I searched on www for broadcast port 3490 and got answers about HP APs. And some solutions to disable the broadcasts. Do you have som HP network products on the LAN? Otherwise try do a packet capture and look for the MAC address of the source. Then you may be able to find the source of the broadcasts. /illern

If the Windows 8 + IE 10 + touch user agent is something we can detect, we can force it to switch the theme to the pfSense one. If you'd like to see those features in a theme, you're more than welcome to make a theme, offer a bounty to make one, or search around and find if someone has already made one that works like you want. IE barely functions with our GUI anyhow. Get a different browser ASAP.  ;D

I'm sure others will appreciate your findings if you put in the time doing some testing. Have you read this: https://wiki.freebsd.org/NetworkPerformanceTuning Enabling IP fastforwarding can have a significant impact on throughput, I wasn't looking at latency, but it kills ipsec if you're using it. http://forum.pfsense.org/index.php?topic=47567.0 Steve

I meant what does the interface report when you query if with ifconfig. Some cards have a problem with hardware vlan tagging, you can disable it on an interface (em0 here) like so: ifconfig emo -vlanhwtag If that works you can set it to run at boot using a cron job or with the Shellcmd package. Steve

You could use Firewall->Traffic Shaper, Limiter and put all your traffic into a limiter. That will slow you down all the time! But it is nice to be able to download at your full speed (8Mbps) so that a file download finishes quickly and you can use it. You just can't do that 24 hours a day on most home plans. There is nothing in pfSense to count the amount you have downloaded and give you a warning when you reach near your quota. Note: even if you limit to 1Mbps, that is about 7.5MB/min = 450MB/hour = 10.8GB/day = 324GB/month. If you have something on your network constantly downloading (and/or uploading = bittorrent…) then you will still chew up plenty of quota.

I am not a dansguardian user, so I am not familiar with the settings for that. You might get faster replies by posting in the Packages forum category.

Ok i see pfsense is using the syslogd is that right? I see there is also the syslog-ng installed but without any use as i see is that right too? I need to change the hostname in logging to the fqdn because i have more pfsense with the same hostname but different domain names. Does nobody else has the same problem?

Its solved, thank you so much..

I removed squid3-dev and installed squid3 package and it's working now. I don't know why.

I didn't know there was a package like that. Thanks @Jimp

Hi Steve, thank you for your answer… unfortunately both solutions didn't work... mbmon -c1 returns No Hardware Monitor found!! InitMBInfo: No error: 0 and sysctl -a | grep therm or sysctl -a | grep temper return no results… :( Ok, I got it, I will upgrade my firewall sooner or later... :D EDIT: and yes, ACPI is enabled in the BIOS setup, and recognized during the boot... (ACPI APIC Table: <compaq broadh2o="">) Thanks, Michele</compaq>

Check this: http://forum.pfsense.org/index.php/topic,64790  ;)

Updating the firmware to the latest release appears to have fixed whatever issue it was. I wish I was able to determine what happened, but don't have the knowledge on BSD to do so. I will put all my settings/packages back in place and see if this happens again. If it does not after a few weeks, then I will wipe the disc and reinstall fresh and chalk it up to some obscure setting or config that developed on the pfSense install. A hardware issue on the machine it was affecting would have been better as I would have found the issue I suppose. I don't like "not knowing" what would cause such a weird situation really. Oh well. Thank you to all the responses.

Sounds like you have a bit of testing on your hands.  Enjoy.

i found my answer! https://doc.pfsense.org/index.php/Remount_embedded_filesystem_as_read-write