Dell PowerEdge R510 keeps locking up on install



  • Hi all,

    Just purchased a Dell R510 with 2 4-port Intel NIC's added to it.  I am unable to load pfSense 2.0 (either 32 or 64 bit).  The configuration or the install hangs at random points.  Any ideas of what I can look to?

    Thanks,

    Jeff



  • Maybe try a memtest cd to check for bad memory?



  • Hi,

    i'm sorry, i can't help you, but can you give me your configuration for your server please. Just the feature of the RAID controller because i have a r310 RAID0 with the perc H200 and no driver exist for this controller…  :'(



  • The RAID Controller is a SAS 6IR with (2) 250 GB SATA drives in a RAID-1.  (The OS appears to see the drives fine)

    The Dell Diagnostics pass and memtest passes.

    I can boot to the CD fine and walk through the wizard.  Sometimes it locks up when I plug the ethernet cable in during autodetect.  Sometimes it makes it through the wizard and locks up when "writing the configuration".  Sometimes it locks up during the install of the config to the hard drive (Option 99)

    Note:  I still have keyboard response.  I can even push the power button and initiate an orderly shutdown.  It's just the wizard that appears to get hung.

    I've gone through the BIOS and disabled all the CPU options, Power Saving, Memory, etc.

    I have been able to get the config and install to finish, with everything in the BIOS disabled.  However, going back and re-enabling things one by one (in order to isolate the issue) returns random results.  (Making it difficult to isolate)

    I'm now testing another scenario… I've pulled out the (2) Intel Gigabit ET Quad Port NICs and set all the bios settings back to the default.  I'll post back with the results...



  • Same problem with Intel NICs pulled.

    This time it hung at "Writing Configuration" again.



  • Try a external USB cdrom…. and check the MD5 of the .iso



  • I did check the MD5 of both 32 & 64 bit versions before I even started.

    I've now been able to successfully load and install 5 times in a row with the Intel Cards removed and the following BIOS settings:

    Processor Settings

    • Number of Cores per Processor = Single

    • C States = Disabled

    Integrated Devices

    • PXE boot disabled on NIC1

    • User Accessible USB Ports = Only Back Ports On

    Moved IRQ Assignments around for devices

    Power Management Set to "Max Performance"

    Now I've played with different combinations of these settings before (with the Intel NICs installed) and did not have consistent success.  ???

    I'll try re-installing the Intel NICs and see what happens with these same BIOS settings.



  • Try disable also the Bios configuration options, under 'Processor Settings', there is this: Virtualization Technology….



  • On this server, the Virtualization setting is disabled by default.  (I've also tried enabling it as well)

    I just put the NICs back in and had problems again.  This time the setup completed fine.  When I selected Option 99 to install to the hard drive I got the normal blue screen asking for the keyboard/regional settings, etc.  I selected Accept Settings as usual and then the next screen never loads (Just a blank blue screen).  I can hit <ctrl><c>to get back to the menu, but subsequent attempts to install to the hard drive just displays a blue screen with a message at the bottom saying "Waiting for backend"

    I just tried moving IRQs around again and will do more testing…</c></ctrl>



  • Moving IRQs resulted in the same issue… blank blue screen when trying to install to the hard drive.

    I then tried a USB DVD Drive to run the install from.  Same exact result.

    It's starting to look like something related to the Intel Quad Port NICs  (Maybe not... Had a hang after pulling nics)

    Continuing to test...



  • I've discovered that removing 1 of the quad port nic's enables consistent configuration and installation.  (Doesn't matter which nic)  As soon as I put the 2nd quad port nic in, I have problems.  I'm now trying to figure out why having both nic's installed causes problems…



  • Now I'm ticked…

    I just ordered 2 new Dell PE servers for production firewalls:

    R410 = 1 Dual Core CPU, SAS6ir, 1 Dual Port Broadcom NIC
    R510 = 2 Dual Core CPUs, SAS6ir, 2 Quad Port Intel NICs

    Having same issues with both servers!  This has got to be a freebsd thing, right?  Tomorrow, I'm going to try to load Untangle and see what happens.  My only other thought was to install ESXi and run pfSense as a VM.  But, I'm not real thrilled about that.



  • @the.it.dude:

    I've discovered that removing 1 of the quad port nic's enables consistent configuration and installation.  (Doesn't matter which nic)  As soon as I put the 2nd quad port nic in, I have problems.  I'm now trying to figure out why having both nic's installed causes problems…

    By I have problems do you mean the system locks up?

    Are the two quad port NICs indentical parts?

    Please post the output of the pfSense shell command # dmesg; vmstat -i on system with only one of the quad port NICs.

    @the.it.dude:

    Having same issues with both servers!

    What issues exactly? If you can't install on the R410 you could clone the disk from the R410 and use the clone in the R410 to get over the install problem. Does the R410 have two onboard NICs? If not, does it behave better with only one NIC in the system? Do you know if they are bce or bge NICs?



  • OK, Long Post.  But, everything should be in here now…  I'll create 2 seperate posts for the R410 & the R510:

    R410

    2 Internal NICs = Broadcom BCM5716 (bce)
    Add-in Dual Port NIC = Broadcom BCM5709 (bce)

    1st Test

    Add-in NIC removed and BIOS settings all set to default
    Everything OK!

    R410 w/o NIC installed

    $ dmesg; vmstat -i
    Copyright © 1992-2010 The FreeBSD Project.
    Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
    The Regents of the University of California. All rights reserved.
    FreeBSD is a registered trademark of The FreeBSD Foundation.
    FreeBSD 8.1-RELEASE-p2 #0: Sat Feb 26 18:05:58 EST 2011
        root@FreeBSD_8.0_pfSense_2.0-AMD64.snaps.pfsense.org:/usr/obj.pfSense/usr/pfSensesrc/src/sys/pfSense_SMP.8 amd64
    Timecounter "i8254" frequency 1193182 Hz quality 0
    CPU: Intel(R) Xeon(R) CPU          E5503  @ 2.00GHz (1995.01-MHz K8-class CPU)
      Origin = "GenuineIntel"  Id = 0x106a5  Family = 6  Model = 1a  Stepping = 5
      Features=0xbfebfbff <fpu,vme,de,pse,tsc,msr,pae,mce,cx8,apic,sep,mtrr,pge,mca,cmov,pat,pse36,clflush,dts,acpi,mmx,fxsr,sse,sse2,ss,htt,tm,pbe>Features2=0x9ce3bd <sse3,dtes64,mon,ds_cpl,vmx,est,tm2,ssse3,cx16,xtpr,pdcm,dca,sse4.1,sse4.2,popcnt>AMD Features=0x28100800 <syscall,nx,rdtscp,lm>AMD Features2=0x1 <lahf>TSC: P-state invariant
    real memory  = 2147483648 (2048 MB)
    avail memory = 2037293056 (1942 MB)
    ACPI APIC Table: <dell  pe_sc3 ="">FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs
    FreeBSD/SMP: 1 package(s) x 2 core(s)
    cpu0 (BSP): APIC ID: 16
    cpu1 (AP): APIC ID: 20
    ioapic1: Changing APIC ID to 1
    ioapic0 <version 2.0="">irqs 0-23 on motherboard
    ioapic1 <version 2.0="">irqs 32-55 on motherboard
    wpi: You need to read the LICENSE file in /usr/share/doc/legal/intel_wpi/.
    wpi: If you agree with the license, set legal.intel_wpi.license_ack=1 in /boot/loader.conf.
    module_register_init: MOD_LOAD (wpi_fw, 0xffffffff806512b0, 0) error 1
    ipw_bss: You need to read the LICENSE file in /usr/share/doc/legal/intel_ipw/.
    ipw_bss: If you agree with the license, set legal.intel_ipw.license_ack=1 in /boot/loader.conf.
    module_register_init: MOD_LOAD (ipw_bss_fw, 0xffffffff8046d080, 0) error 1
    ipw_ibss: You need to read the LICENSE file in /usr/share/doc/legal/intel_ipw/.
    ipw_ibss: If you agree with the license, set legal.intel_ipw.license_ack=1 in /boot/loader.conf.
    module_register_init: MOD_LOAD (ipw_ibss_fw, 0xffffffff8046d120, 0) error 1
    wlan: mac acl policy registered
    ipw_monitor: You need to read the LICENSE file in /usr/share/doc/legal/intel_ipw/.
    ipw_monitor: If you agree with the license, set legal.intel_ipw.license_ack=1 in /boot/loader.conf.
    module_register_init: MOD_LOAD (ipw_monitor_fw, 0xffffffff8046d1c0, 0) error 1
    kbd1 at kbdmux0
    cryptosoft0: <software crypto="">on motherboard
    padlock0: No ACE support.
    acpi0: <dell pe_sc3="">on motherboard
    acpi0: [ITHREAD]
    acpi0: Power Button (fixed)
    Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
    acpi_timer0: <24-bit timer at 3.579545MHz> port 0x808-0x80b on acpi0
    cpu0: <acpi cpu="">on acpi0
    cpu1: <acpi cpu="">on acpi0
    acpi_hpet0: <high precision="" event="" timer="">iomem 0xfed00000-0xfed003ff on acpi0
    Timecounter "HPET" frequency 14318180 Hz quality 900
    pcib0: <acpi host-pci="" bridge="">port 0xcf8-0xcff on acpi0
    pci0: <acpi pci="" bus="">on pcib0
    pcib1: <acpi pci-pci="" bridge="">at device 1.0 on pci0
    pci1: <acpi pci="" bus="">on pcib1
    bce0: <broadcom netxtreme="" ii="" bcm5716="" 1000base-t="" (c0)="">mem 0xda000000-0xdbffffff irq 36 at device 0.0 on pci1
    miibus0: <mii bus="">on bce0
    brgphy0: <bcm5709c 10="" 100="" 1000basetx="" phy="">PHY 1 on miibus0
    brgphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto
    bce0: [ITHREAD]
    bce0: ASIC (0x57092008); Rev (C0); Bus (PCIe x4, 2.5Gbps); B/C (5.2.3); Flags (MSI|MFW); MFW (NCSI 2.0.11)
    bce1: <broadcom netxtreme="" ii="" bcm5716="" 1000base-t="" (c0)="">mem 0xdc000000-0xddffffff irq 48 at device 0.1 on pci1
    miibus1: <mii bus="">on bce1
    brgphy1: <bcm5709c 10="" 100="" 1000basetx="" phy="">PHY 1 on miibus1
    brgphy1:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto
    bce1: [ITHREAD]
    bce1: ASIC (0x57092008); Rev (C0); Bus (PCIe x4, 2.5Gbps); B/C (5.2.3); Flags (MSI|MFW); MFW (NCSI 2.0.11)
    pcib2: <acpi pci-pci="" bridge="">at device 3.0 on pci0
    pci2: <acpi pci="" bus="">on pcib2
    mpt0: <lsilogic sas="" sata="" adapter="">port 0xfc00-0xfcff mem 0xdf2ec000-0xdf2effff,0xdf2f0000-0xdf2fffff irq 32 at device 0.0 on pci2
    mpt0: [ITHREAD]
    mpt0: MPI Version=1.5.18.0
    mpt0: Capabilities: ( RAID-0 RAID-1E RAID-1 )
    mpt0: 1 Active Volume (2 Max)
    mpt0: 2 Hidden Drive Members (14 Max)
    pcib3: <acpi pci-pci="" bridge="">at device 7.0 on pci0
    pci3: <acpi pci="" bus="">on pcib3
    pci0: <base peripheral,="" interrupt="" controller=""> at device 20.0 (no driver attached)
    pci0: <base peripheral,="" interrupt="" controller=""> at device 20.1 (no driver attached)
    pci0: <base peripheral,="" interrupt="" controller=""> at device 20.2 (no driver attached)
    uhci0: <intel 82801ji="" (ich10)="" usb="" controller="" usb-d="">port 0xec40-0xec5f irq 17 at device 26.0 on pci0
    uhci0: [ITHREAD]
    usbus0: <intel 82801ji="" (ich10)="" usb="" controller="" usb-d="">on uhci0
    uhci1: <intel 82801ji="" (ich10)="" usb="" controller="" usb-e="">port 0xec60-0xec7f irq 18 at device 26.1 on pci0
    uhci1: [ITHREAD]
    usbus1: <intel 82801ji="" (ich10)="" usb="" controller="" usb-e="">on uhci1
    ehci0: <intel 82801ji="" (ich10)="" usb="" 2.0="" controller="" usb-b="">mem 0xdf0fe000-0xdf0fe3ff irq 19 at device 26.7 on pci0
    ehci0: [ITHREAD]
    usbus2: EHCI version 1.0
    usbus2: <intel 82801ji="" (ich10)="" usb="" 2.0="" controller="" usb-b="">on ehci0
    uhci2: <intel 82801ji="" (ich10)="" usb="" controller="" usb-a="">port 0xec80-0xec9f irq 21 at device 29.0 on pci0
    uhci2: [ITHREAD]
    usbus3: <intel 82801ji="" (ich10)="" usb="" controller="" usb-a="">on uhci2
    uhci3: <intel 82801ji="" (ich10)="" usb="" controller="" usb-b="">port 0xeca0-0xecbf irq 20 at device 29.1 on pci0
    uhci3: [ITHREAD]
    usbus4: <intel 82801ji="" (ich10)="" usb="" controller="" usb-b="">on uhci3
    uhci4: <intel 82801ji="" (ich10)="" usb="" controller="" usb-c="">port 0xecc0-0xecdf irq 21 at device 29.2 on pci0
    uhci4: [ITHREAD]
    usbus5: <intel 82801ji="" (ich10)="" usb="" controller="" usb-c="">on uhci4
    uhci5: <intel 82801ji="" (ich10)="" usb="" controller="" usb-f="">port 0xece0-0xecff irq 20 at device 29.3 on pci0
    uhci5: [ITHREAD]
    usbus6: <intel 82801ji="" (ich10)="" usb="" controller="" usb-f="">on uhci5
    ehci1: <intel 82801ji="" (ich10)="" usb="" 2.0="" controller="" usb-a="">mem 0xdf0ff000-0xdf0ff3ff irq 21 at device 29.7 on pci0
    ehci1: [ITHREAD]
    usbus7: EHCI version 1.0
    usbus7: <intel 82801ji="" (ich10)="" usb="" 2.0="" controller="" usb-a="">on ehci1
    pcib4: <acpi pci-pci="" bridge="">at device 30.0 on pci0
    pci4: <acpi pci="" bus="">on pcib4
    vgapci0: <vga-compatible display="">mem 0xd9800000-0xd9ffffff,0xde7fc000-0xde7fffff,0xde800000-0xdeffffff irq 19 at device 3.0 on pci4
    isab0: <pci-isa bridge="">at device 31.0 on pci0
    isa0: <isa bus="">on isab0
    atapci0: <intel ich10="" sata300="" controller="">port 0xe8e0-0xe8e7,0xe8d0-0xe8d3,0xe8e8-0xe8ef,0xe8d4-0xe8d7,0xec00-0xec0f,0xec10-0xec1f irq 23 at device 31.2 on pci0
    atapci0: [ITHREAD]
    ata2: <ata 0="" channel="">on atapci0
    ata2: [ITHREAD]
    ata3: <ata 1="" channel="">on atapci0
    ata3: [ITHREAD]
    atapci1: <intel ich10="" sata300="" controller="">port 0xe8f0-0xe8f7,0xe8d8-0xe8db,0xe8f8-0xe8ff,0xe8dc-0xe8df,0xec20-0xec2f,0xec30-0xec3f irq 22 at device 31.5 on pci0
    atapci1: [ITHREAD]
    ata4: <ata 0="" channel="">on atapci1
    ata4: [ITHREAD]
    ata5: <ata 1="" channel="">on atapci1
    ata5: [ITHREAD]
    atrtc0: <at realtime="" clock="">port 0x70-0x7f irq 8 on acpi0
    uart0: <16550 or compatible> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0
    uart0: [FILTER]
    uart1: <16550 or compatible> port 0x2f8-0x2ff irq 3 on acpi0
    uart1: [FILTER]
    orm0: <isa option="" roms="">at iomem 0xc0000-0xc7fff,0xce000-0xcefff,0xec000-0xeffff on isa0
    sc0: <system console="">at flags 0x100 on isa0
    sc0: VGA <16 virtual consoles, flags=0x300>
    vga0: <generic isa="" vga="">at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
    atkbdc0: <keyboard controller="" (i8042)="">at port 0x60,0x64 on isa0
    atkbd0: <at keyboard="">irq 1 on atkbdc0
    kbd0 at atkbd0
    atkbd0: [GIANT-LOCKED]
    atkbd0: [ITHREAD]
    ppc0: cannot reserve I/O port range
    est0: <enhanced speedstep="" frequency="" control="">on cpu0
    est: CPU supports Enhanced Speedstep, but is not recognized.
    est: cpu_vendor GenuineIntel, msr f
    device_attach: est0 attach returned 6
    p4tcc0: <cpu frequency="" thermal="" control="">on cpu0
    est1: <enhanced speedstep="" frequency="" control="">on cpu1
    est: CPU supports Enhanced Speedstep, but is not recognized.
    est: cpu_vendor GenuineIntel, msr f
    device_attach: est1 attach returned 6
    p4tcc1: <cpu frequency="" thermal="" control="">on cpu1
    Timecounters tick every 1.000 msec
    IPsec: Initialized Security Association Processing.
    usbus0: 12Mbps Full Speed USB v1.0
    usbus1: 12Mbps Full Speed USB v1.0
    usbus2: 480Mbps High Speed USB v2.0
    usbus3: 12Mbps Full Speed USB v1.0
    usbus4: 12Mbps Full Speed USB v1.0
    usbus5: 12Mbps Full Speed USB v1.0
    usbus6: 12Mbps Full Speed USB v1.0
    usbus7: 480Mbps High Speed USB v2.0
    mpt0:vol0(mpt0:0:0): Settings ( Member-WCE Hot-Plug-Spares High-Priority-ReSync )ugen0.1: <intel>at usbus0
    uhub0: <intel 1="" 9="" uhci="" root="" hub,="" class="" 0,="" rev="" 1.00="" 1.00,="" addr="">on usbus0
    ugen1.1: <intel>at usbus1
    uhub1: <intel 1="" 9="" uhci="" root="" hub,="" class="" 0,="" rev="" 1.00="" 1.00,="" addr="">on usbus1
    ugen2.1: <intel>at usbus2
    uhub2: <intel 1="" 9="" ehci="" root="" hub,="" class="" 0,="" rev="" 2.00="" 1.00,="" addr="">on usbus2
    ugen3.1: <intel>at usbus3
    uhub3: <intel 1="" 9="" uhci="" root="" hub,="" class="" 0,="" rev="" 1.00="" 1.00,="" addr="">on usbus3
    ugen4.1: <intel>at usbus4
    uhub4: <intel 1="" 9="" uhci="" root="" hub,="" class="" 0,="" rev="" 1.00="" 1.00,="" addr="">on usbus4
    ugen5.1: <intel>at usbus5
    uhub5: <intel 1="" 9="" uhci="" root="" hub,="" class="" 0,="" rev="" 1.00="" 1.00,="" addr="">on usbus5
    ugen6.1: <intel>at usbus6
    uhub6: <intel 1="" 9="" uhci="" root="" hub,="" class="" 0,="" rev="" 1.00="" 1.00,="" addr="">on usbus6
    ugen7.1: <intel>at usbus7
    uhub7: <intel 1="" 9="" ehci="" root="" hub,="" class="" 0,="" rev="" 2.00="" 1.00,="" addr="">on usbus7

    mpt0:vol0(mpt0:0:0): Using Spare Pool: 0
    mpt0:vol0(mpt0:0:0): 2 Members:
          (mpt0:1:8:0): Primary Online
          (mpt0:1:1:0): Secondary Online
    mpt0:vol0(mpt0:0:0): RAID-1 - Optimal
    mpt0:vol0(mpt0:0:0): Status ( Enabled )
    (mpt0:vol0:1): Physical (mpt0:0:1:0), Pass-thru (mpt0:1:0:0)
    (mpt0:vol0:1): Online
    (mpt0:vol0:0): Physical (mpt0:0:8:0), Pass-thru (mpt0:1:1:0)
    (mpt0:vol0:0): Online
    uhub0: 2 ports with 2 removable, self powered
    uhub1: 2 ports with 2 removable, self powered
    uhub3: 2 ports with 2 removable, self powered
    uhub4: 2 ports with 2 removable, self powered
    uhub5: 2 ports with 2 removable, self powered
    uhub6: 2 ports with 2 removable, self powered
    uhub2: 4 ports with 4 removable, self powered
    uhub7: 4 ports with 4 removable, self powered
    pass1 at mpt0 bus 1 scbus1 target 0 lun 0
    pass1: <ata wdc="" wd2502abys-1="" 3b05="">Fixed Uninstalled SCSI-5 device
    pass1: 300.000MB/s transfers
    pass1: Command Queueing enabled
    da0 at mpt0 bus 0 scbus0 target 0 lun 0
    da0: <dell 1028="" virtual="" disk="">Fixed Direct Access SCSI-5 device
    da0: 300.000MB/s transfers
    da0: Command Queueing enabled
    da0: 237824MB (487063552 512 byte sectors: 255H 63S/T 30318C)
    acd0: DVDROM <teac dvd-rom="" dv-28sw="" r.2a="">at ata4-master UDMA100 SATA 1.5Gb/s
    SMP: AP CPU #1 Launched!
    ugen2.2: <vendor 0x0424="">at usbus2
    uhub8: <vendor 2="" 9="" 0x0424="" product="" 0x2514,="" class="" 0,="" rev="" 2.00="" 0.00,="" addr="">on usbus2
    ugen0.2: <dell>at usbus0
    ukbd0: <ep1 interrupt="">on usbus0
    kbd2 at ukbd0
    uhub8: 2 ports with 2 removable, self powered
    Trying to mount root from cd9660:/dev/iso9660/pfSense
    md0.uzip: 3159 x 65536 blocks
    pflog0: promiscuous mode enabled
    interrupt                          total      rate
    irq17: uhci0                          49          0
    irq19: ehci0                        147          0
    irq22: atapci1                      3746        14
    irq32: mpt0                          425          1
    cpu0: timer                      502014      1976
    irq256: bce0                          1          0
    irq257: bce1                        753          2
    cpu1: timer                      493465      1942
    Total                            1000600      3939

    2nd Test

    Install Add-in Dual Port NIC to already installed pfSense on hard drive
    Assign Interfaces
    Everything OK!

    R410 w/ NIC Installed

    $ dmesg; vmstat -i
    Copyright © 1992-2010 The FreeBSD Project.
    Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
    The Regents of the University of California. All rights reserved.
    FreeBSD is a registered trademark of The FreeBSD Foundation.
    FreeBSD 8.1-RELEASE-p2 #0: Sat Feb 26 18:05:58 EST 2011
        root@FreeBSD_8.0_pfSense_2.0-AMD64.snaps.pfsense.org:/usr/obj.pfSense/usr/pfSensesrc/src/sys/pfSense_SMP.8 amd64
    Timecounter "i8254" frequency 1193182 Hz quality 0
    CPU: Intel(R) Xeon(R) CPU          E5503  @ 2.00GHz (1995.01-MHz K8-class CPU)
      Origin = "GenuineIntel"  Id = 0x106a5  Family = 6  Model = 1a  Stepping = 5
      Features=0xbfebfbff <fpu,vme,de,pse,tsc,msr,pae,mce,cx8,apic,sep,mtrr,pge,mca,cmov,pat,pse36,clflush,dts,acpi,mmx,fxsr,sse,sse2,ss,htt,tm,pbe>Features2=0x9ce3bd <sse3,dtes64,mon,ds_cpl,vmx,est,tm2,ssse3,cx16,xtpr,pdcm,dca,sse4.1,sse4.2,popcnt>AMD Features=0x28100800 <syscall,nx,rdtscp,lm>AMD Features2=0x1 <lahf>TSC: P-state invariant
    real memory  = 2147483648 (2048 MB)
    avail memory = 2037805056 (1943 MB)
    ACPI APIC Table: <dell  pe_sc3 ="">FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs
    FreeBSD/SMP: 1 package(s) x 2 core(s)
    cpu0 (BSP): APIC ID: 16
    cpu1 (AP): APIC ID: 20
    ioapic1: Changing APIC ID to 1
    ioapic0 <version 2.0="">irqs 0-23 on motherboard
    ioapic1 <version 2.0="">irqs 32-55 on motherboard
    wpi: You need to read the LICENSE file in /usr/share/doc/legal/intel_wpi/.
    wpi: If you agree with the license, set legal.intel_wpi.license_ack=1 in /boot/loader.conf.
    module_register_init: MOD_LOAD (wpi_fw, 0xffffffff806512b0, 0) error 1
    ipw_bss: You need to read the LICENSE file in /usr/share/doc/legal/intel_ipw/.
    ipw_bss: If you agree with the license, set legal.intel_ipw.license_ack=1 in /boot/loader.conf.
    module_register_init: MOD_LOAD (ipw_bss_fw, 0xffffffff8046d080, 0) error 1
    ipw_ibss: You need to read the LICENSE file in /usr/share/doc/legal/intel_ipw/.
    ipw_ibss: If you agree with the license, set legal.intel_ipw.license_ack=1 in /boot/loader.conf.
    module_register_init: MOD_LOAD (ipw_ibss_fw, 0xffffffff8046d120, 0) error 1
    wlan: mac acl policy registered
    ipw_monitor: You need to read the LICENSE file in /usr/share/doc/legal/intel_ipw/.
    ipw_monitor: If you agree with the license, set legal.intel_ipw.license_ack=1 in /boot/loader.conf.
    module_register_init: MOD_LOAD (ipw_monitor_fw, 0xffffffff8046d1c0, 0) error 1
    kbd1 at kbdmux0
    cryptosoft0: <software crypto="">on motherboard
    padlock0: No ACE support.
    acpi0: <dell pe_sc3="">on motherboard
    acpi0: [ITHREAD]
    acpi0: Power Button (fixed)
    Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
    acpi_timer0: <24-bit timer at 3.579545MHz> port 0x808-0x80b on acpi0
    cpu0: <acpi cpu="">on acpi0
    cpu1: <acpi cpu="">on acpi0
    acpi_hpet0: <high precision="" event="" timer="">iomem 0xfed00000-0xfed003ff on acpi0
    Timecounter "HPET" frequency 14318180 Hz quality 900
    pcib0: <acpi host-pci="" bridge="">port 0xcf8-0xcff on acpi0
    pci0: <acpi pci="" bus="">on pcib0
    pcib1: <acpi pci-pci="" bridge="">at device 1.0 on pci0
    pci1: <acpi pci="" bus="">on pcib1
    bce0: <broadcom netxtreme="" ii="" bcm5716="" 1000base-t="" (c0)="">mem 0xd6000000-0xd7ffffff irq 36 at device 0.0 on pci1
    miibus0: <mii bus="">on bce0
    brgphy0: <bcm5709c 10="" 100="" 1000basetx="" phy="">PHY 1 on miibus0
    brgphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto
    bce0: [ITHREAD]
    bce0: ASIC (0x57092008); Rev (C0); Bus (PCIe x4, 2.5Gbps); B/C (5.2.3); Flags (MSI|MFW); MFW (NCSI 2.0.11)
    bce1: <broadcom netxtreme="" ii="" bcm5716="" 1000base-t="" (c0)="">mem 0xd8000000-0xd9ffffff irq 48 at device 0.1 on pci1
    miibus1: <mii bus="">on bce1
    brgphy1: <bcm5709c 10="" 100="" 1000basetx="" phy="">PHY 1 on miibus1
    brgphy1:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto
    bce1: [ITHREAD]
    bce1: ASIC (0x57092008); Rev (C0); Bus (PCIe x4, 2.5Gbps); B/C (5.2.3); Flags (MSI|MFW); MFW (NCSI 2.0.11)
    pcib2: <acpi pci-pci="" bridge="">at device 3.0 on pci0
    pci2: <acpi pci="" bus="">on pcib2
    mpt0: <lsilogic sas="" sata="" adapter="">port 0xfc00-0xfcff mem 0xdf2ec000-0xdf2effff,0xdf2f0000-0xdf2fffff irq 32 at device 0.0 on pci2
    mpt0: [ITHREAD]
    mpt0: MPI Version=1.5.18.0
    mpt0: Capabilities: ( RAID-0 RAID-1E RAID-1 )
    mpt0: 1 Active Volume (2 Max)
    mpt0: 2 Hidden Drive Members (14 Max)
    pcib3: <acpi pci-pci="" bridge="">at device 7.0 on pci0
    pci3: <acpi pci="" bus="">on pcib3
    bce2: <broadcom netxtreme="" ii="" bcm5709="" 1000base-t="" (c0)="">mem 0xda000000-0xdbffffff irq 38 at device 0.0 on pci3
    miibus2: <mii bus="">on bce2
    brgphy2: <bcm5709c 10="" 100="" 1000basetx="" phy="">PHY 1 on miibus2
    brgphy2:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto
    bce2: [ITHREAD]
    bce2: ASIC (0x57092003); Rev (C0); Bus (PCIe x4, 2.5Gbps); B/C (5.2.3); Flags (MSI)
    bce3: <broadcom netxtreme="" ii="" bcm5709="" 1000base-t="" (c0)="">mem 0xdc000000-0xddffffff irq 45 at device 0.1 on pci3
    miibus3: <mii bus="">on bce3
    brgphy3: <bcm5709c 10="" 100="" 1000basetx="" phy="">PHY 1 on miibus3
    brgphy3:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto
    bce3: [ITHREAD]
    bce3: ASIC (0x57092003); Rev (C0); Bus (PCIe x4, 2.5Gbps); B/C (5.2.3); Flags (MSI)
    pci0: <base peripheral,="" interrupt="" controller=""> at device 20.0 (no driver attached)
    pci0: <base peripheral,="" interrupt="" controller=""> at device 20.1 (no driver attached)
    pci0: <base peripheral,="" interrupt="" controller=""> at device 20.2 (no driver attached)
    uhci0: <intel 82801ji="" (ich10)="" usb="" controller="" usb-d="">port 0xec40-0xec5f irq 17 at device 26.0 on pci0
    uhci0: [ITHREAD]
    usbus0: <intel 82801ji="" (ich10)="" usb="" controller="" usb-d="">on uhci0
    uhci1: <intel 82801ji="" (ich10)="" usb="" controller="" usb-e="">port 0xec60-0xec7f irq 18 at device 26.1 on pci0
    uhci1: [ITHREAD]
    usbus1: <intel 82801ji="" (ich10)="" usb="" controller="" usb-e="">on uhci1
    ehci0: <intel 82801ji="" (ich10)="" usb="" 2.0="" controller="" usb-b="">mem 0xdf0fe000-0xdf0fe3ff irq 19 at device 26.7 on pci0
    ehci0: [ITHREAD]
    usbus2: EHCI version 1.0
    usbus2: <intel 82801ji="" (ich10)="" usb="" 2.0="" controller="" usb-b="">on ehci0
    uhci2: <intel 82801ji="" (ich10)="" usb="" controller="" usb-a="">port 0xec80-0xec9f irq 21 at device 29.0 on pci0
    uhci2: [ITHREAD]
    usbus3: <intel 82801ji="" (ich10)="" usb="" controller="" usb-a="">on uhci2
    uhci3: <intel 82801ji="" (ich10)="" usb="" controller="" usb-b="">port 0xeca0-0xecbf irq 20 at device 29.1 on pci0
    uhci3: [ITHREAD]
    usbus4: <intel 82801ji="" (ich10)="" usb="" controller="" usb-b="">on uhci3
    uhci4: <intel 82801ji="" (ich10)="" usb="" controller="" usb-c="">port 0xecc0-0xecdf irq 21 at device 29.2 on pci0
    uhci4: [ITHREAD]
    usbus5: <intel 82801ji="" (ich10)="" usb="" controller="" usb-c="">on uhci4
    uhci5: <intel 82801ji="" (ich10)="" usb="" controller="" usb-f="">port 0xece0-0xecff irq 20 at device 29.3 on pci0
    uhci5: [ITHREAD]
    usbus6: <intel 82801ji="" (ich10)="" usb="" controller="" usb-f="">on uhci5
    ehci1: <intel 82801ji="" (ich10)="" usb="" 2.0="" controller="" usb-a="">mem 0xdf0ff000-0xdf0ff3ff irq 21 at device 29.7 on pci0
    ehci1: [ITHREAD]
    usbus7: EHCI version 1.0
    usbus7: <intel 82801ji="" (ich10)="" usb="" 2.0="" controller="" usb-a="">on ehci1
    pcib4: <acpi pci-pci="" bridge="">at device 30.0 on pci0
    pci4: <acpi pci="" bus="">on pcib4
    vgapci0: <vga-compatible display="">mem 0xd5800000-0xd5ffffff,0xde7fc000-0xde7fffff,0xde800000-0xdeffffff irq 19 at device 3.0 on pci4
    isab0: <pci-isa bridge="">at device 31.0 on pci0
    isa0: <isa bus="">on isab0
    atapci0: <intel ich10="" sata300="" controller="">port 0xe8e0-0xe8e7,0xe8d0-0xe8d3,0xe8e8-0xe8ef,0xe8d4-0xe8d7,0xec00-0xec0f,0xec10-0xec1f irq 23 at device 31.2 on pci0
    atapci0: [ITHREAD]
    ata2: <ata 0="" channel="">on atapci0
    ata2: [ITHREAD]
    ata3: <ata 1="" channel="">on atapci0
    ata3: [ITHREAD]
    atapci1: <intel ich10="" sata300="" controller="">port 0xe8f0-0xe8f7,0xe8d8-0xe8db,0xe8f8-0xe8ff,0xe8dc-0xe8df,0xec20-0xec2f,0xec30-0xec3f irq 22 at device 31.5 on pci0
    atapci1: [ITHREAD]
    ata4: <ata 0="" channel="">on atapci1
    ata4: [ITHREAD]
    ata5: <ata 1="" channel="">on atapci1
    ata5: [ITHREAD]
    atrtc0: <at realtime="" clock="">port 0x70-0x7f irq 8 on acpi0
    uart0: <16550 or compatible> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0
    uart0: [FILTER]
    uart1: <16550 or compatible> port 0x2f8-0x2ff irq 3 on acpi0
    uart1: [FILTER]
    orm0: <isa option="" roms="">at iomem 0xc0000-0xc7fff,0xce000-0xcefff,0xec000-0xeffff on isa0
    sc0: <system console="">at flags 0x100 on isa0
    sc0: VGA <16 virtual consoles, flags=0x300>
    vga0: <generic isa="" vga="">at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
    atkbdc0: <keyboard controller="" (i8042)="">at port 0x60,0x64 on isa0
    atkbd0: <at keyboard="">irq 1 on atkbdc0
    kbd0 at atkbd0
    atkbd0: [GIANT-LOCKED]
    atkbd0: [ITHREAD]
    ppc0: cannot reserve I/O port range
    est0: <enhanced speedstep="" frequency="" control="">on cpu0
    est: CPU supports Enhanced Speedstep, but is not recognized.
    est: cpu_vendor GenuineIntel, msr f
    device_attach: est0 attach returned 6
    p4tcc0: <cpu frequency="" thermal="" control="">on cpu0
    est1: <enhanced speedstep="" frequency="" control="">on cpu1
    est: CPU supports Enhanced Speedstep, but is not recognized.
    est: cpu_vendor GenuineIntel, msr f
    device_attach: est1 attach returned 6
    p4tcc1: <cpu frequency="" thermal="" control="">on cpu1
    Timecounters tick every 1.000 msec
    IPsec: Initialized Security Association Processing.
    usbus0: 12Mbps Full Speed USB v1.0
    usbus1: 12Mbps Full Speed USB v1.0
    usbus2: 480Mbps High Speed USB v2.0
    usbus3: 12Mbps Full Speed USB v1.0
    usbus4: 12Mbps Full Speed USB v1.0
    usbus5: 12Mbps Full Speed USB v1.0
    usbus6: 12Mbps Full Speed USB v1.0
    usbus7: 480Mbps High Speed USB v2.0
    mpt0:vol0(mpt0:0:0): Settings (ugen0.1: <intel>at usbus0
    uhub0: <intel 1="" 9="" uhci="" root="" hub,="" class="" 0,="" rev="" 1.00="" 1.00,="" addr="">on usbus0
    ugen1.1: <intel>at usbus1
    uhub1: <intel 1="" 9="" uhci="" root="" hub,="" class="" 0,="" rev="" 1.00="" 1.00,="" addr="">on usbus1
    ugen2.1: <intel>at usbus2
    uhub2: <intel 1="" 9="" ehci="" root="" hub,="" class="" 0,="" rev="" 2.00="" 1.00,="" addr="">on usbus2
    ugen3.1: <intel>at usbus3
    uhub3: <intel 1="" 9="" uhci="" root="" hub,="" class="" 0,="" rev="" 1.00="" 1.00,="" addr="">on usbus3
    ugen4.1: <intel>at usbus4
    uhub4: <intel 1="" 9="" uhci="" root="" hub,="" class="" 0,="" rev="" 1.00="" 1.00,="" addr="">on usbus4
    ugen5.1: <intel>at usbus5
    uhub5: <intel 1="" 9="" uhci="" root="" hub,="" class="" 0,="" rev="" 1.00="" 1.00,="" addr="">on usbus5
    ugen6.1: <intel>at usbus6
    uhub6: <intel 1="" 9="" uhci="" root="" hub,="" class="" 0,="" rev="" 1.00="" 1.00,="" addr="">on usbus6
    ugen7.1: <intel>at usbus7
    uhub7: <intel 1="" 9="" ehci="" root="" hub,="" class="" 0,="" rev="" 2.00="" 1.00,="" addr="">on usbus7
    Member-WCE Hot-Plug-Spares High-Priority-ReSync )
    mpt0:vol0(mpt0:0:0): Using Spare Pool: 0
    mpt0:vol0(mpt0:0:0): 2 Members:
          (mpt0:1:8:0): Primary Online
          (mpt0:1:1:0): Secondary Online
    mpt0:vol0(mpt0:0:0): RAID-1 - Optimal
    mpt0:vol0(mpt0:0:0): Status ( Enabled )
    (mpt0:vol0:1): Physical (mpt0:0:1:0), Pass-thru (mpt0:1:0:0)
    (mpt0:vol0:1): Online
    (mpt0:vol0:0): Physical (mpt0:0:8:0), Pass-thru (mpt0:1:1:0)
    (mpt0:vol0:0): Online
    uhub0: 2 ports with 2 removable, self powered
    uhub1: 2 ports with 2 removable, self powered
    uhub3: 2 ports with 2 removable, self powered
    uhub4: 2 ports with 2 removable, self powered
    uhub5: 2 ports with 2 removable, self powered
    uhub6: 2 ports with 2 removable, self powered
    uhub2: 4 ports with 4 removable, self powered
    uhub7: 4 ports with 4 removable, self powered
    pass1 at mpt0 bus 1 scbus1 target 0 lun 0
    pass1: <ata wdc="" wd2502abys-1="" 3b05="">Fixed Uninstalled SCSI-5 device
    pass1: 300.000MB/s transfers
    pass1: Command Queueing enabled
    da0 at mpt0 bus 0 scbus0 target 0 lun 0
    da0: <dell 1028="" virtual="" disk="">Fixed Direct Access SCSI-5 device
    da0: 300.000MB/s transfers
    da0: Command Queueing enabled
    da0: 237824MB (487063552 512 byte sectors: 255H 63S/T 30318C)
    acd0: DVDROM <teac dvd-rom="" dv-28sw="" r.2a="">at ata4-master UDMA100 SATA 1.5Gb/s
    SMP: AP CPU #1 Launched!
    Root mount waiting for: usbus2
    ugen2.2: <vendor 0x0424="">at usbus2
    uhub8: <vendor 2="" 9="" 0x0424="" product="" 0x2514,="" class="" 0,="" rev="" 2.00="" 0.00,="" addr="">on usbus2
    ugen0.2: <dell>at usbus0
    ukbd0: <ep1 interrupt="">on usbus0
    kbd2 at ukbd0
    uhub8: 2 ports with 2 removable, self powered
    Trying to mount root from ufs:/dev/da0s1a
    pflog0: promiscuous mode enabled
    bce1: link state changed to UP
    interrupt                          total      rate
    irq17: uhci0                          19          0
    irq19: ehci0                          48          0
    irq22: atapci1                        68          1
    irq32: mpt0                        2049        35
    cpu0: timer                      114559      1975
    irq256: bce0                          1          0
    irq257: bce1                        413          7
    cpu1: timer                      106013      1827
    Total                            223170      3847

    3rd Test

    Restart LiveCD with Add-in NIC installed and BIOS Settings at Default
    Completes LiveCD boot and configuration.
    Enter Option 99 to Install to Hard Drive
      Configure Console - Enter to "Accept these Settings"
      I never get the next screen.  I just see a blue screen w/ F10=Refresh Display in the upper left.
      I can hit <ctrl><c>to get back to the menu

    What about running the install with the add-in nic installed causes a problem with installing to the hard drive?</c></ctrl></ep1></dell></vendor></vendor></teac></dell></ata></intel></intel></intel></intel></intel></intel></intel></intel></intel></intel></intel></intel></intel></intel></intel></intel></cpu></enhanced></cpu></enhanced></at></keyboard></generic></system></isa></at></ata></ata></intel></ata></ata></intel></isa></pci-isa></vga-compatible></acpi></acpi></intel></intel></intel></intel></intel></intel></intel></intel></intel></intel></intel></intel></intel></intel></intel></intel></bcm5709c></mii></broadcom></bcm5709c></mii></broadcom></acpi></acpi></lsilogic></acpi></acpi></bcm5709c></mii></broadcom></bcm5709c></mii></broadcom></acpi></acpi></acpi></acpi></high></acpi></acpi></dell></software></version></version></dell ></lahf></syscall,nx,rdtscp,lm></sse3,dtes64,mon,ds_cpl,vmx,est,tm2,ssse3,cx16,xtpr,pdcm,dca,sse4.1,sse4.2,popcnt></fpu,vme,de,pse,tsc,msr,pae,mce,cx8,apic,sep,mtrr,pge,mca,cmov,pat,pse36,clflush,dts,acpi,mmx,fxsr,sse,sse2,ss,htt,tm,pbe></ep1></dell></vendor></vendor></teac></dell></ata></intel></intel></intel></intel></intel></intel></intel></intel></intel></intel></intel></intel></intel></intel></intel></intel></cpu></enhanced></cpu></enhanced></at></keyboard></generic></system></isa></at></ata></ata></intel></ata></ata></intel></isa></pci-isa></vga-compatible></acpi></acpi></intel></intel></intel></intel></intel></intel></intel></intel></intel></intel></intel></intel></intel></intel></intel></intel></acpi></acpi></lsilogic></acpi></acpi></bcm5709c></mii></broadcom></bcm5709c></mii></broadcom></acpi></acpi></acpi></acpi></high></acpi></acpi></dell></software></version></version></dell ></lahf></syscall,nx,rdtscp,lm></sse3,dtes64,mon,ds_cpl,vmx,est,tm2,ssse3,cx16,xtpr,pdcm,dca,sse4.1,sse4.2,popcnt></fpu,vme,de,pse,tsc,msr,pae,mce,cx8,apic,sep,mtrr,pge,mca,cmov,pat,pse36,clflush,dts,acpi,mmx,fxsr,sse,sse2,ss,htt,tm,pbe>



  • R510

    2 Internal NICs = Broadcom BCM5716 (bce)
    2 Add-in Quad Port NICs = Intel PRO/1000 v. 2.0.7 (igb)

    1st Test

    Both Add-in NICs removed
    BIOS Settings at default

    During Boot, right after prompt for:
      (R)ecovery mode…
      (I)nstaller...
      (C) Continues the LiveCD bootup...

    I see the following on screen:

    Loading Configuration......done.
    Network intface mismatch -- Running interface assignment option.
    bce1: link state changed to DOWN
    bce1: link state changed to UP

    And then nothing...  Just a non-blinking cursor
    The Keyboard works... if I hit <enter>, I see carriage returns on the screen, but nothing else
    If I hit the power button on the server, I see:
      acpi0: suspend request ignored (not ready yet)
      acpi0: request to enter state S5 failed (err 6)

    Subsequent attempts with the same settings worked fine

    Could not re-create that 1st problem
    Everything Works!

    2nd Test

    Added 1 Add-In Quad Port NIC to already installed pfSense
    Assigned Interfaces
    Everything Works!

    R510 w/ 1 of the Quad Port NICs installed

    $ dmesg; vmstat -i
    Copyright © 1992-2010 The FreeBSD Project.
    Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
    The Regents of the University of California. All rights reserved.
    FreeBSD is a registered trademark of The FreeBSD Foundation.
    FreeBSD 8.1-RELEASE-p2 #0: Sat Feb 26 15:29:09 EST 2011
        sullrich@FreeBSD_8.0_pfSense_2.0-snaps.pfsense.org:/usr/obj.pfSense/usr/pfSensesrc/src/sys/pfSense_SMP.8 i386
    Timecounter "i8254" frequency 1193182 Hz quality 0
    CPU: Intel(R) Xeon(R) CPU          E5503  @ 2.00GHz (2000.08-MHz 686-class CPU)
      Origin = "GenuineIntel"  Id = 0x106a5  Family = 6  Model = 1a  Stepping = 5
      Features=0xbfebfbff <fpu,vme,de,pse,tsc,msr,pae,mce,cx8,apic,sep,mtrr,pge,mca,cmov,pat,pse36,clflush,dts,acpi,mmx,fxsr,sse,sse2,ss,htt,tm,pbe>Features2=0x9ce3bd <sse3,dtes64,mon,ds_cpl,vmx,est,tm2,ssse3,cx16,xtpr,pdcm,dca,sse4.1,sse4.2,popcnt>AMD Features=0x28100000 <nx,rdtscp,lm>AMD Features2=0x1 <lahf>TSC: P-state invariant
    real memory  = 2147483648 (2048 MB)
    avail memory = 2069499904 (1973 MB)
    ACPI APIC Table: <dell  pe_sc3 ="">FreeBSD/SMP: Multiprocessor System Detected: 4 CPUs
    FreeBSD/SMP: 2 package(s) x 2 core(s)
    cpu0 (BSP): APIC ID: 16
    cpu1 (AP): APIC ID: 20
    cpu2 (AP): APIC ID:  0
    cpu3 (AP): APIC ID:  4
    ioapic1: Changing APIC ID to 1
    ioapic0 <version 2.0="">irqs 0-23 on motherboard
    ioapic1 <version 2.0="">irqs 32-55 on motherboard
    wpi: You need to read the LICENSE file in /usr/share/doc/legal/intel_wpi/.
    wpi: If you agree with the license, set legal.intel_wpi.license_ack=1 in /boot/loader.conf.
    module_register_init: MOD_LOAD (wpi_fw, 0xc095c1e0, 0) error 1
    ipw_bss: You need to read the LICENSE file in /usr/share/doc/legal/intel_ipw/.
    ipw_bss: If you agree with the license, set legal.intel_ipw.license_ack=1 in /boot/loader.conf.
    module_register_init: MOD_LOAD (ipw_bss_fw, 0xc0767240, 0) error 1
    ipw_ibss: You need to read the LICENSE file in /usr/share/doc/legal/intel_ipw/.
    ipw_ibss: If you agree with the license, set legal.intel_ipw.license_ack=1 in /boot/loader.conf.
    module_register_init: MOD_LOAD (ipw_ibss_fw, 0xc0767300, 0) error 1
    ipw_monitor: You need to read the LICENSE file in /usr/share/doc/legal/intel_ipw/.
    ipw_monitor: If you agree with the license, set legal.intel_ipw.license_ack=1 in /boot/loader.conf.
    module_register_init: MOD_LOAD (ipw_monitor_fw, 0xc07673c0, 0) error 1
    wlan: mac acl policy registered
    kbd1 at kbdmux0
    cryptosoft0: <software crypto="">on motherboard
    padlock0: No ACE support.
    acpi0: <dell pe_sc3="">on motherboard
    acpi0: [ITHREAD]
    acpi0: Power Button (fixed)
    Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
    acpi_timer0: <24-bit timer at 3.579545MHz> port 0x808-0x80b on acpi0
    cpu0: <acpi cpu="">on acpi0
    cpu1: <acpi cpu="">on acpi0
    cpu2: <acpi cpu="">on acpi0
    cpu3: <acpi cpu="">on acpi0
    acpi_hpet0: <high precision="" event="" timer="">iomem 0xfed00000-0xfed003ff on acpi0
    Timecounter "HPET" frequency 14318180 Hz quality 900
    pcib0: <acpi host-pci="" bridge="">port 0xcf8-0xcff on acpi0
    pci0: <acpi pci="" bus="">on pcib0
    pcib1: <acpi pci-pci="" bridge="">at device 1.0 on pci0
    pci1: <acpi pci="" bus="">on pcib1
    bce0: <broadcom netxtreme="" ii="" bcm5716="" 1000base-t="" (c0)="">mem 0xd8000000-0xd9ffffff irq 36 at device 0.0 on pci1
    miibus0: <mii bus="">on bce0
    brgphy0: <bcm5709c 10="" 100="" 1000basetx="" phy="">PHY 1 on miibus0
    brgphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto
    bce0: [ITHREAD]
    bce0: ASIC (0x57092008); Rev (C0); Bus (PCIe x4, 2.5Gbps); B/C (5.2.3); Flags (MSI|MFW); MFW (NCSI 2.0.11)
    bce1: <broadcom netxtreme="" ii="" bcm5716="" 1000base-t="" (c0)="">mem 0xda000000-0xdbffffff irq 48 at device 0.1 on pci1
    miibus1: <mii bus="">on bce1
    brgphy1: <bcm5709c 10="" 100="" 1000basetx="" phy="">PHY 1 on miibus1
    brgphy1:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto
    bce1: [ITHREAD]
    bce1: ASIC (0x57092008); Rev (C0); Bus (PCIe x4, 2.5Gbps); B/C (5.2.3); Flags (MSI|MFW); MFW (NCSI 2.0.11)
    pcib2: <acpi pci-pci="" bridge="">at device 3.0 on pci0
    pci2: <acpi pci="" bus="">on pcib2
    mpt0: <lsilogic sas="" sata="" adapter="">port 0xfc00-0xfcff mem 0xdeaec000-0xdeaeffff,0xdeaf0000-0xdeafffff irq 32 at device 0.0 on pci2
    mpt0: [ITHREAD]
    mpt0: MPI Version=1.5.18.0
    mpt0: Capabilities: ( RAID-0 RAID-1E RAID-1 )
    mpt0: 1 Active Volume (2 Max)
    mpt0: 2 Hidden Drive Members (14 Max)
    pcib3: <acpi pci-pci="" bridge="">at device 7.0 on pci0
    pci3: <acpi pci="" bus="">on pcib3
    pcib4: <pci-pci bridge="">at device 0.0 on pci3
    pci4: <pci bus="">on pcib4
    pcib5: <pci-pci bridge="">at device 2.0 on pci4
    pci5: <pci bus="">on pcib5
    igb0: <intel(r) 1000="" pro="" network="" connection="" version="" -="" 2.0.7="">port 0xecc0-0xecdf mem 0xddfc0000-0xddfdffff,0xde000000-0xde3fffff,0xddfb8000-0xddfbbfff irq 47 at device 0.0 on pci5
    igb0: Using MSIX interrupts with 5 vectors
    igb0: [ITHREAD]
    igb0: [ITHREAD]
    igb0: [ITHREAD]
    igb0: [ITHREAD]
    igb0: [ITHREAD]
    igb1: <intel(r) 1000="" pro="" network="" connection="" version="" -="" 2.0.7="">port 0xece0-0xecff mem 0xddfe0000-0xddffffff,0xde400000-0xde7fffff,0xddfbc000-0xddfbffff irq 46 at device 0.1 on pci5
    igb1: Using MSIX interrupts with 5 vectors
    igb1: [ITHREAD]
    igb1: [ITHREAD]
    igb1: [ITHREAD]
    igb1: [ITHREAD]
    igb1: [ITHREAD]
    pcib6: <pci-pci bridge="">at device 4.0 on pci4
    pci6: <pci bus="">on pcib6
    igb2: <intel(r) 1000="" pro="" network="" connection="" version="" -="" 2.0.7="">port 0xdcc0-0xdcdf mem 0xdd3c0000-0xdd3dffff,0xdd400000-0xdd7fffff,0xdd3b8000-0xdd3bbfff irq 38 at device 0.0 on pci6
    igb2: Using MSIX interrupts with 5 vectors
    igb2: [ITHREAD]
    igb2: [ITHREAD]
    igb2: [ITHREAD]
    igb2: [ITHREAD]
    igb2: [ITHREAD]
    igb3: <intel(r) 1000="" pro="" network="" connection="" version="" -="" 2.0.7="">port 0xdce0-0xdcff mem 0xdd3e0000-0xdd3fffff,0xdd800000-0xddbfffff,0xdd3bc000-0xdd3bffff irq 45 at device 0.1 on pci6
    igb3: Using MSIX interrupts with 5 vectors
    igb3: [ITHREAD]
    igb3: [ITHREAD]
    igb3: [ITHREAD]
    igb3: [ITHREAD]
    igb3: [ITHREAD]
    pcib7: <acpi pci-pci="" bridge="">at device 9.0 on pci0
    pci7: <acpi pci="" bus="">on pcib7
    pcib8: <acpi pci-pci="" bridge="">at device 10.0 on pci0
    pci8: <acpi pci="" bus="">on pcib8
    pci0: <base peripheral,="" interrupt="" controller=""> at device 20.0 (no driver attached)
    pci0: <base peripheral,="" interrupt="" controller=""> at device 20.1 (no driver attached)
    pci0: <base peripheral,="" interrupt="" controller=""> at device 20.2 (no driver attached)
    uhci0: <intel 82801ji="" (ich10)="" usb="" controller="" usb-d="">port 0xcc40-0xcc5f irq 17 at device 26.0 on pci0
    uhci0: [ITHREAD]
    usbus0: <intel 82801ji="" (ich10)="" usb="" controller="" usb-d="">on uhci0
    uhci1: <intel 82801ji="" (ich10)="" usb="" controller="" usb-e="">port 0xcc60-0xcc7f irq 18 at device 26.1 on pci0
    uhci1: [ITHREAD]
    usbus1: <intel 82801ji="" (ich10)="" usb="" controller="" usb-e="">on uhci1
    ehci0: <intel 82801ji="" (ich10)="" usb="" 2.0="" controller="" usb-b="">mem 0xde8fe000-0xde8fe3ff irq 19 at device 26.7 on pci0
    ehci0: [ITHREAD]
    usbus2: EHCI version 1.0
    usbus2: <intel 82801ji="" (ich10)="" usb="" 2.0="" controller="" usb-b="">on ehci0
    uhci2: <intel 82801ji="" (ich10)="" usb="" controller="" usb-a="">port 0xcc80-0xcc9f irq 21 at device 29.0 on pci0
    uhci2: [ITHREAD]
    usbus3: <intel 82801ji="" (ich10)="" usb="" controller="" usb-a="">on uhci2
    uhci3: <intel 82801ji="" (ich10)="" usb="" controller="" usb-b="">port 0xcca0-0xccbf irq 20 at device 29.1 on pci0
    uhci3: [ITHREAD]
    usbus4: <intel 82801ji="" (ich10)="" usb="" controller="" usb-b="">on uhci3
    uhci4: <intel 82801ji="" (ich10)="" usb="" controller="" usb-c="">port 0xccc0-0xccdf irq 21 at device 29.2 on pci0
    uhci4: [ITHREAD]
    usbus5: <intel 82801ji="" (ich10)="" usb="" controller="" usb-c="">on uhci4
    uhci5: <intel 82801ji="" (ich10)="" usb="" controller="" usb-f="">port 0xcce0-0xccff irq 20 at device 29.3 on pci0
    uhci5: [ITHREAD]
    usbus6: <intel 82801ji="" (ich10)="" usb="" controller="" usb-f="">on uhci5
    ehci1: <intel 82801ji="" (ich10)="" usb="" 2.0="" controller="" usb-a="">mem 0xde8ff000-0xde8ff3ff irq 21 at device 29.7 on pci0
    ehci1: [ITHREAD]
    usbus7: EHCI version 1.0
    usbus7: <intel 82801ji="" (ich10)="" usb="" 2.0="" controller="" usb-a="">on ehci1
    pcib9: <acpi pci-pci="" bridge="">at device 30.0 on pci0
    pci9: <acpi pci="" bus="">on pcib9
    vgapci0: <vga-compatible display="">mem 0xd7800000-0xd7ffffff,0xdc7fc000-0xdc7fffff,0xdc800000-0xdcffffff irq 19 at device 3.0 on pci9
    isab0: <pci-isa bridge="">at device 31.0 on pci0
    isa0: <isa bus="">on isab0
    atapci0: <intel ich10="" sata300="" controller="">port 0xc8e0-0xc8e7,0xc8d0-0xc8d3,0xc8e8-0xc8ef,0xc8d4-0xc8d7,0xcc00-0xcc0f,0xcc10-0xcc1f irq 23 at device 31.2 on pci0
    atapci0: [ITHREAD]
    ata2: <ata 0="" channel="">on atapci0
    ata2: [ITHREAD]
    ata3: <ata 1="" channel="">on atapci0
    ata3: [ITHREAD]
    atapci1: <intel ich10="" sata300="" controller="">port 0xc8f0-0xc8f7,0xc8d8-0xc8db,0xc8f8-0xc8ff,0xc8dc-0xc8df,0xcc20-0xcc2f,0xcc30-0xcc3f irq 22 at device 31.5 on pci0
    atapci1: [ITHREAD]
    ata4: <ata 0="" channel="">on atapci1
    ata4: [ITHREAD]
    ata5: <ata 1="" channel="">on atapci1
    ata5: [ITHREAD]
    atrtc0: <at realtime="" clock="">port 0x70-0x7f irq 8 on acpi0
    uart0: <16550 or compatible> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0
    uart0: [FILTER]
    uart1: <16550 or compatible> port 0x2f8-0x2ff irq 3 on acpi0
    uart1: [FILTER]
    pmtimer0 on isa0
    orm0: <isa option="" roms="">at iomem 0xc0000-0xc7fff,0xce000-0xcefff,0xec000-0xeffff pnpid ORM0000 on isa0
    sc0: <system console="">at flags 0x100 on isa0
    sc0: VGA <16 virtual consoles, flags=0x300>
    vga0: <generic isa="" vga="">at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
    ata0 at port 0x1f0-0x1f7,0x3f6 irq 14 on isa0
    ata0: [ITHREAD]
    ata1 at port 0x170-0x177,0x376 irq 15 on isa0
    ata1: [ITHREAD]
    atkbdc0: <keyboard controller="" (i8042)="">at port 0x60,0x64 on isa0
    atkbd0: <at keyboard="">irq 1 on atkbdc0
    kbd0 at atkbd0
    atkbd0: [GIANT-LOCKED]
    atkbd0: [ITHREAD]
    ppc0: parallel port not found.
    est0: <enhanced speedstep="" frequency="" control="">on cpu0
    est: CPU supports Enhanced Speedstep, but is not recognized.
    est: cpu_vendor GenuineIntel, msr f
    device_attach: est0 attach returned 6
    p4tcc0: <cpu frequency="" thermal="" control="">on cpu0
    est1: <enhanced speedstep="" frequency="" control="">on cpu1
    est: CPU supports Enhanced Speedstep, but is not recognized.
    est: cpu_vendor GenuineIntel, msr f
    device_attach: est1 attach returned 6
    p4tcc1: <cpu frequency="" thermal="" control="">on cpu1
    est2: <enhanced speedstep="" frequency="" control="">on cpu2
    est: CPU supports Enhanced Speedstep, but is not recognized.
    est: cpu_vendor GenuineIntel, msr f
    device_attach: est2 attach returned 6
    p4tcc2: <cpu frequency="" thermal="" control="">on cpu2
    est3: <enhanced speedstep="" frequency="" control="">on cpu3
    est: CPU supports Enhanced Speedstep, but is not recognized.
    est: cpu_vendor GenuineIntel, msr f
    device_attach: est3 attach returned 6
    p4tcc3: <cpu frequency="" thermal="" control="">on cpu3
    Timecounters tick every 1.000 msec
    IPsec: Initialized Security Association Processing.
    usbus0: 12Mbps Full Speed USB v1.0
    usbus1: 12Mbps Full Speed USB v1.0
    usbus2: 480Mbps High Speed USB v2.0
    usbus3: 12Mbps Full Speed USB v1.0
    usbus4: 12Mbps Full Speed USB v1.0
    usbus5: 12Mbps Full Speed USB v1.0
    usbus6: 12Mbps Full Speed USB v1.0
    usbus7: 480Mbps High Speed USB v2.0
    mpt0:vol0(mpt0:0:0): Settings ( Member-WCE Hot-Plug-Spares High-Priority-ReSync )
    mpt0:vol0(mpt0:0:0): Using Spare Pool: 0
    mpt0:vol0(mpt0:0:0): 2 Members:
          (mpt0:1:9:0): Primary Online
          (mpt0:1:1:0): Secondary Online
    mpt0:vol0(mpt0:0:0): RAID-1 - Optimal
    mpt0:vol0(mpt0:0:0): Status ( Enabled )
    (mpt0:vol0:1): Physical (mpt0:0:1:0), Pass-thru (mpt0:1:0:0)
    (mpt0:vol0:1): Online
    (mpt0:vol0:0): Physical (mpt0:0:9:0), Pass-thru (mpt0:1:1:0)
    (mpt0:vol0:0): Online
    (xpt0:mpt0:1👎-1): rescan already queued
    ugen0.1: <intel>at usbus0
    uhub0: <intel 1="" 9="" uhci="" root="" hub,="" class="" 0,="" rev="" 1.00="" 1.00,="" addr="">on usbus0
    ugen1.1: <intel>at usbus1
    uhub1: <intel 1="" 9="" uhci="" root="" hub,="" class="" 0,="" rev="" 1.00="" 1.00,="" addr="">on usbus1
    ugen2.1: <intel>at usbus2
    uhub2: <intel 1="" 9="" ehci="" root="" hub,="" class="" 0,="" rev="" 2.00="" 1.00,="" addr="">on usbus2
    ugen3.1: <intel>at usbus3
    uhub3: <intel 1="" 9="" uhci="" root="" hub,="" class="" 0,="" rev="" 1.00="" 1.00,="" addr="">on usbus3
    ugen4.1: <intel>at usbus4
    uhub4: <intel 1="" 9="" uhci="" root="" hub,="" class="" 0,="" rev="" 1.00="" 1.00,="" addr="">on usbus4
    ugen5.1: <intel>at usbus5
    uhub5: <intel 1="" 9="" uhci="" root="" hub,="" class="" 0,="" rev="" 1.00="" 1.00,="" addr="">on usbus5
    ugen6.1: <intel>at usbus6
    uhub6: <intel 1="" 9="" uhci="" root="" hub,="" class="" 0,="" rev="" 1.00="" 1.00,="" addr="">on usbus6
    ugen7.1: <intel>at usbus7
    uhub7: <intel 1="" 9="" ehci="" root="" hub,="" class="" 0,="" rev="" 2.00="" 1.00,="" addr="">on usbus7
    uhub0: 2 ports with 2 removable, self powered
    uhub1: 2 ports with 2 removable, self powered
    uhub3: 2 ports with 2 removable, self powered
    uhub4: 2 ports with 2 removable, self powered
    uhub5: 2 ports with 2 removable, self powered
    uhub6: 2 ports with 2 removable, self powered
    uhub2: 4 ports with 4 removable, self powered
    uhub7: 4 ports with 4 removable, self powered
    acd0: DVDROM <teac dvd-rom="" dv-28sw="" r.2a="">at ata4-master UDMA100 SATA 1.5Gb/s
    ses0 at mpt0 bus 0 scbus0 target 8 lun 0
    ses0: <dp backplane="" 1.10="">Fixed Enclosure Services SCSI-5 device
    ses0: 300.000MB/s transfers
    ses0: SCSI-3 SES Device
    da0 at mpt0 bus 0 scbus0 target 0 lun 0
    da0: <dell 1028="" virtual="" disk="">Fixed Direct Access SCSI-5 device
    da0: 300.000MB/s transfers
    da0: Command Queueing enabled
    da0: 237824MB (487063552 512 byte sectors: 255H 63S/T 30318C)
    pass2 at mpt0 bus 1 scbus1 target 0 lun 0
    pass2: <ata wdc="" wd2502abys-1="" 3b05="">Fixed Uninstalled SCSI-5 device
    pass2: 300.000MB/s transfers
    pass2: Command Queueing enabled
    SMP: AP CPU #1 Launched!
    SMP: AP CPU #3 Launched!
    SMP: AP CPU #2 Launched!
    Root mount waiting for: usbus2
    ugen2.2: <vendor 0x0424="">at usbus2
    uhub8: <vendor 2="" 9="" 0x0424="" product="" 0x2514,="" class="" 0,="" rev="" 2.00="" 0.00,="" addr="">on usbus2
    ugen0.2: <dell>at usbus0
    ukbd0: <ep1 interrupt="">on usbus0
    kbd2 at ukbd0
    uhub8: 2 ports with 2 removable, self powered
    Trying to mount root from ufs:/dev/da0s1a
    pflog0: promiscuous mode enabled
    bce1: link state changed to UP
    interrupt                          total      rate
    irq17: uhci0                          19          0
    irq19: ehci0                        103          0
    irq22: atapci1                        68          0
    irq32: mpt0                        2244        13
    cpu0: timer                      340586      1980
    irq256: bce0                          1          0
    irq257: bce1                        604          3
    cpu1: timer                      331343      1926
    cpu3: timer                      332203      1931
    cpu2: timer                      332203      1931
    Total                            1339374      7787

    3rd Test

    1 Add-In Quad Port NIC installed
    BIOS Settings set to Default
    Boot to LiveCD and attempt to install
    I see this message go by during the boot for each Intel NIC:  igb#  Could not setup receive structures
    LiveCD hangs at "Starting DHCP Service…"
    Solid cursor at end of the line

    This test was repeated twice with the same results

    4th Test

    BIOS Setting changed to Set CPU to single core
    Everything Works!

    R510 w 1 NIC installed & CPU = Single

    dmesg; vmstat -i
    Copyright © 1992-2010 The FreeBSD Project.
    Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
    The Regents of the University of California. All rights reserved.
    FreeBSD is a registered trademark of The FreeBSD Foundation.
    FreeBSD 8.1-RELEASE-p2 #0: Sat Feb 26 15:29:09 EST 2011
        sullrich@FreeBSD_8.0_pfSense_2.0-snaps.pfsense.org:/usr/obj.pfSense/usr/pfSensesrc/src/sys/pfSense_SMP.8 i386
    Timecounter "i8254" frequency 1193182 Hz quality 0
    CPU: Intel(R) Xeon(R) CPU          E5503  @ 2.00GHz (2000.08-MHz 686-class CPU)
      Origin = "GenuineIntel"  Id = 0x106a5  Family = 6  Model = 1a  Stepping = 5
      Features=0xbfebfbff <fpu,vme,de,pse,tsc,msr,pae,mce,cx8,apic,sep,mtrr,pge,mca,cmov,pat,pse36,clflush,dts,acpi,mmx,fxsr,sse,sse2,ss,htt,tm,pbe>Features2=0x9ce3bd <sse3,dtes64,mon,ds_cpl,vmx,est,tm2,ssse3,cx16,xtpr,pdcm,dca,sse4.1,sse4.2,popcnt>AMD Features=0x28100000 <nx,rdtscp,lm>AMD Features2=0x1 <lahf>TSC: P-state invariant
    real memory  = 2147483648 (2048 MB)
    avail memory = 2069499904 (1973 MB)
    ACPI APIC Table: <dell  pe_sc3 ="">FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs
    FreeBSD/SMP: 2 package(s) x 1 core(s)
    cpu0 (BSP): APIC ID: 16
    cpu1 (AP): APIC ID:  0
    ioapic1: Changing APIC ID to 1
    ioapic0 <version 2.0="">irqs 0-23 on motherboard
    ioapic1 <version 2.0="">irqs 32-55 on motherboard
    wpi: You need to read the LICENSE file in /usr/share/doc/legal/intel_wpi/.
    wpi: If you agree with the license, set legal.intel_wpi.license_ack=1 in /boot/loader.conf.
    module_register_init: MOD_LOAD (wpi_fw, 0xc095c1e0, 0) error 1
    ipw_bss: You need to read the LICENSE file in /usr/share/doc/legal/intel_ipw/.
    ipw_bss: If you agree with the license, set legal.intel_ipw.license_ack=1 in /boot/loader.conf.
    module_register_init: MOD_LOAD (ipw_bss_fw, 0xc0767240, 0) error 1
    ipw_ibss: You need to read the LICENSE file in /usr/share/doc/legal/intel_ipw/.
    ipw_ibss: If you agree with the license, set legal.intel_ipw.license_ack=1 in /boot/loader.conf.
    module_register_init: MOD_LOAD (ipw_ibss_fw, 0xc0767300, 0) error 1
    ipw_monitor: You need to read the LICENSE file in /usr/share/doc/legal/intel_ipw/.
    ipw_monitor: If you agree with the license, set legal.intel_ipw.license_ack=1 in /boot/loader.conf.
    module_register_init: MOD_LOAD (ipw_monitor_fw, 0xc07673c0, 0) error 1
    wlan: mac acl policy registered
    kbd1 at kbdmux0
    cryptosoft0: <software crypto="">on motherboard
    padlock0: No ACE support.
    acpi0: <dell pe_sc3="">on motherboard
    acpi0: [ITHREAD]
    acpi0: Power Button (fixed)
    Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
    acpi_timer0: <24-bit timer at 3.579545MHz> port 0x808-0x80b on acpi0
    cpu0: <acpi cpu="">on acpi0
    cpu1: <acpi cpu="">on acpi0
    acpi_hpet0: <high precision="" event="" timer="">iomem 0xfed00000-0xfed003ff on acpi0
    Timecounter "HPET" frequency 14318180 Hz quality 900
    pcib0: <acpi host-pci="" bridge="">port 0xcf8-0xcff on acpi0
    pci0: <acpi pci="" bus="">on pcib0
    pcib1: <acpi pci-pci="" bridge="">at device 1.0 on pci0
    pci1: <acpi pci="" bus="">on pcib1
    bce0: <broadcom netxtreme="" ii="" bcm5716="" 1000base-t="" (c0)="">mem 0xd8000000-0xd9ffffff irq 36 at device 0.0 on pci1
    miibus0: <mii bus="">on bce0
    brgphy0: <bcm5709c 10="" 100="" 1000basetx="" phy="">PHY 1 on miibus0
    brgphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto
    bce0: [ITHREAD]
    bce0: ASIC (0x57092008); Rev (C0); Bus (PCIe x4, 2.5Gbps); B/C (5.2.3); Flags (MSI|MFW); MFW (NCSI 2.0.11)
    bce1: <broadcom netxtreme="" ii="" bcm5716="" 1000base-t="" (c0)="">mem 0xda000000-0xdbffffff irq 48 at device 0.1 on pci1
    miibus1: <mii bus="">on bce1
    brgphy1: <bcm5709c 10="" 100="" 1000basetx="" phy="">PHY 1 on miibus1
    brgphy1:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto
    bce1: [ITHREAD]
    bce1: ASIC (0x57092008); Rev (C0); Bus (PCIe x4, 2.5Gbps); B/C (5.2.3); Flags (MSI|MFW); MFW (NCSI 2.0.11)
    pcib2: <acpi pci-pci="" bridge="">at device 3.0 on pci0
    pci2: <acpi pci="" bus="">on pcib2
    mpt0: <lsilogic sas="" sata="" adapter="">port 0xfc00-0xfcff mem 0xdeaec000-0xdeaeffff,0xdeaf0000-0xdeafffff irq 32 at device 0.0 on pci2
    mpt0: [ITHREAD]
    mpt0: MPI Version=1.5.18.0
    mpt0: Capabilities: ( RAID-0 RAID-1E RAID-1 )
    mpt0: 1 Active Volume (2 Max)
    mpt0: 2 Hidden Drive Members (14 Max)
    pcib3: <acpi pci-pci="" bridge="">at device 7.0 on pci0
    pci3: <acpi pci="" bus="">on pcib3
    pcib4: <pci-pci bridge="">at device 0.0 on pci3
    pci4: <pci bus="">on pcib4
    pcib5: <pci-pci bridge="">at device 2.0 on pci4
    pci5: <pci bus="">on pcib5
    igb0: <intel(r) 1000="" pro="" network="" connection="" version="" -="" 2.0.7="">port 0xecc0-0xecdf mem 0xddfc0000-0xddfdffff,0xde000000-0xde3fffff,0xddfb8000-0xddfbbfff irq 47 at device 0.0 on pci5
    igb0: Using MSIX interrupts with 3 vectors
    igb0: [ITHREAD]
    igb0: [ITHREAD]
    igb0: [ITHREAD]
    igb1: <intel(r) 1000="" pro="" network="" connection="" version="" -="" 2.0.7="">port 0xece0-0xecff mem 0xddfe0000-0xddffffff,0xde400000-0xde7fffff,0xddfbc000-0xddfbffff irq 46 at device 0.1 on pci5
    igb1: Using MSIX interrupts with 3 vectors
    igb1: [ITHREAD]
    igb1: [ITHREAD]
    igb1: [ITHREAD]
    pcib6: <pci-pci bridge="">at device 4.0 on pci4
    pci6: <pci bus="">on pcib6
    igb2: <intel(r) 1000="" pro="" network="" connection="" version="" -="" 2.0.7="">port 0xdcc0-0xdcdf mem 0xdd3c0000-0xdd3dffff,0xdd400000-0xdd7fffff,0xdd3b8000-0xdd3bbfff irq 38 at device 0.0 on pci6
    igb2: Using MSIX interrupts with 3 vectors
    igb2: [ITHREAD]
    igb2: [ITHREAD]
    igb2: [ITHREAD]
    igb3: <intel(r) 1000="" pro="" network="" connection="" version="" -="" 2.0.7="">port 0xdce0-0xdcff mem 0xdd3e0000-0xdd3fffff,0xdd800000-0xddbfffff,0xdd3bc000-0xdd3bffff irq 45 at device 0.1 on pci6
    igb3: Using MSIX interrupts with 3 vectors
    igb3: [ITHREAD]
    igb3: [ITHREAD]
    igb3: [ITHREAD]
    pcib7: <acpi pci-pci="" bridge="">at device 9.0 on pci0
    pci7: <acpi pci="" bus="">on pcib7
    pcib8: <acpi pci-pci="" bridge="">at device 10.0 on pci0
    pci8: <acpi pci="" bus="">on pcib8
    pci0: <base peripheral,="" interrupt="" controller=""> at device 20.0 (no driver attached)
    pci0: <base peripheral,="" interrupt="" controller=""> at device 20.1 (no driver attached)
    pci0: <base peripheral,="" interrupt="" controller=""> at device 20.2 (no driver attached)
    uhci0: <intel 82801ji="" (ich10)="" usb="" controller="" usb-d="">port 0xcc40-0xcc5f irq 17 at device 26.0 on pci0
    uhci0: [ITHREAD]
    usbus0: <intel 82801ji="" (ich10)="" usb="" controller="" usb-d="">on uhci0
    uhci1: <intel 82801ji="" (ich10)="" usb="" controller="" usb-e="">port 0xcc60-0xcc7f irq 18 at device 26.1 on pci0
    uhci1: [ITHREAD]
    usbus1: <intel 82801ji="" (ich10)="" usb="" controller="" usb-e="">on uhci1
    ehci0: <intel 82801ji="" (ich10)="" usb="" 2.0="" controller="" usb-b="">mem 0xde8fe000-0xde8fe3ff irq 19 at device 26.7 on pci0
    ehci0: [ITHREAD]
    usbus2: EHCI version 1.0
    usbus2: <intel 82801ji="" (ich10)="" usb="" 2.0="" controller="" usb-b="">on ehci0
    uhci2: <intel 82801ji="" (ich10)="" usb="" controller="" usb-a="">port 0xcc80-0xcc9f irq 21 at device 29.0 on pci0
    uhci2: [ITHREAD]
    usbus3: <intel 82801ji="" (ich10)="" usb="" controller="" usb-a="">on uhci2
    uhci3: <intel 82801ji="" (ich10)="" usb="" controller="" usb-b="">port 0xcca0-0xccbf irq 20 at device 29.1 on pci0
    uhci3: [ITHREAD]
    usbus4: <intel 82801ji="" (ich10)="" usb="" controller="" usb-b="">on uhci3
    uhci4: <intel 82801ji="" (ich10)="" usb="" controller="" usb-c="">port 0xccc0-0xccdf irq 21 at device 29.2 on pci0
    uhci4: [ITHREAD]
    usbus5: <intel 82801ji="" (ich10)="" usb="" controller="" usb-c="">on uhci4
    uhci5: <intel 82801ji="" (ich10)="" usb="" controller="" usb-f="">port 0xcce0-0xccff irq 20 at device 29.3 on pci0
    uhci5: [ITHREAD]
    usbus6: <intel 82801ji="" (ich10)="" usb="" controller="" usb-f="">on uhci5
    ehci1: <intel 82801ji="" (ich10)="" usb="" 2.0="" controller="" usb-a="">mem 0xde8ff000-0xde8ff3ff irq 21 at device 29.7 on pci0
    ehci1: [ITHREAD]
    usbus7: EHCI version 1.0
    usbus7: <intel 82801ji="" (ich10)="" usb="" 2.0="" controller="" usb-a="">on ehci1
    pcib9: <acpi pci-pci="" bridge="">at device 30.0 on pci0
    pci9: <acpi pci="" bus="">on pcib9
    vgapci0: <vga-compatible display="">mem 0xd7800000-0xd7ffffff,0xdc7fc000-0xdc7fffff,0xdc800000-0xdcffffff irq 19 at device 3.0 on pci9
    isab0: <pci-isa bridge="">at device 31.0 on pci0
    isa0: <isa bus="">on isab0
    atapci0: <intel ich10="" sata300="" controller="">port 0xc8e0-0xc8e7,0xc8d0-0xc8d3,0xc8e8-0xc8ef,0xc8d4-0xc8d7,0xcc00-0xcc0f,0xcc10-0xcc1f irq 23 at device 31.2 on pci0
    atapci0: [ITHREAD]
    ata2: <ata 0="" channel="">on atapci0
    ata2: [ITHREAD]
    ata3: <ata 1="" channel="">on atapci0
    ata3: [ITHREAD]
    atapci1: <intel ich10="" sata300="" controller="">port 0xc8f0-0xc8f7,0xc8d8-0xc8db,0xc8f8-0xc8ff,0xc8dc-0xc8df,0xcc20-0xcc2f,0xcc30-0xcc3f irq 22 at device 31.5 on pci0
    atapci1: [ITHREAD]
    ata4: <ata 0="" channel="">on atapci1
    ata4: [ITHREAD]
    ata5: <ata 1="" channel="">on atapci1
    ata5: [ITHREAD]
    atrtc0: <at realtime="" clock="">port 0x70-0x7f irq 8 on acpi0
    uart0: <16550 or compatible> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0
    uart0: [FILTER]
    uart1: <16550 or compatible> port 0x2f8-0x2ff irq 3 on acpi0
    uart1: [FILTER]
    pmtimer0 on isa0
    orm0: <isa option="" roms="">at iomem 0xc0000-0xc7fff,0xce000-0xcefff,0xec000-0xeffff pnpid ORM0000 on isa0
    sc0: <system console="">at flags 0x100 on isa0
    sc0: VGA <16 virtual consoles, flags=0x300>
    vga0: <generic isa="" vga="">at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
    ata0 at port 0x1f0-0x1f7,0x3f6 irq 14 on isa0
    ata0: [ITHREAD]
    ata1 at port 0x170-0x177,0x376 irq 15 on isa0
    ata1: [ITHREAD]
    atkbdc0: <keyboard controller="" (i8042)="">at port 0x60,0x64 on isa0
    atkbd0: <at keyboard="">irq 1 on atkbdc0
    kbd0 at atkbd0
    atkbd0: [GIANT-LOCKED]
    atkbd0: [ITHREAD]
    ppc0: parallel port not found.
    est0: <enhanced speedstep="" frequency="" control="">on cpu0
    est: CPU supports Enhanced Speedstep, but is not recognized.
    est: cpu_vendor GenuineIntel, msr f
    device_attach: est0 attach returned 6
    p4tcc0: <cpu frequency="" thermal="" control="">on cpu0
    est1: <enhanced speedstep="" frequency="" control="">on cpu1
    est: CPU supports Enhanced Speedstep, but is not recognized.
    est: cpu_vendor GenuineIntel, msr f
    device_attach: est1 attach returned 6
    p4tcc1: <cpu frequency="" thermal="" control="">on cpu1
    Timecounters tick every 1.000 msec
    IPsec: Initialized Security Association Processing.
    usbus0: 12Mbps Full Speed USB v1.0
    usbus1: 12Mbps Full Speed USB v1.0
    usbus2: 480Mbps High Speed USB v2.0
    usbus3: 12Mbps Full Speed USB v1.0
    usbus4: 12Mbps Full Speed USB v1.0
    usbus5: 12Mbps Full Speed USB v1.0
    usbus6: 12Mbps Full Speed USB v1.0
    usbus7: 480Mbps High Speed USB v2.0
    mpt0:vol0(mpt0:0:0): Settings ( Member-WCE Hot-Plug-Spares High-Priority-ReSync )
    mpt0:vol0(mpt0:0:0): Using Spare Pool: 0
    mpt0:vol0(mpt0:0:0): 2 Members:
          (mpt0:1:9:0): Primary Online
          (mpt0:1:1:0): Secondary Online
    mpt0:vol0(mpt0:0:0): RAID-1 - Optimal
    mpt0:vol0(mpt0:0:0): Status ( Enabled )
    (mpt0:vol0:1): Physical (mpt0:0:1:0), Pass-thru (mpt0:1:0:0)
    (mpt0:vol0:1): Online
    (mpt0:vol0:0): Physical (mpt0:0:9:0), Pass-thru (mpt0:1:1:0)
    (mpt0:vol0:0): Online
    (xpt0:mpt0:1👎-1): rescan already queued
    ugen0.1: <intel>at usbus0
    uhub0: <intel 1="" 9="" uhci="" root="" hub,="" class="" 0,="" rev="" 1.00="" 1.00,="" addr="">on usbus0
    ugen1.1: <intel>at usbus1
    uhub1: <intel 1="" 9="" uhci="" root="" hub,="" class="" 0,="" rev="" 1.00="" 1.00,="" addr="">on usbus1
    ugen2.1: <intel>at usbus2
    uhub2: <intel 1="" 9="" ehci="" root="" hub,="" class="" 0,="" rev="" 2.00="" 1.00,="" addr="">on usbus2
    ugen3.1: <intel>at usbus3
    uhub3: <intel 1="" 9="" uhci="" root="" hub,="" class="" 0,="" rev="" 1.00="" 1.00,="" addr="">on usbus3
    ugen4.1: <intel>at usbus4
    uhub4: <intel 1="" 9="" uhci="" root="" hub,="" class="" 0,="" rev="" 1.00="" 1.00,="" addr="">on usbus4
    ugen5.1: <intel>at usbus5
    uhub5: <intel 1="" 9="" uhci="" root="" hub,="" class="" 0,="" rev="" 1.00="" 1.00,="" addr="">on usbus5
    ugen6.1: <intel>at usbus6
    uhub6: <intel 1="" 9="" uhci="" root="" hub,="" class="" 0,="" rev="" 1.00="" 1.00,="" addr="">on usbus6
    ugen7.1: <intel>at usbus7
    uhub7: <intel 1="" 9="" ehci="" root="" hub,="" class="" 0,="" rev="" 2.00="" 1.00,="" addr="">on usbus7
    uhub0: 2 ports with 2 removable, self powered
    uhub1: 2 ports with 2 removable, self powered
    uhub3: 2 ports with 2 removable, self powered
    uhub4: 2 ports with 2 removable, self powered
    uhub5: 2 ports with 2 removable, self powered
    uhub6: 2 ports with 2 removable, self powered
    uhub2: 4 ports with 4 removable, self powered
    uhub7: 4 ports with 4 removable, self powered
    acd0: DVDROM <teac dvd-rom="" dv-28sw="" r.2a="">at ata4-master UDMA100 SATA 1.5Gb/s
    ses0 at mpt0 bus 0 scbus0 target 8 lun 0
    ses0: <dp backplane="" 1.10="">Fixed Enclosure Services SCSI-5 device
    ses0: 300.000MB/s transfers
    ses0: SCSI-3 SES Device
    da0 at mpt0 bus 0 scbus0 target 0 lun 0
    da0: <dell 1028="" virtual="" disk="">Fixed Direct Access SCSI-5 device
    da0: 300.000MB/s transfers
    da0: Command Queueing enabled
    da0: 237824MB (487063552 512 byte sectors: 255H 63S/T 30318C)
    pass2 at mpt0 bus 1 scbus1 target 0 lun 0
    pass2: <ata wdc="" wd2502abys-1="" 3b05="">Fixed Uninstalled SCSI-5 device
    pass2: 300.000MB/s transfers
    pass2: Command Queueing enabled
    SMP: AP CPU #1 Launched!
    Root mount waiting for: usbus2
    ugen2.2: <vendor 0x0424="">at usbus2
    uhub8: <vendor 2="" 9="" 0x0424="" product="" 0x2514,="" class="" 0,="" rev="" 2.00="" 0.00,="" addr="">on usbus2
    ugen0.2: <dell>at usbus0
    ukbd0: <ep1 interrupt="">on usbus0
    kbd2 at ukbd0
    Root mount waiting for: usbus2
    uhub8: 4 ports with 4 removable, self powered
    Trying to mount root from ufs:/dev/da0s1a
    pflog0: promiscuous mode enabled
    bce1: link state changed to UP
    igb0: link state changed to UP
    igb1: link state changed to UP
    igb1: link state changed to DOWN
    igb0: link state changed to DOWN
    igb1: link state changed to UP
    igb0: link state changed to UP
    interrupt                          total      rate
    irq17: uhci0                          70          0
    irq19: ehci0                        827          1
    irq22: atapci1                        68          0
    irq32: mpt0                        3087          3
    cpu0: timer                      1603346      1991
    irq256: bce0                          1          0
    irq257: bce1                        492          0
    irq258: igb0:que 0                    20          0
    irq260: igb0:link                      2          0
    irq261: igb1:que 0                    20          0
    irq263: igb1:link                      2          0
    cpu1: timer                      1590708      1976
    Total                            3198643      3973

    5th Test

    Install 2nd Add-in Quad Port NIC to already installed pfSense
    Assign Interfaces
    Everything Works!

    R510 With both NICs installed, CPU = Single

    $ dmesg; vmstat -i
    Copyright © 1992-2010 The FreeBSD Project.
    Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
    The Regents of the University of California. All rights reserved.
    FreeBSD is a registered trademark of The FreeBSD Foundation.
    FreeBSD 8.1-RELEASE-p2 #0: Sat Feb 26 15:29:09 EST 2011
        sullrich@FreeBSD_8.0_pfSense_2.0-snaps.pfsense.org:/usr/obj.pfSense/usr/pfSensesrc/src/sys/pfSense_SMP.8 i386
    Timecounter "i8254" frequency 1193182 Hz quality 0
    CPU: Intel(R) Xeon(R) CPU          E5503  @ 2.00GHz (2000.08-MHz 686-class CPU)
      Origin = "GenuineIntel"  Id = 0x106a5  Family = 6  Model = 1a  Stepping = 5
      Features=0xbfebfbff <fpu,vme,de,pse,tsc,msr,pae,mce,cx8,apic,sep,mtrr,pge,mca,cmov,pat,pse36,clflush,dts,acpi,mmx,fxsr,sse,sse2,ss,htt,tm,pbe>Features2=0x9ce3bd <sse3,dtes64,mon,ds_cpl,vmx,est,tm2,ssse3,cx16,xtpr,pdcm,dca,sse4.1,sse4.2,popcnt>AMD Features=0x28100000 <nx,rdtscp,lm>AMD Features2=0x1 <lahf>TSC: P-state invariant
    real memory  = 2147483648 (2048 MB)
    avail memory = 2069499904 (1973 MB)
    ACPI APIC Table: <dell  pe_sc3 ="">FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs
    FreeBSD/SMP: 2 package(s) x 1 core(s)
    cpu0 (BSP): APIC ID: 16
    cpu1 (AP): APIC ID:  0
    ioapic1: Changing APIC ID to 1
    ioapic0 <version 2.0="">irqs 0-23 on motherboard
    ioapic1 <version 2.0="">irqs 32-55 on motherboard
    wpi: You need to read the LICENSE file in /usr/share/doc/legal/intel_wpi/.
    wpi: If you agree with the license, set legal.intel_wpi.license_ack=1 in /boot/loader.conf.
    module_register_init: MOD_LOAD (wpi_fw, 0xc095c1e0, 0) error 1
    ipw_bss: You need to read the LICENSE file in /usr/share/doc/legal/intel_ipw/.
    ipw_bss: If you agree with the license, set legal.intel_ipw.license_ack=1 in /boot/loader.conf.
    module_register_init: MOD_LOAD (ipw_bss_fw, 0xc0767240, 0) error 1
    ipw_ibss: You need to read the LICENSE file in /usr/share/doc/legal/intel_ipw/.
    ipw_ibss: If you agree with the license, set legal.intel_ipw.license_ack=1 in /boot/loader.conf.
    module_register_init: MOD_LOAD (ipw_ibss_fw, 0xc0767300, 0) error 1
    ipw_monitor: You need to read the LICENSE file in /usr/share/doc/legal/intel_ipw/.
    ipw_monitor: If you agree with the license, set legal.intel_ipw.license_ack=1 in /boot/loader.conf.
    module_register_init: MOD_LOAD (ipw_monitor_fw, 0xc07673c0, 0) error 1
    wlan: mac acl policy registered
    kbd1 at kbdmux0
    cryptosoft0: <software crypto="">on motherboard
    padlock0: No ACE support.
    acpi0: <dell pe_sc3="">on motherboard
    acpi0: [ITHREAD]
    acpi0: Power Button (fixed)
    Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
    acpi_timer0: <24-bit timer at 3.579545MHz> port 0x808-0x80b on acpi0
    cpu0: <acpi cpu="">on acpi0
    cpu1: <acpi cpu="">on acpi0
    acpi_hpet0: <high precision="" event="" timer="">iomem 0xfed00000-0xfed003ff on acpi0
    Timecounter "HPET" frequency 14318180 Hz quality 900
    pcib0: <acpi host-pci="" bridge="">port 0xcf8-0xcff on acpi0
    pci0: <acpi pci="" bus="">on pcib0
    pcib1: <acpi pci-pci="" bridge="">at device 1.0 on pci0
    pci1: <acpi pci="" bus="">on pcib1
    bce0: <broadcom netxtreme="" ii="" bcm5716="" 1000base-t="" (c0)="">mem 0xd6000000-0xd7ffffff irq 36 at device 0.0 on pci1
    miibus0: <mii bus="">on bce0
    brgphy0: <bcm5709c 10="" 100="" 1000basetx="" phy="">PHY 1 on miibus0
    brgphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto
    bce0: [ITHREAD]
    bce0: ASIC (0x57092008); Rev (C0); Bus (PCIe x4, 2.5Gbps); B/C (5.2.3); Flags (MSI|MFW); MFW (NCSI 2.0.11)
    bce1: <broadcom netxtreme="" ii="" bcm5716="" 1000base-t="" (c0)="">mem 0xd8000000-0xd9ffffff irq 48 at device 0.1 on pci1
    miibus1: <mii bus="">on bce1
    brgphy1: <bcm5709c 10="" 100="" 1000basetx="" phy="">PHY 1 on miibus1
    brgphy1:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto
    bce1: [ITHREAD]
    bce1: ASIC (0x57092008); Rev (C0); Bus (PCIe x4, 2.5Gbps); B/C (5.2.3); Flags (MSI|MFW); MFW (NCSI 2.0.11)
    pcib2: <acpi pci-pci="" bridge="">at device 3.0 on pci0
    pci2: <acpi pci="" bus="">on pcib2
    mpt0: <lsilogic sas="" sata="" adapter="">port 0xfc00-0xfcff mem 0xde2ec000-0xde2effff,0xde2f0000-0xde2fffff irq 32 at device 0.0 on pci2
    mpt0: [ITHREAD]
    mpt0: MPI Version=1.5.18.0
    mpt0: Capabilities: ( RAID-0 RAID-1E RAID-1 )
    mpt0: 1 Active Volume (2 Max)
    mpt0: 2 Hidden Drive Members (14 Max)
    pcib3: <acpi pci-pci="" bridge="">at device 7.0 on pci0
    pci3: <acpi pci="" bus="">on pcib3
    pcib4: <pci-pci bridge="">at device 0.0 on pci3
    pci4: <pci bus="">on pcib4
    pcib5: <pci-pci bridge="">at device 2.0 on pci4
    pci5: <pci bus="">on pcib5
    igb0: <intel(r) 1000="" pro="" network="" connection="" version="" -="" 2.0.7="">port 0xecc0-0xecdf mem 0xdbfc0000-0xdbfdffff,0xdc000000-0xdc3fffff,0xdbfb8000-0xdbfbbfff irq 47 at device 0.0 on pci5
    igb0: Using MSIX interrupts with 3 vectors
    igb0: [ITHREAD]
    igb0: [ITHREAD]
    igb0: [ITHREAD]
    igb1: <intel(r) 1000="" pro="" network="" connection="" version="" -="" 2.0.7="">port 0xece0-0xecff mem 0xdbfe0000-0xdbffffff,0xdc400000-0xdc7fffff,0xdbfbc000-0xdbfbffff irq 46 at device 0.1 on pci5
    igb1: Using MSIX interrupts with 3 vectors
    igb1: [ITHREAD]
    igb1: [ITHREAD]
    igb1: [ITHREAD]
    pcib6: <pci-pci bridge="">at device 4.0 on pci4
    pci6: <pci bus="">on pcib6
    igb2: <intel(r) 1000="" pro="" network="" connection="" version="" -="" 2.0.7="">port 0xdcc0-0xdcdf mem 0xdb3c0000-0xdb3dffff,0xdb400000-0xdb7fffff,0xdb3b8000-0xdb3bbfff irq 38 at device 0.0 on pci6
    igb2: Using MSIX interrupts with 3 vectors
    igb2: [ITHREAD]
    igb2: [ITHREAD]
    igb2: [ITHREAD]
    igb3: <intel(r) 1000="" pro="" network="" connection="" version="" -="" 2.0.7="">port 0xdce0-0xdcff mem 0xdb3e0000-0xdb3fffff,0xdb800000-0xdbbfffff,0xdb3bc000-0xdb3bffff irq 45 at device 0.1 on pci6
    igb3: Using MSIX interrupts with 3 vectors
    igb3: [ITHREAD]
    igb3: [ITHREAD]
    igb3: [ITHREAD]
    pcib7: <acpi pci-pci="" bridge="">at device 9.0 on pci0
    pci7: <acpi pci="" bus="">on pcib7
    pcib8: <pci-pci bridge="">at device 0.0 on pci7
    pci8: <pci bus="">on pcib8
    pcib9: <pci-pci bridge="">at device 2.0 on pci8
    pci9: <pci bus="">on pcib9
    igb4: <intel(r) 1000="" pro="" network="" connection="" version="" -="" 2.0.7="">port 0xccc0-0xccdf mem 0xdd7c0000-0xdd7dffff,0xdd800000-0xddbfffff,0xdd7b8000-0xdd7bbfff irq 55 at device 0.0 on pci9
    igb4: Using MSIX interrupts with 3 vectors
    igb4: [ITHREAD]
    igb4: [ITHREAD]
    igb4: [ITHREAD]
    igb5: <intel(r) 1000="" pro="" network="" connection="" version="" -="" 2.0.7="">port 0xcce0-0xccff mem 0xdd7e0000-0xdd7fffff,0xddc00000-0xddffffff,0xdd7bc000-0xdd7bffff irq 49 at device 0.1 on pci9
    igb5: Using MSIX interrupts with 3 vectors
    igb5: [ITHREAD]
    igb5: [ITHREAD]
    igb5: [ITHREAD]
    pcib10: <pci-pci bridge="">at device 4.0 on pci8
    pci10: <pci bus="">on pcib10
    igb6: <intel(r) 1000="" pro="" network="" connection="" version="" -="" 2.0.7="">port 0xbcc0-0xbcdf mem 0xdcbc0000-0xdcbdffff,0xdcc00000-0xdcffffff,0xdcbb8000-0xdcbbbfff irq 40 at device 0.0 on pci10
    igb6: Using MSIX interrupts with 3 vectors
    igb6: [ITHREAD]
    igb6: [ITHREAD]
    igb6: [ITHREAD]
    igb7: <intel(r) 1000="" pro="" network="" connection="" version="" -="" 2.0.7="">port 0xbce0-0xbcff mem 0xdcbe0000-0xdcbfffff,0xdd000000-0xdd3fffff,0xdcbbc000-0xdcbbffff irq 50 at device 0.1 on pci10
    igb7: Using MSIX interrupts with 3 vectors
    igb7: [ITHREAD]
    igb7: [ITHREAD]
    igb7: [ITHREAD]
    pcib11: <acpi pci-pci="" bridge="">at device 10.0 on pci0
    pci11: <acpi pci="" bus="">on pcib11
    pci0: <base peripheral,="" interrupt="" controller=""> at device 20.0 (no driver attached)
    pci0: <base peripheral,="" interrupt="" controller=""> at device 20.1 (no driver attached)
    pci0: <base peripheral,="" interrupt="" controller=""> at device 20.2 (no driver attached)
    uhci0: <intel 82801ji="" (ich10)="" usb="" controller="" usb-d="">port 0xac40-0xac5f irq 17 at device 26.0 on pci0
    uhci0: [ITHREAD]
    usbus0: <intel 82801ji="" (ich10)="" usb="" controller="" usb-d="">on uhci0
    uhci1: <intel 82801ji="" (ich10)="" usb="" controller="" usb-e="">port 0xac60-0xac7f irq 18 at device 26.1 on pci0
    uhci1: [ITHREAD]
    usbus1: <intel 82801ji="" (ich10)="" usb="" controller="" usb-e="">on uhci1
    ehci0: <intel 82801ji="" (ich10)="" usb="" 2.0="" controller="" usb-b="">mem 0xde0fe000-0xde0fe3ff irq 19 at device 26.7 on pci0
    ehci0: [ITHREAD]
    usbus2: EHCI version 1.0
    usbus2: <intel 82801ji="" (ich10)="" usb="" 2.0="" controller="" usb-b="">on ehci0
    uhci2: <intel 82801ji="" (ich10)="" usb="" controller="" usb-a="">port 0xac80-0xac9f irq 21 at device 29.0 on pci0
    uhci2: [ITHREAD]
    usbus3: <intel 82801ji="" (ich10)="" usb="" controller="" usb-a="">on uhci2
    uhci3: <intel 82801ji="" (ich10)="" usb="" controller="" usb-b="">port 0xaca0-0xacbf irq 20 at device 29.1 on pci0
    uhci3: [ITHREAD]
    usbus4: <intel 82801ji="" (ich10)="" usb="" controller="" usb-b="">on uhci3
    uhci4: <intel 82801ji="" (ich10)="" usb="" controller="" usb-c="">port 0xacc0-0xacdf irq 21 at device 29.2 on pci0
    uhci4: [ITHREAD]
    usbus5: <intel 82801ji="" (ich10)="" usb="" controller="" usb-c="">on uhci4
    uhci5: <intel 82801ji="" (ich10)="" usb="" controller="" usb-f="">port 0xace0-0xacff irq 20 at device 29.3 on pci0
    uhci5: [ITHREAD]
    usbus6: <intel 82801ji="" (ich10)="" usb="" controller="" usb-f="">on uhci5
    ehci1: <intel 82801ji="" (ich10)="" usb="" 2.0="" controller="" usb-a="">mem 0xde0ff000-0xde0ff3ff irq 21 at device 29.7 on pci0
    ehci1: [ITHREAD]
    usbus7: EHCI version 1.0
    usbus7: <intel 82801ji="" (ich10)="" usb="" 2.0="" controller="" usb-a="">on ehci1
    pcib12: <acpi pci-pci="" bridge="">at device 30.0 on pci0
    pci12: <acpi pci="" bus="">on pcib12
    vgapci0: <vga-compatible display="">mem 0xd5800000-0xd5ffffff,0xda7fc000-0xda7fffff,0xda800000-0xdaffffff irq 19 at device 3.0 on pci12
    isab0: <pci-isa bridge="">at device 31.0 on pci0
    isa0: <isa bus="">on isab0
    atapci0: <intel ich10="" sata300="" controller="">port 0xa8e0-0xa8e7,0xa8d0-0xa8d3,0xa8e8-0xa8ef,0xa8d4-0xa8d7,0xac00-0xac0f,0xac10-0xac1f irq 23 at device 31.2 on pci0
    atapci0: [ITHREAD]
    ata2: <ata 0="" channel="">on atapci0
    ata2: [ITHREAD]
    ata3: <ata 1="" channel="">on atapci0
    ata3: [ITHREAD]
    atapci1: <intel ich10="" sata300="" controller="">port 0xa8f0-0xa8f7,0xa8d8-0xa8db,0xa8f8-0xa8ff,0xa8dc-0xa8df,0xac20-0xac2f,0xac30-0xac3f irq 22 at device 31.5 on pci0
    atapci1: [ITHREAD]
    ata4: <ata 0="" channel="">on atapci1
    ata4: [ITHREAD]
    ata5: <ata 1="" channel="">on atapci1
    ata5: [ITHREAD]
    atrtc0: <at realtime="" clock="">port 0x70-0x7f irq 8 on acpi0
    uart0: <16550 or compatible> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0
    uart0: [FILTER]
    uart1: <16550 or compatible> port 0x2f8-0x2ff irq 3 on acpi0
    uart1: [FILTER]
    pmtimer0 on isa0
    orm0: <isa option="" roms="">at iomem 0xc0000-0xc7fff,0xce000-0xcefff,0xec000-0xeffff pnpid ORM0000 on isa0
    sc0: <system console="">at flags 0x100 on isa0
    sc0: VGA <16 virtual consoles, flags=0x300>
    vga0: <generic isa="" vga="">at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
    ata0 at port 0x1f0-0x1f7,0x3f6 irq 14 on isa0
    ata0: [ITHREAD]
    ata1 at port 0x170-0x177,0x376 irq 15 on isa0
    ata1: [ITHREAD]
    atkbdc0: <keyboard controller="" (i8042)="">at port 0x60,0x64 on isa0
    atkbd0: <at keyboard="">irq 1 on atkbdc0
    kbd0 at atkbd0
    atkbd0: [GIANT-LOCKED]
    atkbd0: [ITHREAD]
    ppc0: parallel port not found.
    est0: <enhanced speedstep="" frequency="" control="">on cpu0
    est: CPU supports Enhanced Speedstep, but is not recognized.
    est: cpu_vendor GenuineIntel, msr f
    device_attach: est0 attach returned 6
    p4tcc0: <cpu frequency="" thermal="" control="">on cpu0
    est1: <enhanced speedstep="" frequency="" control="">on cpu1
    est: CPU supports Enhanced Speedstep, but is not recognized.
    est: cpu_vendor GenuineIntel, msr f
    device_attach: est1 attach returned 6
    p4tcc1: <cpu frequency="" thermal="" control="">on cpu1
    Timecounters tick every 1.000 msec
    IPsec: Initialized Security Association Processing.
    usbus0: 12Mbps Full Speed USB v1.0
    usbus1: 12Mbps Full Speed USB v1.0
    usbus2: 480Mbps High Speed USB v2.0
    usbus3: 12Mbps Full Speed USB v1.0
    usbus4: 12Mbps Full Speed USB v1.0
    usbus5: 12Mbps Full Speed USB v1.0
    usbus6: 12Mbps Full Speed USB v1.0
    usbus7: 480Mbps High Speed USB v2.0
    mpt0:vol0(mpt0:0:0): Settings ( Member-WCE Hot-Plug-Spares High-Priority-ReSync )
    mpt0:vol0(mpt0:0:0): Using Spare Pool: 0
    mpt0:vol0(mpt0:0:0): 2 Members:
          (mpt0:1:9:0): Primary Online
          (mpt0:1:1:0): Secondary Online
    mpt0:vol0(mpt0:0:0): RAID-1 - Optimal
    mpt0:vol0(mpt0:0:0): Status ( Enabled )
    (mpt0:vol0:1): Physical (mpt0:0:1:0), Pass-thru (mpt0:1:0:0)
    (mpt0:vol0:1): Online
    (mpt0:vol0:0): Physical (mpt0:0:9:0), Pass-thru (mpt0:1:1:0)
    (mpt0:vol0:0): Online
    (xpt0:mpt0:1👎-1): rescan already queued
    ugen0.1: <intel>at usbus0
    uhub0: <intel 1="" 9="" uhci="" root="" hub,="" class="" 0,="" rev="" 1.00="" 1.00,="" addr="">on usbus0
    ugen1.1: <intel>at usbus1
    uhub1: <intel 1="" 9="" uhci="" root="" hub,="" class="" 0,="" rev="" 1.00="" 1.00,="" addr="">on usbus1
    ugen2.1: <intel>at usbus2
    uhub2: <intel 1="" 9="" ehci="" root="" hub,="" class="" 0,="" rev="" 2.00="" 1.00,="" addr="">on usbus2
    ugen3.1: <intel>at usbus3
    uhub3: <intel 1="" 9="" uhci="" root="" hub,="" class="" 0,="" rev="" 1.00="" 1.00,="" addr="">on usbus3
    ugen4.1: <intel>at usbus4
    uhub4: <intel 1="" 9="" uhci="" root="" hub,="" class="" 0,="" rev="" 1.00="" 1.00,="" addr="">on usbus4
    ugen5.1: <intel>at usbus5
    uhub5: <intel 1="" 9="" uhci="" root="" hub,="" class="" 0,="" rev="" 1.00="" 1.00,="" addr="">on usbus5
    ugen6.1: <intel>at usbus6
    uhub6: <intel 1="" 9="" uhci="" root="" hub,="" class="" 0,="" rev="" 1.00="" 1.00,="" addr="">on usbus6
    ugen7.1: <intel>at usbus7
    uhub7: <intel 1="" 9="" ehci="" root="" hub,="" class="" 0,="" rev="" 2.00="" 1.00,="" addr="">on usbus7
    uhub0: 2 ports with 2 removable, self powered
    uhub1: 2 ports with 2 removable, self powered
    uhub3: 2 ports with 2 removable, self powered
    uhub4: 2 ports with 2 removable, self powered
    uhub5: 2 ports with 2 removable, self powered
    uhub6: 2 ports with 2 removable, self powered
    uhub2: 4 ports with 4 removable, self powered
    uhub7: 4 ports with 4 removable, self powered
    acd0: DVDROM <teac dvd-rom="" dv-28sw="" r.2a="">at ata4-master UDMA100 SATA 1.5Gb/s
    ses0 at mpt0 bus 0 scbus0 target 8 lun 0
    ses0: <dp backplane="" 1.10="">Fixed Enclosure Services SCSI-5 device
    ses0: 300.000MB/s transfers
    ses0: SCSI-3 SES Device
    da0 at mpt0 bus 0 scbus0 target 0 lun 0
    da0: <dell 1028="" virtual="" disk="">Fixed Direct Access SCSI-5 device
    da0: 300.000MB/s transfers
    da0: Command Queueing enabled
    da0: 237824MB (487063552 512 byte sectors: 255H 63S/T 30318C)
    pass2 at mpt0 bus 1 scbus1 target 0 lun 0
    pass2: <ata wdc="" wd2502abys-1="" 3b05="">Fixed Uninstalled SCSI-5 device
    pass2: 300.000MB/s transfers
    pass2: Command Queueing enabled
    SMP: AP CPU #1 Launched!
    Root mount waiting for: usbus2
    ugen2.2: <vendor 0x0424="">at usbus2
    uhub8: <vendor 2="" 9="" 0x0424="" product="" 0x2514,="" class="" 0,="" rev="" 2.00="" 0.00,="" addr="">on usbus2
    ugen0.2: <dell>at usbus0
    ukbd0: <ep1 interrupt="">on usbus0
    kbd2 at ukbd0
    Root mount waiting for: usbus2
    uhub8: 4 ports with 4 removable, self powered
    Trying to mount root from ufs:/dev/da0s1a
    pflog0: promiscuous mode enabled
    bce1: link state changed to UP
    interrupt                          total      rate
    irq17: uhci0                          19          0
    irq19: ehci0                        247          1
    irq22: atapci1                        68          0
    irq32: mpt0                        2065          9
    cpu0: timer                      441265      1987
    irq256: bce0                          1          0
    irq257: bce1                        120          0
    cpu1: timer                      431253      1942
    Total                            875038      3941

    6th Test

    Reset CPU to All Cores in BIOS Settings
    Everything Works!

    R510 w/ both NICs installed, CPU = ALL

    $ dmesg; vmstat -i
    Copyright © 1992-2010 The FreeBSD Project.
    Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
    The Regents of the University of California. All rights reserved.
    FreeBSD is a registered trademark of The FreeBSD Foundation.
    FreeBSD 8.1-RELEASE-p2 #0: Sat Feb 26 15:29:09 EST 2011
        sullrich@FreeBSD_8.0_pfSense_2.0-snaps.pfsense.org:/usr/obj.pfSense/usr/pfSensesrc/src/sys/pfSense_SMP.8 i386
    Timecounter "i8254" frequency 1193182 Hz quality 0
    CPU: Intel(R) Xeon(R) CPU          E5503  @ 2.00GHz (2000.08-MHz 686-class CPU)
      Origin = "GenuineIntel"  Id = 0x106a5  Family = 6  Model = 1a  Stepping = 5
      Features=0xbfebfbff <fpu,vme,de,pse,tsc,msr,pae,mce,cx8,apic,sep,mtrr,pge,mca,cmov,pat,pse36,clflush,dts,acpi,mmx,fxsr,sse,sse2,ss,htt,tm,pbe>Features2=0x9ce3bd <sse3,dtes64,mon,ds_cpl,vmx,est,tm2,ssse3,cx16,xtpr,pdcm,dca,sse4.1,sse4.2,popcnt>AMD Features=0x28100000 <nx,rdtscp,lm>AMD Features2=0x1 <lahf>TSC: P-state invariant
    real memory  = 2147483648 (2048 MB)
    avail memory = 2069499904 (1973 MB)
    ACPI APIC Table: <dell  pe_sc3 ="">FreeBSD/SMP: Multiprocessor System Detected: 4 CPUs
    FreeBSD/SMP: 2 package(s) x 2 core(s)
    cpu0 (BSP): APIC ID: 16
    cpu1 (AP): APIC ID: 20
    cpu2 (AP): APIC ID:  0
    cpu3 (AP): APIC ID:  4
    ioapic1: Changing APIC ID to 1
    ioapic0 <version 2.0="">irqs 0-23 on motherboard
    ioapic1 <version 2.0="">irqs 32-55 on motherboard
    wpi: You need to read the LICENSE file in /usr/share/doc/legal/intel_wpi/.
    wpi: If you agree with the license, set legal.intel_wpi.license_ack=1 in /boot/loader.conf.
    module_register_init: MOD_LOAD (wpi_fw, 0xc095c1e0, 0) error 1
    ipw_bss: You need to read the LICENSE file in /usr/share/doc/legal/intel_ipw/.
    ipw_bss: If you agree with the license, set legal.intel_ipw.license_ack=1 in /boot/loader.conf.
    module_register_init: MOD_LOAD (ipw_bss_fw, 0xc0767240, 0) error 1
    ipw_ibss: You need to read the LICENSE file in /usr/share/doc/legal/intel_ipw/.
    ipw_ibss: If you agree with the license, set legal.intel_ipw.license_ack=1 in /boot/loader.conf.
    module_register_init: MOD_LOAD (ipw_ibss_fw, 0xc0767300, 0) error 1
    ipw_monitor: You need to read the LICENSE file in /usr/share/doc/legal/intel_ipw/.
    ipw_monitor: If you agree with the license, set legal.intel_ipw.license_ack=1 in /boot/loader.conf.
    module_register_init: MOD_LOAD (ipw_monitor_fw, 0xc07673c0, 0) error 1
    wlan: mac acl policy registered
    kbd1 at kbdmux0
    cryptosoft0: <software crypto="">on motherboard
    padlock0: No ACE support.
    acpi0: <dell pe_sc3="">on motherboard
    acpi0: [ITHREAD]
    acpi0: Power Button (fixed)
    Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
    acpi_timer0: <24-bit timer at 3.579545MHz> port 0x808-0x80b on acpi0
    cpu0: <acpi cpu="">on acpi0
    cpu1: <acpi cpu="">on acpi0
    cpu2: <acpi cpu="">on acpi0
    cpu3: <acpi cpu="">on acpi0
    acpi_hpet0: <high precision="" event="" timer="">iomem 0xfed00000-0xfed003ff on acpi0
    Timecounter "HPET" frequency 14318180 Hz quality 900
    pcib0: <acpi host-pci="" bridge="">port 0xcf8-0xcff on acpi0
    pci0: <acpi pci="" bus="">on pcib0
    pcib1: <acpi pci-pci="" bridge="">at device 1.0 on pci0
    pci1: <acpi pci="" bus="">on pcib1
    bce0: <broadcom netxtreme="" ii="" bcm5716="" 1000base-t="" (c0)="">mem 0xd6000000-0xd7ffffff irq 36 at device 0.0 on pci1
    miibus0: <mii bus="">on bce0
    brgphy0: <bcm5709c 10="" 100="" 1000basetx="" phy="">PHY 1 on miibus0
    brgphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto
    bce0: [ITHREAD]
    bce0: ASIC (0x57092008); Rev (C0); Bus (PCIe x4, 2.5Gbps); B/C (5.2.3); Flags (MSI|MFW); MFW (NCSI 2.0.11)
    bce1: <broadcom netxtreme="" ii="" bcm5716="" 1000base-t="" (c0)="">mem 0xd8000000-0xd9ffffff irq 48 at device 0.1 on pci1
    miibus1: <mii bus="">on bce1
    brgphy1: <bcm5709c 10="" 100="" 1000basetx="" phy="">PHY 1 on miibus1
    brgphy1:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto
    bce1: [ITHREAD]
    bce1: ASIC (0x57092008); Rev (C0); Bus (PCIe x4, 2.5Gbps); B/C (5.2.3); Flags (MSI|MFW); MFW (NCSI 2.0.11)
    pcib2: <acpi pci-pci="" bridge="">at device 3.0 on pci0
    pci2: <acpi pci="" bus="">on pcib2
    mpt0: <lsilogic sas="" sata="" adapter="">port 0xfc00-0xfcff mem 0xde2ec000-0xde2effff,0xde2f0000-0xde2fffff irq 32 at device 0.0 on pci2
    mpt0: [ITHREAD]
    mpt0: MPI Version=1.5.18.0
    mpt0: Capabilities: ( RAID-0 RAID-1E RAID-1 )
    mpt0: 1 Active Volume (2 Max)
    mpt0: 2 Hidden Drive Members (14 Max)
    pcib3: <acpi pci-pci="" bridge="">at device 7.0 on pci0
    pci3: <acpi pci="" bus="">on pcib3
    pcib4: <pci-pci bridge="">at device 0.0 on pci3
    pci4: <pci bus="">on pcib4
    pcib5: <pci-pci bridge="">at device 2.0 on pci4
    pci5: <pci bus="">on pcib5
    igb0: <intel(r) 1000="" pro="" network="" connection="" version="" -="" 2.0.7="">port 0xecc0-0xecdf mem 0xdbfc0000-0xdbfdffff,0xdc000000-0xdc3fffff,0xdbfb8000-0xdbfbbfff irq 47 at device 0.0 on pci5
    igb0: Using MSIX interrupts with 5 vectors
    igb0: [ITHREAD]
    igb0: [ITHREAD]
    igb0: [ITHREAD]
    igb0: [ITHREAD]
    igb0: [ITHREAD]
    igb1: <intel(r) 1000="" pro="" network="" connection="" version="" -="" 2.0.7="">port 0xece0-0xecff mem 0xdbfe0000-0xdbffffff,0xdc400000-0xdc7fffff,0xdbfbc000-0xdbfbffff irq 46 at device 0.1 on pci5
    igb1: Using MSIX interrupts with 5 vectors
    igb1: [ITHREAD]
    igb1: [ITHREAD]
    igb1: [ITHREAD]
    igb1: [ITHREAD]
    igb1: [ITHREAD]
    pcib6: <pci-pci bridge="">at device 4.0 on pci4
    pci6: <pci bus="">on pcib6
    igb2: <intel(r) 1000="" pro="" network="" connection="" version="" -="" 2.0.7="">port 0xdcc0-0xdcdf mem 0xdb3c0000-0xdb3dffff,0xdb400000-0xdb7fffff,0xdb3b8000-0xdb3bbfff irq 38 at device 0.0 on pci6
    igb2: Using MSIX interrupts with 5 vectors
    igb2: [ITHREAD]
    igb2: [ITHREAD]
    igb2: [ITHREAD]
    igb2: [ITHREAD]
    igb2: [ITHREAD]
    igb3: <intel(r) 1000="" pro="" network="" connection="" version="" -="" 2.0.7="">port 0xdce0-0xdcff mem 0xdb3e0000-0xdb3fffff,0xdb800000-0xdbbfffff,0xdb3bc000-0xdb3bffff irq 45 at device 0.1 on pci6
    igb3: Using MSIX interrupts with 5 vectors
    igb3: [ITHREAD]
    igb3: [ITHREAD]
    igb3: [ITHREAD]
    igb3: [ITHREAD]
    igb3: [ITHREAD]
    pcib7: <acpi pci-pci="" bridge="">at device 9.0 on pci0
    pci7: <acpi pci="" bus="">on pcib7
    pcib8: <pci-pci bridge="">at device 0.0 on pci7
    pci8: <pci bus="">on pcib8
    pcib9: <pci-pci bridge="">at device 2.0 on pci8
    pci9: <pci bus="">on pcib9
    igb4: <intel(r) 1000="" pro="" network="" connection="" version="" -="" 2.0.7="">port 0xccc0-0xccdf mem 0xdd7c0000-0xdd7dffff,0xdd800000-0xddbfffff,0xdd7b8000-0xdd7bbfff irq 55 at device 0.0 on pci9
    igb4: Using MSIX interrupts with 5 vectors
    igb4: [ITHREAD]
    igb4: [ITHREAD]
    igb4: [ITHREAD]
    igb4: [ITHREAD]
    igb4: [ITHREAD]
    igb5: <intel(r) 1000="" pro="" network="" connection="" version="" -="" 2.0.7="">port 0xcce0-0xccff mem 0xdd7e0000-0xdd7fffff,0xddc00000-0xddffffff,0xdd7bc000-0xdd7bffff irq 49 at device 0.1 on pci9
    igb5: Using MSIX interrupts with 5 vectors
    igb5: [ITHREAD]
    igb5: [ITHREAD]
    igb5: [ITHREAD]
    igb5: [ITHREAD]
    igb5: [ITHREAD]
    pcib10: <pci-pci bridge="">at device 4.0 on pci8
    pci10: <pci bus="">on pcib10
    igb6: <intel(r) 1000="" pro="" network="" connection="" version="" -="" 2.0.7="">port 0xbcc0-0xbcdf mem 0xdcbc0000-0xdcbdffff,0xdcc00000-0xdcffffff,0xdcbb8000-0xdcbbbfff irq 40 at device 0.0 on pci10
    igb6: Using MSIX interrupts with 5 vectors
    igb6: [ITHREAD]
    igb6: [ITHREAD]
    igb6: [ITHREAD]
    igb6: [ITHREAD]
    igb6: [ITHREAD]
    igb7: <intel(r) 1000="" pro="" network="" connection="" version="" -="" 2.0.7="">port 0xbce0-0xbcff mem 0xdcbe0000-0xdcbfffff,0xdd000000-0xdd3fffff,0xdcbbc000-0xdcbbffff irq 50 at device 0.1 on pci10
    igb7: Using MSIX interrupts with 5 vectors
    igb7: [ITHREAD]
    igb7: [ITHREAD]
    igb7: [ITHREAD]
    igb7: [ITHREAD]
    igb7: [ITHREAD]
    pcib11: <acpi pci-pci="" bridge="">at device 10.0 on pci0
    pci11: <acpi pci="" bus="">on pcib11
    pci0: <base peripheral,="" interrupt="" controller=""> at device 20.0 (no driver attached)
    pci0: <base peripheral,="" interrupt="" controller=""> at device 20.1 (no driver attached)
    pci0: <base peripheral,="" interrupt="" controller=""> at device 20.2 (no driver attached)
    uhci0: <intel 82801ji="" (ich10)="" usb="" controller="" usb-d="">port 0xac40-0xac5f irq 17 at device 26.0 on pci0
    uhci0: [ITHREAD]
    usbus0: <intel 82801ji="" (ich10)="" usb="" controller="" usb-d="">on uhci0
    uhci1: <intel 82801ji="" (ich10)="" usb="" controller="" usb-e="">port 0xac60-0xac7f irq 18 at device 26.1 on pci0
    uhci1: [ITHREAD]
    usbus1: <intel 82801ji="" (ich10)="" usb="" controller="" usb-e="">on uhci1
    ehci0: <intel 82801ji="" (ich10)="" usb="" 2.0="" controller="" usb-b="">mem 0xde0fe000-0xde0fe3ff irq 19 at device 26.7 on pci0
    ehci0: [ITHREAD]
    usbus2: EHCI version 1.0
    usbus2: <intel 82801ji="" (ich10)="" usb="" 2.0="" controller="" usb-b="">on ehci0
    uhci2: <intel 82801ji="" (ich10)="" usb="" controller="" usb-a="">port 0xac80-0xac9f irq 21 at device 29.0 on pci0
    uhci2: [ITHREAD]
    usbus3: <intel 82801ji="" (ich10)="" usb="" controller="" usb-a="">on uhci2
    uhci3: <intel 82801ji="" (ich10)="" usb="" controller="" usb-b="">port 0xaca0-0xacbf irq 20 at device 29.1 on pci0
    uhci3: [ITHREAD]
    usbus4: <intel 82801ji="" (ich10)="" usb="" controller="" usb-b="">on uhci3
    uhci4: <intel 82801ji="" (ich10)="" usb="" controller="" usb-c="">port 0xacc0-0xacdf irq 21 at device 29.2 on pci0
    uhci4: [ITHREAD]
    usbus5: <intel 82801ji="" (ich10)="" usb="" controller="" usb-c="">on uhci4
    uhci5: <intel 82801ji="" (ich10)="" usb="" controller="" usb-f="">port 0xace0-0xacff irq 20 at device 29.3 on pci0
    uhci5: [ITHREAD]
    usbus6: <intel 82801ji="" (ich10)="" usb="" controller="" usb-f="">on uhci5
    ehci1: <intel 82801ji="" (ich10)="" usb="" 2.0="" controller="" usb-a="">mem 0xde0ff000-0xde0ff3ff irq 21 at device 29.7 on pci0
    ehci1: [ITHREAD]
    usbus7: EHCI version 1.0
    usbus7: <intel 82801ji="" (ich10)="" usb="" 2.0="" controller="" usb-a="">on ehci1
    pcib12: <acpi pci-pci="" bridge="">at device 30.0 on pci0
    pci12: <acpi pci="" bus="">on pcib12
    vgapci0: <vga-compatible display="">mem 0xd5800000-0xd5ffffff,0xda7fc000-0xda7fffff,0xda800000-0xdaffffff irq 19 at device 3.0 on pci12</vga-compatible></acpi></acpi></intel></intel></intel></intel></intel></intel></intel></intel></intel></intel></intel></intel></intel></intel></intel></intel></acpi></acpi></intel(r)></intel(r)></pci></pci-pci></intel(r)></intel(r)></pci></pci-pci></pci></pci-pci></acpi></acpi></intel(r)></intel(r)></pci></pci-pci></intel(r)></intel(r)></pci></pci-pci></pci></pci-pci></acpi></acpi></lsilogic></acpi></acpi></bcm5709c></mii></broadcom></bcm5709c></mii></broadcom></acpi></acpi></acpi></acpi></high></acpi></acpi></acpi></acpi></dell></software></version></version></dell ></lahf></nx,rdtscp,lm></sse3,dtes64,mon,ds_cpl,vmx,est,tm2,ssse3,cx16,xtpr,pdcm,dca,sse4.1,sse4.2,popcnt></fpu,vme,de,pse,tsc,msr,pae,mce,cx8,apic,sep,mtrr,pge,mca,cmov,pat,pse36,clflush,dts,acpi,mmx,fxsr,sse,sse2,ss,htt,tm,pbe></ep1></dell></vendor></vendor></ata></dell></dp></teac></intel></intel></intel></intel></intel></intel></intel></intel></intel></intel></intel></intel></intel></intel></intel></intel></cpu></enhanced></cpu></enhanced></at></keyboard></generic></system></isa></at></ata></ata></intel></ata></ata></intel></isa></pci-isa></vga-compatible></acpi></acpi></intel></intel></intel></intel></intel></intel></intel></intel></intel></intel></intel></intel></intel></intel></intel></intel></acpi></acpi></intel(r)></intel(r)></pci></pci-pci></intel(r)></intel(r)></pci></pci-pci></pci></pci-pci></acpi></acpi></intel(r)></intel(r)></pci></pci-pci></intel(r)></intel(r)></pci></pci-pci></pci></pci-pci></acpi></acpi></lsilogic></acpi></acpi></bcm5709c></mii></broadcom></bcm5709c></mii></broadcom></acpi></acpi></acpi></acpi></high></acpi></acpi></dell></software></version></version></dell ></lahf></nx,rdtscp,lm></sse3,dtes64,mon,ds_cpl,vmx,est,tm2,ssse3,cx16,xtpr,pdcm,dca,sse4.1,sse4.2,popcnt></fpu,vme,de,pse,tsc,msr,pae,mce,cx8,apic,sep,mtrr,pge,mca,cmov,pat,pse36,clflush,dts,acpi,mmx,fxsr,sse,sse2,ss,htt,tm,pbe></ep1></dell></vendor></vendor></ata></dell></dp></teac></intel></intel></intel></intel></intel></intel></intel></intel></intel></intel></intel></intel></intel></intel></intel></intel></cpu></enhanced></cpu></enhanced></at></keyboard></generic></system></isa></at></ata></ata></intel></ata></ata></intel></isa></pci-isa></vga-compatible></acpi></acpi></intel></intel></intel></intel></intel></intel></intel></intel></intel></intel></intel></intel></intel></intel></intel></intel></acpi></acpi></acpi></acpi></intel(r)></intel(r)></pci></pci-pci></intel(r)></intel(r)></pci></pci-pci></pci></pci-pci></acpi></acpi></lsilogic></acpi></acpi></bcm5709c></mii></broadcom></bcm5709c></mii></broadcom></acpi></acpi></acpi></acpi></high></acpi></acpi></dell></software></version></version></dell ></lahf></nx,rdtscp,lm></sse3,dtes64,mon,ds_cpl,vmx,est,tm2,ssse3,cx16,xtpr,pdcm,dca,sse4.1,sse4.2,popcnt></fpu,vme,de,pse,tsc,msr,pae,mce,cx8,apic,sep,mtrr,pge,mca,cmov,pat,pse36,clflush,dts,acpi,mmx,fxsr,sse,sse2,ss,htt,tm,pbe></ep1></dell></vendor></vendor></ata></dell></dp></teac></intel></intel></intel></intel></intel></intel></intel></intel></intel></intel></intel></intel></intel></intel></intel></intel></cpu></enhanced></cpu></enhanced></cpu></enhanced></cpu></enhanced></at></keyboard></generic></system></isa></at></ata></ata></intel></ata></ata></intel></isa></pci-isa></vga-compatible></acpi></acpi></intel></intel></intel></intel></intel></intel></intel></intel></intel></intel></intel></intel></intel></intel></intel></intel></acpi></acpi></acpi></acpi></intel(r)></intel(r)></pci></pci-pci></intel(r)></intel(r)></pci></pci-pci></pci></pci-pci></acpi></acpi></lsilogic></acpi></acpi></bcm5709c></mii></broadcom></bcm5709c></mii></broadcom></acpi></acpi></acpi></acpi></high></acpi></acpi></acpi></acpi></dell></software></version></version></dell ></lahf></nx,rdtscp,lm></sse3,dtes64,mon,ds_cpl,vmx,est,tm2,ssse3,cx16,xtpr,pdcm,dca,sse4.1,sse4.2,popcnt></fpu,vme,de,pse,tsc,msr,pae,mce,cx8,apic,sep,mtrr,pge,mca,cmov,pat,pse36,clflush,dts,acpi,mmx,fxsr,sse,sse2,ss,htt,tm,pbe></enter>



  • So in summary…

    It appears I can get the system up and running (without crippling the physical system) by installing 1st without any of the add-in nics installed.  However, this whole process has left me with an uneasy feeling to move forward into production with these systems.  Doesn't it stand to reason that if the install had such troubles than I may run into issues once the system is in production and under load?

    Thanks,

    Jeff



  • I can't offer an explanation for the difficulty you have had with the initial installs.

    Maybe it would be worthwhile cloning the hard drive and putting the original away as a backup to help you get running again quickly if you have hard drive problems.

    I expect there would be lots of pfSense users who rarely do an install; they do a firmware upgrade instead. I wouldn't be at all surprised if the install process is much less exercised than the "production" software.



  • wallabybob,

    Thanks for the suggestion.  These systems both have a Hardware RAID-1 setup.  I wanted the redundancy.  Makes pulling hard drives a more difficult and expensive process.  But, maybe it is worthwhile seeing if I can disable the RAID and see what happens during the install?

    Jeff



  • Disabling the RAID made no difference.

    Also, I was too optimistic with my analysis.  Even though the system came up fine after installing the NIC cards, as soon as I started configuring it via the web interface, things got wacky.  After each change I would lose access to the web interface.  I could still ping the firewall and the console was still OK.  But, even restarting the webconfigurator from the console would not bring access to the web gui back.  I had to fully reboot the server.

    I think I'll start up a new thread that references this thread.  Since this one is getting long winded, I want to post a summary of my issues and what my options are moving forward.


Log in to reply