1. Home
  2. pfSense® Software
  3. Problems Installing or Upgrading pfSense Software
Log in to post
Load new posts
  • ?

    HP Proliant DL320 G2 needs hpasmd - Custom pfSense compilation needed?

    7
    0 Votes
    7 Posts
    4k Views
    B
    I know this is an old thread, but I MUST get control of these fans on Proliant DL360 G3 server (and similar) The fans start off low, and once ANY amount of extra cooling is needed, it goes to 100% and hangs there until rebooted. So many have come so close to getting HPASM running, can we now take a stab at it again? If no, then here is the ONLY solution to this… Load VMware ESXi on these boxes and run the firewall as a single VM on them. Then you can load the VMware ESXi drivers that are supported by HP and since ESXi is FREE and WEB BASED, you should be good to go. The idea is actually a good one now that i think of it, because I would never have to rebuild my PFsense box again! I could just move the VM to any other HW i choose moving forward.
  • B

    BUG REPORT: Any install after 2.1.2 hangs on HP DL360 series HW.

    1
    0 Votes
    1 Posts
    705 Views
    No one has replied
  • M

    2.1.2 & 2.1.3 apinger and gateway monitoring broken!

    5
    0 Votes
    5 Posts
    2k Views
    M
    Hello This is sadly still true for 2.1.4. 2.1.4-RELEASE (amd64) built on Fri Jun 20 12:59:50 EDT 2014 FreeBSD 8.3-RELEASE-p16
  • C

    APU1C4 Boot issues

    4
    0 Votes
    4 Posts
    2k Views
    S
    @pvoigt: @spid: Hi, I have the same board, and also a Kingston 30gb SSD currently running 2.1.3 (Kingston SSDNow mS200 SMS200S3 30GB) Holding off on 2.1.4 until someone confirms 2.1.4 still works with serial console as some have reported problems with the update. I can confirm the serial console is still working with pfSense 2.1.4. I have tested this with an ALIX.2D13. You can find some more details here: https://forum.pfsense.org/index.php?topic=78713.msg429345#msg429345. Regards, Peter Thank you for your feedback, but i'm not running the nanobsd image but the full 64bit memstick installer with serial and after upgrading just now from the auto upgrade web page it all seems fine  8)
  • X

    PfSense 2.1.4 and MatrixOrbital LCD

    1
    0 Votes
    1 Posts
    845 Views
    No one has replied
  • O

    PfSense 2.1.4 amd64 vga updaters

    4
    0 Votes
    4 Posts
    1k Views
    O
    When can we expect a 2.1.4 vga release? At the moment, on https://updates.pfsense.org/_updaters/amd64/ I'm seeing again old release dates (02-May-2014) even though version-nanobsd-vga-4g contains the "2.1.4-RELEASE" version string: latest-nanobsd-vga-4g.img.gz                      02-May-2014 21:24            94184435 latest-nanobsd-vga-4g.img.gz.md5                  02-May-2014 21:24                  99 latest-nanobsd-vga-4g.img.gz.sha256                02-May-2014 21:24                134 version-nanobsd-vga-4g                            02-May-2014 21:24                  14 On my pfSense dashboard I still see the message "You are on the latest version." Will we ever be able to upgrade from 2.1.3 to 2.1.4?
  • I

    No WAN to LAN Throughput

    13
    0 Votes
    13 Posts
    2k Views
    stephenw10S
    Same sentiment from me. It's always better to ask questions than to struggle on alone for fear of saying the wrong thing.  ;) Since you have 4 NICs you can have a 1 WAN and 3 LAN setup (without using VLANs). 3 internal interfaces, 3 separate subnets with whatever firewall rules you choose to put in to filter traffic between them. You might choose to put any servers on one subnet, wireless clients on another and everything else on the last for example. If you want more segregation, firewall rules between each machine for example, you can add further interfaces using VLANs and your switch. Steve
  • N

    2.13-2.14 NAT, Firewall Issue

    4
    0 Votes
    4 Posts
    1k Views
    R
    Yes - every port forward created in the NAT section generates a firewall rule on the wan interface. Now if you disable the port forward, the firewall rule still shows as enabled, although it doesn't function anymore. This behavior is like this as I observed in 2.1, 2.1.1, 2.1.3.
  • B

    Firmware upgrade architecture

    3
    0 Votes
    3 Posts
    991 Views
    B
    jimp, Thanks for the explanation.  It just seemed a bit strange, in terms of the "normal" GUI style.
  • K

    Installing Pfsense on disk issues

    Locked
    2
    0 Votes
    2 Posts
    2k Views
    K
    Update, after doing a multitude of trial and error (which will be listed at the bottom), i got it past the installation,through the reboot and on to configuring pf sense on my main computer. The last method i tried was placing the hard-drive into slave mode while having the disk reader as the master on the first channel of the motherboards pata controller. 1* I feel really stupid and confused on why or how this worked. I do not believe that it has anything to do with the jumpers on the devices (master, slave) nor do i believe that the access mode (LBA) has anything do do with it (maybe) because I tried multiple combinations of everything. on a side note: I switched installation dvds and burnt myself a copy of pfsense 2.1.4 i386, which did not also worked untill I did the change above. The changes that i made were (not in chronological order, also the ones i can remember) reformatting and partitioning the drive via FreeBSD 8.3 i386 dvd (Errors when installing freebsd but partition and formats remained) switching: Pata cables, sata and pata Harddrive, cd/dvd burners, memory turning off: ps/2 mouse, onboard 1394, Serial ports, Parralel ports ,usb legacy mode support(which was turned back on) installing windows xp(which the machine Had), and updating Bios as well as partitioning the disk attempted to use pfsense live cd shell and try to learn fdisk to get a hint as to what the problem was edit: 1* as opposed to having both hard drive and disk reader be the master of their respective pata channels : hdd = channel 2 , Disk = channel 1
  • S

    Upgrade??

    1
    0 Votes
    1 Posts
    759 Views
    No one has replied
  • D

    Factory Default not working after upgrade to 2.1.3

    7
    0 Votes
    7 Posts
    2k Views
    D
    @downtown: @downtown: Same issue here. Warning: copy(/conf.default/config.xml): failed to open stream: No such file or directory in /etc/inc/config.lib.inc on line 605 Could someone with the file please post its contents so I can create it and carry on? Never mind, it's here: https://github.com/pfsense/pfsense/blob/master/conf.default/config.xml I can confirm that creating the file with the contents of the source from github solved the problem.
  • F

    My Antique WRAP 1E-2E, upgrade?

    6
    0 Votes
    6 Posts
    2k Views
    stephenw10S
    You could also run the X86 flavour of OpenWRT on the WRAP: http://wiki.openwrt.org/toh/pcengines/wrap and add multiwan: http://wiki.openwrt.org/doc/uci/multiwan Steve
  • D

    "clog: ERROR: could not write output (Bad address)"

    4
    0 Votes
    4 Posts
    2k Views
    D
    Thanks for the info on CLOG, but I was getting similar errors on other logs as well, for example /var/log/system.log and dmesg.log, after a day or two. I also had other issues, as weak MB battery, so my settings kept on changing randomly, but the main problem was an old HD with bad sectors! Rrrr. Using old hardware doesn´t seem to be a good idea. Replaced…. much better!!!
  • B

    How to upgrade packages without losing configuration?

    8
    0 Votes
    8 Posts
    2k Views
    BBcan177B
    Looks like the deinstall option will be defaulted to "on" with the next release but only for new installs. https://github.com/pfsense/pfsense-packages/pull/678
  • jimpJ

    MOVED: Problems with serial output after install

    Locked
    1
    0 Votes
    1 Posts
    564 Views
    No one has replied
  • P

    Install to KVM VPS does not see hard disk - requires VirtIO

    6
    0 Votes
    6 Posts
    2k Views
    P
    Any thoughts on how I might be able to make this install. I did what was mentioned but the install routine does not see the disk controller. Help! Paul.
  • L

    PPPOE : not obtaining an IP-address

    9
    0 Votes
    9 Posts
    4k Views
    L
    I started all over again by reinstalling Pfsense with all your advices and now its working. Thanks for all the advice Luc
  • T

    Installation Error, Fatal Trap 12 - devfs_populate_loop

    11
    0 Votes
    11 Posts
    3k Views
    T
    Hi Guys, Just want to update regarding this thread. I tried many things, including replacing HD but still could not solve the issue. Then I add another 2G RAM (become 4G RAM) into this server, then I install VM (ESXi), and pfsense on top of that VM. It works fine. So just FYI guys if you see similar issue, you may want to consider using VM instead. Thanks all for help.
  • N

    Auto update installed i386 version to AMD64 system

    9
    0 Votes
    9 Posts
    2k Views
    jimpJ
    Actually, on 2.1 and later when you backup the RRD, assuming you start on the architecture matching the RRD files, it's backed up in an architecture-independent XML format. If you are on i386 with working graphs you can make a backup including RRD and then restore to amd64 and the graphs come back with it. At least, that's how it's supposed to work. I haven't tried it myself in a while. If your RRD data on the HDD is already wrong, then leave the RRD out of the backup and then once you switch back your RRD graphs will work again.
Copyright 2025 Rubicon Communications LLC (Netgate). All rights reserved.