• I have problems with internet connection

    3
    0 Votes
    3 Posts
    428 Views
    M

    the address 192.168.0.196 is the one that gives me when putting virtual machine a bridge adapter

  • Two Problems -(Solved)

    4
    0 Votes
    4 Posts
    828 Views
    NollipfSenseN

    To solve the adding user problem, I just deleted the user and will use admin for now until PFSense fixed

  • Site to site OpenVPN for only some traffic

    2
    0 Votes
    2 Posts
    327 Views
    S

    If I'm understanding your question correctly, the way to do this is to connect via the external IP instead of the internal IP that presumably routes thru the tunnel.  But then you'd have to allow ssh connections thru the WAN interface, which seems like a bad idea.  Why don't you want ssh connections to go thru the tunnel?

  • PFBlockerNG - want to allow country but also SIP provider on static IP

    1
    0 Votes
    1 Posts
    290 Views
    No one has replied
  • How to configure PPPOE + DMZ with multi IPs

    1
    0 Votes
    1 Posts
    280 Views
    No one has replied
  • MOVED: Problem using a Port Range in an Alias - Possible Bug?

    Locked
    1
    0 Votes
    1 Posts
    221 Views
    No one has replied
  • [SOLVED]: NetBios browsing across subnets/VLANS

    9
    0 Votes
    9 Posts
    3k Views
    DerelictD

    Then they are broken or improperly-configured if they are passing broadcasts between VLANs.

    And proper configuration should not require anything such as "port isolation."

  • Diagnostics / pfInfo Page

    1
    0 Votes
    1 Posts
    349 Views
    No one has replied
  • Traffic accounting / state logging

    1
    0 Votes
    1 Posts
    527 Views
    No one has replied
  • PFSense Traffic Graph

    1
    0 Votes
    1 Posts
    459 Views
    No one has replied
  • Configuration Problem Prod-DEV Subnets

    1
    0 Votes
    1 Posts
    182 Views
    No one has replied
  • Speed

    10
    0 Votes
    10 Posts
    1k Views
    M

    I did this with 8 modems each with 250 Mbps down and 10 and 20 Mbps up and I was able to achieve about 960 Mbps download speed and 120 Mbps upload speed. The reason I didn't see a greater speed increase was two issues, first my computer and router only have gigabit ports on them. I also I was using two cable nodes and that was the physical limitation of their downstream and upstream channels. While this works great on bandwidth speed test sites in real-world scenarios like VoIP and TLS connections it is better to using one WAN which I believe there is a setting for. One of the issues that I had was I had to manually increment the MAC address on each interface as I was using a switch as a wan aggregator using VLANs and the ISP (My Job) that I was testing this on assigns IPs to customers by MAC addresses. I later took the modems out of bridge mode and just used the ISP provided modems in gateway mode and just added my PfSense box to the DMZ of each gateway. In the end like others have mentioned it is probably best to use policy based routing and give each over your subnets it's own WAN.

    On a side note I was seeing near perfect scaling. I believe I posted about this I will try to find that post. If I find it I will add the link below.

    https://forum.pfsense.org/index.php?topic=126468.msg698424#msg698424

  • Is it possible to modify the pfsense login page (NOT CAPTIVE PORTAL)

    6
    0 Votes
    6 Posts
    2k Views
    R

    @BlueKobold:

    Possible to get to that html file and add 3 simple characters?

    And what will be shown then on the page? How it is looking then

    I was going to put my firewall hostname.

    Now that i have turned on the option for hostname and set unique color for each site I'm quite happy.  Just what I wanted to do and both already features of the software.

    Roveer

  • Sonos' IGMP packets aren't handled properly

    3
    0 Votes
    3 Posts
    2k Views
    B

    @BlueKobold:

    Your router or firewall should be placed in the same VLAN as the Sonos products as well. If this will be not so
    you must do some monkeying around and setting up all switches that are involved into your network too!

    Here is an article that is describing how to set up the switch, that all is well playing together.
    Sonos and VLANs

    That sonos support doc shows the configuration for a cisco switch (who has those at home?) that I believe basically understand this igmp packet that I posted above and then re-broadcasts for you in the various ports/vlans. What I am asking is if it is possible to get a igmpproxy in pfsense that understands these igmp packets.

  • Lan multicast is being blocked by default rules

    17
    0 Votes
    17 Posts
    7k Views
    bingo600B

    @johnpoz:

    "I always looked at the log every day to see who is attacking."

    Noise on the internet is not attacking ;)  I log the syn traffic.. But I don't want to see all the noise.. Out of state, UDP, etc.

    John

    Could you give an example of "just logging syn packets"
    I suppose you have a specific block rule with logging enables , and ANY w. SYN ,
    and then a block rule wo. logging or ??

    TIA
    /Bingo

  • Weirdest issue ever! Seems to be DNS problem but only on Twitter.

    18
    0 Votes
    18 Posts
    4k Views
    johnpozJ

    Its never had anything to do with pfsense at all ;)  dns problem give you that, but it was never something specific to pfsense.

    Like I said something not right with their dns.. you shouldn't point to different stuff like that..  if you going to use a CDN fine, but it sholdn't point to different cnames and have ones that just do one and then others than have 3 in a daisy chain, etc..

  • 2.3.x and FreeBSD 10.4

    2
    0 Votes
    2 Posts
    399 Views
    jimpJ

    At the moment, we plan to manually maintain any necessary security patches for 10.3. That is subject to change, naturally, if moving to 10.4 is easier than manually maintaining patches.

  • Reboot via ssh

    2
    0 Votes
    2 Posts
    5k Views
    jimpJ

    Use root, not admin.

    Or if you are using some other user that isn't root or admin, install the sudo package and grant that user rights to run commands as root (at least /etc/rc.reboot)

  • SVL 3 Problem

    5
    0 Votes
    5 Posts
    724 Views
    P

    Ok, i understand the problem. I thought there was a possibility
    to bypass it.

    Thank you anyway.

  • /var/run space totally consumed by gnid.core file

    4
    0 Votes
    4 Posts
    1k Views
    O

    Hi, I have the same problem, I could not find an answer in the Russian online segment. In this link, I posted a dump that was saved from me. Prior to the transition to version 2.3.5, there was no such problem.

    gnid.core = 4.7 MB

    https://drive.google.com/open?id=1FYiG2Y3rgMQGxgXc4l9g8LBHHczfxRWY

    var.run.109%.jpg
    var.run.109%.jpg_thumb
    ![after rm var.run.gnidcore.jpg](/public/imported_attachments/1/after rm var.run.gnidcore.jpg)
    ![after rm var.run.gnidcore.jpg_thumb](/public/imported_attachments/1/after rm var.run.gnidcore.jpg_thumb)

Copyright 2025 Rubicon Communications LLC (Netgate). All rights reserved.