Hello, Is this helps? : http://forum.pfsense.org/index.php/board,37.0.html cheers,

@m.econome: I installed version 1.2 on a VIA 501+ … On the console screen it shows the interfaces with configured IPs, if names etc. on top. Do both interfaces you're using have a  '*'  behind their names? Like:   WAN*                     ->   fxp0    ->      12.34.56.789(PPPoE)   OPT1(WLAN)            ->   xl0      ->      10.0.1.1   LAN*                      ->   fxp1    ->      192.168.1.1   OPT2(DMZ)*            ->   fxp2    ->      10.0.2.1 This would show a detected link at least and serve as a starting point for further trouble shooting. I have no link at the OPT1(WLAN) if in the example given above.

@soul710: still theres one issue. when booting, the machine hangs like 3 minutes when synching system time. is that normal? I think part of what is happening here is that the system is synchronizing over the network with an external time server (ntp). Perhaps in your case it is timing out. "Like 3 minutes" seems a bit long for that pause but its a while since I restarted my box.

A driver from a 6.3 kernel won't work with a 6.2 kernel - you need to use the same kernel and platform.

Thanks for your help as well!

Oooops, it happened to me several times… ;D Have fun m8! cheers,

http://forum.pfsense.org/index.php/topic,11016.msg61193.html#msg61193

The VLB sync patches you are referencing are for FreeBSD 4.x The structure of FreeBSD 6 (pfSense 1.2) and 7 (pfSense 1.2.1/1.3) is sufficiently different and the patches will not work. This is why I settled on m0n0wall 1.2 (based on FreeBSD 4) to run on my FireBox III. The only way to get the hardware working under modern FreeBSD would be to involve a developer familiar with the ata code, and I'm not sure there is much interest in getting this fixed. I saw someone was working on an OpenBSD based m0n0wall fork, but have not tried it. You could check it out here: http://www.thewaffle.org/

http://forum.pfsense.org/index.php/topic,7001.0.html

Thx a lot…..everything works fine now...

http://forum.pfsense.org/index.php/topic,7001.0.html –> http://devwiki.pfsense.org/OpenVPNasWAN

If the switch were ASUS GigaX 1024P then it's a bit confusing. Although the spec sheet doesn't say anything about .1Q but it does support .1Q, tag-base and/or port-base vlans. Eagleeye, you may want to configure your ASUS switch correctly, via CNM. Check your CNM manual, pp35, 4.7.5 VLAN setup.

I had the similar problem related to boot-time freezing related to several reasons. I had to enable the legacy USB support to fix that issue (provided that your BIOS allows that setting). For further setup hint, look at your MoBo and pull out every PCI/e etc device to see if the system boots normally (Live-CD) . Introduce the cards (and USB driven devices such as CF cards) one by one to see which one is the problem. I have Jetway J7F4K1G2E and BIOSTAR GF8200 M2+ (with AMD Athlon X2 -45W & Intel dual NIC pci-e) for my firewall/proxy. Jetway MoBo did not work with the PCI network cards. All sorts of freezing came down to PCI card issue. Still do not know why (although I have a hunch that it could be related to filmsy PCI extender or PCI-memory-overlap). I used a USB ethernet adapter to make it work. Go figure! For the Biostar MoBo I had legacy USB support issue as well. Also EHCI handout disabling needed. Good luck!

Can the pfsense LiveCD be extracted to a fat32/ext2 logical partition and be made bootable, either with 'GRUB' or 'SYSLINUX' ? Thank you.  :)

http://forum.pfsense.org/index.php/topic,7001.0.html

also anyone wanting to go the virtual machine root i found this program that is a gui for qemu www.kju-app.org its pretty good, universal binary.

For the sake of the archives (or if you still haven't resolved this) - this is ARP cache related on your ISP's side, the gateway of your firewall is hanging onto the old MAC address for that VIP for usually hours, you'll either have to wait or manually clear it in this circumstance.

Sounds like you're probably exhausting the state table, check your RRD graphs to see, and try increasing it.