Just to update this post … I recently installed 2.3.2-p1 on an old PC Engines ALIX 3D2 board. Much to my surprise the GUI works amazingly fast and I will update my other ALIX installs in the field. Write speed of the CF cards makes each update quite painfull though.

Well, about an hour after posting this, and after I'd already gone to sleep, it finished and sent me an email. Not sure why that update status page never progressed further (its gone now, back to the login screen after the auto-reboot). But the Status page does report its on "2.3.2-RELEASE-p1 " Cheers.

Yep, it turns out the problem was caused by all the DNS server entries config going away for some reason.  It's odd, because some resolution was still working…some IPs on the states table were converted to host names. All other connectivity seemed to be working fine.  Along with at least some host names in the state table (not everything will reverse), I didn't suspect DNS until I tried a few manual "curl" and "fetch" commands.

Yes, the "ADI" install files are the correct ones. The other installation media would not present a usable console so it's fairly obvious it's the wrong one. If it boots/installs/runs it's OK.

That. ^ You need to use the 32bit image on an ALIX board. Steve

I am having the same issue today, trying to restore the factory CentOS to a RCC-DFF 2220.  Tried multiple times using both USB from here as well as iPXE from http://install.netgate.com/rescue/CentOS7/centos7-rescue.ipxe Anyone have any ideas??  edit: here's a screenshot of the console output [image: 0tjDZZN.png] edit2: I tried another method that I had notes on from somewhere… this resulted in a slightly different but equally catastrophic failure (screenshot below) # initrd http://firmware.netgate.com/netinst/CentOS7/images/pxeboot/initrd.img # chain http://firmware.netgate.com/netinst/CentOS7/images/pxeboot/vmlinuz console=ttyS1,115200n8 ip=eth0:dhcp ks=http://firmware.netgate.com/netinst/ks.cfg inst.cmdline inst.text inst.headless net.ifnames=0 [image: CXSlUDO.png] I have that "/run/initramfs/rdsosreport.txt" file attached here as well. rdsosreport.txt

@KOM: Usual steps to make a generic wifi router an AP: 1.  Unplug/disable WAN 2.  Disable DHCP server 3.  Set LAN Static IP outside DHCP range 4.  Plug wifi LAN port into LAN switch Now it's acting as a wifi bridge to LAN. Added one step. Makes it easier to get back in if you need to.

No, you cannot have the same port for HTTP and HTTPS.

amd64 would be my preferred version, but that probably won't make a difference to get visuals or not

OK, but the remaining part, the messages during the upgrade, it is all ok?

Did you get this working?  I have something similar, but with mine I have Internet over Ethernet, but not with WiFi. You might need to change that Firewall setting to the 200.x subnet.

Hello Jdetmold, I am encountering the same issue as you. May I ask, were you able to get this to work? If so, how? Thanks in advance!

The Azure marketplace instance doesn't use the default login as it would be potentially exposed to everywhere. You set the login when you create it. See: http://www.netgate.com/docs/azure-appliance/quick-start-guide.html Steve

Well, I was pretty much sure I wouldn't be able to do that, but I was searching a confirmation. Sorry for the silly question and thanks @doktornotor for the answer!

what you're doing is essentially building a bullet proof car and using saran wrap as windows

I found this obscure IDE2SATA adapter i bought years ago in Japan, in my "other computer stuff" bin gave it a shot, cuz hey, why not. and it's working flawlessly off a 1 TB SATA Hard Drive now. its the same as this in case anyone has the same issue. https://www.amazon.ca/HDE-SATA-Drive-Interface-Adapter/dp/B0096BEJDI/ref=sr_1_1?ie=UTF8&qid=1481831549&sr=8-1&keywords=ide+to+sata