am going to give up on this particular unit and see about RMA'ing it. The recovery image I used for the record was pfSense-netgate-uFW-recover-2.4.0-BETA-arm-20170402-1405.
-
How are you doing this?
I downloaded the recovery image from the pfSense portal. I wrote it to a USB with Rufus and then booted that off the OTG cable. It worked fine, and I was up and running for about 2 hours. Then, during the regular configuration from the web GUI it crashed again and basically died - I saw it rebooting from the console after a kernel panic. I was in System > General at the time, just setting the time zone, system name, etc. Basic stuff. This is the 4th time now, so I think I am going to give up on this particular unit and see about RMA'ing it. The recovery image I used for the record was pfSense-netgate-uFW-recover-2.4.0-BETA-arm-20170402-1405.
Yes, that was my next suggestion. It appears something is wrong with your unit, it should not behave like that. Sorry! Please send an email to support@netgate.com and someone will be able to assist you. I'll let support guys know about this. Thanks!
-
At the moment, there isn't a way to install with ZFS on there. I can't remember specifically if it was the low amount of RAM or if it was a U-Boot limitation though. For one reason or another we decided it wasn't feasible on that platform currently. That could definitely change in the future though.
In general, ZFS is not usable on 32 bit CPUs, such as the ARM TI AM3352 used on the SG-1000;
Up to 1-GHz Sitara™ ARM® Cortex®-A8 32-Bit RISC Processor -
ZFS support is not a goal on ARM until we get to arm64.