Exactly, no arm support in pfSense. You could look at openwrt as an alternative. Steve

@poly_s: any thoughts on the realtex nics? Realtek 10/100 NICs are absolute trash.  Their Gig-E NICs are a bit better but I still feel strongly enough about them to say "crap". That said, I've used them in the past and they'll get the job done as long as you don't need more than a few hundred Mbit/s of throughput.

@armsby: That did not help, everything has been disabled, still only about 220-300Mbps and cpu load not over 50% With HT disabled you're fully tapping a core at 50% (which you might see as 70/30, 50/50, 90/10, etc.).  I'm still going to go with that's the cap for a 330, particularly since that's the same cap I hit a few years back.

Looked a bit more and stephen was right the haswell core i3s tend to support AES so that is a good thing. Those new atoms do look lovely and very low power also http://www.anandtech.com/show/7453/ecs-reveals-bay-traild-miniitx-line Only thing is I see no pci express slots,  vital to have one.  I am unsure if anyone has attempted a mini express network card and its worked with pfsense…. but if the performance of these baytrails are good and mini express network cards worked then they would make awesome pfsense boxes.

I have the same problem with error 22 on pfsense 2.01 Can anyone help? It's not possible for me to go to Version 2.1 I have copied re_if.ko to /boot/kernel and have edited the loader.conf.local and the loader.conf. No success.

Ah, thanks for the correction. I think I must have confused that with some Intel mobo specs. Can't remember that either though.  ::) Anyway it won't effect compatibility with the driver. Steve

I sorted it out by both reconnecting the modem to the port cuaU0.0 and adding an antenna to the dongle in order to have a better gain (was <45% now is >55%). Now the loadbalancing is working fine. Regards Mirco

bge0 and bge1 are on board broadcom gigabit ethernet and yes, I have a NC34T card :-)

For a small fanless (quiet) and reasonably powerful pfSense box, I'd go with a Habey BIS-6634 Intel Atom N2800 Fanless 4 Gigabit Ethernet with Bypass Segment Server/Security/Network Appliance.

Yes, that's a known bug and has been fixed for future snapshots. It's a problem with bridging on some NICs/drivers.  A fix is available here: http://forum.pfsense.org/index.php/topic,66908.msg367991.html#msg367991 Steve

I found the issue and it was unrelated to PfSense. The access point that he is using has AP isolation turned on by default. In order to get things working I had to enable a setting called "Allow Intra-AP communication" and all is well now. Thanks for everyone's help.

$60 is a good price for that part, I think I paid $180 on Newegg.com for the Intel part. Can't beat Intel Nics!

thx alu That is good news to hear about the Asrock mobos,I think as you suggested though best to find a 4 nic NC364T version.  I see plenty on ebay while more expensive I think as you suggested at least its better. Yeah the issue is with just about every motherboard I see they all ship with realtek nics !  its like a disease ;) I think I will go ahead with this build this week.  I need to get a reliable and stable router system in place one geared for OpenVPN performance.  This should hopefully do the trick !

@tguldener: Working driver for DS47 https://forum.pfsense.org/index.php/topic,65355.msg365028.html#msg365028 Awesome, thank you very much!  8)

@rippz: I think with this beast I can handle 4x32mbit multi wan (full speed when downloading with multiple connections). Without breaking a sweat I would think.  ;) Steve