@akuma1x Yup I did look at that, but I need more storage so I went for an 8 slot device, that I'll never fill.

One of the guys I work with is having the 415+

Yup, I was already watching. There it is!

@pirotor

It's possible.
Install the pfSense Cron package.
Add your 'wol' command and the moment you want to execute it.
Done.

SFP+ are supported by ix drivers too, they work fine also.
My only issue for such an overkill board is having to add an intel x710 card to add some multigig ports to connect 2.5gbps to my modem.

Yes, the 5100 should run CE no problems.

You should reinstall to do that but you can import your config from Factory.

Steve

@rmaeder Here you go... Its one release back,

a411c3c0-3ef3-4199-a74f-3c1210a3ffe3-image.png

@stephenw10 I now have two nanoHD's doing nothing. I noticed that there is an OpenWRT package for those. Looks very recent and maybe beta. Not sure, didn't spend a lot of time digging. Anyone have any knowledge about the nanoHD and OpenWRT? With the Unifi FW the performance was terrible under load, so maybe not even worth the effort?

Thanks!

Happy New Year to you!

Deutsch:
Einen guten Start ins neue Jahr 2021! Bleibt gesund, denn es kann nur besser werden!

@gambiarraweb1
hello
the instruction to install influx are here
https://docs.influxdata.com/influxdb/v1.8/introduction/install/
github contain also screenshot of what you need to set on pfsense, inside the "images" folder.
what are you unable to do specifically?

@gertjan Agreed. However, an email outage is not as tragic as it once would have been. I, and I suspect many others, don't see email as critical communications. It's the use of an email address as identity that is troubling. I regularly go days or weeks without sending an email. I do use email addresses multiple times everyday to logon to various services. 2FA is a band-aid at best, security theater most of the time.

@johnpoz said in Merry Christmas:
I for sure will not be driving for that first meetup.. hehehe

😂 😂 😂

I wish to all a good passage to the New Year and all the Best!

Regards,
fireodo

@johnpoz, @jwj Thank you

I assume you mean hardware to run as a firewall/router with pfSense rather than just to generate traffic?

The graphics card makes no difference at all here other than potentially being unsupported by pfSense at all making install difficult. Better to use on-board video in most cases or serial console.

You don't mention RAM there but it's not really significant for high throughput.

Network card choice is though. Use something Intel based, ix or ixl.

There is a huge variation in performance across the range of E3 v3 CPUs, you need to be more specific. But the Ryzen 3900X appears more powerful than any of them. In a synthetic benchmark at least.

The 5Gbps VPN requirement is a far harder ask then 10Gbps total throughput. But again there are many variables there.

Steve

@Sergei_Shablovsky

Yes.
https://qna.habr.com/q/862669

@tman222

I'll answer your question about nohz
it does not work on raspberry pi 4 + raspbian
the kernel isn't configured to allows the nohz parameter to work
also, I found that you can only use
flag 3 0 (use the ntpd clock discipline)
and not
flag 3 1 (use the kernel discipline)
for PPS
if you try to use flag 3 1 you see in the syslog this:

refclock_params: time_pps_kcbind: Operation not supported

this is because the kernel is compiled without CONFIG_NTP_PPS

Immagine.jpg

obviusly
as a good nerd I recompiled ... 😑

this is ublox now

server 127.127.20.0 mode 89 iburst prefer minpoll 2 maxpoll 4 fudge 127.127.20.0 flag1 1 flag3 1 time1 0.0 time2 0.025 refid GPS pi@raspberrypi3:~/linux $ uname -a Linux raspberrypi3 4.19.118-v7lntp+ #1 SMP Fri Dec 11 14:42:08 CET 2020 armv7l GNU/Linux pi@raspberrypi3:~/linux $ ntpq -crv -pn status=041d leap_none, sync_uhf_radio, 1 event, kern, version="ntpd ntpsec-1.1.3 2019-11-18T06:04:00Z", processor="armv7l", system=" Linux/4.19.118-v7lntp+", leap=00, stratum=1, precision=-20, rootdelay=0.0, rootdisp=2.18, refid=GPS, reftime=e37e600c.8bd6769d 2020-12-11T21:15:56.546Z, clock=e37e6018.d0a57250 2020-12-11T21:16:08.815Z, peer=11020, tc=4, mintc=0, offset=7.8e-05, frequency=-18.907623, sys_jitter=0.000277, clk_jitter=0.000728, clk_wander=0.001816, tai=37, leapsec="2017-01-01T00:00Z", expire="2021-06-28T00:00Z" remote refid st t when poll reach delay offset jitter ======================================================================================================= oNMEA(0) .GPS. 0 l 12 16 377 0.0000 0.0001 0.0003

Immagine.jpg

The card you have linked to is the QXG-10G2T-107. But for either we would need to know what chipset it uses.

Edit: Looks like Mellanox ConnectX-4 LX....
If that's true they may be supported by:
https://www.freebsd.org/cgi/man.cgi?query=mlx5en

Would need to know the actual PCI IDs to say further.

Steve